DA101MC-R - MURATA MANUFACTURING

DA100 Series

Transformers for Digital Audio Data Transmission

KMP_DA100C_C08 Page 1 of 3

www.murata-ps.com

www.murata-ps.com/support

For full details go to

www.cd4power.com/rohs

For full details go to

www.murata-ps.com/rohs

FEATURES

n RoHS compliant

n Compatible with leading chip sets

n 2kVrms isolation

n Industry-standard pinout

n Surface mount option

n UL 94 V-0 package materials

n Low proﬁle

n Suitable for both 75 & 110Ω circuits

n Toroidal construction

n Compliant with AES/EBU standards

n Fully encapsulated

DESCRIPTION

The Digital Audio Range of transformers is

designed to improve the balance of transmitter

and receiver circuitry in hi-ﬁ equipment,

video games and other applications requiring

high-performance digital audio transmission.

Compliant with AES/EBU recommendations for the

digital audio interface, offering optimised shunt

capacitance between primary and secondary

windings. Capable of operating over the audio

data rate frequency range, providing isolation from

50-60Hz noise.

Surface-mount parts

The surface-mount (M sufﬁx) products are not

recommended for new designs. For existing designs,

however, Murata Power Solutions will continue to

manufacture and fully support these parts.

For recommended alternatives please refer to the

DA100J Series datasheet.

SELECTION GUIDE

Order Code

Turns Ratio

Primary

Inductance

Max.

Leakage

Inductance

(100kHz, 10mV)

Min. Volt-time

Product, Et

Min. Return Loss

(100kHz-3MHz)

Typ. Common

Mode Rejection

(100kHz, 110Ω)

Isolation

(Flash tested

for 1 second)

mH μH Vμs dB dB Vrms

DA101C 1:1 1.00 - 2.06 0.26 15 46.80 52.10

2000

DA102C 1:1 2.00 - 3.90 0.39 20 40.40 49.70

DA103C 1:1 4.00 - 7.75 0.91 28 36.30 46.40

ORDER CODE DETAILS

Order Code Package Type Packaging Type Quantity

DAXXXC 6 Pin DIL Tube 50

DAXXXMC 6 Pin SM Tube 50

DAXXXMC-R 6 Pin SM Tape & Reel 500

ABSOLUTE MAXIMUM RATINGS

Operating free air temperature range 0°C to 70°C

Storage temperature range –40°C to 125°C

All speciﬁcations typical at TA =25°C

TECHNICAL NOTES

ISOLATION VOLTAGE

‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Volt-

age’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’

are all terms that relate to the same thing, a test voltage,

applied for a speciﬁed time, across a component designed

to provide electrical isolation, to verify the integrity of that

isolation.

All products in this series are 100% production tested at

their stated isolation voltage.

A question commonly asked is, “What is the continuous

voltage that can be applied across the part in normal opera-

tion?”

For a part holding no speciﬁc agency approvals both input

and output should normally be maintained within SELV limits

i.e. less than 42.4V peak, or 60VDC. The isolation test volt-

age represents a measure of immunity to transient voltages

and the part should never be used as an element of a safety

isolation system. The part could be expected to function cor-

rectly with several hundred volts offset applied continuously

across the isolation barrier; but then the circuitry on both

sides of the barrier must be regarded as operating at an

unsafe voltage and further isolation/insulation systems must

form a barrier between these circuits and any user-acces-

sible circuitry according to safety standard requirements.

REPEATED HIGH-VOLTAGE ISOLATION TESTING

It is well known that repeated high-voltage isolation

testing of a barrier component can actually degrade

isolation capability, to a lesser or greater degree

depending on materials, construction and environ-

ment. This series has toroidal isolation transformers,

with no additional insulation between primary and

secondary windings of enameled wire. While parts

can be expected to withstand several times the

stated test voltage, the isolation capability does de-

pend on the wire insulation. Any material, including

this enamel (typically polyurethane) is susceptible

to eventual chemical degradation when subject to

very high applied voltages thus implying that the

number of tests should be strictly limited. We there-

fore strongly advise against repeated high voltage

isolation testing, but if it is absolutely required, that

the voltage be reduced by 20% from speciﬁed test

voltage.

This consideration equally applies to agency recog-

nized parts rated for better than functional isolation

where the wire enamel insulation is always supple-

mented by a further insulation system of physical

spacing or barriers.

DA100 Series

Transformers for Digital Audio Data Transmission

KMP_DA100C_C08 Page 2 of 3

www.murata-ps.com/support

PACKAGE SPECIFICATIONS

MECHANICAL DIMENSIONS

RECOMMENDED FOOTPRINT DETAILS

6 Pin DIL 6 Pin SM

0.135±0.02

(3.44±0.50)

0.25

(6.35)

0.354

(9.0) Max.

0.375

(9.52) Max.

1 1

0.012 (0.30)

0.008 (0.20) 0.40

(10.16)

0.20

(5.08)

0.025 (0.63)

0.021 (0.53)

0.354

(9.0) Max.

0.375

(9.52) Max.

0.50

(12.70)

0.025 (0.63)

0.021 (0.53)

0.10

(2.54)

0.04

(0.90)

0.012 (0.30)

0.008 (0.20)

0.25

(6.35)

DA103MC

XYYWW

DA101C

XYYWW

Top View Top View

SOLDERING INFORMATION1

Pin ﬁnish Matte tin

Peak wave solder temperature 300˚C for 10 seconds

Peak reﬂow temperature 220˚C2

1 For further information, please visit www.murata-ps.com/rohs

2 For high temperature reﬂow parts see DA100J series datasheet.

0.10 (2.54)

Ø0.05 (1.20)+0.006 (0.15)

-0.000 (0.00)

0.45

(11.50)

0.10 (2.54)

0.04

(1.00)

0.06 (1.60)

6 Pin DIL 6 Pin SM

Unless otherwise stated all dimensions in inches (mm)

±0.01 (0.25). All pins on a 0.1 (2.54) pitch and within

±0.01 (0.25) of true position.

Unless otherwise stated all dimensions in inches (mm) ±0.01 (0.25).

All pins on a 0.1 (2.54) pitch and within ±0.01 (0.25) of true position.

Package Weight 0.93g Typ.

TUBE OUTLINE DIMENSIONS

0.023±0.005

(0.60±0.15)

0.16 (4.00)

0.22 (5.50)

0.43

(10.95)

0.51

(12.95)

0.15

(3.80)

0.62 (15.70)

Unless otherwise stated all

dimensions in inches (mm)

±0.01 (0.25).

Tube length: 18.3±0.08

(465±2).

Tube material: Antistatic coated

clear pvc.

0.10 (2.54)

Ø0.05 (1.20)+0.006 (0.15)

-0.000 (0.00)

0.45

(11.50)

0.10 (2.54)

0.04

(1.00)

0.06 (1.60)

DA100 Series

Transformers for Digital Audio Data Transmission

KMP_DA100C_C08 Page 3 of 3

Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other

technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply

the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Speciﬁcations are subject to change without

Murata Power Solutions, Inc.

11 Cabot Boulevard, Mansﬁeld, MA 02048-1151 U.S.A.

ISO 9001 and 14001 REGISTERED

www.murata-ps.com/support

TAPE & REEL SPECIFICATIONS

REEL OUTLINE DIMENSIONS

TAPE OUTLINE DIMENSIONS

1.20

(30.4) Max.

0.94-1.08 (23.9-27.4)

0.53 (13.50)

0.50 (12.80)

0.059 (1.50)

Min.

2.36 (60) Min.

0.80 (20.20) Min.

3.9 (100)

Min.

Leader section

15.7 (400) Min.

Goods

enclosure

section

Trailer section

6.3 (160) Min.

Ø15.039 (382) Max.

0.96 (24.4)

1.04 (26.4)



Unless otherwise stated all

dimensions in inches (mm) ±0.01(0.25).

* Includes ﬂange distortion at outer edge.

 Measured at hub.

0.024 (0.60) Max.

0.283 (7.20)

0.369 (9.37)

Direction of unreeling

0.069 (1.75)

0.453 (11.50)

0.157 (4.00) 0.079 (2.00)

0.472 (12.00)

Cover tape

0.059 (1.50 )

+0.004

-0.000 +0.10

-0.00

0.945 (24.00 )

+0.012

-0.004

+0.30

-0.10

DA10XXC

XYYWW

Unless otherwise stated all

dimensions in inches (mm) ±0.01(0.25).