SIDACtor (R) Protection Thyristors Broadband OptimizedTM Protection MC Series - TO-92 Description MC Series TO-92 are low capacitance SIDACtor(R) devices designed to protect broadband CPE equipment such as VoIP and DSL Modems from damaging overvoltage transients. The series provides a through-hole solution that enables CPE equipment to comply with global regulatory standards while limiting the impact to broadband signals. Features and Benefits t Low voltage overshoot Agency Approvals t Low on-state voltage Agency t Does not degrade with use Agency File Number E133083 t 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity t Fails short circuit when surged in excess of ratings Pinout Designation Applicable Global Standards Pin 1 Pin 3 Schematic Symbol t TIA-968-A t GR 1089 Intra-building t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building Electrical Characteristics Part Number P0080ECMCLxxx P0300ECMCLxxx P0640ECMCLxxx P0720ECMCLxxx P0900ECMCLxxx P1100ECMCLxxx P1300ECMCLxxx P1500ECMCLxxx P1800ECMCLxxx P2300ECMCLxxx P2600ECMCLxxx P3100ECMCLxxx P3500ECMCLxxx Marking P0080ECMC P0300ECMC P0640ECMC P0720ECMC P0900ECMC P1100ECMC P1300ECMC P1500ECMC P1800ECMC P2300ECMC P2600ECMC P3100ECMC P3500ECMC VDRM @lDRM=5A VS @100V/s V min V max 6 25 58 65 75 90 120 140 170 190 220 275 320 25 40 77 88 98 130 160 180 220 260 300 350 400 IH mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XXX Part Number Suffix: `AP' (Ammo Pack), or `RP1' or `RP2' (Reel Pack),. (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. IS 76 Revised: February 22, 2011 800 800 800 800 800 800 800 800 800 800 800 800 800 IT VT @IT=2.2 Amps Capacitance @1MHz, 2V bias A max V max pF min pF max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 35 25 55 50 45 45 40 35 35 30 30 30 25 75 45 85 75 70 70 60 55 50 50 45 45 40 SIDACtor (R) Protection Thyristors Broadband OptimizedTM Protection Series Surge Ratings IPP ITSM 50/60 Hz di/dt A min A min A/s Max 200 30 500 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 Value Unit C Notes: 1 Current waveform in s 2 Voltage waveform in s - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP $ - The device must initially be in thermal equilibrium with -40C < TJ < $ Thermal Considerations Package Symbol TO-92 Parameter TJ Operating Junction Temperature Range UP C TS Storage Temperature Range UP C 90 C/W R0JA Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform IPP - Peak Pulse Current - %IPP +I IT IS IH IDRM -V +V VT VDRM VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t - Time (s) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 IH 10 8 6 25 C 4 IH (TC = 25C) 12 Ratio of Percent of VS Change - % 14 2 0 -4 -6 1.8 1.6 1.4 25C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C Junction Temperature (TJ) - C (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 77 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors Broadband OptimizedTM Protection Soldering Parameters Pb-Free assembly (see Fig. 1) $ $ 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3C/sec. Max. TS(max) to TL - Ramp-up Rate 3C/sec. Max. Reflow - Temperature (TL) (Liquidus) Figure 1 TP $ - Temperature (tL) 60-150 secs. Peak Temp (TP) tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS $ 25 Time within 5C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6C/sec. Max. Time 25C to Peak Temp (TP) 8 min. Max. Do not exceed time to peak temperature (t 25C to peak) Time $ Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak $PS $ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling $UP $ NJOEXFMM VQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC $ 3) VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage $IST.*-45% .FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65C, 1008 hrs. Thermal Shock $UP $ NJOEXFMM TFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) $ 3) BUN VQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat $ TFDT.*-45% .FUIPE Body Material UL recognized epoxy meeting flammability classification 94V-0 Moisture Sensitivity Level Part Numbering 3) $ IST SFnPXDZDMFT $1FBL +&%&$+45% -FWFM Part Marking P xxx 0 E C MC L xxx TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE XXXXXXX XX PACKING OPTIONS RoHS COMPLIANT (Refer to Electrical Characteristics Table) Date Code XXXXX MC SERIES IPP RATING PACKAGE TYPE (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Part Marking Code 78 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors Broadband OptimizedTM Protection Packing Options Package Type Packing Options Quantity Description Added Suffix TO-92 Tape and Reel Pack E 2000 TO-92 Ammo Pack RP1 0.1 inch (2.54mm) 0.2 inch (5.08mm) AP (Not applicable) EIA-468-B N/A (Not applicable) N/A Dimensions -- TO-92 Inches B MT1/PIN 1 MT2/PIN 3 E D Max Min Max A 0.176 0.196 4.47 4.98 B 0.500 D 0.095 0.02 (0.5) 1.62 0.236 (41.2) (6.0) MAX 0.708 (18.0) 0.354 (9.0) 12.70 0.105 2.41 2.67 E 0.150 G 0.135 0.145 3.43 3.68 H 0.088 0.096 2.23 2.44 J 0.176 0.186 4.47 4.73 K 0.088 0.096 2.23 2.44 L 0.013 0.019 0.33 0.48 M 0.013 0.017 0.33 0.43 0.60 J The TO-92 is designed to meet mechanical standards as set forth in JEDEC publication number 95. 1.27 (32.2) 0.157 DIA (4.0) 0.20 (5.08) Flat down ed n of Fe Directio 25 Devices per fold 1.7 (43) 1.52 Dimensions are in inches (and millimeters). All leads are insulated from case. Case is electrically non-conductive. (Rated at 1600 V(AC) RMS for one minute from leads to case over the operating temperature range.) K 0.125 (3.2) MAX 0.50 (12.7) 3.81 N M L Min 0.25 (6.35) 0.50 (12.7) Millimeters G H EIA-481-D Ammo Pack Specification -- TO-92 Temperature Measurement Point N Industry Standard RP2 TO-92 Bulk Pack A Lead Spacing 6.9 (175) Mold flash shall not exceed 0.13 mm per side. 1.7 (43) 12.9 (327) Tape and Reel Specification -- TO-92 FLAT SIDE OF TO-92 A Inches A B C D W1 P P0 F(for RP1) F(for RP2) H H1 W W2 W3 W4 D W1 C B P H1 H W W3 ROUND SIDE OF TO-92 (RP1) W4 (RP2) W2 P0 (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. F F 79 Revised: February 22, 2011 Millimeters Min Max Min Max N/A 4.016 3.386 0.795 1.181 0.496 0.498 0.090 0.182 N/A N/A 0.674 0.354 0.236 0.020 14.173 N/A N/A N/A 1.968 0.504 0.502 0.110 0.244 1.673 1.270 0.763 0.370 N/A N/A N/A 102.0 86.0 20.2 30.0 12.60 12.65 2.29 4.63 N/A N/A 17.12 8.25 6.00 0.50 360.0 N/A N/A N/A 50.0 12.80 12.75 2.80 6.19 42.50 32.26 19.38 9.75 N/A N/A