ISP1582 - Philips Semiconductors / NXP Semiconductors

ISP1582

Hi-Speed Universal Serial Bus peripheral controller

Rev. 03 — 25 August 2004 Preliminary data

1. General description

The ISP1582 is a cost-optimized and feature-optimized Hi-Speed Universal Serial

Bus (USB) peripheral controller. It fully complies with

Universal Serial Bus

Speciﬁcation Rev. 2.0

, supporting data transfer at high-speed (480 Mbit/s) and

full-speed (12 Mbit/s).

The ISP1582 provides high-speed USB communication capacity to systems based

on microcontrollers or microprocessors. It communicates with a microcontroller or

microprocessor of a system through a high-speed general-purpose parallel interface.

The ISP1582 supports automatic detection of Hi-Speed USB system operation.

Original USB fall-back mode allows the device to remain operational under full-speed

conditions. It is designed as a generic USB peripheral controller so that it can ﬁt into

all existing device classes, such as imaging class, mass storage devices,

communication devices, printing devices and human interface devices.

The internal generic Direct Memory Access (DMA) block allows easy integration into

data streaming applications.

The modular approach to implementing a USB peripheral controller allows the

designer to select the optimum system microcontroller from the wide variety available.

The ability to reuse existing architecture and ﬁrmware investments shortens the

development time, eliminates risk and reduces cost. The result is fast and efﬁcient

development of the most cost-effective USB peripheral solution.

The ISP1582 is ideally suited for many types of peripherals, such as: printers,

scanners, digital still cameras, USB-to-Ethernet links, cable and DSL modems. The

low power consumption during suspend mode allows easy design of equipment that

is compliant to the ACPI™, OnNow™ and USB power management requirements.

The ISP1582 also incorporates features such as SoftConnect™, a reduced

frequency crystal oscillator, and integrated termination resistors. These features allow

signiﬁcant cost savings in system design and easy implementation of advanced USB

functionality into PC peripherals.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 2 of 66

2. Features

■Complies fully with:

◆

Universal Serial Bus Speciﬁcation Rev. 2.0

◆Most Device Class speciﬁcations

◆ACPI™, OnNow™ and USB power management requirements.

■Supports data transfer at high-speed (480 Mbit/s) and full-speed (12 Mbit/s)

■High performance USB peripheral controller with integrated Serial Interface

Engine (SIE), Parallel Interface Engine (PIE), FIFO memory and data transceiver

■Automatic Hi-Speed USB mode detection and Original USB fall-back mode

■Supports sharing mode

■Supports VBUS sensing

■High-speed DMA interface

■Fully autonomous and multiconﬁguration DMA operation

■7 IN endpoints, 7 OUT endpoints and a ﬁxed control IN/OUT endpoint

■Integrated physical 8 kbytes of multiconﬁguration FIFO memory

■Endpoints with double buffering to increase throughput and ease real-time data

transfer

■Bus-independent interface with most microcontrollers and microprocessors

■12 MHz crystal oscillator with integrated PLL for low EMI

■Software-controlled connection to the USB bus (SoftConnect™)

■Low-power consumption in operation and power-down modes; suitable for use in

bus-powered USB devices

■Supports Session Request Protocol (SRP) that complies with

On-The-Go

Supplement to the USB Speciﬁcation Rev. 1.0a

■Internal power-on and low-voltage reset circuits; also supports software reset

■Operation over the extended USB bus voltage range (DP, DM and VBUS)

■5 V tolerant I/O pads at 3.3 V

■Operating temperature range from −40 °C to +85 °C

■Available in HVQFN56 halogen-free and lead-free package.

3. Applications

■Personal digital assistant

■Digital video camera

■Digital still camera

■3G mobile phone

■MP3 player

■Communication device, for example: router and modem

■Printer

■Scanner.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 3 of 66

4. Abbreviations

DMA — Direct Memory Access

EMI — ElectroMagnetic Interference

FS — Full-speed

GDMA — Generic DMA

HS — High-speed

MMU — Memory Management Unit

NRZI — Non-Return-to-Zero Inverted

OTG — On-The-Go

PDA — Personal Digital Assistant

PID — Packet IDentiﬁer

PIE — Parallel Interface Engine

PIO — Parallel Input/Output

PLL — Phase-Locked Loop

SE0 — Single-Ended zero

SIE — Serial Interface Engine

SRP — Session Request Protocol

USB — Universal Serial Bus.

5. Ordering information

Table 1: Ordering information

Type

number Package

Name Description Version

ISP1582BS HVQFN56 plastic thermal enhanced very thin quad ﬂat package;

no leads; 56 terminals; body 8 ×8×0.85 mm SOT684-1

xxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx x xxxxxxxxxxxxxx xxxxxxxxxx xxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx

xxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx

xxxxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxx x x

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 4 of 66

6. Block diagram

Fig 1. Block diagram.

1.5

kΩ

12.0

kΩ

VCC

004aaa199

ISP1582

MEMORY

MANAGEMENT

UNIT

INTEGRATED

RAM

(8 KBYTES)

SYSTEM

CONTROLLER

VOLTAGE

REGULATORS

POWER-ON

RESET

HI-SPEED USB

TRANSCEIVER

internal

reset

SoftConnect

analog supply

digital

supply

I/O pad

supply

MICRO-

CONTROLLER

HANDLER

MICRO-

CONTROLLER

INTERFACE

OTG SRP

MODULE

DMA

REGISTERS

DMA

HANDLER DMA

INTERFACE

PHILIPS

SIE/PIE

INT

DATA[15:0]

A[7:0]

DACK

3.3 V

VCC(1V8) SUSPEND WAKEUPAGNDDGND

3.3 V

RD_N

EOT

VCC(I/O)

1, 5

DREQ DIOR

DIOW

9101112

13, 26,

29, 41

CS_N

WR_N

18 to 20,

22 to 25,

21, 34, 4828, 50

30 to 33,

35 to 40,

42 to 47

12 MHz

XTAL2XTAL1

to/from USB

DMDP VBUS

43495251

53, 54

5556

RPU

RREF

RESET_N

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 5 of 66

7. Pinning information

7.1 Pinning

Fig 2. Pin conﬁguration HVQFN56 (top view).

Fig 3. Pin conﬁguration HVQFN56 (bottom view).

DATA0

DATA1

DATA2

DATA10

VCC(I/O)

DATA4

DATA5

DATA6

DATA7

DATA8

DATA9

DGND

DATA13

DATA14

CS_N

RD_N

WR_N

DGND

VCC(1V8)

SUSPEND

DATA15

VCC(1V8)

VBUS

XTAL1

XTAL2

DATA12

DATA11

VCC

VCC(I/O)

DATA3

WAKEUP

VCC

DGND

VCC(I/O)

004aaa536

ISP1582BS

1 42

INT

DIOW

DIOR

DGND

DREQ

DACK

RESET_N

EOT

AGND

RREF

RPU

AGND

DGND

DATA9

DATA8

DGND

DATA6

DATA5

DATA4

VCC(I/O)

DATA3

DATA2

DATA1

DATA0

DGND

AGND

RPU

RREF

AGND

EOT

RESET_N

DACK

DIOR

DREQ

DGND

INT

SUSPEND

WAKEUP

VCC

XTAL1

XTAL2

VBUS

VCC(I/O)

DATA15

DATA14

DATA13

DATA12

DATA11

CS_N

VCC(I/O)

DIOW

VCC(1V8)

DATA7

RD_N

WR_N

DATA10

VCC(1V8)

VCC

004aaa377

ISP1582BS

14 29

Bottom View

terminal 1

GND (exposed die pad)

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 6 of 66

7.2 Pin description

Table 2: Pin description

Symbol[1] Pin Type[2] Description

AGND 1 - analog ground

RPU 2 A connect to the external pull-up resistor for pin DP; must be

connected to 3.3 V via a 1.5 kΩ resistor

DP 3 A USB D+ line connection (analog)

DM 4 A USB D− line connection (analog)

AGND 5 - analog ground

RREF 6 A connect to the external bias resistor; must be connected to

ground via a 12.0 kΩ±1 % resistor

RESET_N 7 I reset input (500 µs); a LOW level produces an asynchronous

reset; connect to VCC for the power-on reset (internal POR

circuit)

TTL; 5 V tolerant

EOT 8 I End-of-transfer input (programmable polarity); used in DMA

slave mode only; when not in use, connect this pin to VCC(I/O)

through a 10 kΩ resistor

input pad; TTL; 5 V tolerant

DREQ 9 O DMA request (programmable polarity) output; when not in

use, connect this pin to ground through a 10 kΩresistor; see

Table 54 and Table 55

TTL; 4 ns slew-rate control

DACK 10 I DMA acknowledge input (programmable polarity); when not

in use, connect this pin to VCC(I/O) through a 10 kΩ resistor;

see Table 54 and Table 55

TTL; 5 V tolerant

DIOR 11 I DMA read strobe input (programmable polarity); when not in

use, connect this pin to VCC(I/O) through a 10 kΩresistor; see

Table 54 and Table 55

TTL; 5 V tolerant

DIOW 12 I DMA write strobe input (programmable polarity); when not in

use, connect this pin to VCC(I/O) through a 10 kΩresistor; see

Table 54 and Table 55

TTL; 5 V tolerant

DGND 13 - digital ground

INT 14 O interrupt output; programmable polarity (active HIGH or

LOW) and signaling (edge or level triggered)

CMOS output; 8 mA drive

CS_N 15 I chip select input

input pad; TTL; 5 V tolerant

RD_N 16 I read strobe input

input pad; TTL; 5 V tolerant

WR_N 17 I write strobe input

input pad; TTL; 5 V tolerant

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 7 of 66

A0 18 I bit 0 of the address bus

input pad; TTL; 5 V tolerant

A1 19 I bit 1 of the address bus

input pad; TTL; 5 V tolerant

A2 20 I bit 2 of the address bus

input pad; TTL; 5 V tolerant

VCC(I/O)[3] 21 - supply voltage; used to supply voltage to the I/O pads; see

Section 8.14

A3 22 I bit 3 of the address bus

input pad; TTL; 5 V tolerant

A4 23 I bit 4 of the address bus

input pad; TTL; 5 V tolerant

A5 24 I bit 5 of the address bus

input pad; TTL; 5 V tolerant

A6 25 I bit 6 of the address bus

input pad; TTL; 5 V tolerant

DGND 26 - digital ground

A7 27 I bit 7 of the address bus

input pad; TTL; 5 V tolerant

VCC(1V8)[3] 28 - regulator output voltage (1.8 V ±0.15 V); tapped out voltage

from the internal regulator; this regulated voltage cannot

drive external devices; decouple this pin using a 0.1 µF

capacitor; see Section 8.14

DGND 29 - digital ground

DATA0 30 I/O bit 0 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA1 31 I/O bit 1 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA2 32 I/O bit 2 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA3 33 I/O bit 3 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

VCC(I/O)[3] 34 - supply voltage; used to supply voltage to the I/O pads; see

Section 8.14

DATA4 35 I/O bit 4 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA5 36 I/O bit 5 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA6 37 I/O bit 6 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA7 38 I/O bit 7 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

Table 2: Pin description

…continued

Symbol[1] Pin Type[2] Description

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 8 of 66

DATA8 39 I/O bit 8 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA9 40 I/O bit 9 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DGND 41 - digital ground

DATA10 42 I/O bit 10 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA11 43 I/O bit 11 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA12 44 I/O bit 12 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA13 45 I/O bit 13 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA14 46 I/O bit 14 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

DATA15 47 I/O bit 15 of bidirectional data bus

bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant

VCC(I/O)[3] 48 - supply voltage; used to supply voltage to the I/O pads; see

Section 8.14

VBUS 49 A USB bus power pin sensing input; used to detect whether

the host is connected or not; it is an output for VBUS pulsing

in OTG mode; when VBUS is not detected, pin RPU is

internally disconnected from pin DP in approximately 4 ns;

connect a 1 µF electrolytic capacitor and a 1 MΩ pull-down

resistor to ground; see Section 8.12

5 V tolerant

VCC(1V8)[3] 50 - regulator output voltage (1.8 V ±0.15 V); tapped out voltage

from the internal regulator; this regulated voltage can drive

external devices up to 1 mA; decouple this pin using 4.7 µF

and 0.1 µF capacitors; see Section 8.14

XTAL2 51 O crystal oscillator output (12 MHz); connect a fundamental

parallel-resonant crystal; leave this pin open-circuit when

using an external clock source on pin XTAL1; see Table 83

XTAL1 52 I crystal oscillator input (12 MHz); connect a fundamental

parallel-resonant crystal or an external clock source (leaving

pin XTAL2 unconnected); see Table 83

VCC[3] 53 - supply voltage (3.3 V ±0.3 V); this pin supplies the internal

voltage regulator and the analog circuit; see Section 8.14

VCC[3] 54 - supply voltage (3.3 V ±0.3 V); this pin supplies the internal

voltage regulator and the analog circuit; see Section 8.14

Table 2: Pin description

…continued

Symbol[1] Pin Type[2] Description

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 9 of 66

[1] Symbol names ending with underscore N (for example, NAME_N) represent active LOW signals.

[2] All outputs and I/O pins can source 4 mA.

[3] Add a decoupling capacitor (0.1 µF) to all the supply pins. For better EMI results, add a 0.01 µF

capacitor in parallel to the 0.1 µF.

WAKEUP 55 I wake-up input; when this pin is at the HIGH level, the chip is

prevented from getting into the suspend state and the chip

wakes up from the suspend state; when not in use, connect

this pin to ground through a 10 kΩ resistor

input pad; TTL; 5 V tolerant

SUSPEND 56 O suspend state indicator output; used as a power switch

control output for powered-off application or as a resume

signal to the CPU for powered-on application

CMOS output; 8 mA drive

GND exposed

die pad - ground supply; down bonded to the exposed die pad

(heatsink); to be connected to DGND during PCB layout

Table 2: Pin description

…continued

Symbol[1] Pin Type[2] Description

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 10 of 66

8. Functional description

The ISP1582 is a high-speed USB peripheral controller. It implements the Hi-Speed

USB or the Original USB physical layer and the packet protocol layer. It maintains up

to 16 USB endpoints concurrently (control IN and control OUT, 7 IN and 7 OUT

conﬁgurable) along with endpoint EP0 setup, which accesses the setup buffer. The

USB Chapter 9 protocol handling is executed by means of external ﬁrmware.

For high-bandwidth data transfer, the integrated DMA handler can be invoked to

transfer data to or from external memory or devices. The DMA interface can be

conﬁgured by writing to the proper DMA registers (see Section 9.4).

The ISP1582 supports Hi-Speed USB and Original USB signaling. The USB

signaling speed is automatically detected.

The ISP1582 has 8 kbytes of internal FIFO memory, which is shared among the

enabled USB endpoints.

There are 7 IN endpoints, 7 OUT endpoints and 2 control endpoints that are a ﬁxed

64 bytes long. Any of the 7 IN and 7 OUT endpoints can be separately enabled or

disabled. The endpoint type (interrupt, isochronous or bulk) and packet size of these

endpoints can be individually conﬁgured depending on the requirements of the

application. Optional double buffering increases the data throughput of these data

endpoints.

The ISP1582 requires 3.3 V power supply. It has 5 V tolerant I/O pads when

operating at VCC(I/O) = 3.3 V and an internal 1.8 V regulator for powering the analog

transceiver.

The ISP1582 operates on a 12 MHz crystal oscillator. An integrated 40 ×PLL clock

multiplier generates the internal sampling clock of 480 MHz.

8.1 DMA interface, DMA handler and DMA registers

The DMA block can be subdivided into two blocks: the DMA handler and the DMA

interface.

The ﬁrmware writes to the DMA command register to start a DMA transfer (see

Table 47). The command opcode determines whether a generic DMA or PIO transfer

will start. The handler interfaces to the same FIFO (internal RAM) as used by the

USB core. On receiving the DMA command, the DMA handler directs the data from

the endpoint FIFO to the external DMA device or from the external DMA device to the

endpoint FIFO.

The DMA interface conﬁgures the timing and the DMA handshake. Data can be

transferred using either the DIOR and DIOW strobes or by the DACK and DREQ

handshakes. The DMA conﬁgurations are set up by writing to the DMA Conﬁguration

For a generic DMA interface, Generic DMA (GDMA) slave mode can be used.

Remark: The DMA endpoint buffer length must be a multiple of 4 bytes.

For details on DMA registers, see Section 9.4.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 11 of 66

8.2 Hi-Speed USB transceiver

The analog transceiver directly interfaces to the USB cable through integrated

termination resistors. The high-speed transceiver requires an external resistor

(12.0 kΩ±1 %) between pin RREF and ground to ensure an accurate current mirror

that generates the Hi-Speed USB current drive. A full-speed transceiver is integrated

as well. This makes the ISP1582 compliant to Hi-Speed USB and Original USB,

supporting both the high-speed and full-speed physical layers. After automatic speed

detection, the Philips Serial Interface Engine (SIE) sets the transceiver to use either

high-speed or full-speed signaling.

8.3 MMU and integrated RAM

The Memory Management Unit (MMU) and the integrated RAM provide the

conversion between the USB speed (full-speed: 12 Mbit/s, high-speed: 480 Mbit/s)

and the microcontroller handler or the DMA handler. The data from the USB bus is

stored in the integrated RAM, which is cleared only when the microcontroller has read

or written all data from or to the corresponding endpoint buffer or when the DMA

handler has read or written all data from or to the endpoint buffer. The OUT endpoint

buffer can also be cleared forcibly by setting bit CLBUF in the Control Function

8.4 Microcontroller interface and microcontroller handler

The microcontroller handler allows the external microcontroller or microprocessor to

access the register set in the Philips SIE as well as the DMA handler. The

initialization of the DMA conﬁguration is done through the microcontroller handler.

8.5 OTG SRP module

The OTG supplement deﬁnes a Session Request Protocol (SRP), which allows a

B-device to request the A-device to turn on VBUS and start a session. This protocol

allows the A-device, which may be battery-powered, to conserve power by turning off

VBUS when there is no bus activity while still providing a means for the B-device to

initiate bus activity.

Any A-device, including a PC or laptop, can respond to SRP. Any B-device, including

a standard USB peripheral, can initiate SRP.

The ISP1582 is a device that can initiate SRP.

8.6 Philips high-speed transceiver

8.6.1 Philips Parallel Interface Engine (PIE)

In the high-speed (HS) transceiver, the Philips PIE interface uses a 16-bit parallel

bidirectional data interface. The functions of the HS module also include bit-stufﬁng or

destufﬁng and Non-Return-to-Zero Inverted (NRZI) encoding or decoding logic.

8.6.2 Peripheral circuit

To maintain a constant current driver for HS transmit circuits and to bias other analog

circuits, an internal band gap reference circuit and an RREF resistor form the

reference current. This circuit requires an external precision resistor (12.0 kΩ±1%)

connected to the analog ground.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 12 of 66

8.6.3 HS detection

The ISP1582 handles more than one electrical state—full-speed (FS) or high-speed

(HS)—under the USB speciﬁcation. When the USB cable is connected from the

peripheral to the host controller, the ISP1582 defaults to the FS state until it sees a

bus reset from the host controller.

During the bus reset, the peripheral initiates an HS chirp to detect whether the host

controller supports Hi-Speed USB or Original USB. Chirping must be done with the

pull-up resistor connected and the internal termination resistors disabled. If the HS

handshake shows that there is an HS host connected, then the ISP1582 switches to

the HS state.

In the HS state, the ISP1582 should observe the bus for periodic activity. If the bus

remains inactive for 3 ms, the peripheral switches to the FS state to check for a

Single-Ended Zero (SE0) condition on the USB bus. If an SE0 condition is detected

for the designated time (100 µs to 875 µs; refer to section 7.1.7.6 of the USB

speciﬁcation Rev. 2.0), the ISP1582 switches to the HS chirp state to perform an HS

detection handshake. Otherwise, the ISP1582 remains in the FS state adhering to the

bus-suspend speciﬁcation.

8.7 Philips Serial Interface Engine (SIE)

The Philips SIE implements the full USB protocol layer. It is completely hardwired for

speed and needs no ﬁrmware intervention. The functions of this block include:

synchronization pattern recognition, parallel or serial conversion, bit (de)stufﬁng,

CRC checking or generation, Packet IDentiﬁer (PID) veriﬁcation or generation,

address recognition, handshake evaluation or generation.

8.8 SoftConnect

The connection to the USB is established by pulling pin DP (for full-speed devices)

HIGH through a 1.5 kΩ pull-up resistor. In the ISP1582, an external 1.5 kΩ pull-up

resistor must be connected between pin RPU and 3.3 V. Pin RPU connects the

pull-up resistor to pin DP, when bit SOFTCT in the Mode register is set (see Table 20

and Table 21). After a hardware reset, the pull-up resistor is disconnected by default

(bit SOFTCT = 0). The USB bus reset does not change the value of bit SOFTCT.

When the VBUS is not present, the SOFTCT bit must be set to logic 0 to comply with

the back-drive voltage.

8.9 System controller

The system controller implements the USB power-down capabilities of the ISP1582.

Registers are protected against data corruption during wake-up following a resume

(from the suspend state) by locking the write access until an unlock code has been

written in the Unlock Device register (see Table 73 and Table 74).

8.10 Output pins status

Table 3 illustrates the behavior of output pins when VCC(I/O) is supplied with VCC in

various operating conditions.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 13 of 66

[1] X: Don’t care.

[2] Dead: The USB cable is plugged-out and VCC(I/O) is not available.

[3] Plug-out: The USB cable is not present but VCC(I/O) is available.

[4] Plug-in: The USB cable is being plugged-in and VCC(I/O) is available.

8.11 Interrupt

8.11.1 Interrupt output pin

The Interrupt Conﬁguration register of the ISP1582 controls the behavior of the INT

output pin. The polarity and signaling mode of pin INT can be programmed by setting

bits INTPOL and INTLVL of the Interrupt Conﬁguration register (R/W: 10h); see

Table 24. Bit GLINTENA of the Mode register (R/W: OCh) is used to enable pin INT.

Default settings after reset are active LOW and level mode. When pulse mode is

selected, a pulse of 60 ns is generated when the OR-ed combination of all interrupt

bits changes from logic 0 to logic 1.

Figure 4 shows the relationship between the interrupt events and pin INT.

Each of the indicated USB and DMA events is logged in a status bit of the Interrupt

the Interrupt Enable register and the DMA Interrupt Enable register determine

whether or not an event will generate an interrupt.

Interrupts can be masked globally by means of bit GLINTENA of the Mode register;

see Table 21.

Field CDBGMOD[1:0] of the Interrupt Conﬁguration register controls the generation

of the INT signals for the control pipe. Field DDBGMODIN[1:0] of the Interrupt

Conﬁguration register controls the generation of the INT signals for the IN pipe. Field

DDBGMODOUT[1:0] of the Interrupt Conﬁguration register controls the generation of

the INT signals for the OUT pipe; see Table 25.

Table 3: ISP1582 pin status[1]

VCC VCC(I/O) State Pin

RESET_N INT_N SUSPEND DREQ DATA[15:0]

0V V

CC dead[2] XXXXX

0V V

CC plug-out[3] X LOW HIGH high-Z input

0V−> 3.3 V VCC plug-in[4] X LOW HIGH high-Z high-Z

3.3 V VCC reset LOW HIGH LOW high-Z high-Z

3.3 V VCC normal HIGH HIGH LOW high-Z high-Z

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx

xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 14 of 66

Fig 4. Interrupt logic.

Interrupt register

DMA Interrupt Reason

DMA Interrupt Enable

Interrupt Enable register

DMA_XFER_OK

EXT_EOT

INT_EOT

IE_DMA_XFER_OK

IE_EXT_EOT

IE_INT_EOT

IEBRESET

IESOF

IEDMA

IEP7RX

IEP7TX

BRESET

SOF

DMA

EP7RX

EP7TX

....................

..........

004aaa275

LATCH

GLINTENA

INTPOL

Interrupt Configuration

Mode register

INT PULSE/LEVEL

GENERATOR

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 15 of 66

8.11.2 Interrupt control

Bit GLINTENA in the Mode register is a global enable/disable bit. The behavior of this

bit is given in Figure 5.

Event A: When an interrupt event occurs (for example, SOF interrupt) with

bit GLINTENA set to logic 0, an interrupt will not be generated at pin INT. It will,

however, be registered in the corresponding Interrupt register bit.

Event B: When bit GLINTENA is set to logic 1, pin INT is asserted because bit SOF in

the Interrupt register is already set.

Event C: If the ﬁrmware sets bit GLINTENA to logic 0, pin INT will still be asserted.

The bold dashed line shows the desired behavior of pin INT.

Deassertion of pin INT can be achieved either by clearing all the Interrupt register or

the DMA Interrupt Reason register, depending on the event.

Remark: When clearing an interrupt event, perform write to all the bytes of the

For more information on interrupt control, see Section 9.2.2,Section 9.2.5 and

Section 9.5.1.

8.12 VBUS sensing

Pin VBUS is one of the ways to wake up the clock when the ISP1582 is suspended

with bit CLKAON set to logic 0 (clock off option).

To detect whether the host is connected or not, that is VBUS sensing, a 1 MΩresistor

and a 1 µF electrolytic capacitor must be added to damp the overshoot upon plug-in.

Pin INT: HIGH = deassert; LOW = assert (individual interrupts are enabled).

Fig 5. Behavior of bit GLINTENA.

INT pin

004aaa394

GLINTENA = 0

SOF asserted

GLINTENA = 1

SOF asserted

GLINTENA = 0

(during this time,

an interrupt event

occurs. For example,

SOF asserted.)

ABC

Fig 6. Resistor and electrolytic capacitor needed for VBUS sensing.

1 MΩ

ISP1582

004aaa440

+1 µF

49 USB

Connector

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 16 of 66

8.13 Power-on reset

The ISP1582 requires a minimum pulse width of 500 µs.

Pin RESET_N can be either connected to VCC (using the internal POR circuit) or

externally controlled (by the microcontroller, ASIC, and so on). When VCC is directly

connected to pin RESET_N, the internal pulse width tPORP will be typically 200 ns.

The power-on reset function can be explained by viewing the dips at t2-t3 and t4-t5

on the VCC(POR) curve (Figure 9).

t0 — The internal POR starts with a HIGH level.

t1 — The detector will see the passing of the trip level and a delay element will add

another tPORP before it drops to LOW.

t2-t3 — The internal POR pulse will be generated whenever VCC(POR) drops below

Vtrip for more than 11 µs.

t4-t5 — The dip is too short (< 11 µs) and the internal POR pulse will not react and

will remain LOW.

Figure 10 shows the availability of the clock with respect to the external POR.

Fig 7. Oscilloscope reading: no resistor

and capacitor in the network. Fig 8. Oscilloscope reading: with

resistor and capacitor in the

network.

004aaa441 004aaa442

(1) PORP = power-on reset pulse.

Fig 9. POR timing.

004aaa389

VBAT(POR)

t0 t1 t2 t3 t4 t5

Vtrip

tPORP PORP(1)

tPORP

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 17 of 66

8.14 Power supply

The ISP1582 can be powered by 3.3 V ±0.3 V, and 3.3 V at the interface. For

connection details, see Figure 11.

If the ISP1582 is powered by VCC = 3.3 V, an integrated 3.3 V-to-1.8 V voltage

regulator provides a 1.8 V supply voltage for the internal logic.

In sharing mode (that is, when VCC is not present and VCC(I/O) is present), all the I/O

pins are in three-state, the interrupt pin is connected to ground, and the suspend pin

is connected to VCC(I/O). See Table 3.

Stable external clock is to be available at A.

Fig 10. Clock with respect to the external POR.

POR

EXTERNAL CLOCK

004aaa365

(1) It is mandatory to use a 4.7 µF electrolytic capacitor on VCC(1V8).

Fig 11. ISP1582 with 3.3 V supply.

004aaa203

53, 54

VCC(I/O)

ISP1582

3.3 V ± 0.3 V

VCC(I/O)

VCC

VCC(I/O)

VCC(1V8)

4.7 µF(1) 0.1 µF

0.01 µF 0.1 µF

VCC(1V8)

0.1 µF

VCC

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 18 of 66

Table 4 shows power modes in which the ISP1582 can be operated.

[1] Power supply to the IC (VCC) is 3.3 V. Therefore, if the application is bus-powered, a 3.3 V regulator

needs to be used.

[2] VCC(I/O) =V

CC. If the application is bus-powered, a voltage regulator needs to be used.

8.14.1 Power-sharing mode

As can be seen in Figure 12, in power-sharing mode, VCC is supplied by the output of

the 5 V-to-3.3 V voltage regulator. The input to the regulator is from VBUS. VCC(I/O) is

supplied through the power source of the system. When the USB cable is plugged in,

the ISP1582 goes through the power-on reset cycle. In this mode, OTG is disabled.

The processor will experience continuous interrupt because the default status of the

interrupt pin when operating in sharing mode with the VBUS not present is LOW. To

overcome this, implement external VBUS sensing circuitry. The output from the voltage

regulator can be connected to pin GPIO of the processor to qualify the interrupt from

the ISP1582.

Remark: When the core power is removed, the ISP1582 must be reset using the

RESET_N pin. The reset pulse width must be 2 ms.

Table 4: Power modes

VCC VCC(I/O) Power mode

VBUS[1] VBUS[2] bus-powered

self-powered self-powered self-powered

VBUS[1] self-powered power-sharing (hybrid)

Fig 12. Power-sharing mode.

004aaa457

ISP1582

−

5 V-to-3.3 V

USB

VOLTAGE

REGULATOR

To GPIO of processor

for sensing VBUS

1 MΩ

VCC

VCC(I/O)

VBUS

RPU VBUS

1 µF +

−

1.5 kΩ

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 19 of 66

Fig 13. Interrupt pin status during power off in power-sharing mode.

Table 5: Operation truth table for SoftConnect

ISP1582 operation Power supply Bit SOFTCT in

Mode register

VCC VCC(I/O) RPU

(3.3 V) VBUS

Normal bus operation 3.3 V 3.3 V 3.3 V 5 V enabled

Core power is lost 0 V 3.3 V 0 V 0 V not applicable

Table 6: Operation truth table for clock off during suspend

ISP1582 operation Power supply Clockoff during

suspend

VCC VCC(I/O) RPU

(3.3 V) VBUS

Clock will wake up:

After resume and

After a bus reset

3.3 V 3.3 V 3.3 V 5 V enabled

Core power is lost 0 V 3.3 V 0 V 0 V not applicable

Table 7: Operation truth table for back voltage compliance

ISP1582 operation Power supply Bit SOFTCT in

Mode register

VCC VCC(I/O) RPU

(3.3 V) VBUS

Back voltage is not measured in this

mode 3.3 V 3.3 V 3.3 V 5 V enabled

Back voltage is not an issue because

core power is lost 0 V 3.3 V 0 V 0 V not applicable

Table 8: Operation truth table for OTG

ISP1582 operation Power supply OTG register

VCC VCC(I/O) RPU

(3.3 V) VBUS

SRP is not applicable 3.3 V 3.3 V 3.3 V 5 V not applicable

OTG is not possible because VBUS is

not present and so core power is lost 0 V 3.3 V 0 V 0 V not applicable

004aaa469

VCC(I/O)

VCC

INT

power off power off

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 20 of 66

8.14.2 Self-powered mode

In self-powered mode, VCC and VCC(I/O) are supplied by the system. Bit SOFTCT in

the Mode register must be always logic 1. See Figure 14.

[1] When the USB cable is removed, SoftConnect is disabled.

Fig 14. Self-powered mode.

Table 9: Operation truth table for SoftConnect

ISP1582 operation Power supply Bit SOFTCT in

Mode register

VCC VCC(I/O) RPU

(3.3 V) VBUS

Normal bus operation 3.3 V 3.3 V 3.3 V 5 V enabled

No pull-up on DP 3.3 V 3.3 V 3.3 V 0 V[1] disabled

Table 10: Operation truth table for clock off during suspend

ISP1582 operation Power supply Clock off

during

suspend

VCC VCC(I/O) RPU

(3.3 V) VBUS

Clock will wake up:

After resume and

After a bus reset

3.3 V 3.3 V 3.3 V 5 V enabled

Clock will wake up:

After detecting the presence of VBUS

3.3 V 3.3 V 3.3 V 0 V => 5 V enabled

Table 11: Operation truth table for back voltage compliance

ISP1582 operation Power supply Bit SOFTCT

in Mode

VCC VCC(I/O) RPU

(3.3 V) VBUS

Back voltage is not measured in this

mode 3.3 V 3.3 V 3.3 V 5 V enabled

Back voltage is not an issue because

pull-up on DP will not be present when

VBUS is not present

3.3 V 3.3 V 3.3 V 0 V disabled

004aaa460

ISP1582

−

USB

1 MΩ

VCC

VCC(I/O)

VBUS

RPU VBUS

1.5 kΩ

1 µF +

−

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 21 of 66

8.14.3 Bus-powered mode

In bus-powered mode (see Figure 15), VCC and VCC(I/O) are supplied by the output of

the 5 V-to-3.3 V voltage regulator. The input to the regulator is from VBUS. On

plugging in of the USB cable, the ISP1582 goes through the power-on reset cycle. In

this mode, OTG is disabled.

Table 12: Operation truth table for OTG

ISP1582 operation Power supply OTG

VCC VCC(I/O) RPU

(3.3 V) VBUS

SRP is not applicable 3.3 V 3.3 V 3.3 V 5 V not

applicable

SRP is possible 3.3 V 3.3 V 3.3 V 0 V operational

Fig 15. Bus-powered mode.

Table 13: Operation truth table for SoftConnect

ISP1582 operation Power supply Bit SOFTCT in

Mode register

VCC VCC(I/O) RPU

(3.3 V) VBUS

Normal bus operation 3.3 V 3.3 V 3.3 V 5 V enabled

Power loss 0 V 0 V 0 V 0 V not applicable

Table 14: Operation truth table for clock off during suspend

ISP1582 operation Power supply Clockoff during

suspend

VCC VCC(I/O) RPU

(3.3 V) VBUS

Clock will wake up:

After resume and

After a bus reset

3.3 V 3.3 V 3.3 V 5 V enabled

Power loss 0 V 0 V 0 V 0 V not applicable

004aaa462

ISP1582

5 V-to-3.3 V

USB

VOLTAGE

REGULATOR

1 MΩ

VCC

VCC(I/O)

VBUS VBUS

RPU

1 µF +

−

1.5 kΩ

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 22 of 66

Table 15: Operation truth table for back voltage compliance

ISP1582 operation Power supply Bit SOFTCT in

Mode register

VCC VCC(I/O) RPU

(3.3 V) VBUS

Back voltage is not measured in this

mode 3.3 V 3.3 V 3.3 V 5 V enabled

Power loss 0 V 0 V 0 V 0 V not applicable

Table 16: Operation truth table for OTG

ISP1582 operation Power supply OTG register

VCC VCC(I/O) RPU

(3.3 V) VBUS

SRP is not applicable 3.3 V 3.3 V 3.3 V 5 V not applicable

Power loss 0 V 0 V 0 V 0 V not applicable

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 23 of 66

9. Register description

Table 17: Register overview

Name Destination Address Description Size

(bytes) Reference

Initialization registers

Address device 00h USB device address and enabling 1 Section 9.2.1

on page 24

Mode device 0Ch power-down options, global interrupt

enable, SoftConnect 1Section 9.2.2

on page 25

Interrupt Conﬁguration device 10h interrupt sources, trigger mode, output

polarity 1Section 9.2.3

on page 27

OTG device 12h OTG implementation 1 Section 9.2.4

on page 28

Interrupt Enable device 14h interrupt source enabling 4 Section 9.2.5

on page 30

Data ﬂow registers

Endpoint Index endpoints 2Ch endpoint selection, data ﬂow direction 1 Section 9.3.1

on page 31

Control Function endpoint 28h endpoint buffer management 1 Section 9.3.2

on page 33

Data Port endpoint 20h data access to endpoint FIFO 2 Section 9.3.3

on page 33

Buffer Length endpoint 1Ch packet size counter 2 Section 9.3.4

on page 34

Buffer Status endpoint 1Eh buffer status for each endpoint 1 Section 9.3.5

on page 35

Endpoint MaxPacketSize endpoint 04h maximum packet size 2 Section 9.3.6

on page 36

Endpoint Type endpoint 08h selects endpoint type: control,

isochronous, bulk or interrupt 2Section 9.3.7

on page 37

DMA registers

DMA Command DMA controller 30h controls all DMA transfers 1 Section 9.4.1

on page 39

DMA Transfer Counter DMA controller 34h sets byte count for DMA transfer 4 Section 9.4.2

on page 40

DMA Conﬁguration DMA controller 38h sets GDMA conﬁguration (counter

enable, burst length, data strobing, bus

width)

1Section 9.4.3

on page 41

DMA Hardware DMA controller 3Ch endian type, master or slave selection,

signal polarity for DACK, DREQ, DIOW,

DIOR

1Section 9.4.4

on page 42

DMA Interrupt Reason DMA controller 50h shows reason (source) for DMA interrupt 2 Section 9.4.5

on page 43

DMA Interrupt Enable DMA controller 54h enables DMA interrupt sources 2 Section 9.4.6

on page 45

DMA Endpoint DMA controller 58h selects endpoint FIFO, data ﬂow direction 1 Section 9.4.7

on page 45

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 24 of 66

9.1 Register access

access. For single-byte registers, the upper byte (MSByte) must be ignored.

Endpoint speciﬁc registers are indexed via the Endpoint Index register. The target

endpoint must be selected before accessing the following registers:

•Buffer Length

•Buffer Status

•Control Function

•Data Port

•Endpoint MaxPacketSize

•Endpoint Type.

Remark: All reserved bits are not implemented. The bus and bus reset values are not

deﬁned. Therefore, writing to these reserved bits will have no effect.

9.2 Initialization registers

9.2.1 Address register (address: 00h)

This register sets the USB assigned address and enables the USB device. Table 18

shows the Address register bit allocation.

Bits DEVADDR will be cleared whenever a bus reset, a power-on reset or a soft reset

occurs. Bit DEVEN will be cleared whenever a power-on reset or a soft reset occurs,

and will be set after a bus reset.

DMA Burst Counter DMA controller 64h DMA burst counter 2 Section 9.4.8

on page 46

General registers

Interrupt device 18h shows interrupt sources 4 Section 9.5.1

on page 46

Chip ID device 70h product ID code and hardware version 3 Section 9.5.2

on page 48

Frame Number device 74h last successfully received

Start-Of-Frame: lower byte (byte 0) is

accessed ﬁrst

2Section 9.5.3

on page 49

Scratch device 78h allows save or restore of ﬁrmware status

during suspend 2Section 9.5.4

on page 49

Unlock Device device 7Ch reenables register access after suspend 2 Section 9.5.5

on page 50

Test Mode PHY 84h direct setting of DP and DM states,

internal transceiver test (PHY) 1Section 9.5.6

on page 51

Table 17: Register overview

…continued

Name Destination Address Description Size

(bytes) Reference

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 25 of 66

In response to the standard USB request SET_ADDRESS, the ﬁrmware must write

the (enabled) device address to the Address register, followed by sending an empty

packet to the host. The new device address is activated when the device receives

acknowledgment from the host.

9.2.2 Mode register (address: 0Ch)

This register consists of 2 bytes (bit allocation: see Table 20).

The Mode register controls resume, suspend and wake-up behavior, interrupt activity,

soft reset, clock signals and SoftConnect operation.

Table 18: Address register: bit allocation

Bit 76543210

Symbol DEVEN DEVADDR[6:0]

Reset 00000000

Bus reset 10000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 19: Address register: bit description

Bit Symbol Description

7 DEVEN Logic 1 enables the device.

6 to 0 DEVADDR[6:0] This ﬁeld speciﬁes the USB device address.

Table 20: Mode register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol reserved DMA

CLKON VBUSSTAT

Reset ------0-

Bus reset ------0-

Access RRRRRRR/WR

Bit 76543210

Symbol CLKAON SNDRSU GOSUSP SFRESET GLINTENA WKUPCS PWRON SOFTCT

Reset 00000000

Bus reset 0000unchanged 0 0 unchanged

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 21: Mode register: bit description

Bit Symbol Description

15 to 10 - reserved

9 DMACLKON 1 — Supply clock to the DMA circuit.

0 — Power save mode; the DMA circuit will stop completely to save

power.

8 VBUSSTAT This bit reﬂects the VBUS pin status.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 26 of 66

When SoftConnect and VBUS are not present (except in OTG), the USB bus activities

are not qualiﬁed. Therefore, the chip will follow the suspend command to enter

suspend mode (the clock is controlled by bit CLKAON).

When VBUS is off, the 1.5 kΩ pull-up resister is disconnected from pin DP in

approximately 4 ns via bit SOFTCT in the Mode register and a suspend interrupt is

set with some latency (debounce and disqualify USB trafﬁc).

When bit SOFTCT is set to logic 0, no interrupt is generated. The ﬁrmware can issue

a suspend command, followed by the resetting of bit SOFTCT to suspend the chip.

If OTG is logic 1, the pull-up resistor on pin DP depends on D+ line (VBUS sensing

status). Bit DP operates as normal, so the ﬁrmware must mask suspend and wake-up

interrupt events. When SRP is completed, the device should clear OTG.

7 CLKAON Clock Always On: Logic 1 indicates that the internal clocks are

always running when in the suspend state. Logic 0 switches off the

internal oscillator and PLL when the device goes into suspend

mode. The device will consume less power if this bit is set to logic 0.

The clock is stopped after a delay of approximately 2 ms, following

which bit GOSUSP is set.

6 SNDRSU Send Resume: Writing logic 1, followed by logic 0 will generate an

upstream resume signal of 10 ms duration, after a 5 ms delay.

5 GOSUSP Go Suspend: Writing logic 1, followed by logic 0 will activate

suspend mode.

4 SFRESET Soft Reset: Writing logic 1, followed by logic 0 will enable a

software-initiated reset to the ISP1582. A soft reset is similar to a

hardware-initiated reset (via pin RESET_N).

3 GLINTENA Global Interrupt Enable: Logic 1 enables all interrupts. Individual

interrupts can be masked by clearing the corresponding bits in the

Interrupt Enable register.

When this bit is not set, an unmasked interrupt will not generate an

interrupt trigger on the interrupt pin. If global interrupt, however, is

enabled while there is any pending unmasked interrupt, an interrupt

signal will be immediately generated on the interrupt pin. (If the

interrupt is set to pulse mode, the interrupt events that were

generated before the global interrupt is enabled may be dropped).

2 WKUPCS Wake up on Chip Select: Logic 1 enables wake-up from suspend

mode through a valid register read on the ISP1582. (A read will

invoke the chip clock to restart. If you write to the register before the

clock gets stable, it may cause malfunctioning).

1 PWRON Pin SUSPEND output control.

0 — Pin SUSPEND is HIGH when the ISP1582 is in the suspend

state. Otherwise, pin SUSPEND is LOW.

1 — When the device is woken up from the suspend state, there will

be a 1 ms active HIGH pulse on pin SUSPEND. Pin SUSPEND will

remain LOW in all other states.

0 SOFTCT SoftConnect: Logic 1 enables the connection of the 1.5 kΩ pull-up

resistor on pin RPU to the DP line. Bus reset value: unchanged.

Table 21: Mode register: bit description

…continued

Bit Symbol Description

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 27 of 66

If OTG is logic 0, the status of the pull-up resistor on DP is referred to in Table 22.

9.2.3 Interrupt Conﬁguration register (address: 10h)

This 1-byte register determines the behavior and polarity of the INT output. The bit

allocation is shown in Table 23. When the USB SIE receives or generates an ACK,

NAK or STALL, it will generate interrupts depending on three Debug mode ﬁelds.

CDBGMOD[1:0] — Interrupts for the control endpoint 0

DDBGMODIN[1:0] — Interrupts for the DATA IN endpoints 1 to 7

DDBGMODOUT[1:0] — Interrupts for the DATA OUT endpoints 1 to 7.

The Debug mode settings for CDBGMOD, DDBGMODIN and DDBGMODOUT allow

you to individually conﬁgure when the ISP1582 sends an interrupt to the external

microprocessor. Table 25 lists the available combinations.

Bit INTPOL controls the signal polarity of the INT output: active HIGH or LOW, rising

or falling edge. For level-triggering, bit INTLVL must be made logic 0. By setting

INTLVL to logic 1, an interrupt will generate a pulse of 60 ns (edge-triggering).

Table 22: Status of the chip

VBUS SoftConnect = on SoftConnect = off

On pull-up resistor on DP pull-up resistor on DP is removed;

suspend interrupt is immediately set,

regardless of the D+ and D− signals

Off pull-up resistor on DP is removed;

suspend interrupt is immediately set,

regardless of the D+ and D− signals

pull-up resistor on DP is removed;

suspend interrupt is immediately set,

regardless of the D+ and D− signals

Table 23: Interrupt Conﬁguration register: bit allocation

Bit 76543210

Symbol CDBGMOD[1:0] DDBGMODIN[1:0] DDBGMODOUT[1:0] INTLVL INTPOL

Reset 11111100

Bus reset 111111unchanged unchanged

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 24: Interrupt Conﬁguration register: bit description

Bit Symbol Description

7 to 6 CDBGMOD[1:0] Control 0 Debug Mode: For values, see Table 25

5 to 4 DDBGMODIN[1:0] Data Debug Mode IN: For values, see Table 25

3 to 2 DDBGMODOUT[1:0] Data Debug Mode OUT: For values, see Table 25

1 INTLVL Interrupt Level: Selects signaling mode on output INT

(0 = level; 1 = pulsed). In pulsed mode, an interrupt

produces a 60 ns pulse. Bus reset value: unchanged.

0 INTPOL Interrupt Polarity: Selects signal polarity on output INT

(0 = active LOW; 1 = active HIGH). Bus reset

value: unchanged.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 28 of 66

[1] First NAK: the ﬁrst NAK on an IN or OUT token after a previous ACK response.

9.2.4 OTG register (address: 12h)

The bit allocation of the OTG register is given in Table 26.

Table 25: Debug mode settings

Value CDBGMOD DDBGMODIN DDBGMODOUT

00h interrupt on all ACK and

NAK interrupt on all ACK and

NAK interrupt on all ACK, NYET

and NAK

01h interrupt on all ACK. interrupt on ACK interrupt on ACK and NYET

1Xh interrupt on all ACK and

ﬁrst NAK[1] interrupt on all ACK and

ﬁrst NAK[1] interrupt on all ACK, NYET

and ﬁrst NAK[1]

Table 26: OTG register: bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved DP BSESSVALID INITCOND DISCV VP OTG

Reset --0- -000

Bus reset --0- -000

Access - - R/W R/W R/W R/W R/W R/W

Table 27: OTG register: bit description[1][2][3]

Bit Symbol Description

7 to 6 - reserved

5 DP When set, data-line pulsing is started. The default value of this bit is

logic 0. This bit must be cleared when data-line pulsing is completed.

4 BSESS VALID The device can initiate another VBUS discharge sequence after

data-line pulsing and VBUS pulsing, and before it clears this bit and

detects a session valid.

This bit is latched to logic 1 once VBUS exceeds the B-device session

valid threshold. Once set, it remains at logic 1. To clear this bit, write

logic 1. (The ISP1582 continuously updates this bit to logic 1 when

the B-session is valid. If the B-session is valid after it is cleared, it is

set back to logic 1 by the ISP1582).

0 — It implies that SRP has failed. To proceed to a normal operation,

the device can restart SRP, clear bit OTG or proceed to an error

handling process.

1 — It implies that the B-session is valid. The device clears bit OTG,

goes into normal operation mode, and sets bit SOFTCT (DP pull-up)

in the Mode register. The OTG host has a maximum of 5 s before it

responds to a session request. During this period, the ISP1582 may

request to suspend. Therefore, the device ﬁrmware must wait for

sometime if it wishes to know the SRP result (success—if there is

minimum response from the host within 5 s; failure—if there is no

response from the host within 5 s).

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 29 of 66

[1] No interrupt is designed for OTG. The VBUS interrupt, however, may assert as a side effect during the

VBUS pulsing (see note 2).

[2] When OTG is in progress, the VBUS interrupt may be set because VBUS is charged over VBUS sensing

threshold or the OTG host has turned on the VBUS supply to the device. Even if the VBUS interrupt is

found during SRP, the device should complete data-line pulsing and VBUS pulsing before starting the

B_SESSION_VALID detection.

[3] OTG implementation applies to the device with self-power capability. If the device works in sharing

mode, it should provide a switch circuit to supply power to the ISP1582 core during SRP.

Session Request Protocol (SRP):

The ISP1582 can initiate an SRP. The B-device initiates SRP by data-line pulsing

followed by VBUS pulsing. The A-device can detect either data-line pulsing or VBUS

pulsing.

The ISP1582 can initiate the B-device SRP by performing the following steps:

1. Detect initial conditions: read bit INITCOND of the OTG register.

2. Start data-line pulsing: set bit DP of the OTG register to logic 1.

3. Wait for 5 ms to 10 ms.

4. Stop data-line pulsing: set bit DP of the OTG register to logic 0.

5. Start VBUS pulsing: set bit VP of the OTG register to logic 1.

6. Wait for 10 ms to 20 ms.

7. Stop VBUS pulsing: set bit VP of the OTG register to logic 0.

8. Discharge VBUS for about 30 ms: optional by using bit DISCV of the OTG register.

3 INIT COND Write logic 1 to clear this bit. The device clears this bit, and waits for

more than 2 ms to check the bit status. If it reads logic 0, it means

that VBUS remains lower than 0.8 V, and DP or DM at SE0 during the

elapsed time is cleared. The device can then start a B-device SRP. If

it reads logic 1, it means that the initial condition of an SRP is

violated. So, the device should abort SRP.

The bit is set to logic 1 by the ISP1582 when initial conditions are not

met, and only writing logic 1 clears the bit. (If initial conditions are not

met after this bit has been cleared, it will be set again).

Remark: This implementation does not cover the case if an initial

SRP condition is violated when this bit is read and data-line pulsing is

started.

2 DISCV Set to logic 1 to discharge VBUS. The device discharges VBUS before

starting a new SRP. The discharge can take as long as 30 ms for

VBUS to be charged less than 0.8 V. This bit must be cleared (write

logic 0) before starting a session end detection.

1 VP Set to logic 1 to start VBUS pulsing. This bit must be set for more than

16 ms and must be cleared before 26 ms.

0OTG 1 — Enables the OTG function. The VBUS sensing functionality will be

bypassed.

0 — Normal operation. All OTG control bits will be masked. Status

bits are undeﬁned.

Table 27: OTG register: bit description[1][2][3]

…continued

Bit Symbol Description

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 30 of 66

9. Detect bit BSESSVALID of the OTG register for a successful SRP with bit OTG

disabled.

The B-device must complete both data-line pulsing and VBUS pulsing within 100 ms.

Remark: When disabling, OTG data-line pulsing bit DP and VBUS pulsing bit VP must

be cleared by writing logic 1.

9.2.5 Interrupt Enable register (address: 14h)

This register enables or disables individual interrupt sources. The interrupt for each

endpoint can be individually controlled via the associated bits IEPnRX or IEPnTX,

here n represents the endpoint number. All interrupts can be globally disabled

through bit GLINTENA in the Mode register (see Table 20).

An interrupt is generated when the USB SIE receives or generates an ACK or NAK

on the USB bus. The interrupt generation depends on Debug mode settings of bit

ﬁelds CDBGMOD[1:0], DDBGMODIN[1:0] and DDBGMODOUT[1:0].

All data IN transactions use the Transmit buffers (TX), which are handled by bits

DDBGMODIN. All data OUT transactions go via the Receive buffers (RX), which are

handled by bits DDBGMODOUT. Transactions on control endpoint 0 (IN, OUT and

SETUP) are handled by bits CDBGMOD.

Interrupts caused by events on the USB bus (SOF, Pseudo SOF, suspend, resume,

bus reset, setup and high-speed status) can also be individually controlled. A bus

reset disables all enabled interrupts except bit IEBRST (bus reset), which remains

unchanged.

The Interrupt Enable register consists of 4 bytes. The bit allocation is given in

Table 28.

Table 28: Interrupt Enable register: bit allocation

Bit 31 30 29 28 27 26 25 24

Symbol reserved IEP7TX IEP7RX

Reset ------00

Bus Reset ------00

Access - - - - - - R/W R/W

Bit 23 22 21 20 19 18 17 16

Symbol IEP6TX IEP6RX IEP5TX IEP5RX IEP4TX IEP4RX IEP3TX IEP3RX

Reset 00000000

Bus Reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Bit 15 14 13 12 11 10 9 8

Symbol IEP2TX IEP2RX IEP1TX IEP1RX IEP0TX IEP0RX reserved IEP0SETUP

Reset 000000-0

Bus Reset 000000-0

Access R/W R/W R/W R/W R/W R/W R/W R/W

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 31 of 66

9.3 Data ﬂow registers

9.3.1 Endpoint Index register (address: 2Ch)

The Endpoint Index register selects a target endpoint for register access by the

microcontroller. The register consists of 1 byte, and the bit allocation is shown in

Table 30.

Bit 7 6 5 4 3 2 1 0

Symbol IEVBUS IEDMA IEHS_STA IERESM IESUSP IEPSOF IESOF IEBRST

Reset 00000000

Bus Reset 0000000unchanged

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 29: Interrupt Enable register: bit description

Bit Symbol Description

31 to 26 - reserved

25 EP7TX Logic 1 enables interrupt from the indicated endpoint.

24 EP7RX Logic 1 enables interrupt from the indicated endpoint.

23 EP6TX Logic 1 enables interrupt from the indicated endpoint.

22 EP6RX Logic 1 enables interrupt from the indicated endpoint.

21 EP5TX Logic 1 enables interrupt from the indicated endpoint.

20 EP5RX Logic 1 enables interrupt from the indicated endpoint.

19 EP4TX Logic 1 enables interrupt from the indicated endpoint.

18 EP4RX Logic 1 enables interrupt from the indicated endpoint.

17 EP3TX Logic 1 enables interrupt from the indicated endpoint.

16 EP3RX Logic 1 enables interrupt from the indicated endpoint.

15 EP2TX Logic 1 enables interrupt from the indicated endpoint.

14 EP2RX Logic 1 enables interrupt from the indicated endpoint.

13 EP1TX Logic 1 enables interrupt from the indicated endpoint.

12 IEP1RX Logic 1 enables interrupt from the indicated endpoint.

11 IEP0TX Logic 1 enables interrupt from the control IN endpoint 0.

10 IEP0RX Logic 1 enables interrupt from the control OUT endpoint 0.

9 - reserved

8 IEP0SETUP Logic 1 enables interrupt for the setup data received on endpoint 0.

7 IEVBUS Logic 1 enables interrupt for VBUS sensing.

6 IEDMA Logic 1 enables interrupt on DMA status change detection.

5 IEHS_STA Logic 1 enables interrupt on detection of a high-speed status

change.

4 IERESM Logic 1 enables interrupt on detection of a resume state.

3 IESUSP Logic 1 enables interrupt on detection of a suspend state.

2 IEPSOF Logic 1 enables interrupt on detection of a Pseudo SOF.

1 IESOF Logic 1 enables interrupt on detection of an SOF.

0 IEBRST Logic 1 enables interrupt on detection of a bus reset.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 32 of 66

The following registers are indexed:

•Buffer Length

•Buffer Status

•Control Function

•Data Port

•Endpoint MaxPacketSize

•Endpoint Type.

For example, to access the OUT data buffer of endpoint 1 using the Data Port

Remark: The Endpoint Index register and the DMA Endpoint Index register must not

point to the same endpoint.

Table 30: Endpoint Index register: bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved EP0SETUP ENDPIDX[3:0] DIR

Reset - - 000000

Bus reset - - 000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 31: Endpoint Index register: bit description

Bit Symbol Description

7 to 6 - reserved

5 EP0SETUP Selects the SETUP buffer for endpoint 0.

0 — EP0 data buffer

1 — SETUP buffer.

Must be logic 0 for access to other endpoints than endpoint 0.

4 to 1 ENDPIDX[3:0] Endpoint Index: Selects the target endpoint for register access of

Buffer Length, Control Function, Data Port, Endpoint Type and

MaxPacketSize.

0 DIR Direction bit: Sets the target endpoint as IN or OUT.

0 — target endpoint refers to OUT (RX) FIFO

1 — target endpoint refers to IN (TX) FIFO.

Table 32: Addressing of endpoint 0 buffers

Buffer name EP0SETUP ENDPIDX DIR

SETUP 1 00h 0

Data OUT 0 00h 0

Data IN 0 00h 1

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 33 of 66

9.3.2 Control Function register (address: 28h)

The Control Function register performs the buffer management on endpoints. It

consists of 1 byte, and the bit conﬁguration is given in Table 33. The register bits can

stall, clear or validate any enabled data endpoint. Before accessing this register, the

Endpoint Index register must be written ﬁrst to specify the target endpoint.

9.3.3 Data Port register (address: 20h)

This 2-byte register provides direct access for a microcontroller to the FIFO of the

indexed endpoint. The bit allocation is shown in Table 35.

Table 33: Control Function register: bit allocation

Bit 76543210

Symbol reserved CLBUF VENDP DSEN STATUS STALL

Reset - - -00000

Bus reset - - -00000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 34: Control Function register: bit description

Bit Symbol Description

7 to 5 - reserved

4 CLBUF Clear Buffer: Logic 1 clears the RX buffer of the indexed endpoint; the TX

buffer is not affected. The RX buffer is automatically cleared once the

endpoint is completely read. This bit is set only when it is necessary to

forcefully clear the buffer.

3 VENDP Validate Endpoint: Logic 1 validates the data in the TX FIFO of an IN

endpoint for sending on the next IN token. In general, the endpoint is

automatically validated when its FIFO byte count has reached the

endpoint MaxPacketSize. This bit is set only when it is necessary to

validate the endpoint with the FIFO byte count which is below the

Endpoint MaxPacketSize.

2 DSEN Data Stage Enable: This bit controls the response of the ISP1582 to a

control transfer. When this bit is set, the ISP1582 goes to the data stage;

otherwise, the ISP1582 will NAK the data stage transfer until the ﬁrmware

explicitly responds to the setup command.

1 STATUS Status Acknowledge: Only applicable for control IN/OUT.

This bit controls the generation of ACK or NAK during the status stage of

a SETUP transfer. It is automatically cleared when the status stage is

completed, or when a SETUP token is received. No interrupt signal will be

generated.

0 — Sends NAK

1 — Sends an empty packet following the IN token (host-to-peripheral) or

ACK following the OUT token (peripheral-to-host).

0 STALL Stall Endpoint: Logic 1 stalls the indexed endpoint. This bit is not

applicable for isochronous transfers.

Remark: ‘Stall’ing a data endpoint will confuse the Data Toggle bit about

the stalled endpoint because the internal logic picks up from where it is

stalled. Therefore, the Data Toggle bit must be reset by disabling and

reenabling the corresponding endpoint (by setting bit ENABLE to logic 0

or logic 1 in the Endpoint Type register) to reset the PID.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 34 of 66

Peripheral-to-host (IN endpoint): After each write action, an internal counter is auto

incremented by two to the next location in the TX FIFO. When all bytes have been

written (FIFO byte count = endpoint MaxPacketSize), the buffer is automatically

validated. The data packet will then be sent on the next IN token. When it is

necessary to validate the endpoint whose byte count is less than MaxPacketSize, it

can be done using the Control Function register (bit VENDP).

Host-to-peripheral (OUT endpoint): After each read action, an internal counter is

auto decremented by two to the next location in the RX FIFO. When all bytes have

been read, the buffer contents are automatically cleared. A new data packet can then

be received on the next OUT token. The buffer contents can also be cleared through

the Control Function register (bit CLBUF), when it is necessary to forcefully clear the

contents.

Remark: The buffer can be automatically validated or cleared by using the Buffer

Length register (see Table 37).

9.3.4 Buffer Length register (address: 1Ch)

This register determines the current packet size (DATACOUNT) of the indexed

endpoint FIFO. The bit allocation is given in Table 37.

The Buffer Length register is automatically loaded with the FIFO size, when the

Endpoint MaxPacketSize register is written (see Table 41). A smaller value can be

written when required. After a bus reset, the Buffer Length register is made zero.

IN endpoint: When data transfer is performed in multiples of MaxPacketSize, the

Buffer Length register is not signiﬁcant. This register is useful only when transferring

data that is not a multiple of MaxPacketSize. The following two examples

demonstrate the signiﬁcance of the Buffer Length register.

Table 35: Data Port register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol DATAPORT[15:8]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Bit 76543210

Symbol DATAPORT[7:0]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 36: Data Port register: bit description

Bit Symbol Description

15 to 8 DATAPORT[15:8] data (upper byte)

7 to 0 DATAPORT[7:0] data (lower byte)

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 35 of 66

Example 1: Consider that the transfer size is 512 bytes and the MaxPacketSize is

programmed as 64 bytes, the Buffer Length register need not be ﬁlled. This is

because the transfer size is a multiple of MaxPacketSize, and the MaxPacketSize

packets will be automatically validated because the last packet is also of

MaxPacketSize.

Example 2: Consider that the transfer size is 510 bytes and the MaxPacketSize is

programmed as 64 bytes, the Buffer Length register should be ﬁlled with 62 bytes just

before the MCU writes the last packet of 62 bytes. This ensures that the last packet,

which is a short packet of 62 bytes, is automatically validated.

Use bit VENDP in the Control register if you are not using the Buffer Length register.

This is applicable only to PIO mode access.

OUT endpoint: The DATACOUNT value is automatically initialized to the number of

data bytes sent by the host on each ACK.

Remark: When using a 16-bit microprocessor bus, the last byte of an odd-sized

packet is output as the lower byte (LSByte).

Remark: Buffer Length is valid only after an interrupt is generated for the bulk

endpoint.

9.3.5 Buffer Status register (address: 1Eh)

This register is accessed using index. The endpoint index must ﬁrst be set before

accessing this register for the corresponding endpoint. It reﬂects the status of the

double buffered endpoint FIFO. This register is valid only when the endpoint is

conﬁgured to be a double buffer.

Remark: This register is not applicable to the control endpoint.

Table 39 shows the bit allocation of the Buffer Status register.

Table 37: Buffer Length register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol DATACOUNT[15:8]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Bit 76543210

Symbol DATACOUNT[7:0]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 38: Buffer Length register: bit description

Bit Symbol Description

15 to 0 DATACOUNT[15:0] Determines the current packet size of the indexed endpoint

FIFO.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 36 of 66

9.3.6 Endpoint MaxPacketSize register (address: 04h)

This register determines the maximum packet size for all endpoints except control 0.

The register contains 2 bytes, and the bit allocation is given in Table 41.

Each time the register is written, the Buffer Length registers of all endpoints are

reinitialized to the FFOSZ ﬁeld value. Bits NTRANS control the number of

transactions allowed in a single microframe (for high-speed isochronous and interrupt

endpoints only).

Table 39: Buffer Status register: bit allocation

Bit 76543210

Symbol reserved BUF1 BUF0

Reset ------00

Bus reset ------00

Access ------RR

Table 40: Buffer Status register: bit description

Bit Symbol Description

7 to 2 - reserved

1 to 0 BUF[1:0] 00 — The buffers are not ﬁlled.

01 — One of the buffers is ﬁlled.

10 — One of the buffers is ﬁlled.

11 — Both the buffers are ﬁlled.

Table 41: Endpoint MaxPacketSize register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol reserved NTRANS[1:0] FFOSZ[10:8]

Reset - - -00000

Bus reset - - -00000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Bit 76543210

Symbol FFOSZ[7:0]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 37 of 66

Each programmable FIFO can be independently conﬁgured via its Endpoint

MaxPacketSize register (R/W: 04h), but the total physical size of all enabled

endpoints (IN plus OUT) must not exceed 8192 bytes.

9.3.7 Endpoint Type register (address: 08h)

This register sets the endpoint type of the indexed endpoint: isochronous, bulk or

interrupt. It also serves to enable the endpoint and conﬁgure it for double buffering.

Automatic generation of an empty packet for a zero-length TX buffer can be disabled

using bit NOEMPKT. The register contains 2 bytes, and the bit allocation is shown in

Table 44.

Table 42: Endpoint MaxPacketSize register: bit description

Bit Symbol Description

15 to 13 - reserved

12 to 11 NTRANS[1:0] Number of Transactions. HS mode only.

00 — 1 packet per microframe

01 — 2 packets per microframe

10 — 3 packets per microframe

11 — reserved.

These bits are applicable only for isochronous or interrupt

transactions.

10 to 0 FFOSZ[10:0] FIFO Size: Sets the FIFO size, in bytes, for the indexed endpoint.

Applies to both high-speed and full-speed operations (see

Table 43).

Table 43: Programmable FIFO size

NTRANS[1:0] FFOSZ[10:0] Non-isochronous Isochronous

0h 08h 8 bytes -

0h 10h 16 bytes -

0h 20h 32 bytes -

0h 40h 64 bytes -

0h 80h 128 bytes -

0h 100h 256 bytes -

0h 200h 512 bytes -

2h 400h - 3072 bytes

Table 44: Endpoint Type register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol reserved

Reset --------

Bus reset --------

Access R/W R/W R/W R/W R/W R/W R/W R/W

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 38 of 66

9.4 DMA registers

The Generic DMA (GDMA) transfer can be done by writing the proper opcode in the

DMA Command register. The control bits are given in Table 46.

GDMA read/write (opcode = 00h/01h) for Generic DMA slave mode

Depending on the MODE[1:0] bit set in the DMA conﬁguration register, either the

DACK signal or the DIOR/DIOW signals strobe the data. These signals are driven by

the external DMA controller.

GDMA (slave) mode can operate in either counter mode or EOT-only mode.

In counter mode, bit DIS_XFER_CNT in the DMA Conﬁguration register must be set

to logic 0. The DMA Transfer Counter register must be programmed before any DMA

command is issued. The DMA transfer counter is set by writing from the LSByte to the

MSByte (address: 34h to 37h). The DMA transfer count is internally updated only

after the MSByte has been written. Once the DMA transfer is started, the transfer

counter starts decrementing and on reaching 0, bit DMA_XFER_OK is set and an

Bit 76543210

Symbol reserved NOEMPKT ENABLE DBLBUF ENDPTYP[1:0]

Reset - - -00000

Bus reset - - -00000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 45: Endpoint Type register: bit description

Bit Symbol Description

15 to 5 - reserved

4 NOEMPKT No Empty Packet: Logic 0 causes the ISP1582 to return a null

length packet for the IN token after the DMA IN transfer is

complete. For ATA mode or the IN DMA transfer, which does not

require a null length packet after DMA completion, set to logic 1 to

disable the generation of the null length packet.

3 ENABLE Endpoint Enable: Logic 1 enables the FIFO of the indexed

endpoint. The memory size is allocated as speciﬁed in the

Endpoint MaxPacketSize register. Logic 0 disables the FIFO.

Remark: ‘Stall’ing a data endpoint will confuse the Data Toggle bit

on the stalled endpoint because the internal logic picks up from

where it has stalled. Therefore, the Data Toggle bit must be reset

by disabling and reenabling the corresponding endpoint (by setting

bit ENABLE to logic 0 or logic 1 in the Endpoint Type register) to

reset the PID.

2 DBLBUF Double Buffering: Logic 1 enables double buffering for the

indexed endpoint. Logic 0 disables double buffering.

1 to 0 ENDPTYP[1:0] Endpoint Type: These bits select the endpoint type as follows.

00 — not used

01 — Isochronous

10 — Bulk

11 — Interrupt.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 39 of 66

interrupt is generated by the ISP1582. If the DMA master wishes to terminate the

DMA transfer, it can issue an EOT signal to the ISP1582. This EOT signal overrides

the transfer counter and can terminate the DMA transfer at any time.

In EOT-only mode, DIS_XFER_CNT has to be set to logic 1. Although the DMA

transfer counter can still be programmed, it will not have any effect on the DMA

transfer. The DMA transfer will start once the DMA command is issued. Any of the

following three ways will terminate this DMA transfer:

•Detecting an external EOT

•Detecting an internal EOT (short packet on an OUT token)

•Resetting the DMA.

There are three interrupts programmable to differentiate the method of DMA

termination: bits INT_EOT, EXT_EOT and DMA_XFER_OK in the DMA Interrupt

Reason register. For details, see Table 58.

Remark: The DMA bus defaults to three-state, until a DMA command is executed. All

the other control signals are not three-state.

9.4.1 DMA Command register (address: 30h)

The DMA Command register is a 1-byte register (for bit allocation, see Table 47) that

initiates all DMA transfer activity on the DMA controller. The register is write-only:

reading it will return FFh.

Remark: The DMA bus will be in three-state until a DMA command is executed.

Table 46: Control bits for GDMA read/write (opcode = 00h/01h)

Control bits Description Reference

DMA Conﬁguration register

MODE[1:0] Determines the active read/write data strobe signals. Table 52

WIDTH Selects the DMA bus width: 8 or 16 bits.

DIS_XFER_CNT Disables the use of the DMA Transfer Counter.

DMA Hardware register

EOT_POL Selects the polarity of the EOT signal. Table 54

ENDIAN[1:0] Determines whether the data is to be byte swapped or

normal. Applicable only in 16-bit mode.

ACK_POL,

DREQ_POL,

WRITE_POL,

READ_POL

Select the polarity of the DMA handshake signals.

Table 47: DMA Command register: bit allocation

Bit 76543210

Symbol DMA_CMD[7:0]

Reset 11111111

Bus reset 11111111

Access WWWWWWWW

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 40 of 66

9.4.2 DMA Transfer Counter register (address: 34h)

This 4-byte register sets up the total byte count for a DMA transfer (DMACR). It

indicates the remaining number of bytes left for transfer. The bit allocation is given in

Table 50.

For IN endpoint — As there is a FIFO in the ISP1582 DMA controller, some data

may remain in the FIFO during the DMA transfer. The maximum FIFO size is 8 bytes,

and the maximum delay time for the data to be shifted to endpoint buffer is 60 ns.

For OUT endpoint — Data will not be cleared for the endpoint buffer until all the data

has been read from the DMA FIFO.

If the DMA counter is disabled in the DMA transfer, it will still decrement and rollover

when it reaches zero.

Table 48: DMA Command register: bit description

Bit Symbol Description

7 to 0 DMA_CMD[7:0] DMA command code; see Table 49.

Table 49: DMA commands

Code Name Description

00h GDMA Read Generic DMA IN token transfer (slave mode only): Data is transferred from the external

DMA bus to the internal buffer. Strobe: DIOW by external DMA controller.

01h GDMA Write Generic DMA OUT token transfer (slave mode only): Data is transferred from the internal

buffer to the external DMA bus. Strobe: DIOR by external DMA controller.

02h to 0Dh - reserved

0Eh Validate Buffer Validate Buffer (for debugging only): Request from the microcontroller to validate the

endpoint buffer following a DMA to USB data transfer.

0Fh Clear Buffer Clear Buffer: Request from the microcontroller to clear the endpoint buffer after a USB to

DMA data transfer.

10h - reserved

11h Reset DMA Reset DMA: Initializes the DMA core to its power-on reset state.

Remark: When the DMA core is reset during the Reset DMA command, the DREQ, DACK,

DIOW and DIOR handshake pins will be temporarily asserted. This can confuse the external

DMA controller. To prevent this, start the external DMA controller only after the DMA reset.

12h - reserved

13h GDMA Stop GDMA stop: This command stops the GDMA data transfer. Any data in the OUT endpoint

that is not transferred by the DMA will remain in the buffer. The FIFO data for the IN endpoint

will be written to the endpoint buffer. An interrupt bit will be set to indicate the completion of

the DMA Stop command.

14h to FFh - reserved

Table 50: DMA Transfer Counter register: bit allocation

Bit 31 30 29 28 27 26 25 24

Symbol DMACR4 = DMACR[31:24]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 41 of 66

9.4.3 DMA Conﬁguration register (address: 38h)

This register deﬁnes the DMA conﬁguration for GDMA mode. The DMA Conﬁguration

Bit 23 22 21 20 19 18 17 16

Symbol DMACR3 = DMACR[23:16]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Bit 15 14 13 12 11 10 9 8

Symbol DMACR2 = DMACR[15:8]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Bit 76543210

Symbol DMACR1 = DMACR[7:0]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 51: DMA Transfer Counter register: bit description

Bit Symbol Description

31 to 24 DMACR4, DMACR[31:24] DMA transfer counter byte 4 (MSB)

23 to 16 DMACR3, DMACR[23:16] DMA transfer counter byte 3

15 to 8 DMACR2, DMACR[15:8] DMA transfer counter byte 2

7 to 0 DMACR1, DMACR[7:0] DMA transfer counter byte 1 (LSB)

Table 52: DMA Conﬁguration register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol reserved

Reset 00000000

Bus Reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Bit 76543210

Symbol DIS_

XFER_CNT reserved MODE[1:0] reserved WIDTH

Reset 00000001

Bus Reset 00000001

Access R/W R/W R/W R/W R/W R/W R/W R/W

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 42 of 66

[1] The DREQ pin will only be driven only after you perform a write access to the DMA Conﬁguration

9.4.4 DMA Hardware register (address: 3Ch)

The DMA Hardware register consists of 1 byte. The bit allocation is shown in

Table 54.

This register determines the polarity of the bus control signals (EOT, DACK, DREQ,

DIOR and DIOW) and DMA mode (master or slave). It also controls whether the

upper and lower parts of the data bus are swapped (bits ENDIAN[1:0]) for GDMA

(slave) mode.

Table 53: DMA Conﬁguration register: bit description[1]

Bit Symbol Description

15 to 8 - reserved

7 DIS_XFER_CNT Logic 1 disables the DMA Transfer Counter (see Table 50). The

transfer counter can be disabled only in GDMA (slave) mode.

6 to 4 - reserved

3 to 2 MODE[1:0] These bits only affect the GDMA slave handshake signals.

00 — DIOW slave strobes data from the DMA bus into the

ISP1582; DIOR slave puts data from the ISP1582 on the DMA

bus

01 — DACK slave strobes data from the DMA bus into the

ISP1582; DIOR slave puts data from the ISP1582 on the DMA

bus

10 — DACK slave strobes data from the DMA bus into the

ISP1582 and also puts data from the ISP1582 on the DMA bus.

(This mode is applicable only to the 16-bit DMA; this mode

cannot be used for the 8-bit DMA.)

11 — reserved.

1 - reserved

0 WIDTH This bit selects the DMA bus width for the GDMA slave.

0 — 8-bit data bus

1 — 16-bit data bus.

Table 54: DMA Hardware register: bit allocation

Bit 76543210

Symbol ENDIAN[1:0] EOT_POL reserved ACK_POL DREQ_

POL WRITE_

POL READ_

POL

Reset 00000100

Bus reset 00000100

Access R/W R/W R/W R/W R/W R/W R/W R/W

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 43 of 66

9.4.5 DMA Interrupt Reason register (address: 50h)

This 2-byte register shows the source(s) of DMA interrupt. Each bit is refreshed after

a DMA command has been executed. An interrupt source is cleared by writing logic 1

to the corresponding bit. When reading, AND the value of the bits in this register with

the value of the corresponding bits in the DMA Interrupt Enable register.

The bit allocation is given in Table 56.

Table 55: DMA Hardware register: bit description

Bit Symbol Description

7 to 6 ENDIAN[1:0] These bits determine whether the data bus is swapped between the

internal RAM and the DMA bus. This only applies for GDMA (slave)

mode.

00 — Normal data representation

16-bit bus: MSB on DATA[15:8], LSB on DATA[7:0]

01 — Swapped data representation

16-bit bus: MSB on DATA[7:0], LSB on DATA[15:8]

10 — reserved

11 — reserved.

Remark: While operating with the 8-bit data bus, bits ENDIAN[1:0]

should be always set to logic 00.

5 EOT_POL Selects the polarity of the End-Of-Transfer input; used in GDMA

(slave) mode only.

0 — EOT is active LOW

1 — EOT is active HIGH.

4 - reserved; must be set to logic 0.

3 ACK_POL Selects the DMA acknowledgment polarity.

0 — DACK is active LOW

1 — DACK is active HIGH.

2 DREQ_POL Selects the DMA request polarity.

0 — DREQ is active LOW

1 — DREQ is active HIGH.

1 WRITE_POL Selects the DIOW strobe polarity.

0 — DIOW is active LOW

1 — DIOW is active HIGH.

0 READ_POL Selects the DIOR strobe polarity.

0 — DIOR is active LOW

1 — DIOR is active HIGH.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 44 of 66

Table 59 shows the status of the bits in the DMA Interrupt Reason register when the

corresponding bits in the Interrupt register is set.

Table 56: DMA Interrupt Reason register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol TEST3 reserved GDMA_

STOP EXT_EOT INT_EOT reserved DMA_

XFER_OK

Reset ---000-0

Bus reset ---000-0

Access R R R R/W R/W R/W R/W R/W

Bit 76543210

Symbol reserved

Reset --------

Bus reset --------

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 57: DMA Interrupt Reason register: bit description

Bit Symbol Description

15 TEST3 This bit is set when the DMA transfer for a packet (OUT transfer)

terminates before the whole packet has been transferred. This

bit is a status bit, and the corresponding mask bit of this register

is always logic 0. Writing any value other than logic 0 has no

effect.

14 to 13 - reserved

12 GDMA_STOP When the GDMA_STOP command is issued to the DMA

Command registers, it means the DMA transfer has

successfully terminated.

11 EXT_EOT Logic 1 indicates that an external EOT is detected. This is

applicable only in GDMA (slave) mode.

10 INT_EOT Logic 1 indicates that an internal EOT is detected; see Table 58.

9 - reserved

8 DMA_XFER_OK Logic 1 indicates that the DMA transfer has been completed

(DMA Transfer Counter has become zero). This bit is only used

in GDMA (slave) mode.

7 to 0 - reserved

Table 58: Internal EOT-functional relation with bit DMA_XFER_OK

INT_EOT DMA_XFER_OK Description

1 0 During the DMA transfer, there is a premature termination

with short packet.

1 1 DMA transfer is completed with short packet and the DMA

transfer counter has reached 0.

0 1 DMA transfer is completed without any short packet and the

DMA transfer counter has reached 0.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 45 of 66

[1] 1 indicates that the bit is set and 0 indicates that the bit is not set. A bit is set when the corresponding

EOT condition is met. For example; EXT_EOT is set if external EOT conditions are met (pin EOT

active), regardless of other EOT conditions. If multiple EOT conditions are met, the corresponding

interrupt bits are set.

[2] If both EXT_EOT and DMA_XFER_OK conditions are met in DMA for an IN endpoint, the EXT_EOT

interrupt is not set.

[3] The value of INT_EOT may not be accurate if an external or internal transfer counter is programmed

with a value that is lower than the transfer that the host requests. To terminate an OUT transfer with

INT_EOT, the external or internal DMA counter should be programmed as a multiple of the full-packet

length of the DMA endpoint. When a short packet is successfully transferred by DMA, INT_EOT is set.

9.4.6 DMA Interrupt Enable register (address: 54h)

This 2-byte register controls the interrupt generation of the source bits in the DMA

Interrupt Reason register. The bit allocation is given in Table 60. The bit description is

given in Table 57.

Logic 1 enables the interrupt generation. After a bus reset, interrupt generation is

disabled, with the values turning to logic 0.

9.4.7 DMA Endpoint register (address: 58h)

This 1-byte register selects a USB endpoint FIFO as a source or destination for DMA

transfers. The bit allocation is given in Table 61.

Table 59: Status of the bits in the DMA Interrupt Reason register[1][2]

Status EXT_EOT INT_EOT DMA_XFER_OK

Counter enabled Counter disabled

IN full 1 0 1 0

IN short 1 0 1 0

OUT full 1 0 1 0

OUT short 1 1[3] 10

Table 60: DMA Interrupt Enable register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol TEST4 reserved IE_GDMA_

STOP IE_EXT_

EOT IE_INT_

EOT reserved IE_DMA_

XFER_OK

Reset - - -00000

Bus reset - - -00000

Access R - - R/W R/W R/W R/W R/W

Bit 76543210

Symbol reserved

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 61: DMA Endpoint register: bit allocation

Bit 76543210

Symbol reserved EPIDX[2:0] DMADIR

Reset ----0000

Bus reset ----0000

Access ----R/WR/WR/WR/W

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 46 of 66

The DMA Endpoint register must not reference the endpoint that is indexed by the

Endpoint Index register (2Ch) at any time. Doing so would result in data corruption.

Therefore, if the DMA Endpoint register is unused, point it to an unused endpoint. If

the DMA Endpoint register, however, is pointed to an active endpoint, the ﬁrmware

must not reference the same endpoint on the Endpoint Index register.

9.4.8 DMA Burst Counter register (address: 64h)

Table 63 shows the bit allocation of the register.

9.5 General registers

9.5.1 Interrupt register (address: 18h)

The Interrupt register consists of 4 bytes. The bit allocation is given in Table 65.

Table 62: DMA Endpoint register: bit description

Bit Symbol Description

7 to 4 - reserved

3 to 1 EPIDX[2:0] selects the indicated endpoint for DMA access

0 DMADIR 0 — Selects the RX/OUT FIFO for DMA read transfers

1 — Selects the TX/IN FIFO for DMA write transfers.

Table 63: DMA Burst Counter register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol reserved BURSTCOUNTER[12:8]

Reset - - -00000

Bus reset - - -00000

Access - - - R/W R/W R/W R/W R/W

Bit 76543210

Symbol BURSTCOUNTER[7:0]

Reset 00000010

Bus reset 00000010

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 64: DMA Burst Counter register: bit description

Bit Symbol Description

15 to 13 - reserved

12 to 0 BURSTCOUNTER[12:0] This registerdeﬁnes the burst length. The counter must

be programmed to be a multiple of two in 16-bit mode.

The value of the burst counter should be programmed

such that the buffer counter is a factor of the burst

counter.

For IN endpoint — When the burst counter equals 2,

in GDMA mode, DREQ will drop at every DMA read or

write cycle.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 47 of 66

When a bit is set in the Interrupt register, it indicates that the hardware condition for

an interrupt has occurred. When the Interrupt register content is nonzero, the INT

output will be asserted corresponding to the Interrupt Enable register. On detecting

the interrupt, the external microprocessor must read the Interrupt register and mask it

with the corresponding bits in the Interrupt Enable register to determine the source of

the interrupt.

Each endpoint buffer has a dedicated interrupt bit (EPnTX, EPnRX). In addition,

various bus states can generate an interrupt: resume, suspend, pseudo SOF, SOF

and bus reset. The DMA controller only has one interrupt bit: the source for a DMA

interrupt is shown in the DMA Interrupt Reason register.

Each interrupt bit can be individually cleared by writing logic 1. The DMA Interrupt bit

can be cleared by writing logic 1 to the related interrupt source bit in the DMA

Interrupt Reason register and writing logic 1 to the DMA bit of the Interrupt register.

Table 65: Interrupt register: bit allocation

Bit 31 30 29 28 27 26 25 24

Symbol reserved EP7TX EP7RX

Reset -----000

Bus reset -----000

Access -----R/WR/WR/W

Bit 23 22 21 20 19 18 17 16

Symbol EP6TX EP6RX EP5TX EP5RX EP4TX EP4RX EP3TX EP3RX

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Bit 15 14 13 12 11 10 9 8

Symbol EP2TX EP2RX EP1TX EP1RX EP0TX EP0RX reserved EP0SETUP

Reset 000000-0

Bus reset 000000-0

Access R/W R/W R/W R/W R/W R/W - R/W

Bit 76543210

Symbol VBUS DMA HS_STAT RESUME SUSP PSOF SOF BRESET

Reset 00000000

Bus reset 0000000unchanged

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 66: Interrupt register: bit description

Bit Symbol Description

31 to 26 - reserved

25 EP7TX Logic 1 indicates the endpoint 7 TX buffer as interrupt source.

24 EP7RX Logic 1 indicates the endpoint 7 RX buffer as interrupt source.

23 EP6TX Logic 1 indicates the endpoint 6 TX buffer as interrupt source.

22 EP6RX Logic 1 indicates the endpoint 6 RX buffer as interrupt source.

21 EP5TX Logic 1 indicates the endpoint 5 TX buffer as interrupt source.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 48 of 66

9.5.2 Chip ID register (address: 70h)

This read-only register contains the chip identiﬁcation and the hardware version

numbers. The ﬁrmware should check this information to determine the functions and

features supported. The register contains 3 bytes, and the bit allocation is shown in

Table 67.

20 EP5RX Logic 1 indicates the endpoint 5 RX buffer as interrupt source.

19 EP4TX Logic 1 indicates the endpoint 4 TX buffer as interrupt source.

18 EP4RX Logic 1 indicates the endpoint 4 RX buffer as interrupt source.

17 EP3TX Logic 1 indicates the endpoint 3 TX buffer as interrupt source.

16 EP3RX Logic 1 indicates the endpoint 3 RX buffer as interrupt source.

15 EP2TX Logic 1 indicates the endpoint 2 TX buffer as interrupt source.

14 EP2RX Logic 1 indicates the endpoint 2 RX buffer as interrupt source.

13 EP1TX Logic 1 indicates the endpoint 1 TX buffer as interrupt source.

12 EP1RX Logic 1 indicates the endpoint 1 RX buffer as interrupt source.

11 EP0TX Logic 1 indicates the endpoint 0 data TX buffer as interrupt source.

10 EP0RX Logic 1 indicates the endpoint 0 data RX buffer as interrupt source.

9 - reserved

8 EP0SETUP Logic 1 indicates that a SETUP token was received on endpoint 0.

7 VBUS Logic 1 indicates VBUS is turned on.

6 DMA DMA status: Logic 1 indicates a change in the DMA Status

5 HS_STAT High speed status: Logic 1 indicates a change from full-speed to

high-speed mode (HS connection). This bit is not set, when the

system goes into full-speed suspend.

4 RESUME Resume status: Logic 1 indicates that a status change from

suspend to resume (active) was detected.

3 SUSP Suspend status: Logic 1 indicates that a status change from

active to suspend was detected on the bus.

2 PSOF Pseudo SOF interrupt: Logic 1 indicates that a pseudo SOF or

µSOF was received. Pseudo SOF is an internally generated clock

signal (full-speed: 1 ms period, high-speed: 125 µs period)

synchronized to the USB bus SOF or µSOF.

1 SOF SOF interrupt: Logic 1 indicates that a SOF or µSOF was

received.

0 BRESET Bus reset: Logic 1 indicates that a USB bus reset was detected.

When bit OTG in the OTG register is set, BRESET will not be set,

instead, this interrupt bit will report SE0 on DP and DM for 2 ms.

Table 66: Interrupt register: bit description

…continued

Bit Symbol Description

Table 67: Chip ID register: bit allocation

Bit 23 22 21 20 19 18 17 16

Symbol CHIPID[15:8]

Reset 00010101

Bus reset 00010101

Access RRRRRRRR

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 49 of 66

9.5.3 Frame Number register (address: 74h)

This read-only register contains the frame number of the last successfully received

Start-Of-Frame (SOF). The register contains 2 bytes, and the bit allocation is given in

Table 69. In case of 8-bit access, the register content is returned lower byte ﬁrst.

9.5.4 Scratch register (address: 78h)

This 16-bit register can be used by the ﬁrmware to save and restore information. For

example, the device status before it enters the suspend state. The bit allocation is

given in Table 71.

Bit 15 14 13 12 11 10 9 8

Symbol CHIPID[7:0]

Reset 10000010

Bus reset 10000010

Access RRRRRRRR

Bit 76543210

Symbol VERSION[7:0]

Reset 00110000

Bus reset 00110000

Access RRRRRRRR

Table 68: Chip ID register: bit description

Bit Symbol Description

23 to 16 CHIPID[15:8] chip ID: lower byte (15h)

15 to 8 CHIPID[7:0] chip ID: upper byte (82h)

7 to 0 VERSION[7:0] version number (30h)

Table 69: Frame Number register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol reserved MICROSOF[2:0] SOFR[10:8]

Power Reset - -000000

Bus Reset - -000000

Access RRRRRRRR

Bit 76543210

Symbol SOFR[7:0]

Power Reset 00000000

Bus Reset 00000000

Access RRRRRRRR

Table 70: Frame Number register: bit description

Bit Symbol Description

15 to 14 - reserved

13 to 11 MICROSOF[2:0] microframe number

10 to 0 SOFR[10:0] frame number

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 50 of 66

9.5.5 Unlock Device register (address: 7Ch)

To protect the registers from getting corrupted when the ISP1582 goes into suspend,

the write operation is disabled if bit PWRON in the Mode register is set to logic 0. In

this case, when the chip resumes, the Unlock Device command must be ﬁrst issued

to this register before attempting to write to the rest of the registers. This is done by

writing unlock code (AA37h) to this register.

The bit allocation of the Unlock Device register is given in Table 73.

When bit PWRON in the Mode register is logic 1, the chip is powered. In such a case,

you do not need to issue the Unlock command because the microprocessor is

powered and therefore, the RD_N, WR_N and CS_N signals maintain their states.

Table 71: Scratch register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol SFIRH[7:0]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Bit 76543210

Symbol SFIRL[7:0]

Reset 00000000

Bus reset 00000000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 72: Scratch register: bit description

Bit Symbol Description

15 to 8 SFIRH[7:0] Scratch ﬁrmware information register (higher byte)

7 to 0 SFIRL[7:0] Scratch ﬁrmware information register (lower byte)

Table 73: Unlock Device register: bit allocation

Bit 15 14 13 12 11 10 9 8

Symbol ULCODE[15:8] = AAh

Reset not applicable

Bus reset not applicable

Access WWWWWWWW

Bit 76543210

Symbol ULCODE[7:0] = 37h

Reset not applicable

Bus reset not applicable

Access WWWWWWWW

Table 74: Unlock Device register: bit description

Bit Symbol Description

15 to 0 ULCODE[15:0] Writing data AA37h unlocks the internal registers and FIFOs

for writing, following a resume.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 51 of 66

When bit PWRON is logic 0, the RD_N, WR_N and CS_N signals are ﬂoating

because the microprocessor is not powered. To protect the ISP1582 registers from

being corrupted during suspend, register write is locked when the chip goes into

suspend. Therefore, you need to issue the Unlock command to unlock the ISP1582

registers.

9.5.6 Test Mode register (address: 84h)

This 1-byte register allows the ﬁrmware to set pins DP and DM to predetermined

states for testing purposes. The bit allocation is given in Table 75.

Remark: Only one bit can be set to logic 1 at a time. This must be implemented for

the Hi-Speed USB logo compliance testing.

[1] Either FORCEHS or FORCEFS should be set at a time.

[2] Of the four bits (PRBS, KSTATE, JSTATE and SE0_NAK), only one bit should be set at a time.

Table 75: Test Mode register: bit allocation

Bit 76543210

Symbol FORCEHS reserved FORCEFS PRBS KSTATE JSTATE SE0_NAK

Reset 0- -00000

Bus reset 0- -00000

Access R/W R/W R/W R/W R/W R/W R/W R/W

Table 76: Test Mode register: bit description

Bit Symbol Description

7 FORCEHS logic 1[1] forces the hardware to high-speed mode only and

disables the chirp detection logic.

6 to 5 - reserved.

4 FORCEFS logic 1[1] forces the physical layer to full-speed mode only and

disables the chirp detection logic.

3 PRBS logic 1[2] sets pins DP and DM to toggle in a predetermined

random pattern.

2 KSTATE writing logic 1[2] sets pins DP and DM to the K state.

1 JSTATE writing logic 1[2] sets pins DP and DM to the J state.

0 SE0_NAK writing logic 1[2] sets pins DP and DM to a high-speed quiescent

state. The device only responds to a valid high-speed IN token

with a NAK.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 52 of 66

10. Limiting values

[1] The maximum value for 5 V tolerant pins is 6 V.

11. Recommended operating conditions

Table 77: Absolute maximum ratings

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VCC supply voltage −0.5 +4.6 V

VCC(I/O) I/O pad supply voltage −0.5 +4.6 V

VIinput voltage [1] −0.5 VCC + 0.5 V

Ilu latch-up current VI< 0 or VI>V

CC - 100 mA

Vesd electrostatic discharge voltage ILI <1µA−2000 +2000 V

Tstg storage temperature −40 +125 °C

Table 78: Recommended operating conditions

Symbol Parameter Conditions Min Max Unit

VCC supply voltage 3.0 3.6 V

VCC(I/O) I/O pad supply voltage VCC VCC V

VIinput voltage range VCC = 3.3 V 0 5.5 V

VI(AI/O) input voltage on analog I/O pins

DP and DM 0 3.6 V

VO(pu) open-drain output pull-up voltage 0 VCC V

Tamb ambient temperature −40 +85 °C

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 53 of 66

12. Static characteristics

[1] This value is applicable to transistor input only. The value will be different if internal pull-up or pull-down resistors are used.

Table 79: Static characteristics; supply pins

= 3.3 V

0.3 V; V

GND

=0V; T

amb

−

Cto+85

C; typical values at T

amb

=25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Supply voltage

VCC supply voltage 3.0 3.3 3.6 V

ICC operating supply current VCC = 3.3 V

high-speed - 45 60 mA

full-speed - 17 25 mA

ICC(susp) suspend supply current VCC = 3.3 V - 160 - µA

I/O pad supply voltage

VCC(I/O) I/O pad supply voltage VCC VCC VCC V

ICC(I/O) operating supply current VCC(I/O) = 3.3 V

high-speed - 430 500 µA

full-speed - 180 120 µA

ICC(I/O)(susp) suspend supply current VCC(I/O) = 3.3 V - 5 10 µA

Regulated supply voltage

VCC(1V8) regulated supply voltage with voltage

converter 1.65 1.8 1.95 V

Table 80: Static characteristics: digital pins

CC(I/O)

; V

GND

=0V; T

amb

−

C to +85

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Input levels

VIL LOW-level input voltage - - 0.3VCC(I/O) V

VIH HIGH-level input voltage 0.7VCC(I/O) -- V

Output levels

VOL LOW-level output voltage IOL = rated drive - - 0.15VCC(I/O) V

VOH HIGH-level output voltage IOH = rated drive 0.8VCC(I/O) -- V

Leakage current

ILI input leakage current [1] −5- +5 µA

Table 81: Static characteristics: OTG detection

CC(I/O)

; V

GND

=0V; T

amb

−

C to +85

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Charging and discharging resistor

RPD discharging resistor 684.8 843.5 1032 Ω

RPU charging resistor 551.9 666.7 780.6 Ω

Comparator levels

VBVALID VBUS valid detection VCC(I/O) = 3.3 V ±0.3 V 2.0 - 4.0 V

VSESEND VBUS B-session end detection VCC(I/O) = 3.3 V ±0.3 V 0.2 - 0.8 V

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 54 of 66

[1] Pin DP is the USB positive data pin and pin DM is the USB negative data pin.

13. Dynamic characteristics

Table 82: Static characteristics: analog I/O pins DP and DM[1]

= 3.3 V

0.3 V; V

GND

=0V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Input levels

VDI differential input sensitivity |VI(DP) −VI(DM)|0.2 - - V

VCM differential common mode voltage includes VDI range 0.8 - 2.5 V

VSE single-ended receiver threshold 0.8 2.0 V

VIL LOW-level input voltage - - 0.8 V

VIH HIGH-level input voltage 2.0 - - V

Schmitt-trigger inputs

Vth(LH) positive-going threshold voltage 1.4 - 1.9 V

Vth(HL) negative-going threshold voltage 0.9 - 1.5 V

Vhys hysteresis voltage 0.4 - 0.7 V

Output levels

VOL LOW-level output voltage RL= 1.5 kΩ to 3.6 V - - 0.4 V

VOH HIGH-level output voltage RL=15kΩ to GND 2.8 - 3.6 V

Leakage current

ILZ OFF-state leakage current 0 < VI< 3.3 V −10 - +10 µA

Capacitance

CIN transceiver capacitance pin to GND - - 10 pF

Resistance

ZDRV driver output impedance steady-state drive 40.5 - 49.5 Ω

ZINP input impedance 10 - - MΩ

Table 83: Dynamic characteristics

= 3.3 V

0.3 V; V

GND

=0V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Reset

tW(RESET_N) pulse width on pin RESET_N crystal oscillator running 500 - - µs

Crystal oscillator

fXTAL crystal frequency - 12 - MHz

RSseries resistance - - 100 Ω

CLload capacitance - 18 - pF

External clock input

VIN input voltage 1.65 1.8 1.95 V

tJexternal clock jitter - - 500 ps

δclock duty cycle 45 50 55 %

tr, tfrise time and fall time - - 3 ns

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 55 of 66

[1] Excluding the ﬁrst transition from the idle state.

[2] Characterized only, not tested. Limits guaranteed by design.

Table 84: Dynamic characteristics: analog I/O pins DP and DM

= 3.3 V

0.3 V; V

GND

=0V; T

amb

−

Cto+85

C; C

= 50 pF; R

= 1.5 k

Ω

on DP to V

TERM

; test circuit of

Figure 25; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Driver characteristics

Full-speed mode

tFR rise time CL=50pF;

10 % to 90 % of |VOH −VOL|4 - 20 ns

tFF fall time CL=50pF;

90 % to 10 % of |VOH −VOL|4 - 20 ns

FRFM differential rise time and fall time

matching (tFR/tFF)[1] 90 - 111.11 %

VCRS output signal crossover voltage [1][2] 1.3 - 2.0 V

High-speed mode

tHSR high-speed differential rise time with captive cable 500 - - ps

tHSF high-speed differential fall time with captive cable 500 - - ps

Data source timing

Full-speed mode

tFEOPT source EOP width see Figure 16 [2] 160 - 175 ns

tFDEOP source differential data-to-EOP

transition skew see Figure 16 [2] −2 - +5 ns

Receiver timing

Full-speed mode

tJR1 receiver data jitter tolerance to

next transition see Figure 17 [2] −18.5 - +18.5 ns

tJR2 receiver data jitter tolerance for

paired transitions see Figure 17 [2] −9 - +9 ns

tFEOPR receiver SE0 width accepted as EOP; see Figure 16 [2] 82--ns

tFST width of SE0 during differential

transition rejected as EOP; see Figure 18 [2] --14ns

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 56 of 66

TPERIOD is the bit duration corresponding with the USB data rate.

Full-speed timing symbols have a subscript preﬁx ‘F’, low-speed timing symbols have a preﬁx 'L'.

Fig 16. Source differential data-to-EOP transition skew and EOP width.

mgr776

PERIOD

differential

data lines

crossover point

differential data to

SE0/ EOP skew

N × T

PERIOD

+ t

DEOP

source EOP width: t

EOPT

receiver EOP width: t

EOPR

crossover point

extended

+3.3 V

0 V

TPERIOD is the bit duration corresponding with the USB data rate.

Fig 17. Receiver differential data jitter.

mgr871

PERIOD

differential

data lines

+3.3 V

0 V t

JR1

JR2

consecutive

transitions

N × T

PERIOD

+ t

JR1

paired

transitions

N × T

PERIOD

+ t

JR2

Fig 18. Receiver SE0 width tolerance.

mgr872

differential

data lines

+3.3 V

0 V

FST

IH(min)

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 57 of 66

13.1 Register access timing

Table 85: Register access timing parameters: separate address and data buses

CC(I/O)

= 3.3 V; V

GND

=0V; T

amb

−

Cto+85

Symbol Parameter Min Max Unit

Reading

tRLRH RD_N LOW pulse width >tRLDV -ns

tAVRL address set-up time before RD_N LOW 0 - ns

tRHAX address hold time after RD_N HIGH 0 - ns

tRLDV RD_N LOW to data valid delay - 26 ns

tRHDZ RD_N HIGH to data outputs three-state delay 0 15 ns

tRHSH RD_N HIGH to CS_N HIGH delay 0 - ns

tSLRL CS_N LOW to RD_N LOW delay 2 - ns

Writing

tWLWH WR_N LOW pulse width 15 - ns

tAVWL address set-up time before WR_N LOW 0 - ns

tWHAX address hold time after WR_N HIGH 0 - ns

tDVWH data set-up time before WR_N HIGH 11 - ns

tWHDZ data hold time after WR_N HIGH 5 - ns

tWHSH WR_N HIGH to CS_N HIGH delay 0 - ns

tSLWL CS_N LOW to WR_N LOW delay 2 - ns

General

Tcy(RW) read/write cycle time 50 - ns

Fig 19. Register access timing: separate address and data buses.

(write) DATA[15:0]

(read) DATA[15:0]

004aaa276

A[7:0]

tWHSH

tAVWL

tDVWH

tRHDZ

tAVRL

Tcy(RW)

tWHAX

tRHAX

tRLDV

tWHDZ

WR_N

CS_N

RD_N

tRHSH

tRLRH

tWLWH

tSLWL

tSLRL

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 58 of 66

13.2 DMA timing

Table 86: GDMA (slave) mode timing parameters

CC(I/O)

= 3.3 V; V

GND

=0V; T

amb

−

Cto+85

Symbol Parameter Min Max Unit

Tcy1 read/write cycle time 75 - ns

tsu1 DREQ set-up time before ﬁrst DACK on 10 - ns

td1 DREQ on delay after last strobe off 33.33 - ns

th1 DREQ hold time after last strobe on 0 53 ns

tw1 DIOR/DIOW pulse width 39 600 ns

tw2 DIOR/DIOW recovery time 36 - ns

td2 read data valid delay after strobe on - 20 ns

th2 read data hold time after strobe off - 5 ns

th3 write data hold time after strobe off 1 - ns

tsu2 write data set-up time before strobe off 10 - ns

tsu3 DACK set-up time before DIOR/DIOW assertion 0 - ns

ta1 DACK deassertion after DIOR/DIOW deassertion 0 30 ns

DREQ is continuously asserted until the last transfer is done or the FIFO is full.

Data strobes: DIOR (read) and DIOW (write).

(1) Programmable polarity: shown as active LOW.

(2) Programmable polarity: shown as active HIGH.

Fig 20. GDMA (slave) mode timing (bits MODE[1:0] = 00).

th1

tw1

tsu1

td1

tsu2

td2 th2

Tcy1

(write) DATA[15:0]

(read) DATA[15:0]

DREQ (2)

DACK(1)

DIOR/DIOW(1)

MGT500

tsu3

tw2 ta1

th3

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 59 of 66

DREQ is asserted for every transfer.

Data strobes: DIOR (read) and DACK (write).

(1) Programmable polarity: shown as active LOW.

(2) Programmable polarity: shown as active HIGH.

Fig 21. GDMA (slave) mode timing (bits MODE[1:0] = 01).

td1

tw1

tsu1 th1

tsu2

td2

th2

Tcy1

(write) DATA[15:0]

(read) DATA[15:0]

DREQ (2)

DACK(1)

DIOR/DIOW(1)

MGT502

tsu3

ta1

th3

DREQ is continuously asserted until the last transfer is done or the FIFO is full.

Data strobe: DACK (read/write).

(1) Programmable polarity: shown as active LOW.

(2) Programmable polarity: shown as active HIGH.

Fig 22. GDMA (slave) mode timing (bits MODE[1:0] = 10).

th1

tw1

tsu1

td1

tsu2

td2

th2

Tcy1

(write) DATA[15:0]

(read) DATA[15:0]

DREQ (2)

HIGH

DACK(1)

DIOR/DIOW(1)

MGT501

tw2

th3

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 60 of 66

14. Application information

15. Test information

The dynamic characteristics of the analog I/O ports DP and DM were determined

using the circuit shown in Figure 25.

(1) Programmable polarity: shown as active LOW.

Remark: EOT should be valid for 36 ns (minimum) when RD_N/WR_N is active.

Fig 23. EOT timing in generic processor mode.

EOT

(1)

RD_N, WR_N

004aaa378

36 ns (min)

DREQ th1

Fig 24. Typical interface connections for generic processor mode.

004aaa206

data

read strobe

ISP1582

CPU

DATA[15:0]

RD_N

address 8 A[7:0]

write strobe WR_N

chip select CS_N

In full-speed mode, an internal 1.5 kΩ pull-up resistor is connected to pin DP.

Fig 25. Load impedance for pins DP and DM (full-speed mode).

test point

50 pF

15 kΩ

D.U.T

MGT495

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 61 of 66

16. Package outline

Fig 26. HVQFN56 package outline.

0.5

A1Eh

UNIT ye

0.2

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

4.45

4.15

4.45

4.15

6.5

0.30

0.18

0.05

0.00 8.1

7.9 8.1

7.9 0.05 0.1

DIMENSIONS (mm are the original dimensions)

SOT684-1 MO-220 - - -- - -

0.5

0.3

0.1

0.05

0 2.5 5 mm

scale

SOT684-1

HVQFN56: plastic thermal enhanced very thin quad flat package; no leads;

56 terminals; body 8 x 8 x 0.85 mm

A(1)

max.

AA1c

detail X

y1C

15 28

56 43

01-08-08

02-10-22

terminal 1

index area

terminal 1

index area

1/2 e

E(1)

Note

1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.

D(1)

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 62 of 66

17. Soldering

17.1 Introduction to soldering surface mount packages

This text gives a very brief insight to a complex technology. A more in-depth account

of soldering ICs can be found in our

Data Handbook IC26; Integrated Circuit

Packages

(document order number 9398 652 90011).

There is no soldering method that is ideal for all surface mount IC packages. Wave

soldering can still be used for certain surface mount ICs, but it is not suitable for ﬁne

pitch SMDs. In these situations reﬂow soldering is recommended. In these situations

reﬂow soldering is recommended.

17.2 Reﬂow soldering

Reﬂow soldering requires solder paste (a suspension of ﬁne solder particles, ﬂux and

binding agent) to be applied to the printed-circuit board by screen printing, stencilling

or pressure-syringe dispensing before package placement. Driven by legislation and

environmental forces the worldwide use of lead-free solder pastes is increasing.

Several methods exist for reﬂowing; for example, convection or convection/infrared

heating in a conveyor type oven. Throughput times (preheating, soldering and

cooling) vary between 100 and 200 seconds depending on heating method.

Typical reﬂow peak temperatures range from 215 to 270 °C depending on solder

paste material. The top-surface temperature of the packages should preferably be

kept:

•below 225 °C (SnPb process) or below 245 °C (Pb-free process)

–for all BGA, HTSSON..T and SSOP..T packages

–for packages with a thickness ≥2.5 mm

–for packages with a thickness < 2.5 mm and a volume ≥350 mm3 so called

thick/large packages.

•below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with

a thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages.

Moisture sensitivity precautions, as indicated on packing, must be respected at all

times.

17.3 Wave soldering

Conventional single wave soldering is not recommended for surface mount devices

(SMDs) or printed-circuit boards with a high component density, as solder bridging

and non-wetting can present major problems.

To overcome these problems the double-wave soldering method was speciﬁcally

developed.

If wave soldering is used the following conditions must be observed for optimal

results:

•Use a double-wave soldering method comprising a turbulent wave with high

upward pressure followed by a smooth laminar wave.

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 63 of 66

•For packages with leads on two sides and a pitch (e):

–larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be

parallel to the transport direction of the printed-circuit board;

–smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the

transport direction of the printed-circuit board.

The footprint must incorporate solder thieves at the downstream end.

•For packages with leads on four sides, the footprint must be placed at a 45° angle

to the transport direction of the printed-circuit board. The footprint must

incorporate solder thieves downstream and at the side corners.

During placement and before soldering, the package must be ﬁxed with a droplet of

adhesive. The adhesive can be applied by screen printing, pin transfer or syringe

dispensing. The package can be soldered after the adhesive is cured.

Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 °C or

265 °C, depending on solder material applied, SnPb or Pb-free respectively.

A mildly-activated ﬂux will eliminate the need for removal of corrosive residues in

most applications.

17.4 Manual soldering

Fix the component by ﬁrst soldering two diagonally-opposite end leads. Use a low

voltage (24 V or less) soldering iron applied to the ﬂat part of the lead. Contact time

must be limited to 10 seconds at up to 300 °C.

When using a dedicated tool, all other leads can be soldered in one operation within

2 to 5 seconds between 270 and 320 °C.

17.5 Package related soldering information

[1] For more detailed information on the BGA packages refer to the

(LF)BGA Application Note

(AN01026); order a copy from your Philips Semiconductors sales ofﬁce.

[2] All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the

maximum temperature (with respect to time) and body size of the package, there is a risk that internal

or external package cracks may occur due to vaporization of the moisture in them (the so called

popcorn effect). For details, refer to the Drypack information in the

Data Handbook IC26; Integrated

Circuit Packages; Section: Packing Methods

Table 87: Suitability of surface mount IC packages for wave and reﬂow soldering

methods

Package[1] Soldering method

Wave Reﬂow[2]

BGA, HTSSON..T[3], LBGA, LFBGA, SQFP,

SSOP..T[3], TFBGA, USON, VFBGA not suitable suitable

DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,

HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,

HVSON, SMS

not suitable[4] suitable

PLCC[5], SO, SOJ suitable suitable

LQFP, QFP, TQFP not recommended[5][6] suitable

SSOP, TSSOP, VSO, VSSOP not recommended[7] suitable

CWQCCN..L[8], PMFP[9], WQCCN..L[8] not suitable not suitable

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 64 of 66

[3] These transparent plastic packages are extremely sensitive to reﬂow soldering conditions and must

on no account be processed through more than one soldering cycle or subjected to infrared reﬂow

soldering with peak temperature exceeding 217 °C±10 °C measured in the atmosphere of the reﬂow

oven. The package body peak temperature must be kept as low as possible.

[4] These packages are not suitable for wave soldering. On versions with the heatsink on the bottom

side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with

the heatsink on the top side, the solder might be deposited on the heatsink surface.

[5] If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave

direction. The package footprint must incorporate solder thieves downstream and at the side corners.

[6] Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it

is deﬁnitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.

[7] Wave soldering is suitable for SSOP, TSSOP, VSO and VSOP packages with a pitch (e) equal to or

larger than 0.65 mm; it is deﬁnitely not suitable for packages with a pitch (e) equal to or smaller than

0.5 mm.

[8] Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered

pre-mounted on ﬂex foil. However, the image sensor package can be mounted by the client on a ﬂex

foil by using a hot bar soldering process. The appropriate soldering proﬁle can be provided on

request.

[9] Hot bar soldering or manual soldering is suitable for PMFP packages.

18. Revision history

Table 88: Revision history

Rev Date CPCN Description

03 2004xxxx - Preliminary data (9397 750 13699)

Modiﬁcations:

•Globally changed VCC(I/O) to the same value as VCC.

•Table 2 “Pin description”: updated pin description for EOT, DACK, DIOW and DIOR; also

removed table note 3.

•Section 8.14.1 “Power-sharing mode”: added Remark.

•Section 9.5.4 “Scratch register (address: 78h)”: updated the bus reset value.

02 20040629 - Preliminary data (9397 750 12979)

01 20040223 - Preliminary data (9397 750 11496)

9397 750 13699

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

Preliminary data Rev. 03 — 25 August 2004 65 of 66

Contact information

For additional information, please visit http://www.semiconductors.philips.com.

For sales ofﬁce addresses, send e-mail to: sales.addresses@www.semiconductors.philips.com.Fax: +31 40 27 24825

19. Data sheet status

[1] Please consult the most recently issued data sheet before initiating or completing a design.

[2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at

URL http://www.semiconductors.philips.com.

[3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.

20. Deﬁnitions

Short-form speciﬁcation — The data in a short-form speciﬁcation is

extracted from a full data sheet with the same type number and title. For

detailed information see the relevant data sheet or data handbook.

Limiting values deﬁnition — Limiting values given are in accordance with

the Absolute Maximum Rating System (IEC 60134). Stress above one or

more of the limiting values may cause permanent damage to the device.

These are stress ratings only and operation of the device at these or at any

other conditions above those given in the Characteristics sections of the

speciﬁcation is not implied. Exposure to limiting values for extended periods

may affect device reliability.

Application information — Applications that are described herein for any

of these products are for illustrative purposes only. Philips Semiconductors

make no representation or warranty that such applications will be suitable for

the speciﬁed use without further testing or modiﬁcation.

21. Disclaimers

Life support — These products are not designed for use in life support

appliances, devices, or systems where malfunction of these products can

reasonably be expected to result in personal injury. Philips Semiconductors

customers using or selling these products for use in such applications do so

at their own risk and agree to fully indemnify Philips Semiconductors for any

damages resulting from such application.

Right to make changes — Philips Semiconductors reserves the right to

make changes in the products - including circuits, standard cells, and/or

software - described or contained herein in order to improve design and/or

performance. When the product is in full production (status ‘Production’),

relevant changes will be communicated via a Customer Product/Process

Change Notiﬁcation (CPCN). Philips Semiconductors assumes no

responsibility or liability for the use of any of these products, conveys no

licence or title under any patent, copyright, or mask work right to these

products, and makes no representations or warranties that these products are

free from patent, copyright, or mask work right infringement, unless otherwise

speciﬁed.

22. Trademarks

ACPI — is an open industry speciﬁcation for PC power management,

co-developed by Intel Corp., Microsoft Corp. and Toshiba

OnNow — is a trademark of Microsoft Corp.

SoftConnect — is a trademark of Koninklijke Philips Electronics N.V.

Level Data sheet status[1] Product status[2][3] Deﬁnition

I Objective data Development This data sheet contains data from the objective speciﬁcation for product development. Philips

Semiconductors reserves the right to change the speciﬁcation in any manner without notice.

II Preliminary data Qualiﬁcation This data sheet contains data fromthe preliminary speciﬁcation. Supplementary data will be published

at a later date. Philips Semiconductors reserves the right to change the speciﬁcation without notice, in

order to improve the design and supply the best possible product.

III Product data Production This data sheet contains data from the product speciﬁcation. Philips Semiconductors reserves the

right to make changes at any time in order to improve the design, manufacturing and supply. Relevant

changes will be communicated via a Customer Product/Process Change Notiﬁcation (CPCN).

Printed in The Netherlands

All rights are reserved. Reproduction in whole or in part is prohibited without the prior

written consent of the copyright owner.

The information presented in this document does not form part of any quotation or

contract, is believed to be accurate and reliable and may be changed without notice. No

liability will be accepted by the publisher for any consequence of its use. Publication

thereof does not convey nor imply any license under patent- or other industrial or

intellectual property rights.

Date of release: 25 August 2004 Document order number: 9397 750 13699

Contents

Philips Semiconductors ISP1582

Hi-Speed USB peripheral controller

1 General description. . . . . . . . . . . . . . . . . . . . . . 1

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . 3

5 Ordering information. . . . . . . . . . . . . . . . . . . . . 3

6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4

7 Pinning information. . . . . . . . . . . . . . . . . . . . . . 5

7.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6

8 Functional description . . . . . . . . . . . . . . . . . . 10

8.1 DMA interface, DMA handler and DMA

registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

8.2 Hi-Speed USB transceiver . . . . . . . . . . . . . . . 11

8.3 MMU and integrated RAM . . . . . . . . . . . . . . . 11

8.4 Microcontroller interface and

microcontroller handler . . . . . . . . . . . . . . . . . 11

8.5 OTG SRP module. . . . . . . . . . . . . . . . . . . . . . 11

8.6 Philips high-speed transceiver . . . . . . . . . . . . 11

8.6.1 Philips Parallel Interface Engine (PIE) . . . . . . 11

8.6.2 Peripheral circuit. . . . . . . . . . . . . . . . . . . . . . . 11

8.6.3 HS detection. . . . . . . . . . . . . . . . . . . . . . . . . . 12

8.7 Philips Serial Interface Engine (SIE). . . . . . . . 12

8.8 SoftConnect . . . . . . . . . . . . . . . . . . . . . . . . . . 12

8.9 System controller . . . . . . . . . . . . . . . . . . . . . . 12

8.10 Output pins status. . . . . . . . . . . . . . . . . . . . . . 12

8.11 Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

8.11.1 Interrupt output pin . . . . . . . . . . . . . . . . . . . . . 13

8.11.2 Interrupt control . . . . . . . . . . . . . . . . . . . . . . . 15

8.12 VBUS sensing . . . . . . . . . . . . . . . . . . . . . . . . . 15

8.13 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . 16

8.14 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . 17

8.14.1 Power-sharing mode. . . . . . . . . . . . . . . . . . . . 18

8.14.2 Self-powered mode. . . . . . . . . . . . . . . . . . . . . 20

8.14.3 Bus-powered mode. . . . . . . . . . . . . . . . . . . . . 21

9 Register description . . . . . . . . . . . . . . . . . . . . 23

9.1 Register access . . . . . . . . . . . . . . . . . . . . . . . 24

9.2 Initialization registers . . . . . . . . . . . . . . . . . . . 24

9.2.1 Address register (address: 00h) . . . . . . . . . . . 24

9.2.2 Mode register (address: 0Ch). . . . . . . . . . . . . 25

9.2.3 Interrupt Conﬁguration register (address: 10h) 27

9.2.4 OTG register (address: 12h). . . . . . . . . . . . . . 28

9.2.5 Interrupt Enable register (address: 14h). . . . . 30

9.3 Data ﬂow registers . . . . . . . . . . . . . . . . . . . . . 31

9.3.1 Endpoint Index register (address: 2Ch) . . . . . 31

9.3.2 Control Function register (address: 28h) . . . . 33

9.3.3 Data Port register (address: 20h) . . . . . . . . . . 33

9.3.4 Buffer Length register (address: 1Ch) . . . . . . 34

9.3.5 Buffer Status register (address: 1Eh) . . . . . . . 35

9.3.6 Endpoint MaxPacketSize register (address:

04h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

9.3.7 Endpoint Type register (address: 08h) . . . . . . 37

9.4 DMA registers . . . . . . . . . . . . . . . . . . . . . . . . 38

9.4.1 DMA Command register (address: 30h) . . . . 39

9.4.2 DMA Transfer Counter register (address: 34h) 40

9.4.3 DMA Conﬁguration register (address: 38h) . . 41

9.4.4 DMA Hardware register (address: 3Ch). . . . . 42

9.4.5 DMA Interrupt Reason register (address: 50h) 43

9.4.6 DMA Interrupt Enable register (address: 54h) 45

9.4.7 DMA Endpoint register (address: 58h). . . . . . 45

9.4.8 DMA Burst Counter register (address: 64h). . 46

9.5 General registers . . . . . . . . . . . . . . . . . . . . . . 46

9.5.1 Interrupt register (address: 18h). . . . . . . . . . . 46

9.5.2 Chip ID register (address: 70h) . . . . . . . . . . . 48

9.5.3 Frame Number register (address: 74h) . . . . . 49

9.5.4 Scratch register (address: 78h) . . . . . . . . . . . 49

9.5.5 Unlock Device register (address: 7Ch). . . . . . 50

9.5.6 Test Mode register (address: 84h) . . . . . . . . . 51

10 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 52

11 Recommended operating conditions . . . . . . 52

12 Static characteristics . . . . . . . . . . . . . . . . . . . 53

13 Dynamic characteristics. . . . . . . . . . . . . . . . . 54

13.1 Register access timing. . . . . . . . . . . . . . . . . . 57

13.2 DMA timing. . . . . . . . . . . . . . . . . . . . . . . . . . . 58

14 Application information . . . . . . . . . . . . . . . . . 60

15 Test information. . . . . . . . . . . . . . . . . . . . . . . . 60

16 Package outline. . . . . . . . . . . . . . . . . . . . . . . . 61

17 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

17.1 Introduction to soldering surface mount

packages. . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

17.2 Reﬂow soldering. . . . . . . . . . . . . . . . . . . . . . . 62

17.3 Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 62

17.4 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 63

17.5 Package related soldering information. . . . . . 63

18 Revision history . . . . . . . . . . . . . . . . . . . . . . . 64

19 Data sheet status. . . . . . . . . . . . . . . . . . . . . . . 65

20 Deﬁnitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

21 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

22 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 65