Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC688LP4 / 688LP4E v01.1010 MIXERS - SINGLE & DOUBLE BALANCED - SMT 10 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 2.0 - 2.7 GHz Typical Applications Features The HMC688LP4(E) is Ideal for: High Input IP3: +35 dBm * Cellular/3G & LTE/WiMAX/4G Low Conversion Loss: 7.5 dB * Basestations & Repeaters Low LO Drive: 0 dBm * GSM, CDMA & OFDM Optimized for Low Side LO Input * Transmitters and Receivers Upconversion & Downconversion Applications 24 Lead 4x4mm SMT Package: 16mm2 Functional Diagram General Description The HMC688LP4(E) is a high dynamic range passive MMIC mixer with integrated LO amplifier in a 4x4 SMT QFN package covering 2.0 to 2.7 GHz. Excellent input IP3 performance of +35 dBm for down conversion is provided for 3G & 4G GSM/CDMA applications at an LO drive of 0 dBm. With an input 1 dB compression of +25 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 7.5 dB typical. The DC to 700 MHz IF frequency response will satisfy GSM/CDMA transmit or receive frequency plans. The HMC688LP4(E) is pin for pin compatible with the HMC689LP4(E) which is a 2.0 - 2.7 GHz mixer with LO amplifier optimized for high side LO applications. Electrical Specifications, TA = +25 C, IF = 300 MHz, LO = 0 dBm, Vcc = Vcc1, 2, 3 = +5V, G_Bias = +2.5V* Parameter Min. Frequency Range, RF Typ. Max. 2.0 - 2.7 Units GHz Frequency Range, LO 1.7 - 2.4 GHz Frequency Range, IF DC - 700 MHz Conversion Loss 7.5 Noise Figure (SSB) 10 dB 8 dB LO to RF Isolation 16 25 dB LO to IF Isolation 20 27 dB RF to IF Isolation 25 34 dB IP3 (Input) 35 dBm 1 dB Compression (Input) 25 dBm LO Drive Input Level (Typical) -9 to +3 Supply Current Icc total 140 dBm 168 mA * Unless otherwise noted all measurements performed as downconverter with low side LO & IF = 300 MHz. 10 - 1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC688LP4 / 688LP4E v01.1010 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 2.0 - 2.7 GHz Isolation Conversion Gain vs. Temperature 0 RF/IF LO/RF LO/IF -10 -10 +25 C +85 C -40 C -15 -30 -40 -50 -20 2 2.2 2.4 2.6 2.8 2 3 2.2 2.4 2.6 2.8 3 FREQUENCY (GHz) FREQUENCY (GHz) Return Loss Conversion Gain vs. LO Drive 0 0 RF LO -5 -5 RETURN LOSS (dB) CONVERSION GAIN (dB) 10 -20 -10 -9 dBm -6 dBm -3 dBm 0 dBm +3 dBm -15 2.2 2.4 -15 -20 -25 1.6 -20 2 -10 2.6 2.8 3 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 FREQUENCY (GHz) FREQUENCY (GHz) IF Bandwidth (LO= 2.1 GHz) Input P1dB vs. Temperature 0 30 25 -10 P1dB (dBm) RESPONSE (dB) -5 -15 -20 -25 +25 C +85 C -40 C 15 IF Return Loss Conversion Gain -30 -35 0.1 20 MIXERS - SINGLE & DOUBLE BALANCED - SMT -5 ISOLATION (dB) CONVERSION GAIN (dB) 0 10 0.2 0.3 0.4 0.5 0.6 FREQUENCY (GHz) 0.7 0.8 0.9 2 2.2 2.4 2.6 2.8 3 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 2 HMC688LP4 / 688LP4E v01.1010 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 2.0 - 2.7 GHz Input IP3 vs. LO Drive [1] 40 35 35 IP3 (dBm) 40 30 +25 C +85 C -40 C 25 -9 dBm -6 dBm -3 dBm 0 dBm +3 dBm 20 2 2.2 2.4 2.6 2.8 3 2 2.2 FREQUENCY (GHz) +2RF -2LO Response vs. Temperature [2] 2.6 2.8 3 +2RF -2LO Response vs. LO Drive [2] 100 90 +2RF-2LO RESPONSE (dBc) 100 +2RF-2LO RESPONSE (dBc) 2.4 FREQUENCY (GHz) +25 C +85 C -40 C 80 70 60 50 40 -9 dBm -6 dBm -3 dBm 0 dBm +3 dBm 90 80 70 60 50 40 2 2.2 2.4 2.6 2.8 2 2.2 FREQUENCY (GHz) 2.4 2.6 2.8 FREQUENCY (GHz) +3RF -3LO Response vs. Temperature [2] +3RF -3LO Response vs. LO Drive [2] 90 +3RF-3LO RESPONSE (dBc) 90 +25 C +85 C -40 C 85 80 75 70 65 85 -9 dBm -6 dBm -3 dBm 0 dBm +3 dBm 80 75 70 65 2 2.2 2.4 2.6 2.8 FREQUENCY (GHz) [1] Two-tone input power = +9 dBm each tone, 1 MHz spacing. 10 - 3 30 25 20 +3RF-3LO RESPONSE (dBc) MIXERS - SINGLE & DOUBLE BALANCED - SMT 10 IP3 (dBm) Input IP3 vs. Temperature [1] 2 2.2 2.4 2.6 2.8 FREQUENCY (GHz) [2] Referenced to RF Input Power at 0 dBm. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC688LP4 / 688LP4E v01.1010 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 2.0 - 2.7 GHz Upconverter Performance Input IP3 vs. LO Drive [1] 40 -5 35 -10 -9 dBm -6 dBm -3 dBm 0 dBm +3 dBm -15 10 30 -3 dBm 0 dBm +3 dBm 25 -20 20 2 2.2 2.4 2.6 2.8 3 2 2.2 FREQUENCY (GHz) 2.4 2.6 2.8 3 FREQUENCY (GHz) Absolute Maximum Ratings MxN Spurious @ IF Port RF / IF Input (Vcc1, 2, 3 = +5V) +23 dBm LO Drive (Vcc1, 2, 3 = +5V) +10 dBm Vcc1, 2, 3 Channel Temperature nLO mRF 0 1 2 3 4 +5.5V 0 xx 20 26 52 30 125 C 1 28 0 41 22 66 2 78 68 63 64 68 3 115 93 99 76 95 4 129 >133 >133 120 121 Continuous Pdiss (T = 85C) (derate 36.23 mW/C above 85C) 1.45 W Thermal Resistance (channel to ground paddle) 27.6 C/W Storage Temperature -65 to 150 C Operating Temperature -40 to +85 C RF Freq. = 2.5 GHz @ 0 dBm LO Freq. = 2.2 GHz @ 0 dBm All values in dBc below IF power level (1RF - 1LO). ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Typical Supply Current vs. Vcc Vcc1, 2, 3 (V) Icc total (mA) Harmonics of LO nLO Spur @ RF Port 4.75 130 LO Freq. (GHz) 1 2 3 4 5.00 140 1.8 26 29 51 24 5.25 150 Downconverter will operate over full voltage range shown above. [1] Two-tone input power = +9 dBm each tone, 1 MHz spacing. 1.9 24 27 46 27 2.0 22 23 55 27 2.1 21 20 38 23 2.2 22 19 34 22 2.3 22 18 36 21 2.4 24 17 39 22 2.5 26 16 39 25 2.6 27 16 39 29 2.7 28 18 37 30 MIXERS - SINGLE & DOUBLE BALANCED - SMT 0 IP3 (dBm) CONVERSION GAIN (dB) Upconverter Performance Conversion Gain vs. LO Drive LO = 0 dBm All values in dBc below input LO level measured at RF port. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 4 HMC688LP4 / 688LP4E v01.1010 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 2.0 - 2.7 GHz Outline Drawing MIXERS - SINGLE & DOUBLE BALANCED - SMT 10 10 - 5 NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY. 3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN. 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 6. PAD BURR LENGTH SHALL BE 0.15mm MAX. PAD BURR HEIGHT SHALL BE 0.25mm MAX. 7. PACKAGE WARP SHALL NOT EXCEED 0.05mm 8. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 9. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC688LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC688LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H688 XXXX H688 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC688LP4 / 688LP4E v01.1010 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 2.0 - 2.7 GHz Pin Descriptions Pin Number Description N/C No connection. These pins may be connected to RF ground. Performance will not be affected. 2, 5, 15, 17 GND Package bottom must be connected to RF/DC ground. 3 RF This pin is matched single-ended 50 Ohm and DC shorted to ground through a balun. 4 TAP Center tap of secondary side of the internal RF balun. Short to ground with a zero ohms close to the IC. 8, 10, 24 Vcc1, Vcc2, Vcc3 Power supply voltage. See application circuit for required external components. 9 LO_BIAS Adjust the LO buffer current through an external resistor. See application circuit for required external components. 16 LO This pin is matched single-ended 50 Ohm and DC shorted to ground through a balun. 19 G_BIAS External optional bias. See application circuit for required external components. Apply +2.5V for nominal performance. 21, 22 IFN, IFP Differential IF input / output pins matched to differential 50 Ohms. For applications not requiring operation to DC an off chip DC blocking capacitor should be used. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 MIXERS - SINGLE & DOUBLE BALANCED - SMT Function 1, 6, 7, 11 - 14, 18, 20, 23 10 - 6 HMC688LP4 / 688LP4E v01.1010 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 2.0 - 2.7 GHz Evaluation PCB MIXERS - SINGLE & DOUBLE BALANCED - SMT 10 List of Materials for Evaluation PCB 120974 [1] Item Description J1 - J3 SMA Connector J4 - J7 DC Pin C1 1.8 pF Capacitor, 0402 Pkg. C4 1.5 pF Capacitor, 0402 Pkg. C7, C8 10 nF Capacitor, 0402 Pkg. C10, C12, C16, C18 1 nF Capacitor, 0402 Pkg. C11, C15, C17, C21 0.1 F Capacitor, 0402 Pkg. C19 22 pF Capacitor, 0402 Pkg. C20 4.7 F Case A, Tantalum L1 7.5 nH Inductor, 0402 Pkg. L2 10 nH Inductor, 0402 Pkg. R2 - R4 0 Ohm Resistor, 0402 Pkg. R9 243 Ohm Resistor, 0603 Pkg. T1 1:1 Transformer - M/A-COM MABACT0039 U1 HMC688LP4(E) Downconverter PCB [2] 118162 Evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25R, FR4 10 - 7 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC688LP4 / 688LP4E v01.1010 BiCMOS MMIC MIXER W/ INTEGRATED LO AMPLIFIER, 2.0 - 2.7 GHz Application Circuit MIXERS - SINGLE & DOUBLE BALANCED - SMT 10 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 8 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC688LP4E HMC688LP4ETR 119915-HMC688LP4