Product Specification PE43503 50 RF Digital Attenuator 5-bit, 31 dB, 9 kHz - 6.0 GHz Product Description The PE43503 is a HaRPTM-enhanced, high linearity, 5-bit RF Digital Step Attenuator (DSA) covering a 31 dB attenuation range in 1 dB steps. The Peregrine 50 RF DSA provides a serial CMOS control interface. It maintains high attenuation accuracy over frequency and temperature and exhibits very low insertion loss and low power consumption. Performance does not change with Vdd due to on-board regulator. This next generation Peregrine DSA is available in a 4x4 mm 24-lead QFN footprint. Features * HaRPTM-enhanced UltraCMOSTM device The PE43503 is manufactured on Peregrine's UltraCMOSTM process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. * Programming Modes: * Attenuation: 1 dB steps to 31 dB * High Linearity: Typical +58 dBm IP3 * Excellent low-frequency performance * 3.3 V or 5.0 V Power Supply Voltage * Fast switch settling time * * Direct Parallel Latched Parallel * Serial * High-attenuation state @ power-up (PUP) * CMOS Compatible Figure 1. Package Type * No DC blocking capacitors required 24-lead 4x4x0.85 mm QFN Package * Packaged in a 24-lead 4x4x0.85 mm QFN Figure 2. Functional Schematic Diagram Switched Attenuator Array RF Output RF Input Parallel Control 5 Serial In Control Logic Interface CLK LE A0 A1 Document No. 70-0252-05 www.psemi.com A2 P/S (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 11 PE43503 Product Specification Table 1. Electrical Specifications @ +25C, VDD = 3.3 V or 5.0 V Parameter Test Conditions Frequency Min. Frequency Range Typical Max. 9 kHz Attenuation Range 1 dB Step 0 - 31 9 kHz 6 GHz Insertion Loss dB 2.4 9 kHz 4 GHz 4 GHz 6 GHz 4 GHz 6 GHz 4 GHz 6 GHz Attenuation Error 0dB - 31dB Attenuation settings 0dB - 21dB Attenuation settings 22dB - 31dB Attenuation settings 0dB - 31dB Attenuation settings Relative Phase P1dB (note 1) Input IP3 All States Input Two tones at +18 dBm, 20 MHz spacing 9 kHz 6 GHz 20 MHz - 6 GHz 20 MHz - 6 GHz 30 DC 6 GHz Return Loss Switching Speed Units 6 GHz 50% DC CTRL to 10% / 90% RF Typical Spurious Value 1 MHz Video Feed Through RF Trise/Tfall 10% / 90% RF Settling Time RF settled to within 0.05 dB of final value RBW = 5 MHz, Averaging ON. 2.9 dB (0.3+3%) +0.4+9% +2.4+0% -0.2-3% dB dB dB dB 72 32 +58 dBm dBm 17 dB 650 ns -115 dBm 10 mVpp 400 ns 4 s Note 1. Please note Maximum Operating Pin (50) of +23dBm as shown in Table 3. Performance Plots Figure 3. 1dB Step Error vs. Frequency * 200MHz 3000MHz 900MHz 4000MHz 1800MHz 5000MHz Figure 4. 1dB Attenuation vs. Attenuation State Attenuation 2200MHz 6000MHz 35 2 Attenuation (dB) dB Step Error (dB) 30 1 0 900 MHz 2200 MHz 3800 MHz 5800 MHz 25 20 15 10 5 0 -1 0 4 8 12 16 20 24 28 0 32 5 10 Attenuation Setting (dB) 1dB State 8dB State 2 2dB State 16dB State 25 30 35 Figure 6. 1dB Attenuation Error vs. Frequency 200MHz 3000MHz 4dB State 31dB State 900MHz 4000MHz 1800MHz 5000MHz 2200MHz 6000MHz 2 1.5 Attenuation Error (dB) 1.5 1 Bit Error (dB) 20 Attenuation State *Monotonicity is held so long as Step-Error does not cross below -1 Figure 5. 1dB Major State Bit Error 15 0.5 0 -0.5 -1 -1.5 1 0.5 0 -0.5 -1 -1.5 -2 -2 0 1000 2000 3000 4000 5000 Frequency (GHz) (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 11 6000 0 4 8 12 16 20 24 28 Attenuation Setting (dB) Document No. 70-0252-05 UltraCMOSTM RFIC Solutions 32 PE43503 Product Specification Figure 7. Insertion Loss vs. Temperature -40C +25C Figure 8. Input Return Loss vs. Attenuation @ T = +25C +85C 0.5dB 8dB Input Return Loss (dB) -1 -1.5 -2 -2.5 -15 -20 -25 -30 -35 -40 -3.5 0 2 4 6 8 0 10 1 2 3 0dB 4dB 0.5dB 8dB 1dB 16dB 2dB 31dB -5 -20 -25 -30 -35 -40 3 4 5 6 7 8 1dB 16dB 9 2dB 31dB 4dB 60 40 20 0 9 0 1 2 3 4 5 6 7 8 Frequency (GHz) Figure 11. Attenuation Error vs. Temperature @ 6 GHz -40C 8 80 Frequency (GHz) 2 7 100 -45 2 6 120 Relative Phase Error (Deg) -15 1 0dB 8dB 140 -10 0 5 Figure 10. Relative Phase vs. Frequency Figure 9. Output Return Loss vs. Attenuation @ T = +25C 0 4 Frequency (GHz) Frequency (GHz) Return Loss (dB) 2dB 31dB -10 -3 +25C Figure 12. Input IP3 vs. Frequency +85C 0dB 8dB 70 1.5 65 1 60 Input IP3 (dBm) Attenuation Error (dB) 1dB 16dB -5 -0.5 Insertion Loss (dB) 0dB 4dB 0 0 0.5 0 -0.5 1dB 16dB 2dB 31dB 4dB 55 50 45 -1 40 -1.5 35 30 -2 0 4 8 12 16 20 Attenuation Setting (dB) Document No. 70-0252-05 www.psemi.com 24 28 32 0 500 1000 1500 2000 2500 3000 3500 4000 4500 Frequency (MHz) (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 11 PE43503 Product Specification Figure 13. Pin Configuration (Top View) Table 3. Operating Ranges GND C1 C2 C4 C8 C16 24 23 22 21 20 Parameter 19 VDD Power Supply Voltage Min Typ 3.0 3.3 Max Units V NC 1 18 SI VDD 2 17 CLK VDD Power Supply Voltage 5.0 5.5 V 16 LE IDD Power Supply Current 70 350 A 15 5.5 V Fig. 14 +23 dBm dBm 85 C P/S 3 GND 4 GND Digital Input High RF1 5 14 RF2 GND 6 13 GND PIN Input power (50): 9 kHz 20 MHz 20 MHz 6 GHz 7 8 9 10 11 12 GND GND GND GND GND GND Exposed Solder Pad TOP Operating temperature range Pin Name NC No Connect 2 VDD Power supply pin 3 P/S Serial/Parallel mode select 4 GND Ground VDD 5 RF1 RF1 port GND Ground GND Ground 13 GND Ground 14 RF2 RF2 port 15 GND Ground 0 16 LE 17 CLK Serial interface Clock input Serial interface Latch Enable input 18 SI Serial interface Data input 19 C16 (D6) Parallel control bit, 16 dB 20 C8 (D5) Parallel control bit, 8 dB 21 C4 (D4) Parallel control bit, 4 dB 22 C2 (D3) Parallel control bit, 2 dB 23 C1 (D2) Parallel control bit, 1 dB 24 GND 1 V 15 A Units Note 1. Input leakage current per Control pin 1 6 25 Digital Input Leakage1 Description 7 - 12 -40 Digital Input Low Table 2. Pin Descriptions Pin No. 2.6 Table 4. Absolute Maximum Ratings Symbol Min Max Power supply voltage Parameter/Conditions -0.3 6.0 V VI Voltage on any Digital input -0.3 5.8 V TST Storage temperature range -65 150 C Fig. 14 +23 500 100 dBm dBm V V Input power (50) 9 kHz 20 MHz 20 MHz 6 GHz ESD voltage (HBM)1 ESD voltage (Machine Model) PIN VESD Note: 1. Human Body Model (HBM, MIL_STD 883 Method 3015.7) Exceeding absolute maximum ratings may cause permanent damage. Operation should be restricted to the limits in the Operating Ranges table. Operation between operating range maximum and absolute maximum for extended periods may reduce reliability. Figure 14. Maximum Power Handling Capability Ground 30 Note: Ground C1, C2, C4, C8, C16 if not in use. 25 Exposed Solder Pad Connection 20 Pin (dBm) The exposed solder pad on the bottom of the package must be grounded for proper device operation. 15 10 Moisture Sensitivity Level The Moisture Sensitivity Level rating for the PE43503 in the 24-lead 4x4 QFN package is MSL1. 5 0 1.0E+03 1.0E+04 1.0E+05 1.0E+06 Switching Frequency The PE43503 has a maximum 25 kHz switching rate. Switching rate is defined to be the speed at which the DSA can be toggled across attenuation states. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOSTM devices are immune to latch-up. (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 11 1.0E+07 1.0E+08 1.0E+09 Hz Electrostatic Discharge (ESD) Precautions When handling this UltraCMOSTM device, observe the same precautions that you would use with other ESDsensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the specified rating. Document No. 70-0252-05 UltraCMOSTM RFIC Solutions PE43503 Product Specification Table 5. Control Voltage State Bias Condition Low 0 to +1.0 Vdc at 2 A (typ) High +2.6 to +5 Vdc at 10 A (typ) Table 6. Latch and Clock Specifications Latch Enable Shift Clock Function X X Shift Register Clocked Contents of shift register transferred to attenuator core Table 7. Parallel Truth Table Parallel Control Setting Table 8. Attenuation Word Truth Table Attenuation Word D1 D0 (LSB) Attenuation Setting RF1-RF2 D6 D5 D4 D3 D2 Attenuation Setting RF1-RF2 L L L L L Reference I.L. L L L L L L L L Reference I.L. L L L L H 1 dB L L L L L H L L 1 dB L L L H L 2 dB L L L L H L L L 2 dB L L H L L 4 dB L L L H L L L L 4 dB L H L L L 8 dB L L H L L L L L 8 dB H L L L L 16 dB L H L L L L L L 16 dB H H H H H 31 dB L H H H H H L L 31 dB D7 D6 D5 D4 D3 D2 Table 9. Serial Register Map MSB (last in) LSB (first in) Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 D7 D6 D5 D4 D3 D2 D1 D0 Bits must be set to logic low Attenuation Word Attenuation Word is derived directly from the attenuation value. For example, to program the 13 dB state: Attenuation Word: Multiply by 4 and convert to binary 4 *13 dB 52 00110100 Serial Input: 00110100 Document No. 70-0252-05 www.psemi.com (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 11 PE43503 Product Specification Programming Options Parallel/Serial Selection Either a parallel or serial interface can be used to control the PE43503. The P/S bit provides this selection, with P/S=LOW selecting the parallel interface and P/S=HIGH selecting the serial interface. Parallel Mode Interface The parallel interface consists of five CMOScompatible control lines that select the desired attenuation state, as shown in Table 7. The parallel interface timing requirements are defined by Fig. 16 (Parallel Interface Timing Diagram), Table 11 (Parallel Interface AC Characteristics), and switching speed (Table 1). For latched-parallel programming the Latch Enable (LE) should be held LOW while changing attenuation state control values, then pulse LE HIGH to LOW (per Fig. 16) to latch new attenuation state into device. For direct parallel programming, the Latch Enable (LE) line should be pulled HIGH. Changing attenuation state control values will change device state to new attenuation. Direct Mode is ideal for manual control of the device (using hardwire, switches, or jumpers). Serial Interface The serial interface is a 8-bit serial-in, parallel-out shift register buffered by a transparent latch. The 8bits make up the Attenuation Word that controls the DSA. Fig. 15 illustrates a example timing diagram for programming a state. When the DSA is used in serial mode, ground all parallel control pins (pins 1923). The serial-interface is controlled using three CMOScompatible signals: Serial-In (SI), Clock (CLK), and Latch Enable (LE). The SI and CLK inputs allow data to be serially entered into the shift register. Serial data is clocked in LSB first. (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 11 The shift register must be loaded while LE is held LOW to prevent the attenuator value from changing as data is entered. The LE input should then be toggled HIGH and brought LOW again, latching the new data into the DSA. Attenuation Word truth table is listed in Table 8. A programming example of the serial register is illustrated in Table 9. The serial timing diagram is illustrated in Fig. 15. It is required that all parallel pins be grounded when the DSA is used in serial mode. Power-up Control Settings The PE43503 will always initialize to the maximum attenuation setting (31 dB) on power-up for both the serial and latched-parallel modes of operation and will remain in this setting until the user latches in the next programming word. In direct-parallel mode, the DSA can be preset to any state within the 31 dB range by pre-setting the parallel control pins prior to power-up. In this mode, there is a 400-s delay between the time the DSA is powered-up to the time the desired state is set. During this power-up delay, the device attenuates to the maximum attenuation setting (31 dB) before defaulting to the user defined state. If the control pins are left floating in this mode during power-up, the device will default to the minimum attenuation setting (insertion loss state). Dynamic operation between serial and parallel programming modes is possible. If the DSA powers up in serial mode (P/S = HIGH), all the parallel control inputs DI[6:2] must be set to logic low. Prior to toggling to parallel mode, the DSA must be programmed serially to ensure D[7] is set to logic low. If the DSA powers up in either latched or directparallel mode, all parallel pins DI[6:2] must be set to logic low prior to toggling to serial mode (P/S = HIGH), and held low until the DSA has been programmed serially to ensure bit D[7] is set to logic low. The sequencing is only required once on powerup. Once completed, the DSA may be toggled between serial and parallel programming modes at will. Document No. 70-0252-05 UltraCMOSTM RFIC Solutions PE43503 Product Specification Figure 15. Serial Timing Diagram Bits can either be set to logic high or logic low D[0], D[1] and D[7] must be set to logic low DI[6:2] TDISU TDIH P/S T PSSU TPSIH D[0] SI TSISU D[1] D[2] D[3] D[4] D[5] D[6] D[7] TSIH CLK TCLKL TCLKH TLESU LE TLEPW DO[6:0] TPD VALID Figure 16. Latched-Parallel/Direct-Parallel Timing Diagram P/S TPSSU DI[6:2] TPSIH VALID TDISU TDIH LE TLEPW DO[6:2] VALID TDIPD TPD Table 10. Serial Interface AC Characteristics VDD = 3.3 or 5.0 V, -40 C < TA < 85 C, unless otherwise specified Symbol FCLK Parameter Min Max Unit - 10 MHz Serial clock frequency TCLKH Serial clock HIGH time 30 - ns TCLKL Serial clock LOW time 30 - ns TLESU Last serial clock rising edge setup time to Latch Enable rising edge 10 - ns TLEPW Latch Enable min. pulse width 30 - ns TSISU Serial data setup time 10 - TSIH Serial data hold time 10 TDISU Parallel data setup time TDIH Parallel data hold time TASU Address setup time 100 - ns TAH Address hold time 100 - ns TPSSU Parallel/Serial setup time 100 - ns TPSH Parallel/Serial hold time 100 - ns TPD Digital register delay (internal) - 10 ns Document No. 70-0252-05 www.psemi.com Table 11. Parallel and Direct Interface AC Characteristics VDD = 3.3 or 5.0 V, -40 C < TA < 85 C, unless otherwise specified Symbol Parameter Min Max Unit TLEPW Latch Enable minimum pulse width 30 - ns TDISU Parallel data setup time 100 - ns TDIH Parallel data hold time 100 - ns TPSSU Parallel/Serial setup time 100 - ns ns TPSIH Parallel/Serial hold time 100 - ns - ns TPD - 10 ns 100 - ns Digital register delay (internal) 100 - ns Digital register delay (internal, direct mode only) - 5 ns TDIPD (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 11 PE43503 Product Specification Evaluation Kit The Digital Attenuator Evaluation Kit board was designed to ease customer evaluation of the PE43503 Digital Step Attenuator. Figure 17. Evaluation Board Layout Peregrine Specification 101-0310 Direct-Parallel Programming Procedure For automated direct-parallel programming, connect the test harness provided with the EVK from the parallel port of the PC to the J1 & Serial header pin and set the D0-D6 SP3T switches to the `MIDDLE' toggle position. Position the Parallel/Serial (P/S) select switch to the Parallel (or left) position. The evaluation software is written to operate the DSA in either Parallel or Serial-Addressable Mode. Ensure that the software is set to program in Direct-Parallel mode. Using the software, enable or disable each setting to the desired attenuation state. The software automatically programs the DSA each time an attenuation state is enabled or disabled. For manual direct-parallel programming, disconnect the test harness provided with the EVK from the J1 and Serial header pins. Position the Parallel/Serial (P/S) select switch to the Parallel (or left) position. The LE pin on the Serial header must be tied to VDD. Switches D0-D6 are SP3T switches which enable the user to manually program the parallel bits. When any input D0-D6 is toggled `UP', logic high is presented to the parallel input. When toggled `DOWN', logic low is presented to the parallel input. Setting D0-D6 to the `MIDDLE' toggle position presents an OPEN, which forces an on-chip logic low. Table 9 depicts the parallel programming truth table and Fig. 16 illustrates the parallel programming timing diagram. Latched-Parallel Programming Procedure For automated latched-parallel programming, the procedure is identical to the direct-parallel method. The user only must ensure that LatchedParallel is selected in the software. For manual latched-parallel programming, the procedure is identical to direct-parallel except now the LE pin on the Serial header must be logic low (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 8 of 11 Note: Reference Figure 18 for Evaluation Board Schematic as the parallel bits are applied. The user must then pulse LE from 0V to VDD and back to 0V to latch the programming word into the DSA. LE must be logic low prior to programming the next word. Serial Programming Procedure Position the Parallel/Serial (P/S) select switch to the Serial (or right) position. The evaluation software is written to operate the DSA in either Parallel or Serial Mode. Ensure that the software is set to program in Serial mode. Using the software, enable or disable each setting to the desired attenuation state. The software automatically programs the DSA each time an attenuation state is enabled or disabled. Document No. 70-0252-05 UltraCMOSTM RFIC Solutions PE43503 Product Specification Figure 18. Evaluation Board Schematic Peregrine Specification 102-0379 4 2 1 4 3 3 D6 D6 D5 3 D4 3 D3 3 D2 2 1 4 2 1 4 2 1 4 2 1 4 D1 3 D5 D4 D3 D2 D0 P/ S 5 D1 3 D0 P/S 2 1 4 2 1 6 4 VDD J1 HEADER 14 D0 1 3 5 7 9 11 13 D1 D2 D3 D4 D5 D6 2 D5 D3 D6 19 21 22 20 C8 C16 18 17 LE 16 GND 15 5 RF1 RF2 14 6 GND GND 13 J5 SMA 1 Z=50 Ohm J7 SMA 1 2 2 1 43X0X DSA 50 Ohm 4x4 MLP24 SI CLK CLOCK DATA LE GND 2 Z=50 Ohm 1 De-embeding trace Z=50 Ohm GND GND 100pF J4 SMA J6 SMA 4 U1 GND 100pF S/P 1 2 3 4 12 100pF 3 C14 11 100pF 0.1F C13 VDD GND C8 CP25 2 GND C10 1 P/S 7 C9 D0 VDD GND 1 2 C4 CP5 VDD J3 CON2 C2 100pF 100pF 9 100pF SERIAL HEADER 4 CLK DATA LE C4 C3 24 100pF D4 D1 100pF C2 10 C1 C7 D2 C6 100pF 23 C5 100pF C1 1 3 5 7 9 11 13 GND 2 4 6 8 10 12 14 8 2 4 6 8 10 12 14 Note: Capacitors C1-C8, C13, & C14 may be omitted. Figure 19. Package Drawing Document No. 70-0252-05 www.psemi.com (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 9 of 11 PE43503 Product Specification Figure 20. Tape and Reel Drawing Tape Feed Direction Pin 1 A0 = 4.35 B0 = 4.35 K0 = 1.1 Top of Device Device Orientation in Tape Figure 21. Marking Specifications 43503 YYWW ZZZZZ YYWW = Date Code ZZZZZ = Last five digits of Lot Number Table 12. Ordering Information Order Code Part Marking Description Package Shipping Method EK-43503-01 PE43503 -EK PE43503 - 24QFN 4x4mm-EK Evaluation Kit 1 / Box PE43503 MLI 43503 PE43503 G - 24QFN 4x4mm-75A Green 24-lead 4x4mm QFN Bulk or tape cut from reel PE43503 MLI-Z 43503 PE43503 G - 24QFN 4x4mm-3000C Green 24-lead 4x4mm QFN 3000 units / T&R Document No. 70-0252-05 www.psemi.com (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 10 of 11 PE43503 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation Peregrine Semiconductor, Asia Pacific (APAC) 9380 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 Europe Peregrine Semiconductor Europe Batiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173 High-Reliability and Defense Products Peregrine Semiconductor, Korea #B-2607, Kolon Tripolis, 210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-943 South Korea Tel: +82-31-728-3939 Fax: +82-31-728-3940 Peregrine Semiconductor K.K., Japan Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Americas San Diego, CA, USA Phone: 858-731-9475 Fax: 848-731-9499 Europe/Asia-Pacific Aix-En-Provence Cedex 3, France Phone: +33-4-4239-3361 Fax: +33-4-4239-7227 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a CNF (Customer Notification Form). (c)2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 11 of 11 The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS, HaRP, MultiSwitch and DuNE are trademarks of Peregrine Semiconductor Corp. Document No. 70-0252-05 UltraCMOSTM RFIC Solutions