Embedded Power for Business-Critical Continuity Rev.3.12.09_169 PTH12050 of 5 PTH12050 12 Vin Total Power: 33 Watts # of Outputs: Single Special Features * 6 A output current * 12 V input voltage * Wide-output voltage adjust 1.2 Vdc - 5.5 Vdc for suffix `W' & 0.8 Vdc - 1.8 Vdc for suffix `L' * Auto-trackTM sequencing* * Pre-bias start-up * Efficiencies up to 93% * Output ON/OFF inhibit * Output voltage sense * Point-of-Load-Alliance (POLA) compatible * Available RoHS compliant * 2 Year Warranty Specifications Input Input voltage range: (See Note 3, page 3) 10.8 - 13.2 Vdc Input current: No load 10 mA typ. Remote ON/OFF: (See Note 1, page 3) Positive logic Start-up time: 1 V/ms Undervoltage lockout: 8.8 - 0.4 V typ. Track input voltage: Pin 8 (See Note 6, page 3) 0.3 Vin All specifications are typical at nominal input, full load at 25C unless otherwise stated. Cin = 100 F, Cout = 0 F Safety * UL/cUL CAN/CSA-C22.2 No. 60950-1-03/UL 60950-1, File No. E174104 * TUV Product Service (EN60950) Certificate No. B 04 06 38572 044 * CB Report and Certificate to IEC60950, Certificate No. US/8292/UL *Auto-trackTM is a trade mark of Texas Instruments Embedded Power for Business-Critical Continuity Rev.3.12.09_169 PTH12050 of 5 Specifications Continued Output Voltage adjustability: (See Note 4, page 3) Suffix `W' Suffix `L' 1.2 - 5.5 Vdc 0.8 - 1.8 Vdc Setpoint accuracy: 2.0% Vo Line regulation: 5 mV typ. Load regulation: 5 mV typ. Total regulation: 3.0% Vo Minimum load: 0A Ripple and noise: 20 MHz bandwidth Temperature co-efficient: Transient response: Suffix `W' Vo 2.5 V Vo > 2.5 V Suffix `L' Vo 1.0 V Vo > 1.0 V 25 mV pk-pk 1% Vo -40 C to +85 C 0.5% Vo (See Note 5, page 3) 70 s recovery time Overshoot/undershoot 100 mV Margin adjustment: 20 mV pk-pk 30 mV pk-pk 5.0% Vo EMC Characteristics Electrostatic discharge: EN61000-4-2, IEC801-2 Conducted immunity: EN61000-4-6 Radiated immunity: EN61000-4-3 General Specifications Efficiency: See tables on page 3 Insulation voltage: Switching frequency: Over Vin and Io ranges Non-isolated Suffix `W' Suffix `L' 320 kHz typ. 250 kHz typ. Approvals and standards: EN60950 UL/cUL60950 Material flammability: UL94V-0 Dimensions: (L x W x H) Weight: MTBF: 22.10 x 12.57 x 8.50 mm 0.870 x 0.495 x 0.335 in 2.9 g (0.10 oz) Telcordia SR-332 7,092,000 hours Thermal Performance: (See Note 2, page 3) Operating ambient, temperature Non-operating -40 C to +85 C -40 C to +125 C MSL (`Z' suffix only): JEDEC J-STD-020C Level 3 Auto reset 14 A typ. Environmental Specifications Protection Short-circuit: Embedded Power for Business-Critical Continuity Rev.3.12.09_169 PTH12050 of 5 Ordering Information Output Power (max) Input Voltage Output Voltage 33 W 10.8 - 13.2 Vdc 33 W 10.8 - 13.2 Vdc Output Currents Min Max Efficiency (max) 0.8 - 1.8 Vdc 0A 6A 88% 5 mV 5 mV PTH12050L 1.2 - 5.5 Vdc 0A 6A 93% 5 mV 5 mV PTH12050W Part Number System with Options Regulation Line Load M odel Numbers (9, 10) PTH12050WAST Product Family Point of Load Alliance Compatible Input Voltage 12 = 12 V Output Current 05 = 6 A Mechanical Package Always 0 Packaging Options No Suffix = Trays T = Tape and Reel (7) Mounting Option (8) D = Horizontal Through-Hole (RoHS 6/6) H = Horizontal Through-Hole (RoHS 5/6) S = Surface-Mount Solder Ball (RoHS 5/6) Z = Surface-Mount Solder Ball (RoHS 6/6) Pin Option A = Through-Hole Std. Pin Length (0.140") A = Surface-Mount Tin/Lead Solder Ball Output Voltage Code W = Wide L = Low Voltage Output Voltage Adjustment of the PTH12050 Series The ultra-wide output voltage trim range offers major advantages to users who select the PTH12050. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 1.2 Vdc to 5.5 Vdc for suffix `W' and 0.8 Vdc to 1.8 Vdc for suffix `L'. When the PTH12050 converter leaves the factory the output has been adjusted to the default voltage of 1.2 V for the PTH12050W and 0.8 V for the PTH12050L. Notes Efficiency Table - PTH12050W (Io = 5 a) 1 Output Voltage Efficiency Vo = 5.0 V 93% Vo = 3.3 V 91% Vo = 2.5 V 89% Vo = 2.0 V 88% Vo = 1.8 V 87% Vo = 1.5 V 86% Vo = 1.2 V 84% Remote ON/OFF. Positive Logic ON: Pin 3 open; or V > Vin - 0.5 V OFF: Pin 3 GND; or V < 0.8 V (min - 0.2 V). 2 See Figure 1 for safe operating curve. 3 A 100 F electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimum of 750 mA rms of ripple current. C2 = 10 F ceramic capacitor, required for output voltages of 3.3 V and higher 4 An external output capacitor is not required for basic operation. Adding 100 F of distributed capacitance at the load will improve the transient response. 5 1 A/s load step, 50 to 100% Iomax, Cout = 100 F. 6 If utilized Vout will track applied voltage by 0.3 V (up to Vo set point). 7 Tape and reel packaging only available on the surface-mount versions. 8 The pk-pk output ripple voltage is measured with an external 10 F ceramic capacitor. See Figure 3 for Standard application schematic. 9 To order Pb-free (RoHS compatible) surface-mount parts replace the mounting option `S' with `Z', e.g. PTH12050WAZ. To order Pb-free (RoHS compatible) through-hole parts replace the mounting option `H' with `D', e.g. PTH12050WAD. 10 NOTICE: Some models do not support all options. Please contact your local Emerson Network Power representative or use the on-line model number search tool at http://www.PowerConversion.com to find a suitable alternative. Efficiency Table - PTH12050L (Io = 5 a) Output Voltage Efficiency Vo = 1.8 V 88% Vo = 1.5 V 87% Vo = 1.2 V 85% Vo = 1.0 V 83% Vo = 0.8 V 81% Embedded Power for Business-Critical Continuity Rev.3.12.09_169 PTH12050 of 5 Characteristic Data 80 100 70 95 90 EFFICIENCY (%) TEMPERATURE (C) 90 60 Nat Conv 100 LFM 50 200 LFM 400 LFM 40 80 75 20 1 2 3 4 5 2.0V 1.8V 1.5V 1.2V 70 65 60 30 0 Vout 5.0V 3.3V 2.5V 85 0 6 1 OUTPUT CURRENT (A) 5 6 100 80 90 70 60 EFFICIENCY (%) TEMPERATURE (C) 4 Figure 2 - Efficiency vs Load Current for PTH12050W Vin = 12 V (See Note B) 90 Nat Conv 100 LFM 50 40 30 20 0 1 2 3 4 5 70 60 50 6 Vout 6 2 3 4 5 6 Notes A 2 4 1 Figure 4 - Efficiency vs Load Current for PTH12050L Vin = 12 V (See Note B) Auto-track 3 0 OUTPUT CURRENT (A) Figure 3 - Safe Operating Area for PTH12050L Vin = 12 V, Output Voltage = 1.8 V (See Note A) 1 Vout 1.8V 1.5V 1.2V 1.0V 0.8V 80 OUTPUT CURRENT (A) PTH12050 (Top View) B 5 Cin 100F (Required) + Inhibit 3 OUTPUT CURRENT (A) Figure 1 - Safe Operating Area for PTH12050W Vin = 12 V, Output Voltage = 3.3 V (See Note A) Vin 2 + Cout 100F (Optional) RSET 0.5%, 0.1W (Required) GND GND Figure 5 - Standard Application - All Models SOA curves represent the conditions at which internal components are within the Emerson Network Power derating guidelines. Characteristic data has been developed from actual products tested at 25 C. This data is considered typical data for the converter. Embedded Power for Business-Critical Continuity Mechanical Drawings Americas 0.140 (3.55) 0.870 (22.10) 0.060 (1.52) 0.060 (1.52) 0.750 (19.06) 0.125 (3.18) 0.125 (3.18) 0.125 (3.18) 0.040 (1.02) 6 Places 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Europe (UK) 6 1 Rev.3.12.09_169 PTH12050 of 5 2 0.375 0.495 (12.57) (9.52) 3 Lowest Component 0.010 min. (0.25) Bottom side Clearance 5 4 0.070 (1.78) (Standoff Shoulder) TOP VIEW SIDE VIEW Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 Host Board 0.335 (8.50) MAX. Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 For global contact, visit: Figure 6 - Plated Through-Hole www.PowerConversion.com techsupport.embeddedpower @emerson.com 0.870 (22.10) 0.060 (1.52) 0.125 (3.18) 0.125 (3.18) 0.125 (3.18) 0.060 (1.52) 0.750 (19.06) 0.335 (8.50) max.* *After solder reflow on customer board 6 1 2 Solder Ball 0.040 (1.02) 6 Places 0.495 0.375 (12.57) (9.52) 3 While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power 5 4 Connectivity SIDE VIEW TOP VIEW DC Power Embedded Computing Embedded Power Monitoring Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) Pin Connections Pin No. Function Pin 1 Ground Pin 2 Track Pin 3 Vin Pin 4 Inhibit* Pin 5 Vo adjust Pin 6 Vout Outside Plant Power Switching & Controls Figure 7 - Surface-Mount Precision Cooling Racks & Integrated Cabinets Services Surge Protection *Denotes negative logic: Open = Normal operation Ground = Function active EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. (c)2008 Emerson Electric Co.