0 Spartan-IIE FPGA Family Data Sheet R DS077 June 18, 2008 0 0 Product Specification This document includes all four modules of the Spartan(R)-IIE FPGA data sheet. Module 1: Introduction and Ordering Information Module 3: DC and Switching Characteristics DS077-1 (v2.3) June 18, 2008 DS077-3 (v2.3) June 18, 2008 * * * * * * * Introduction Features General Overview Product Availability User I/O Chart Ordering Information * Module 2: Functional Description DS077-2 (v2.3) June 18, 2008 * * * Architectural Description - Spartan-IIE Array - Input/Output Block - Configurable Logic Block - Block RAM - Clock Distribution: Delay-Locked Loop - Boundary Scan Development System Configuration DC Specifications - Absolute Maximum Ratings - Recommended Operating Conditions - DC Characteristics - Power-On Requirements - DC Input and Output Levels Switching Characteristics - Pin-to-Pin Parameters - IOB Switching Characteristics - Clock Distribution Characteristics - DLL Timing Parameters - CLB Switching Characteristics - Block RAM Switching Characteristics - TBUF Switching Characteristics - JTAG Switching Characteristics - Configuration Switching Characteristics Module 4: Pinout Tables DS077-4 (2.3) June 18, 2008 * * Pin Definitions Pinout Tables IMPORTANT NOTE: The Spartan-IIE FPGA data sheet is in four modules. Each module has its own Revision History at the end. Use the PDF "Bookmarks" for easy navigation in this volume. (c) 2003-2008 Xilinx, Inc. All rights reserved. XILINX, the Xilinx logo, the Brand Window, and other designated brands included herein are trademarks of Xilinx, Inc. All other trademarks are the property of their respective owners. DS077 June 18, 2008 Product Specification www.xilinx.com 1 R 2 www.xilinx.com DS077 June 18, 2008 Product Specification Spartan-IIE FPGA Family: Introduction and Ordering Information R DS077-1 (v2.3) June 18, 2008 0 Product Specification Introduction The Spartan(R)-IIE Field-Programmable Gate Array family gives users high performance, abundant logic resources, and a rich feature set, all at an exceptionally low price. The seven-member family offers densities ranging from 50,000 to 600,000 system gates, as shown in Table 1. System performance is supported beyond 200 MHz. Features include block RAM (to 288K bits), distributed RAM (to 221,184 bits), 19 selectable I/O standards, and four DLLs (Delay-Locked Loops). Fast, predictable interconnect means that successive design iterations continue to meet timing requirements. The Spartan-IIE family is a superior alternative to mask-programmed ASICs. The FPGA avoids the initial cost, lengthy development cycles, and inherent risk of conventional ASICs. Also, FPGA programmability permits design upgrades in the field with no hardware replacement necessary (impossible with ASICs). * Features * * Second generation ASIC replacement technology - Densities as high as 15,552 logic cells with up to 600,000 system gates - Streamlined features based on Virtex(R)-E FPGA architecture - Unlimited in-system reprogrammability - Very low cost - Cost-effective 0.15 micron technology System level features - SelectRAMTM hierarchical memory: * 16 bits/LUT distributed RAM * Configurable 4K-bit true dual-port block RAM * Fast interfaces to external RAM Fully 3.3V PCI compliant to 64 bits at 66 MHz and CardBus compliant - Low-power segmented routing architecture - Dedicated carry logic for high-speed arithmetic - Efficient multiplier support - Cascade chain for wide-input functions - Abundant registers/latches with enable, set, reset - Four dedicated DLLs for advanced clock control * Eliminate clock distribution delay * Multiply, divide, or phase shift - Four primary low-skew global clock distribution nets - IEEE 1149.1 compatible boundary scan logic Versatile I/O and packaging - Pb-free package options - Low-cost packages available in all densities - Family footprint compatibility in common packages - 19 high-performance interface standards * LVTTL, LVCMOS, HSTL, SSTL, AGP, CTT, GTL * LVDS and LVPECL differential I/O - Up to 205 differential I/O pairs that can be input, output, or bidirectional - Hot swap I/O (CompactPCI friendly) Core logic powered at 1.8V and I/Os powered at 1.5V, 2.5V, or 3.3V - * * Fully supported by powerful Xilinx(R) ISE(R) development system - Fully automatic mapping, placement, and routing - Integrated with design entry and verification tools - Extensive IP library including DSP functions and soft processors Table 1: Spartan-IIE FPGA Family Members Device Logic Cells Typical System Gate Range (Logic and RAM) CLB Array (R x C) Total CLBs Maximum Available User I/O(1) Maximum Differential I/O Pairs Distributed RAM Bits Block RAM Bits XC2S50E 1,728 23,000 - 50,000 16 x 24 384 182 83 24,576 32K XC2S100E 2,700 37,000 - 100,000 20 x 30 600 202 86 38,400 40K XC2S150E 3,888 52,000 - 150,000 24 x 36 864 265 114 55,296 48K XC2S200E 5,292 71,000 - 200,000 28 x 42 1,176 289 120 75,264 56K XC2S300E 6,912 93,000 - 300,000 32 x 48 1,536 329 120 98,304 64K XC2S400E 10,800 145,000 - 400,000 40 x 60 2,400 410 172 153,600 160K XC2S600E 15,552 210,000 - 600,000 48 x 72 3,456 514 205 221,184 288K Notes: 1. User I/O counts include the four global clock/user input pins. See details in Table 2, page 5 (c) 2003-2008 Xilinx, Inc. All rights reserved. XILINX, the Xilinx logo, the Brand Window, and other designated brands included herein are trademarks of Xilinx, Inc. All other trademarks are the property of their respective owners. DS077-1 (v2.3) June 18, 2008 Product Specification www.xilinx.com 3 R Spartan-IIE FPGA Family: Introduction and Ordering Information General Overview The Spartan-IIE family of FPGAs have a regular, flexible, programmable architecture of Configurable Logic Blocks (CLBs), surrounded by a perimeter of programmable Input/Output Blocks (IOBs). There are four Delay-Locked Loops (DLLs), one at each corner of the die. Two columns of block RAM lie on opposite sides of the die, between the CLBs and the IOB columns. The XC2S400E has four columns and the XC2S600E has six columns of block RAM. These functional elements are interconnected by a powerful hierarchy of versatile routing channels (see Figure 1). Spartan-IIE FPGAs are customized by loading configuration data into internal static memory cells. Unlimited reprogramming cycles are possible with this approach. Stored values in these cells determine logic functions and interconnections implemented in the FPGA. Configuration data can be read from an external serial PROM (master serial mode), or written into the FPGA in slave serial, slave parallel, or Boundary Scan modes. Xilinx offers multiple types of low-cost configuration solutions including the Platform Flash in-system programmable configuration PROMs. Spartan-IIE FPGAs are typically used in high-volume applications where the versatility of a fast programmable solution adds benefits. Spartan-IIE FPGAs are ideal for shortening product development cycles while offering a cost-effective solution for high volume production. Spartan-IIE FPGAs achieve high-performance, low-cost operation through advanced architecture and semiconductor technology. Spartan-IIE devices provide system clock rates beyond 200 MHz. In addition to the conventional benefits of high-volume programmable logic solutions, Spartan-IIE FPGAs also offer on-chip synchronous single-port and dual-port RAM (block and distributed form), DLL clock drivers, programmable set and reset on all flip-flops, fast carry logic, and many other features. Spartan-IIE Family Compared to Spartan-II Family * * * * * * * Higher density and more I/O Higher performance Unique pinouts in cost-effective packages Differential signaling - LVDS, Bus LVDS, LVPECL VCCINT = 1.8V - Lower power - 5V tolerance with external resistor - 3V tolerance directly PCI, LVTTL, and LVCMOS2 input buffers powered by VCCO instead of VCCINT Unique larger bitstream DLL BLOCK RAM CLBs CLBs BLOCK RAM BLOCK RAM CLBs CLBs BLOCK RAM DLL DLL DLL I/O LOGIC DS077_01_052102 Figure 1: Basic Spartan-IIE Family FPGA Block Diagram 4 www.xilinx.com DS077-1 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Introduction and Ordering Information Spartan-IIE Product Availability Table 2 shows the maximum user I/Os available on the device and the number of user I/Os available for each device/package combination. Table 2: Spartan-IIE FPGA User I/O Chart Available User I/O According to Package Type Device Maximum User I/O TQ144 TQG144 PQ208 PQG208 FT256 FTG256 FG456 FGG456 FG676 FGG676 XC2S50E 182 102 146 182 - - XC2S100E 202 102 146 182 202 - XC2S150E 265 - 146 182 265 - XC2S200E 289 - 146 182 289 - XC2S300E 329 - 146 182 329 - XC2S400E 410 - - 182 329 410 XC2S600E 514 - - - 329 514 Notes: 1. User I/O counts include the four global clock/user input pins. DS077-1 (v2.3) June 18, 2008 Product Specification www.xilinx.com 5 R Spartan-IIE FPGA Family: Introduction and Ordering Information Ordering Information Spartan-IIE devices are available in both standard and Pb-free packaging options for all device/package combinations. The Pb-free packages include a special "G" character in the ordering code. Standard Packaging Example: XC2S50E -6 PQ 208 C Device Type Temperature Range Speed Grade Number of Pins Package Type DS077-1_03a_072004 Pb-Free Packaging Example: XC2S50E -6 PQ G 208 C Device Type Temperature Range Speed Grade Number of Pins Package Type Pb-free DS077-1_03b_072004 Device Ordering Options Device Speed Grade XC2S50E -6 Standard Performance XC2S100E Performance(1) -7 Higher Package Type / Number of Pins Temperature Range ( TJ )(2) TQ(G)144 144-pin Plastic Thin QFP C = Commercial PQ(G)208 208-pin Plastic QFP I = Industrial XC2S150E FT(G)256 256-ball Fine Pitch BGA XC2S200E FG(G)456 456-ball Fine Pitch BGA XC2S300E FG(G)676 676-ball Fine Pitch BGA 0C to + 85C - 40C to +100C XC2S400E XC2S600E Notes: 1. The -7 speed grade is exclusively available in the Commercial temperature range. 2. See www.xilinx.com for information on automotive temperature range devices. Device Part Marking Figure 2 is a top marking example for Spartan-IIE FPGAs in the quad-flat packages. The markings for BGA packages are nearly identical to those for the quad-flat packages, except that the marking is rotated with respect to the ball A1 indicator. The "7C" and "6I" Speed Grade/Temperature Range part combinations may be dual marked as "7C/6I". Devices with the dual mark can be used as either -7C or -6I devices. Devices with a single mark are only guaranteed for the marked speed grade and temperature range. R R Device Type Package Speed SPARTAN XC2S50E PQ208xxx0425 xxxxxxxxx 6C Date Code Lot Code (numeric) Operating Range Sample package with part marking for XC2S50E-6PQ208C. Figure 2: Spartan-IIE QFP Marking Example 6 www.xilinx.com DS077-1 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Introduction and Ordering Information Revision History Date Version No. 06/27/02 1.1 Updated -7 availability. 11/18/02 2.0 Added XC2S400E and XC2S600E. Corrected XC2S150E max I/O count and XC2S50E differential I/O count and updated availability. 07/09/03 2.1 Noted hot-swap capability. Updated Table 2 to show that all products are available. Clarified device part marking. 07/28/04 2.2 Added information on Pb-free packaging options. 06/18/08 2.3 Added dual mark information in Device Part Marking. Updated all modules for continuous page, figure, and table numbering. Updated links. Synchronized all modules to v2.3. DS077-1 (v2.3) June 18, 2008 Product Specification Description www.xilinx.com 7 Spartan-IIE FPGA Family: Introduction and Ordering Information 8 www.xilinx.com R DS077-1 (v2.3) June 18, 2008 Product Specification Spartan-IIE FPGA Family: Functional Description R DS077-2 (v2.3) June 18, 2008 0 Architectural Description Spartan-IIE FPGA Array The Spartan(R)-IIE user-programmable gate array, shown in Figure 3, is composed of five major configurable elements: * * * * * IOBs provide the interface between the package pins and the internal logic CLBs provide the functional elements for constructing most logic Dedicated block RAM memories of 4096 bits each Clock DLLs for clock-distribution delay compensation and clock domain control Versatile multi-level interconnect structure Product Specification As can be seen in Figure 3, the CLBs form the central logic structure with easy access to all support and routing structures. The IOBs are located around all the logic and memory elements for easy and quick routing of signals on and off the chip. Values stored in static memory cells control all the configurable logic elements and interconnect resources. These values load into the memory cells on power-up, and can reload if necessary to change the function of the device. Each of these elements will be discussed in detail in the following sections. DLL BLOCK RAM CLBs CLBs BLOCK RAM BLOCK RAM CLBs CLBs BLOCK RAM DLL DLL DLL I/O LOGIC DS077_01_052102 Figure 3: Basic Spartan-IIE Family FPGA Block Diagram (c) 2003-2007 Xilinx, Inc. All rights reserved. XILINX, the Xilinx logo, the Brand Window, and other designated brands included herein are trademarks of Xilinx, Inc. All other trademarks are the property of their respective owners. DS077-2 (v2.3) June 18, 2008 Product Specification www.xilinx.com 9 R Spartan-IIE FPGA Family: Functional Description T SR D VCCO Q Package Pin TFF CLK CK TCE EC VCC OE SR I/O Programmable Bias and ESD Network Package Pin SR O D Q Programmable Output Buffer OFF CK OCE VCC(1) EC Internal Reference Programmable Delay IQ I/O, VREF SR I D Package Pin Programmable Input Buffer Q IFF CK ICE To Next I/O To Other External VREF Inputs of Bank EC Notes: 1. For some I/O standards. DS077-2_01_051501 Figure 4: Spartan-IIE Input/Output Block (IOB) Table 3: Standards Supported by I/O (Typical Values) I/O Standard Input Output Board Reference Input Source Termination Voltage Voltage Voltage Voltage (VREF) (VTT) (VCCO) (VCCO) LVTTL (2-24 mA) N/A 3.3 3.3 N/A LVCMOS2 N/A 2.5 2.5 N/A LVCMOS18 N/A 1.8 1.8 N/A PCI (3V, 33 MHz/66 MHz) N/A 3.3 3.3 N/A GTL 0.8 N/A N/A 1.2 GTL+ 1.0 N/A N/A 1.5 HSTL Class I 0.75 N/A 1.5 0.75 HSTL Class III 0.9 N/A 1.5 1.5 HSTL Class IV 0.9 N/A 1.5 1.5 SSTL3 Class I and II 1.5 N/A 3.3 1.5 SSTL2 Class I and II 1.25 N/A 2.5 1.25 CTT 1.5 N/A 3.3 1.5 AGP 1.32 N/A 3.3 N/A LVDS, Bus LVDS N/A N/A 2.5 N/A LVPECL N/A N/A 3.3 N/A 10 Input/Output Block The Spartan-IIE FPGA IOB, as seen in Figure 4, features inputs and outputs that support a wide variety of I/O signaling standards. These high-speed inputs and outputs are capable of supporting various state of the art memory and bus interfaces. The default standard is LVTTL. Table 3 lists several of the standards which are supported along with the required reference (VREF), output (VCCO) and board termination (VTT) voltages needed to meet the standard. For more details on the I/O standards and termination application examples, see XAPP179, "Using SelectIO Interfaces in Spartan-II and Spartan-IIE FPGAs." The three IOB registers function either as edge-triggered D-type flip-flops or as level-sensitive latches. Each IOB has a clock signal (CLK) shared by the three registers and independent Clock Enable (CE) signals for each register. In addition to the CLK and CE control signals, the three registers share a Set/Reset (SR). For each register, this signal can be independently configured as a synchronous Set, a synchronous Reset, an asynchronous Preset, or an asynchronous Clear. A feature not shown in the block diagram, but controlled by the software, is polarity control. The input and output buffers and all of the IOB control signals have independent polarity controls. www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description All Spartan-IIE FPGA IOBs support IEEE 1149.1-compatible boundary scan testing. Input Path A buffer in the IOB input path routes the input signal directly to internal logic and through an optional input flip-flop. An optional delay element at the D-input of this flip-flop eliminates pad-to-pad hold time. The delay is matched to the internal clock-distribution delay of the FPGA, and when used, assures that the pad-to-pad hold time is zero. Each input buffer can be configured to conform to any of the low-voltage signaling standards supported. In some of these standards the input buffer utilizes a user-supplied threshold voltage, VREF. The need to supply VREF imposes constraints on which standards can used in close proximity to each other. See I/O Banking. An optional weak-keeper circuit is connected to each output. When selected, the circuit monitors the voltage on the pad and weakly drives the pin High or Low to match the input signal. If the pin is connected to a multiple-source signal, the weak keeper holds the signal in its last state if all drivers are disabled. Maintaining a valid logic level in this way helps eliminate bus chatter. Because the weak-keeper circuit uses the IOB input buffer to monitor the input level, an appropriate VREF voltage must be provided if the signaling standard requires one. The provision of this voltage must comply with the I/O banking rules. I/O Banking Some of the I/O standards described above require VCCO and/or VREF voltages. These voltages are externally supplied and connected to device pins that serve groups of IOBs, called banks. Consequently, restrictions exist about which I/O standards can be combined within a given bank. Eight I/O banks result from separating each edge of the FPGA into two banks (see Figure 5). The pinout tables show the bank affiliation of each I/O (see Pinout Tables, page 53). Each bank has multiple VCCO pins which must be connected to the same voltage. Voltage requirements are determined by the output standards in use. Bank 0 There are optional pull-up and pull-down resistors at each input for use after configuration. Bank 1 GCLK3 Bank 2 All pads are protected against damage from electrostatic discharge (ESD) and from over-voltage transients. After configuration, clamping diodes are connected to VCCO for LVTTL, PCI, HSTL, SSTL, CTT, and AGP standards. can be used in close proximity to each other. See I/O Banking. Bank 7 Optional pull-up and pull-down resistors and an optional weak-keeper circuit are attached to each user I/O pad. Prior to configuration all outputs not involved in configuration are forced into their high-impedance state. The pull-down resistors and the weak-keeper circuits are inactive, but inputs may optionally be pulled up. The activation of pull-up resistors prior to configuration is controlled on a global basis by the configuration mode pins. If the pull-up resistors are not activated, all the pins will float. Consequently, external pull-up or pull-down resistors must be provided on pins required to be at a well-defined logic level prior to configuration. GCLK2 Bank 6 The output path includes a 3-state output buffer that drives the output signal onto the pad. The output signal can be routed to the buffer directly from the internal logic or through an optional IOB output flip-flop. The 3-state control of the output can also be routed directly from the internal logic or through a flip-flip that provides synchronous enable and disable. GCLK1 Bank 5 Bank 3 Spartan-IIE Device Output Path GCLK0 Bank 4 DS077-2_02_051501 Each output driver can be individually programmed for a wide range of low-voltage signaling standards. Each output buffer can source up to 24 mA and sink up to 48 mA. Drive strength and slew rate controls minimize bus transients. The default output driver is LVTTL with 12 mA drive strength and slow slew rate. In most signaling standards, the output high voltage depends on an externally supplied VCCO voltage. The need to supply VCCO imposes constraints on which standards DS077-2 (v2.3) June 18, 2008 Product Specification Figure 5: Spartan-IIE I/O Banks In the TQ144 and PQ208 packages, the eight banks have VCCO connected together. Thus, only one VCCO level is allowed in these packages, although different VREF values are allowed in each of the eight banks. Within a bank, standards may be mixed only if they use the same VCCO. Compatible standards are shown in Table 4. GTL and GTL+ appear under all voltages because their open-drain outputs do not depend on VCCO. Note that VCCO www.xilinx.com 11 R Spartan-IIE FPGA Family: Functional Description is required for most output standards and for LVTTL, LVCMOS, and PCI inputs. Table 4: Compatible Standards VCCO Compatible Standards 3.3V PCI, LVTTL, SSTL3 I, SSTL3 II, CTT, AGP, LVPECL, GTL, GTL+ 2.5V SSTL2 I, SSTL2 II, LVCMOS2, LVDS, Bus LVDS, GTL, GTL+ 1.8V LVCMOS18, GTL, GTL+ 1.5V HSTL I, HSTL III, HSTL IV, GTL, GTL+ Hot Swap, Hot Insertion, Hot Socketing Support The I/O pins support hot swap -- also called hot insertion and hot socketing -- and are considered CompactPCI Friendly according to the PCI Bus v2.2 Specification. Consequently, an unpowered Spartan-IIE FPGA can be plugged directly into a powered system or backplane without affecting or damaging the system or the FPGA. The hot swap functionality is built into every XC2S150E, XC2S400E, and XC2S600E device. All other Spartan-IIE devices built after Product Change Notice PCN2002-05 also include hot swap functionality. To support hot swap, Spartan-IIE devices include the following I/O features. Some input standards require a user-supplied threshold voltage, VREF. In this case, certain user-I/O pins are automatically configured as inputs for the VREF voltage. About one in six of the I/O pins in the bank assume this role. * * VREF pins within a bank are interconnected internally and consequently only one VREF voltage can be used within each bank. All VREF pins in the bank, however, must be connected to the external voltage source for correct operation. In a bank, inputs requiring VREF can be mixed with those that do not but only one VREF voltage may be used within a bank. The VCCO and VREF pins for each bank appear in the device pinout tables. Within a given package, the number of VREF and VCCO pins can vary depending on the size of device. In larger devices, more I/O pins convert to VREF pins. Since these are always a superset of the VREF pins used for smaller devices, it is possible to design a PCB that permits migration to a larger device. All VREF pins for the largest device anticipated must be connected to the VREF voltage, and not used for I/O. Table 5: I/O Banking TQ144, PQ208 FT256, FG456, FG676 VCCO Banks Interconnected as 1 8 independent VREF Banks 8 independent 8 independent Package See Xilinx(R) Application Note XAPP179 for more information on I/O resources. 12 * * Signals can be applied to Spartan-IIE FPGA I/O pins before powering the FPGA's VCCINT or VCCO supply inputs. Spartan-IIE FPGA I/O pins are high-impedance (i.e., three-stated) before and throughout the power-up and configuration processes when employing a configuration mode that does not enable the preconfiguration weak pull-up resistors (see Table 11, page 22). There is no current path from the I/O pin back to the VCCINT or VCCO voltage supplies. Spartan-IIE FPGAs are immune to latch-up during hot swap. Once connected to the system, each pin adds a small amount of capacitance (CIN). Likewise, each I/O consumes a small amount of DC current, equivalent to the input leakage specification (IL). There also may be a small amount of temporary AC current (IHSPO) when the pin input voltage exceeds VCCO plus 0.4V, which lasts less than 10 ns. A weak-keeper circuit within each user-I/O pin is enabled during the last frame of configuration data and has no noticeable effect on robust system signals driven by an active driver or a strong pull-up or pull-down resistor. Undriven or floating system signals may be affected. The specific effect depends on how the I/O pin is configured. User-I/O pins configured as outputs or enabled outputs have a weak pull-up resistor to VCCO during the last configuration frame. User-I/O pins configured as inputs or bidirectional I/Os have weak pull-down resistors. The weak-keeper circuit turns off when the DONE pin goes High, provided that it is not used in the configured application. www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description Configurable Logic Block The basic building block of the Spartan-IIE FPGA CLB is the logic cell (LC). An LC includes a 4-input function generator, carry logic, and storage element. The output from the function generator in each LC drives the CLB output or the D input of the flip-flop. Each Spartan-IIE FPGA CLB contains four LCs, organized in two similar slices; a single slice is shown in Figure 6. In addition to the four basic LCs, the Spartan-IIE FPGA CLB contains logic that combines function generators to provide functions of five or six inputs. Look-Up Tables Spartan-IIE FPGA function generators are implemented as 4-input look-up tables (LUTs). In addition to operating as a function generator, each LUT can provide a 16 x 1-bit synchronous RAM. Furthermore, the two LUTs within a slice can be combined to create a 16 x 2-bit or 32 x 1-bit synchronous RAM, or a 16 x 1-bit dual-port synchronous RAM. DS077-2 (v2.3) June 18, 2008 Product Specification The Spartan-IIE FPGA LUT can also provide a 16-bit shift register that is ideal for capturing high-speed or burst-mode data. This mode can also be used to store data in applications such as Digital Signal Processing. Storage Elements Storage elements in the Spartan-IIE FPGA slice can be configured either as edge-triggered D-type flip-flops or as level-sensitive latches. The D inputs can be driven either by function generators within the slice or directly from slice inputs, bypassing the function generators. In addition to Clock and Clock Enable signals, each slice has synchronous set and reset signals (SR and BY). SR forces a storage element into the initialization state specified for it in the configuration. BY forces it into the opposite state. Alternatively, these signals may be configured to operate asynchronously. All control signals are independently invertible, and are shared by the two flip-flops within the slice. www.xilinx.com 13 R Spartan-IIE FPGA Family: Functional Description COUT YB Y G4 I4 G2 Look-Up I3 Table O I2 G1 I1 G3 S D Carry and Control Logic YQ Q CK EC R F5IN BY SR XB X F4 I4 F2 Look-Up I3 Table O I2 F1 I1 F3 S D Carry and Control Logic XQ Q CK EC R BX CIN CLK CE DS001_04_091400 Figure 6: Spartan-IIE CLB Slice (two identical slices in each CLB) Additional Logic The F5 multiplexer in each slice combines the function generator outputs (Figure 7). This combination provides either a function generator that can implement any 5-input function, a 4:1 multiplexer, or selected functions of up to nine inputs. 14 Similarly, the F6 multiplexer combines the outputs of all four function generators in the CLB by selecting one of the two F5-multiplexer outputs. This permits the implementation of any 6-input function, an 8:1 multiplexer, or selected functions of up to 19 inputs. www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description Block RAM CLB Spartan-IIE FPGAs incorporate several large block RAM memories. These complement the distributed RAM Look-Up Tables (LUTs) that provide shallow memory structures implemented in CLBs. Slice MUXF6 LUT Block RAM memory blocks are organized in columns. Most Spartan-IIE devices contain two such columns, one along each vertical edge. The XC2S400E has four block RAM columns and the XC2S600E has six block RAM columns. These columns extend the full height of the chip. Each memory block is four CLBs high, and consequently, a Spartan-IIE device 16 CLBs high will contain four memory blocks per column, and a total of eight blocks. LUT MUXF5 Slice LUT Table 6: Spartan-IIE Block RAM Amounts LUT MUXF5 Spartan-IIE Device # of Blocks Total Block RAM Bits XC2S50E 8 32K XC2S100E 10 40K XC2S150E 12 48K XC2S200E 14 56K XC2S300E 16 64K XC2S400E 40 160K XC2S600E 72 288K DS077-2_05-111501 Figure 7: F5 and F6 Multiplexers Each CLB has four direct feedthrough paths, one per LC. These paths provide extra data input lines or additional local routing that does not consume logic resources. Arithmetic Logic Dedicated carry logic provides capability for high-speed arithmetic functions. The Spartan-IIE FPGA CLB supports two separate carry chains, one per slice. The height of the carry chains is two bits per CLB. Each block RAM cell, as illustrated in Figure 8, is a fully synchronous dual-ported 4096-bit RAM with independent control signals for each port. The data widths of the two ports can be configured independently, providing built-in bus-width conversion. The arithmetic logic includes an XOR gate that allows a 1-bit full adder to be implemented within an LC. In addition, a dedicated AND gate improves the efficiency of multiplier implementations. The dedicated carry path can also be used to cascade function generators for implementing wide logic functions. BUFTs Each Spartan-IIE FPGA CLB contains two 3-state drivers (BUFTs) that can drive on-chip busses. The IOBs on the left and right sides can also drive the on-chip busses. See Dedicated Routing, page 17. Each Spartan-IIE FPGA BUFT has an independent 3-state control pin and an independent input pin. The 3-state control pin is an active-Low enable (T). When all BUFTs on a net are disabled, the net is High. There is no need to instantiate a pull-up unless desired for simulation purposes. Simultaneously driving BUFTs onto the same net will not cause contention. If driven both High and Low, the net will be Low. DS077-2 (v2.3) June 18, 2008 Product Specification www.xilinx.com RAMB4_S#_S# WEA ENA RSTA CLKA ADD[#:0] DIA[#:0] WEB ENB RSTB CLKB ADDRB[#:0] DIB[#:0] DOA[#:0] DOB[#:0] DS001_05_060100 Figure 8: Dual-Port Block RAM 15 R Spartan-IIE FPGA Family: Functional Description Table 7 shows the depth and width aspect ratios for the block RAM. To Adjacent GRM Table 7: Block RAM Port Aspect Ratios Width Depth ADDR Bus Data Bus 1 4096 ADDR<11:0> DATA<0> 2 2048 ADDR<10:0> DATA<1:0> 4 1024 ADDR<9:0> DATA<3:0> 8 512 ADDR<8:0> DATA<7:0> 16 256 ADDR<7:0> DATA<15:0> The Spartan-IIE FPGA block RAM also includes dedicated routing to provide an efficient interface with both CLBs and other block RAMs. See Xilinx Application Note XAPP173 for more information on block RAM. Programmable Routing It is the longest delay path that limits the speed of any design. Consequently, the Spartan-IIE FPGA routing architecture and its place-and-route software were defined jointly to minimize long-path delays and yield the best system performance. The joint optimization also reduces design compilation times because the architecture is software-friendly. Design cycles are correspondingly reduced due to shorter design iteration times. The software automatically uses the best available routing based on user timing requirements. The details are provided here for reference. To Adjacent GRM * * CLB Direct Connection To Adjacent CLB DS001_06_032300 Figure 9: Spartan-IIE Local Routing General Purpose Routing Most Spartan-IIE FPGA signals are routed on the general purpose routing, and consequently, the majority of interconnect resources are associated with this level of the routing hierarchy. The general routing resources are located in horizontal and vertical routing channels associated with the rows and columns of CLBs. The general-purpose routing resources are listed below. * * * The local routing resources, as shown in Figure 9, provide the following three types of connections: Interconnections among the LUTs, flip-flops, and General Routing Matrix (GRM), described below. Internal CLB feedback paths that provide high-speed connections to LUTs within the same CLB, chaining them together with minimal routing delay Direct paths that provide high-speed connections between horizontally adjacent CLBs, eliminating the delay of the GRM To Adjacent GRM To Adjacent GRM Direct Connection To Adjacent CLB Local Routing * GRM * Adjacent to each CLB is a General Routing Matrix (GRM). The GRM is the switch matrix through which horizontal and vertical routing resources connect, and is also the means by which the CLB gains access to the general purpose routing. 24 single-length lines route GRM signals to adjacent GRMs in each of the four directions. 96 buffered Hex lines route GRM signals to other GRMs six blocks away in each one of the four directions. Organized in a staggered pattern, Hex lines may be driven only at their endpoints. Hex-line signals can be accessed either at the endpoints or at the midpoint (three blocks from the source). One third of the Hex lines are bidirectional, while the remaining ones are unidirectional. 12 Longlines are buffered, bidirectional wires that distribute signals across the device quickly and efficiently. Vertical Longlines span the full height of the device, and horizontal ones span the full width of the device. I/O Routing Spartan-IIE devices have additional routing resources around their periphery that form an interface between the CLB array and the IOBs. This additional routing, called the VersaRingTM routing, facilitates pin-swapping and pin-locking, such that logic redesigns can adapt to existing PCB layouts. Time-to-market is reduced, since PCBs and other system components can be manufactured while the logic design is still in progress. 16 www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description Dedicated Routing * Some classes of signal require dedicated routing resources to maximize performance. In the Spartan-IIE FPGA architecture, dedicated routing resources are provided for two classes of signal. * Horizontal routing resources are provided for on-chip 3-state busses. Four partitionable bus lines are provided per CLB row, permitting multiple busses within a row, as shown in Figure 10. Two dedicated nets per CLB propagate carry signals vertically to the adjacent CLB. 3-State Lines CLB CLB CLB CLB DS001_07_090600 Figure 10: BUFT Connections to Dedicated Horizontal Bus Lines Global Routing Global Routing resources distribute clocks and other signals with very high fanout throughout the device. Spartan-IIE devices include two tiers of global routing resources referred to as primary and secondary global routing resources. * * selected either from these pads or from signals in the general purpose routing. Global Clock Rows The primary global routing resources are four dedicated global nets with dedicated input pins that are designed to distribute high-fanout clock signals with minimal skew. Each global clock net can drive all CLB, IOB, and block RAM clock pins. The primary global nets may only be driven by global buffers. There are four global buffers, one for each global net. The secondary global routing resources consist of 24 backbone lines, 12 across the top of the chip and 12 across the bottom. From these lines, up to 12 unique signals per column can be distributed via the 12 longlines in the column. These secondary resources are more flexible than the primary resources since they are not restricted to routing only to clock pins. GCLKPAD2 GCLKBUF2 Global Clock Column Global Clock Spine GCLKBUF1 GCLKPAD1 GCLKBUF0 GCLKPAD0 DS001_08_060100 Figure 11: Global Clock Distribution Network Clock Distribution The Spartan-IIE family provides high-speed, low-skew clock distribution through the primary global routing resources described above. A typical clock distribution net is shown in Figure 11. Four global buffers are provided, two at the top center of the device and two at the bottom center. These drive the four primary global nets that in turn drive any clock pin. Four dedicated clock pads are provided, one adjacent to each of the global buffers. The input to the global buffer is DS077-2 (v2.3) June 18, 2008 Product Specification GCLKPAD3 GCLKBUF3 Delay-Locked Loop (DLL) Associated with each global clock input buffer is a fully digital Delay-Locked Loop (DLL) that can eliminate skew between the clock input pad and internal clock-input pins throughout the device. Each DLL can drive two global clock networks. The DLL monitors the input clock and the distributed clock, and automatically adjusts a clock delay element (Figure 12). Additional delay is introduced such that clock edges reach internal flip-flops exactly one clock period after they arrive at the input. This closed-loop system effectively eliminates clock-distribution delay by ensuring that clock www.xilinx.com 17 R Spartan-IIE FPGA Family: Functional Description edges arrive at internal flip-flops in synchronism with clock edges arriving at the input. CLKIN Variable Delay Line CLKOUT Clock Distribution Network Boundary Scan Spartan-IIE devices support all the mandatory boundary-scan instructions specified in the IEEE standard 1149.1. A Test Access Port (TAP) and registers are provided that implement the EXTEST, INTEST, SAMPLE/PRELOAD, BYPASS, IDCODE, and HIGHZ instructions. The TAP also supports two USERCODE instructions, internal scan chains, and configuration/readback of the device. Control CLKFB ds077-2_10_070203 Figure 12: Delay-Locked Loop Block Diagram In addition to eliminating clock-distribution delay, the DLL provides advanced control of multiple clock domains. The DLL provides four quadrature phases of the source clock, can double the clock, or divide the clock by 1.5, 2, 2.5, 3, 4, 5, 8, or 16. The phase-shifted output have optional duty-cycle correction (Figure 13). 0 90 180 270 0 DLL can delay the completion of the configuration process until after it has achieved lock. If the DLL uses external feedback, apply a reset after startup to ensure consistent locking to the external signal. See Xilinx Application Note XAPP174 for more information on DLLs. 90 180 270 t CLKIN The TAP uses dedicated package pins that always operate using LVTTL. For TDO to operate using LVTTL, the VCCO for Bank 2 must be 3.3V. Otherwise, TDO switches rail-to-rail between ground and VCCO. The boundary-scan input pins (TDI, TMS, TCK) do not have a VCCO requirement and operate with either 2.5V or 3.3V input signaling levels. TDI, TMS, and TCK hava a default internal weak pull-up resistor, and TDO has no default resistor. Bitstream options allow setting any of the four TAP pins to have an internal pull-up, pull-down, or neither. Boundary-scan operation is independent of individual IOB configurations, and unaffected by package type. All IOBs, including unbonded ones, are treated as independent 3-state bidirectional pins in a single scan chain. Retention of the bidirectional test capability after configuration facilitates the testing of external interconnections. CLK2X CLKDV_DIVIDE=2 CLKDV Table 8 lists the boundary-scan instructions supported in Spartan-IIE FPGAs. Internal signals can be captured during EXTEST by connecting them to unbonded or unused IOBs. They may also be connected to the unused outputs of IOBs defined as unidirectional input pins. DUTY_CYCLE_CORRECTION=FALSE CLK0 CLK90 CLK180 Table 8: Boundary-Scan Instructions CLK270 Boundary-Scan Command Binary Code[4:0] EXTEST 00000 Enables boundary-scan EXTEST operation SAMPLE/ PRELOAD 00001 Enables boundary-scan SAMPLE/PRELOAD operation USER1 00010 Access user-defined register 1 Figure 13: DLL Output Characteristics USER2 00011 Access user-defined register 2 The DLL also operates as a clock mirror. By driving the output from a DLL off-chip and then back on again, the DLL can be used to deskew a board level clock among multiple Spartan-IIE devices. CFG_OUT 00100 Access the configuration bus for Readback CFG_IN 00101 Access the configuration bus for Configuration DUTY_CYCLE_CORRECTION=TRUE CLK0 CLK90 CLK180 CLK270 x132_07_092599 In order to guarantee that the system clock is operating correctly prior to the FPGA starting up after configuration, the 18 www.xilinx.com Description DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description Table 8: Boundary-Scan Instructions (Continued) Boundary-Scan Command Binary Code[4:0] INTEST 00111 Enables boundary-scan INTEST operation USERCODE 01000 Enables shifting out USER code IDCODE 01001 Enables shifting out of ID Code HIGHZ 01010 Disables output pins while enabling the Bypass Register The public boundary-scan instructions are available prior to configuration, except for USER1 and USER2. After configuration, the public instructions remain available together with any USERCODE instructions installed during the configuration. While the SAMPLE/PRELOAD and BYPASS instructions are available during configuration, it is recommended that boundary-scan operations not be performed during this transitional period. Description JSTART 01100 Clock the start-up sequence when StartupClk is TCK BYPASS 11111 Enables BYPASS RESERVED All other codes Xilinx reserved instructions In addition to the test instructions outlined above, the boundary-scan circuitry can be used to configure the FPGA, and also to read back the configuration data. To facilitate internal scan chains, the User Register provides three outputs (Reset, Update, and Shift) that represent the corresponding states in the boundary-scan internal state machine. Figure 14 is a diagram of the Spartan-IIE family boundary scan logic. It includes three bits of Data Register per IOB, the IEEE 1149.1 Test Access Port controller, and the Instruction Register with decodes. DATA IN IOB.T 0 1 0 IOB IOB IOB IOB sd D D Q 1 LE IOB IOB Q IOB 1 sd D Q D Q 0 IOB IOB IOB IOB LE 1 IOB.I IOB IOB IOB IOB IOB IOB 0 1 IOB TDI 0 Instruction Register Q D Q LE 1 0 IOB.Q IOB Bypass Register sd D M TDO U X IOB.T 0 1 0 sd D Q D Q 1 LE 1 0 sd D Q D Q LE 1 IOB.I 0 DATAOUT SHIFT/ CAPTURE UPDATE CLOCK DATA REGISTER EXTEST DS001_09_032300 Figure 14: Spartan-IIE Family Boundary Scan Logic DS077-2 (v2.3) June 18, 2008 Product Specification www.xilinx.com 19 R Spartan-IIE FPGA Family: Functional Description Bit Sequence Bit 0 ( TDO end) Bit 1 Bit 2 The bit sequence within each IOB is: In, Out, 3-State. The input-only pins contribute only the In bit to the boundary scan I/O data register, while the output-only pins contributes all three bits. TDO.T TDO.O Top-edge IOBs (Right to Left) Left-edge IOBs (Top to Bottom) From a cavity-up view of the chip (as shown in the FPGA Editor), starting in the upper right chip corner, the boundary scan data-register bits are ordered as shown in Figure 15. MODE.I BSDL (Boundary Scan Description Language) files for Spartan-IIE family devices are available on the Xilinx web site at: http://www.xilinx.com/support/download/sp2ebsdl.htm. Bottom-edge IOBs (Left to Right) Spartan-IIE FPGA boundary scan IDCODE values are shown in Table 9. Right-edge IOBs (Bottom to Top) (TDI end) BSCANT.UPD DS001_10_032300 Figure 15: Boundary Scan Bit Sequence Table 9: Spartan-IIE IDCODE Values IDCODE Device Version Family Array Size Manufacturer Required XC2S50E XXXX 0000 101 0 0001 0000 0000 1001 001 1 XC2S100E XXXX 0000 101 0 0001 0100 0000 1001 001 1 XC2S150E XXXX 0000 101 0 0001 1000 0000 1001 001 1 XC2S200E XXXX 0000 101 0 0001 1100 0000 1001 001 1 XC2S300E XXXX 0000 101 0 0010 0000 0000 1001 001 1 XC2S400E XXXX 0000 101 0 0010 1000 0000 1001 001 1 XC2S600E XXXX 0000 101 0 0011 0000 0000 1001 001 1 Development System Spartan-IIE FPGAs are supported by the Xilinx ISE(R) CAE tools. The basic methodology for Spartan-IIE FPGA design consists of three interrelated steps: design entry, implementation, and verification. Industry-standard tools are used for design entry and simulation, while Xilinx provides proprietary architecture-specific tools for implementation. The Xilinx development system is integrated under the Xilinx Project Navigator software, providing designers with a common user interface regardless of their choice of entry and verification tools. The software simplifies the selection of implementation options with pull-down menus and on-line help. Several advanced software features facilitate Spartan-IIE FPGA design. CORE GeneratorTM tool functions, for example, include macros with relative location constraints to guide their placement. They help ensure optimal implementation of common functions. 20 For HDL design entry, the Xilinx FPGA development system provides interfaces to several synthesis design environments. A standard interface-file specification, Electronic Design Interchange Format (EDIF), simplifies file transfers into and out of the development system. Spartan-IIE FPGAs are supported by a unified library of standard functions. This library contains over 400 primitives and macros, ranging from 2-input AND gates to 16-bit accumulators, and includes arithmetic functions, comparators, counters, data registers, decoders, encoders, I/O functions, latches, Boolean functions, multiplexers, shift registers, and barrel shifters. The design environment supports hierarchical design entry, with high-level designs that comprise major functional blocks, while lower-level designs define the logic in these blocks. These hierarchical design elements are automatically combined by the implementation tools. Different design entry tools can be combined within a hierarchical www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description design, thus allowing the most convenient entry method to be used for each portion of the design. Design Implementation The place-and-route tools automatically provide the implementation flow described in this section. The partitioner takes the EDIF netlist for the design and maps the logic into the architectural resources of the FPGA (CLBs and IOBs, for example). The placer then determines the best locations for these blocks based on their interconnections and the desired performance. Finally, the router interconnects the blocks. The algorithms support fully automatic implementation of most designs. For demanding applications, however, the user can exercise various degrees of control over the process. User partitioning, placement, and routing information is optionally specified during the design-entry process. The implementation of highly structured designs can benefit greatly from basic floorplanning. The implementation software incorporates timing-driven placement and routing. Designers specify timing requirements along entire paths during design entry. The timing path analysis routines then recognize these user-specified requirements and accommodate them. Configuration Configuration is the process by which the bitstream of a design, as generated by the Xilinx development software, is loaded into the internal configuration memory of the FPGA. Spartan-IIE devices support both serial configuration, using the master/slave serial and JTAG modes, as well as byte-wide configuration employing the Slave Parallel mode. Configuration File Spartan-IIE devices are configured by sequentially loading frames of data that have been concatenated into a configuration file. Table 10 shows how much nonvolatile storage space is needed for Spartan-IIE devices. It is important to note that, while a PROM is commonly used to store configuration data before loading them into the FPGA, it is by no means required. Any of a number of different kinds of under populated nonvolatile storage already available either on or off the board (for example, hard drives, FLASH cards, and so on) can be used. Table 10: Spartan-IIE Configuration File Size Timing requirements are entered in a form directly relating to the system requirements, such as the targeted clock frequency, or the maximum allowable delay between two registers. In this way, the overall performance of the system along entire signal paths is automatically tailored to user-generated specifications. Specific timing information for individual nets is unnecessary. Device Configuration File Size (Bits) XC2S50E 630,048 XC2S100E 863,840 XC2S150E 1,134,496 XC2S200E 1,442,016 XC2S300E 1,875,648 XC2S400E 2,693,440 XC2S600E 3,961,632 Design Verification Modes In addition to conventional software simulation, FPGA users can use in-circuit debugging techniques. Because Xilinx devices are infinitely reprogrammable, designs can be verified in real time without the need for extensive sets of software simulation vectors. Spartan-IIE devices support the following four configuration modes: The development system supports both software simulation and in-circuit debugging techniques. For simulation, the system extracts the post-layout timing information from the design database, and back-annotates this information into the netlist for use by the simulator. Alternatively, the user can verify timing-critical portions of the design using the static timing analyzer. For in-circuit debugging, Xilinx offers a download cable, which connects the FPGA in the target system to a PC or workstation. After downloading the design into the FPGA, the designer can read back the contents of the flip-flops, and so observe the internal logic state. Simple modifications can be downloaded into the system in a matter of minutes. DS077-2 (v2.3) June 18, 2008 Product Specification * * * * Slave Serial mode Master Serial mode Slave Parallel mode Boundary-scan mode The Configuration mode pins (M2, M1, M0) select among these configuration modes with the option in each case of having the IOB pins either pulled up or left floating prior to the end of configuration. The selection codes are listed in Table 11. Configuration through the boundary-scan port is always available, independent of the mode selection. Selecting the boundary-scan mode simply turns off the other modes. The three mode pins have internal pull-up resistors, and default to a logic High if left unconnected. www.xilinx.com 21 R Spartan-IIE FPGA Family: Functional Description Table 11: Configuration Modes Preconfiguration Pull-ups M0 M1 M2 CCLK Direction Data Width Serial DOUT No 0 0 0 Out 1 Yes Yes 0 0 1 Slave Parallel mode (SelectMAP) Yes 0 1 0 In 8 No No 0 1 1 Boundary-Scan mode Yes 1 0 0 N/A 1 No No 1 0 1 Yes 1 1 0 In 1 Yes No 1 1 1 Configuration Mode Master Serial mode Slave Serial mode Notes: 1. During power-on and throughout configuration, the I/O drivers will be in a high-impedance state. After configuration, all unused I/Os (those not assigned signals) will remain in a high-impedance state. Pins used as outputs may pulse High at the end of configuration (see Answer 10504). 2. If the Mode pins are set for preconfiguration pull-ups, those resistors go into effect once the rising edge of INIT samples the Mode pins. They will stay in effect until GTS is released during startup, after which the UnusedPin bitstream generator option will determine whether the unused I/Os have a pull-up, pull-down, or no resistor. Signals There are two kinds of pins that are used to configure Spartan-IIE devices: Dedicated pins perform only specific configuration-related functions; the other pins can serve as general purpose I/Os once user operation has begun. The dedicated pins comprise the mode pins (M2, M1, M0), the configuration clock pin (CCLK), the PROGRAM pin, the DONE pin and the boundary-scan pins (TDI, TDO, TMS, TCK). Depending on the selected configuration mode, CCLK may be an output generated by the FPGA, or may be generated externally, and provided to the FPGA as an input. Note that some configuration pins can act as outputs. For correct operation, these pins require a VCCO of 3.3V to drive an LVTTL signal or 2.5V to drive an LVCMOS signal. All the relevant pins fall in banks 2 or 3. The CS and WRITE pins for Slave Parallel mode are located in bank 1. For a more detailed description than that given below, see Module 1 and XAPP176, Configuration and Readback of the Spartan-II and Spartan-IIE FPGA Families. The Process The sequence of steps necessary to configure Spartan-IIE devices are shown in Figure 16. The overall flow can be divided into three different phases. * * 22 * * Loading data frames Start-up The memory clearing and start-up phases are the same for all configuration modes; however, the steps for the loading of data frames are different. Thus, the details for data frame loading are described separately in the sections devoted to each mode. Initiating Configuration There are two different ways to initiate the configuration process: applying power to the device or asserting the PROGRAM input. Configuration on power-up occurs automatically unless it is delayed by the user, as described in a separate section below. The waveform for configuration on power-up is shown in Configuration Switching Characteristics, page 48. Before configuration can begin, VCCO Bank 2 must be greater than 1.0V. Furthermore, all VCCINT power pins must be connected to a 1.8V supply. For more information on delaying configuration, see Clearing Configuration Memory, page 23. Once in user operation, the device can be re-configured simply by pulling the PROGRAM pin Low. The device acknowledges the beginning of the configuration process by driving DONE Low, then enters the memory-clearing phase. Initiating configuration Configuration memory clear www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description Clearing Configuration Memory Configuration at Power-up Configuration During User Operation The device indicates that clearing the configuration memory is in progress by driving INIT Low. Delaying Configuration VCCO AND No User Pulls PROGRAM Low VCCINT High? Yes At this time, the user can delay configuration by holding either PROGRAM or INIT Low, which causes the device to remain in the memory clearing phase. Note that the bidirectional INIT line is driving a Low logic level during memory clearing. Thus, to avoid contention, use an open-drain driver to keep INIT Low. With no delay in force, the device indicates that the memory is completely clear by driving INIT High. The FPGA samples its mode pins on this Low-to-High transition. FPGA Drives INIT and DONE Low Loading Configuration Data Clear Configuration Memory User Holding PROGRAM Low? Delay Configuration Yes CRC Error Checking No Delay Configuration User Holding INIT Low? Yes No FPGA Samples Mode Pins After the loading of configuration data, a CRC value embedded in the configuration file is checked against a CRC value calculated within the FPGA. If the CRC values do not match, the FPGA drives INIT Low to indicate that an error has occurred and configuration is aborted. Note that attempting to load an incorrect bitstream causes configuration to fail and can damage the device. To reconfigure the device, the PROGRAM pin should be asserted to reset the configuration logic. Recycling power also resets the FPGA for configuration. See Clearing Configuration Memory. Load Configuration Data Frames CRC Correct? Once INIT is High, the user can begin loading configuration data frames into the device. The details of loading the configuration data are discussed in the sections treating the configuration modes individually. The sequence of operations necessary to load configuration data using the serial modes is shown in Figure 18. Loading data using the Slave Parallel mode is shown in Figure 21, page 28. Start-up No FPGA Drives INIT Low Abort Start-up The start-up sequence oversees the transition of the FPGA from the configuration state to full user operation. A match of CRC values, indicating a successful loading of the configuration data, initiates the sequence. Yes Start-up Sequence FPGA Drives DONE High, Activates I/Os, Releases GSR net User Operation DS001_11_111501 Figure 16: Configuration Flow Diagram DS077-2 (v2.3) June 18, 2008 Product Specification www.xilinx.com 23 R Spartan-IIE FPGA Family: Functional Description During start-up, the device performs four operations: Default Cycles 1. The assertion of DONE. The failure of DONE to go High may indicate the unsuccessful loading of configuration data. Start-up CLK 2. The release of the Global Three State (GTS). This activates all the I/Os to which signals are assigned. The remaining I/Os stay in a high-impedance state with internal weak pull-up resistors present. Phase GTS 4. The assertion of Global Write Enable (GWE). This allows all RAMs and flip-flops to change state. GSR By default, these operations are synchronized to CCLK. The entire start-up sequence lasts eight cycles, called C0-C7, after which the loaded design is fully functional. The four operations can be selected to switch on any CCLK cycle C1-C6 through settings in the Xilinx Development Software. The default timing for start-up is shown in the top half of Figure 17; heavy lines show default settings. 2 3 4 5 6 7 GWE Sync to DONE Start-up CLK Phase The default Start-up sequence is that one CCLK cycle after DONE goes High, the global 3-state signal (GTS) is released. This permits device outputs to turn on as necessary. 0 1 2 3 4 5 6 7 DONE High One CCLK cycle later, the Global Set/Reset (GSR) and Global Write Enable (GWE) signals are released. This permits the internal storage elements to begin changing state in response to the logic and the user clock. DONE The bottom half of Figure 17 shows another commonly used version of the start-up timing known as Sync-to-DONE. This version makes the GTS, GSR, and GWE events conditional upon the DONE pin going High. This timing is important for a daisy chain of multiple FPGAs in serial mode, since it ensures that all FPGAs go through start-up together, after all their DONE pins have gone High. GSR The sequence can also be paused at any stage until lock has been achieved on any or all DLLs. 1 DONE 3. The release of the Global Set Reset (GSR). This allows all flip-flops to change state. Sync-to-DONE timing is selected by setting the GTS, GSR, and GWE cycles to a value of DONE in the configuration options. This causes these signals to transition one clock cycle after DONE externally transitions High. 0 GTS GWE DS001_13_090600 Figure 17: Start-Up Waveforms Serial Modes There are two serial configuration modes. In Master Serial mode, the FPGA controls the configuration process by driving CCLK as an output. In Slave Serial mode, the FPGA passively receives CCLK as an input from an external agent (e.g., a microprocessor, CPLD, or second FPGA in master mode) that is controlling the configuration process. In both modes, the FPGA is configured by loading one bit per CCLK cycle. The MSB of each configuration data byte is always written to the DIN pin first. See Figure 18 for the sequence for loading data into the Spartan-IIE FPGA serially. This is an expansion of the "Load Configuration Data Frames" block in Figure 16, page 23. Note that CS and WRITE are not normally used during serial configuration. To ensure successful loading of the FPGA, do not toggle WRITE with CS Low during serial configuration. 24 www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description from a PROM. A Spartan-IIE device in slave serial mode should be connected as shown for the third device from the left. Slave Serial mode is selected by a <11x> on the mode pins (M0, M1, M2). The weak pull-ups on the mode pins make slave serial the default mode if the pins are left unconnected. After INIT Goes High User Load One Configuration Bit on Next CCLK Rising Edge End of Configuration Data File? The serial bitstream must be setup at the DIN input pin a short time before each rising edge of an externally generated CCLK. Timing for Slave Serial mode is shown in Figure 24, page 49. No Daisy Chain Yes To CRC Check DS001_14_032300 Figure 18: Loading Serial Mode Configuration Data Slave Serial Mode In Slave Serial mode, the FPGA's CCLK pin is driven by an external source, allowing the FPGA to be configured from other logic devices such as microprocessors or in a daisy-chain configuration. Figure 19 shows connections for a Master Serial FPGA configuring a Slave Serial FPGA 3.3V M0 M1 M2 VCCO VCCINT 1.8V Multiple FPGAs in Slave Serial mode can be daisy-chained for configuration from a single source. After an FPGA is configured, data for the next device is sent to the DOUT pin. Data on the DOUT pin changes on the rising edge of CCLK. Note that DOUT changes on the falling edge of CCLK for some Xilinx families but mixed daisy chains are allowed. Configuration must be delayed until INIT pins of all daisy-chained FPGAs are High. For more information, see Start-up, page 23. The maximum amount of data that can be sent to the DOUT pin for a serial daisy chain is 220-1 (1,048,575) 32-bit words, or 33,554,400 bits, which is approximately 8 XC2S600E bitstreams. The configuration bitstream of downstream devices is limited to this size. 3.3 K VCCINT DIN DOUT CCLK Spartan-IIE (Master Serial) VCC CLK Xilinx PROM DIN DATA PROGRAM CE DONE INIT RESET/OE GND 1.8V VCCO M0 M1 M2 DOUT CCLK 3.3V 3.3V 3.3V CEO Spartan-IIE (Slave) PROGRAM DONE GND INIT GND PROGRAM DS077-2_04_061708 Notes: 1. If the DriveDone configuration option is not active for any of the FPGAs, pull up DONE with a 330 resistor. Figure 19: Master/Slave Serial Configuration Circuit Diagram DS077-2 (v2.3) June 18, 2008 Product Specification www.xilinx.com 25 R Spartan-IIE FPGA Family: Functional Description Master Serial Mode In Master Serial mode, the CCLK output of the FPGA drives a Xilinx PROM, which feeds a serial stream of configuration data to the FPGA's DIN input. Figure 19 shows a Master Serial FPGA configuring a Slave Serial FPGA from a PROM. A Spartan-IIE device in Master Serial mode should be connected as shown for the device on the left side. Master Serial mode is selected by a <00x> on the mode pins (M0, M1, M2). The PROM RESET pin is driven by INIT, and the CE input is driven by DONE. For more information on serial PROMs, see the Xilinx Configuration PROM data sheets at: www.xilinx.com/support/documentation/configuration_proms_data_sheets.htm The interface is identical to the slave serial mode except that an oscillator internal to the FPGA is used to generate the configuration clock (CCLK). Any of a number of different frequencies ranging from 4 to 60 MHz can be set using the ConfigRate option in the Xilinx development software. When selecting a CCLK frequency, ensure that the serial PROM and any daisy-chained FPGAs are fast enough to support the clock rate. On power-up, while the first 60 bytes of the configuration data are being loaded, the CCLK frequency is always 2.5 MHz. This frequency is used until the ConfigRate bits, part of the configuration file, have been loaded into the FPGA, at which point the frequency changes to the selected ConfigRate. Unless a different frequency is specified in the design, the default ConfigRate is 4 MHz. The frequency of the CCLK signal created by the internal oscillator has a variance of +45%, -30% from the specified value. 26 The FPGA accepts one bit of configuration data on each rising CCLK edge. After the FPGA has been loaded, the data for the next device in a daisy-chain is presented on the DOUT pin after the rising CCLK edge. The timing for Master Serial mode is shown in Figure 25, page 49. Slave Parallel Mode (SelectMAP) The Slave Parallel mode, also known as SelectMAP, is the fastest configuration option. Byte-wide data is written into the FPGA on the D0-D7 pins. Note that D0 is the MSB of each byte for configuration. A BUSY flag is provided for controlling the flow of data at a clock frequency above 50 MHz. Figure 20, page 27 shows the connections for two Spartan-IIE devices using the Slave Parallel mode. Slave Parallel mode is selected by a <011> on the mode pins (M0, M1, M2). The agent controlling configuration is not shown. Typically, a processor, a microcontroller, or CPLD controls the Slave Parallel interface. The controlling agent provides byte-wide configuration data, CCLK, a Chip Select (CS) signal and a Write signal (WRITE). If BUSY is asserted (High) by the FPGA, the data must be held until BUSY goes Low. After configuration, the pins of the Slave Parallel port (D0-D7) can be used as additional user I/O. Alternatively, the port may be retained to permit high-speed 8-bit readback. Then data can be read by deasserting WRITE. If retention is selected, prohibit the D0-D7 pins from being used as user I/O. See Readback, page 28. www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description DATA[7:0] CCLK WRITE BUSY M1 M2 M1 M2 M0 M0 Spartan-IIE Spartan-IIE D0:D7 D0:D7 CCLK CCLK WRITE WRITE BUSY CS(0) BUSY CS(1) CS CS PROGRAM PROGRAM DONE INIT GND DONE INIT GND DONE INIT PROGRAM DS077-2_06_110102 Figure 20: Slave Parallel Configuration Circuit Diagram Multiple Spartan-IIE FPGAs can be configured using the Slave Parallel mode, and be made to start-up simultaneously. To configure multiple devices in this way, wire the individual CCLK, Data, WRITE, and BUSY pins of all the devices in parallel. The individual devices are loaded separately by asserting the CS pin of each device in turn and writing the appropriate data. Sync-to-DONE start-up timing is used to ensure that the start-up sequence does not begin until all the FPGAs have been loaded. See Start-up, page 23. Write When using the Slave Parallel Mode, write operations send packets of byte-wide configuration data into the FPGA. Figure 21, page 28 shows a flowchart of the write sequence used to load data into the Spartan-IIE FPGA. This is an expansion of the "Load Configuration Data Frames" block in Figure 16, page 23. The timing for Slave Parallel mode is shown in Figure 26, page 50. For the present example, the user holds WRITE and CS Low throughout the sequence of write operations. Note that when CS is asserted on successive CCLKs, WRITE must remain either asserted or deasserted. Otherwise an abort will be initiated, as in the next section. 1. Drive data onto D0-D7. Note that to avoid contention, the data source should not be enabled while CS is Low and WRITE is High. Similarly, while WRITE is High, no more than one device's CS should be asserted. 2. On the rising edge of CCLK: If BUSY is Low, the data is accepted on this clock. If BUSY is High (from a previous write), the data is not accepted. Acceptance will instead occur on the first clock after BUSY goes Low, and the data must be held until this happens. 3. Repeat steps 1 and 2 until all the data has been sent. 4. Deassert CS and WRITE. DS077-2 (v2.3) June 18, 2008 Product Specification www.xilinx.com 27 R Spartan-IIE FPGA Family: Functional Description If CCLK is slower than FCCNH, the FPGA will never assert BUSY. In this case, the above handshake is unnecessary, and data can simply be entered into the FPGA every CCLK cycle. Abort To abort configuration during a write sequence, deassert WRITE while holding CS Low. The abort operation is initiated at the rising edge of CCLK. The device will remain BUSY until the aborted operation is complete. After aborting configuration, data is assumed to be unaligned to word boundaries and the FPGA requires a new synchronization word prior to accepting any new packets. After INIT Goes High User Drives WRITE and CS Low Boundary-Scan Configuration Mode In the boundary-scan mode, no nondedicated pins are required, configuration being done entirely through the IEEE 1149.1 Test Access Port (TAP). Load One Configuration Byte on Next CCLK Rising Edge FPGA Driving BUSY High? tions. However, to avoid aborting configuration, WRITE must continue to be asserted while CS is asserted during CCLK transitions. Configuration through the TAP uses the special CFG_IN instruction. This instruction allows data input on TDI to be converted into data packets for the internal configuration bus. The following steps are required to configure the FPGA through the boundary-scan port. Yes 1. Load the CFG_IN instruction into the boundary-scan instruction register (IR) 2. Enter the Shift-DR (SDR) state No 3. Shift a standard configuration bitstream into TDI End of Configuration Data File? 4. Return to Run-Test-Idle (RTI) No 5. Load the JSTART instruction into IR 6. Enter the SDR state Yes 7. Clock TCK (if selected) through the startup sequence (the length is programmable) User Drives WRITE and CS High 8. Return to RTI To CRC Check DS001_19_032300 Figure 21: Loading Configuration Data for the Slave Parallel Mode A configuration packet does not have to be written in one continuous stretch, rather it can be split into many write sequences. Each sequence would involve assertion of CS. In applications where multiple clock cycles may be required to access the configuration data before each byte can be loaded into the Slave Parallel interface, a new byte of data may not be ready for each consecutive CCLK edge. In such a case the CS signal may be deasserted until the next byte is valid on D0-D7. While CS is High, the Slave Parallel interface does not expect any data and ignores all CCLK transi28 Configuration and readback via the TAP is always available. The boundary-scan mode simply locks out the other modes. The boundary-scan mode is selected by a <10x> on the mode pins (M0, M1, M2). Note that the PROGRAM pin must be pulled High prior to reconfiguration. A Low on the PROGRAM pin resets the TAP controller and no boundary scan operations can be performed. See Xilinx Application Note XAPP188 for more information on boundary-scan configuration. Readback The configuration data stored in the Spartan-IIE FPGA configuration memory can be read back for verification. Along with the configuration data it is possible to read back the contents of all flip-flops/latches, LUT RAMs, and block RAMs. This capability is used for real-time debugging. For more detailed information see Xilinx Application Note XAPP176, Configuration and Readback of the Spartan-II and Spartan-IIE FPGA Families. www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Functional Description Revision History Version No. Date 1.0 11/15/01 Initial Xilinx release. 2.0 11/18/02 Added XC2S400E and XC2S600E. Removed Preliminary designation. Clarified details of I/O standards, boundary scan, and configuration. 2.1 07/09/03 Added hot swap description (see Hot Swap, Hot Insertion, Hot Socketing Support). Added Table 9 containing JTAG IDCODE values. Clarified configuration PROM support. 2.3 06/18/08 Added note that TDI, TMS, and TCK have a default pull-up resistor. Add note on maximum daisy-chain limit. Updated Figure 19 since Mode pins can be pulled up to either 2.5V or 3.3V. Updated all modules for continuous page, figure, and table numbering. Updated links. Synchronized all modules to v2.3. DS077-2 (v2.3) June 18, 2008 Product Specification Description www.xilinx.com 29 R Spartan-IIE FPGA Family: Functional Description 30 www.xilinx.com DS077-2 (v2.3) June 18, 2008 Product Specification Spartan-IIE FPGA Family: DC and Switching Characteristics R DS077-3 (v2.3) June 18, 2008 0 Product Specification Definition of Terms In this document, some specifications may be designated as Advance or Preliminary. These designations are based on the more detailed timing information used by the development system and reported in the output files. These terms are defined as follows: Advance: Initial estimates based on simulation and/or extrapolation from other speed grades, devices, or families. Values are subject to change. Use as estimates, not for production. Preliminary: Based on characterization. Further changes are not expected. Except for pin-to-pin input and output parameters, the AC parameter delay specifications included in this document are derived from measuring internal test patterns. All specifications are representative of worst-case supply voltage and junction temperature conditions. The parameters included are common to popular designs and typical applications. All specifications are subject to change without notice. DC Specifications Absolute Maximum Ratings (1) Symbol Description Min Max Units VCCINT Supply voltage relative to GND -0.5 2.0 V VCCO Supply voltage relative to GND -0.5 4.0 V VREF Input reference voltage -0.5 4.0 V -0.5 4.0 V GND (2,3) VIN Input voltage relative to VTS Voltage applied to 3-state output(3) -0.5 4.0 V TSTG Storage temperature (ambient) -65 +150 C - +125 C TJ Junction temperature Notes: 1. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time may affect device reliability. 2. VIN should not exceed VCCO by more than 3.6V over extended periods of time (e.g., longer than a day). 3. Maximum DC overshoot must be limited to either VCCO + 0.5V or 10 mA, and undershoot must be limited to -0.5V or 10 mA, whichever is easier to achieve. The Maximum AC conditions are as follows: The device pins may undershoot to -2.0V or overshoot to VCCO + 2.0V, provided this over/undershoot lasts no more than 11 ns with a forcing current no greater than 100 mA. 4. For soldering guidelines, see the Packaging Information on the Xilinx(R) website. (c) 2003-2007 Xilinx, Inc. All rights reserved. XILINX, the Xilinx logo, the Brand Window, and other designated brands included herein are trademarks of Xilinx, Inc. All other trademarks are the property of their respective owners. DS077-3 (v2.3) June 18, 2008 Product Specification www.xilinx.com 31 R Spartan-IIE FPGA Family: DC and Switching Characteristics Recommended Operating Conditions Symbol TJ Description Junction temperature Min 0 85 C 100 C Commercial 1.8 - 5% 1.8 + 5% V Industrial 1.8 - 5% 1.8 + 5% V Commercial 1.2 3.6 V Industrial 1.2 3.6 V - 250 ns Industrial VCCINT VCCO TIN Supply voltage relative to Supply voltage relative to GND (2) Input signal transition Units -40 Commercial GND (1) Max time (3) Notes: 1. Functional operation is guaranteed down to a minimum VCCINT of 1.62V (Nominal VCCINT -10%). For every 50 mV reduction in VCCINT below 1.71V (nominal VCCINT -5%), all delay parameters increase by approximately 3%. 2. Minimum and maximum values for VCCO vary according to the I/O standard selected. 3. Input and output measurement threshold is ~50% of VCCO. See Delay Measurement Methodology, page 41 for specific details. DC Characteristics Over Operating Conditions Symbol Description Min Typ Max Units VDRINT Data retention VCCINT voltage (below which configuration data may be lost) 1.5 - - V VDRIO Data retention VCCO voltage (below which configuration data may be lost) 1.2 - - V Commercial - 10 200 mA Industrial - 10 200 mA Commercial - 10 200 mA Industrial - 10 200 mA Commercial - 10 300 mA Industrial - 10 300 mA Commercial - 10 300 mA Industrial - 10 300 mA Commercial - 12 300 mA Industrial - 12 300 mA Commercial - 15 300 mA Industrial - 15 300 mA Commercial - 15 400 mA Industrial ICCINTQ Quiescent VCCINT supply current (1) XC2S50E XC2S100E XC2S150E XC2S200E XC2S300E XC2S400E XC2S600E ICCOQ IREF IL - 15 400 mA Quiescent VCCO supply current (1) - - 2 mA VREF current per VREF pin - - 20 A -10 - +10 A Input or output leakage current per pin CIN Input capacitance (sample tested) - - 8 pF IRPU Pad pull-up (when selected) @ VIN = 0V, VCCO = 3.3V (sample tested) (2) TQ, PQ, FG, FT packages - - 0.25 mA IRPD Pad pull-down (when selected) @ VIN = 3.6V (sample tested) (2) - - 0.25 mA Notes: 1. With no output current loads, no active input pull-up resistors, all I/O pins 3-stated and floating. 2. Internal pull-up and pull-down resistors guarantee valid logic levels at unconnected input pins. These pull-up and pull-down resistors do not provide valid logic levels when input pins are connected to other circuits. 32 www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics Power-On Requirements Spartan(R)-IIE FPGAs require that a minimum supply current ICCPO be provided to the VCCINT lines for a successful power-on. If more current is available, the FPGA can consume more than ICCPO min., though this cannot adversely affect reliability. Symbol I CCPO A maximum limit for ICCPO is not specified. Be careful when using foldback/crowbar supplies and fuses. It is possible to control the magnitude of ICCPO by limiting the supply current available to the FPGA. A current limit below the trip level will avoid inadvertently activating over-current protection circuits. Min(1) Typ Max Units After PCN(2) 300 - - mA Before PCN(2) 500 - - mA 500 - - mA 500 - - mA 2 - - A XC2S400E - XC2S600E 700 - - mA After PCN(2) 500 - - s 2 - 50 ms - 60 - A Description Total VCCINT supply current required during power-on Commercial XC2S50E - XC2S300E XC2S400E - XC2S600E Industrial XC2S50E - XC2S300E After PCN(2) Before PCN(2) TCCPO VCCINT(3,4) ramp time Before IHSPO AC current per pin during power-on in hot-swap applications when VIN > VCCO + 0.4V; duration < 10ns After PCN(2) PCN(2) Notes: 1. The ICCPO requirement applies for a brief time (commonly only a few milliseconds) when VCCINT ramps from 0 to 1.8V. 2. Devices built after the Product Change Notice PCN 2002-05 (see http://www.xilinx.com/support/documentation/customer_notices/pcn2002-05.pdf) have improved power-on requirements. Devices after the PCN have a `T' preceding the date code as referenced in the PCN. Note that the XC2S150E, XC2S400E, and XC2S600E always have this mark. Devices before the PCN have an `S' preceding the date code. Note that devices before the PCN are measured with VCCINT and VCCO powering up simultaneously. 3. The ramp time is measured from GND to 1.8V on a fully loaded board. 4. VCCINT must not dip in the negative direction during power on. 5. I/Os are not guaranteed to be disabled until VCCINT is applied. 6. For more information on designing to meet the power-on specifications, refer to the application note XAPP450 "Power-On Current Requirements for the Spartan-II and Spartan-IIE Families". DC Input and Output Levels standards meet their specifications. The selected standards are tested at minimum VCCO with the respective IOL and IOH currents shown. Other standards are sample tested. Values for VIL and VIH are recommended input voltages. Values for VOL and VOH are guaranteed output voltages over the recommended operating conditions. Only selected standards are tested. These are chosen to ensure that all Input/Output Standard VIL VIH VOL VOH IOL IOH V, Min V, Max V, Min V, Max V, Max V, Min mA mA LVTTL(1) -0.5 0.8 2.0 3.6 0.4 2.4 24 -24 LVCMOS2 -0.5 0.7 1.7 2.7 0.4 1.9 12 -12 LVCMOS18 -0.5 35% VCCO 65% VCCO 1.95 0.4 VCCO - 0.4 8 -8 PCI, 3.3V -0.5 30% VCCO 50% VCCO VCCO + 0.5 10% VCCO 90% VCCO Note (2) Note (2) GTL -0.5 VREF - 0.05 VREF + 0.05 3.6 0.4 - 40 - GTL+ -0.5 VREF - 0.1 VREF + 0.1 3.6 0.6 - 36 - DS077-3 (v2.3) June 18, 2008 Product Specification www.xilinx.com 33 R Spartan-IIE FPGA Family: DC and Switching Characteristics Input/Output Standard VIH VIL VOL VOH IOL IOH V, Min V, Max V, Min V, Max V, Max V, Min mA mA HSTL I -0.5 VREF - 0.1 VREF + 0.1 3.6 0.4 VCCO - 0.4 8 -8 HSTL III -0.5 VREF - 0.1 VREF + 0.1 3.6 0.4 VCCO - 0.4 24 -8 HSTL IV -0.5 VREF - 0.1 VREF + 0.1 3.6 0.4 VCCO - 0.4 48 -8 SSTL3 I -0.5 VREF - 0.2 VREF + 0.2 3.6 VREF - 0.6 VREF + 0.6 8 -8 SSTL3 II -0.5 VREF - 0.2 VREF + 0.2 3.6 VREF - 0.8 VREF + 0.8 16 -16 SSTL2 I -0.5 VREF - 0.2 VREF + 0.2 3.6 VREF - 0.61 VREF + 0.61 7.6 -7.6 SSTL2 II -0.5 VREF - 0.2 VREF + 0.2 3.6 VREF - 0.8 VREF + 0.8 15.2 -15.2 CTT -0.5 VREF - 0.2 VREF + 0.2 3.6 VREF - 0.4 VREF + 0.4 8 -8 AGP -0.5 VREF - 0.2 VREF + 0.2 3.6 10% VCCO 90% VCCO Note (2) Note (2) Notes: 1. VOL and VOH for lower drive currents are sample tested. 2. Tested according to the relevant specifications. LVDS DC Specifications Symbol VCCO Description Conditions Supply voltage Min Typ Max Units 2.375 2.5 2.625 V VOH Output High voltage for Q and Q RT = 100 across Q and Q signals 1.25 1.425 1.6 V VOL Output Low voltage for Q and Q RT = 100 across Q and Q signals 0.9 1.075 1.25 V VODIFF Differential output voltage (Q - Q), Q = High or (Q - Q), Q = High RT = 100 across Q and Q signals 250 350 450 mV VOCM Output common-mode voltage RT = 100 across Q and Q signals 1.125 1.25 1.375 V VIDIFF Differential input voltage (Q - Q), Q = High or (Q - Q), Q = High Common-mode input voltage = 1.25 V 100 350 - mV VICM Input common-mode voltage Differential input voltage = 350 mV 0.2 1.25 2.2 V LVPECL DC Specifications These values are valid at the output of the source termination pack shown under LVPECL, with a 100 differential load only. The VOH levels are 200 mV below standard DC Parameter Min VCCO 34 LVPECL levels and are compatible with devices tolerant of lower common-mode ranges. The following table summarizes the DC output specifications of LVPECL. Max Min 3.0 Max Min 3.3 Max 3.6 Units V VOH 1.8 2.11 1.92 2.28 2.13 2.41 V VOL 0.96 1.27 1.06 1.43 1.30 1.57 V VIH 1.49 2.72 1.49 2.72 1.49 2.72 V VIL 0.86 2.125 0.86 2.125 0.86 2.125 V Differential input voltage 0.3 - 0.3 - 0.3 - V www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics Switching Characteristics Internal timing parameters are derived from measuring internal test patterns. Listed below are representative values. For more specific, more precise, and worst-case guaranteed data, use the values reported by the static timing analyzer (TRACE in the Xilinx Development System) and back-annotated to the simulation netlist. All timing parameters assume worst-case operating conditions (supply voltage and junction temperature). Values apply to all Spartan-IIE devices unless otherwise noted. Global Clock Input to Output Delay for LVTTL, with DLL (Pin-to-Pin)(1) Speed Grade All -7 -6 Symbol Description Min Max Max Units TICKOFDLL LVTTL global clock input to output delay using output flip-flop for LVTTL, 12 mA, fast slew rate, with DLL. 1.0 3.1 3.1 ns Notes: 1. Listed above are representative values where one global clock input drives one vertical clock line in each accessible column, and where all accessible IOB and CLB flip-flops are clocked by the global clock net. 2. Output timing is measured at 1.4V with 35 pF external capacitive load for LVTTL. The 35 pF load does not apply to the Min values. For other I/O standards and different loads, see the tables Constants for Calculating TIOOP and Delay Measurement Methodology, page 41. 3. DLL output jitter is already included in the timing calculation. 4. For data output with different standards, adjust delays with the values shown in IOB Output Delay Adjustments for Different Standards(1), page 40. For a global clock input with standards other than LVTTL, adjust delays with values from the I/O Standard Global Clock Input Adjustments, page 42. Global Clock Input to Output Delay for LVTTL, without DLL (Pin-to-Pin)(1) Speed Grade All -7 -6 Symbol Description Device Min Max Max Units TICKOF LVTTL global clock input to output delay using output flip-flop for LVTTL, 12 mA, fast slew rate, without DLL. XC2S50E 1.5 4.4 4.6 ns XC2S100E 1.5 4.4 4.6 ns XC2S150E 1.5 4.5 4.7 ns XC2S200E 1.5 4.5 4.7 ns XC2S300E 1.5 4.5 4.7 ns XC2S400E 1.5 4.6 4.8 ns XC2S600E 1.6 4.7 4.9 ns Notes: 1. Listed above are representative values where one global clock input drives one vertical clock line in each accessible column, and where all accessible IOB and CLB flip-flops are clocked by the global clock net. 2. Output timing is measured at 1.4V with 35 pF external capacitive load for LVTTL. The 35 pF load does not apply to the Min values. For other I/O standards and different loads, see the tables Constants for Calculating TIOOP and Delay Measurement Methodology, page 41. 3. For data output with different standards, adjust delays with the values shown in IOB Output Delay Adjustments for Different Standards(1), page 40. For a global clock input with standards other than LVTTL, adjust delays with values from the I/O Standard Global Clock Input Adjustments, page 42. DS077-3 (v2.3) June 18, 2008 Product Specification www.xilinx.com 35 R Spartan-IIE FPGA Family: DC and Switching Characteristics Global Clock Setup and Hold for LVTTL Standard, with DLL (Pin-to-Pin) Speed Grade -7 -6 Symbol Description Min Min Units TPSDLL / TPHDLL Input setup and hold time relative to global clock input signal for LVTTL standard, no delay, IFF,(1) with DLL 1.6 / 0 1.7 / 0 ns Notes: 1. IFF = Input Flip-Flop or Latch 2. Setup time is measured relative to the Global Clock input signal with the fastest route and the lightest load. Hold time is measured relative to the Global Clock input signal with the slowest route and heaviest load. 3. DLL output jitter is already included in the timing calculation. 4. For data input with different standards, adjust the setup time delay by the values shown in IOB Input Delay Adjustments for Different Standards, page 38. For a global clock input with standards other than LVTTL, adjust delays with values from the I/O Standard Global Clock Input Adjustments, page 42. 5. A zero hold time listing indicates no hold time or a negative hold time. Global Clock Setup and Hold for LVTTL Standard, without DLL (Pin-to-Pin) Speed Grade -7 -6 Symbol Description Device Min Min Units TPSFD / TPHFD Input setup and hold time relative to global clock input signal for LVTTL standard, with delay, IFF,(1) without DLL XC2S50E 1.8 / 0 1.8 / 0 ns XC2S100E 1.8 / 0 1.8 / 0 ns XC2S150E 1.9 / 0 1.9 / 0 ns XC2S200E 1.9 / 0 1.9 / 0 ns XC2S300E 2.0 / 0 2.0 / 0 ns XC2S400E 2.0 / 0 2.0 / 0 ns XC2S600E 2.1 / 0 2.1 / 0 ns Notes: 1. IFF = Input Flip-Flop or Latch 2. Setup time is measured relative to the Global Clock input signal with the fastest route and the lightest load. Hold time is measured relative to the Global Clock input signal with the slowest route and heaviest load. 3. For data input with different standards, adjust the setup time delay by the values shown in IOB Input Delay Adjustments for Different Standards, page 38. For a global clock input with standards other than LVTTL, adjust delays with values from the I/O Standard Global Clock Input Adjustments, page 42. 36 www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics IOB Input Switching Characteristics (1) Input delays associated with the pad are specified for LVTTL levels. For other standards, adjust the delays with the values shown in IOB Input Delay Adjustments for Different Standards, page 38. Speed Grade -7 Symbol Description -6 Device Min Max Min Max Units Propagation Delays TIOPI Pad to I output, no delay All 0.4 0.8 0.4 0.8 ns TIOPID Pad to I output, with delay All 0.5 1.0 0.5 1.0 ns TIOPLI Pad to output IQ via transparent latch, no delay All 0.7 1.5 0.7 1.6 ns TIOPLID Pad to output IQ via transparent latch, with delay XC2S50E 1.3 3.0 1.3 3.1 ns XC2S100E 1.3 3.0 1.3 3.1 ns XC2S150E 1.3 3.2 1.3 3.3 ns XC2S200E 1.3 3.2 1.3 3.3 ns XC2S300E 1.3 3.2 1.3 3.3 ns XC2S400E 1.4 3.2 1.4 3.4 ns XC2S600E 1.5 3.5 1.5 3.7 ns All 0.1 0.7 0.1 0.7 ns All 1.4 / 0 - 1.5 / 0 - ns XC2S50E 2.9 / 0 - 2.9 / 0 - ns XC2S100E 2.9 / 0 - 2.9 / 0 - ns XC2S150E 3.1 / 0 - 3.1 / 0 - ns XC2S200E 3.1 / 0 - 3.1 / 0 - ns XC2S300E 3.1 / 0 - 3.1 / 0 - ns XC2S400E 3.2 / 0 - 3.2 / 0 - ns XC2S600E 3.5 / 0 - 3.5 / 0 - ns All 0.7 / 0.01 - 0.7 / 0.01 - ns Sequential Delays TIOCKIQ Clock CLK to output IQ Setup/Hold Times with Respect to Clock CLK TIOPICK / TIOICKP Pad, no delay TIOPICKD / TIOICKPD Pad, with delay TIOICECK / TIOCKICE ICE input Set/Reset Delays TIOSRCKI SR input (IFF, synchronous) All 0.9 - 1.0 - ns TIOSRIQ SR input to IQ (asynchronous) All 0.5 1.2 0.5 1.4 ns TGSRQ GSR to output IQ All 3.8 8.5 3.8 9.7 ns Notes: 1. Input timing for LVTTL is measured at 1.4V. For other I/O standards, see the table Delay Measurement Methodology, page 41. DS077-3 (v2.3) June 18, 2008 Product Specification www.xilinx.com 37 R Spartan-IIE FPGA Family: DC and Switching Characteristics IOB Input Delay Adjustments for Different Standards Input delays associated with the pad are specified for LVTTL. For other standards, adjust the delays by the values shown. A delay adjusted in this way constitutes a worst-case limit. Speed Grade Symbol Description Standard -7 -6 Units LVTTL 0 0 ns LVCMOS2 0 0 ns LVCMOS18 0.20 0.20 ns LVDS 0.15 0.15 ns TILVPECL LVPECL 0.15 0.15 ns TIPCI33_3 PCI, 33 MHz, 3.3V 0.08 0.08 ns TIPCI66_3 PCI, 66 MHz, 3.3V -0.11 -0.11 ns TIGTL GTL 0.14 0.14 ns TIGTLP GTL+ 0.14 0.14 ns TIHSTL HSTL 0.04 0.04 ns TISSTL2 SSTL2 0.04 0.04 ns TISSTL3 SSTL3 0.04 0.04 ns TICTT CTT 0.10 0.10 ns TIAGP AGP 0.04 0.04 ns Data Input Delay Adjustments TILVTTL TILVCMOS2 TILVCMOS18 TILVDS 38 Standard-specific data input delay adjustments www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics IOB Output Switching Characteristics Output delays terminating at a pad are specified for LVTTL with 12 mA drive and fast slew rate. For other standards, adjust the delays with the values shown in IOB Output Delay Adjustments for Different Standards(1), page 40. Speed Grade -7 Symbol Description -6 Min Max Min Max Units Propagation Delays TIOOP O input to pad 1.0 2.7 1.0 2.9 ns TIOOLP O input to pad via transparent latch 1.2 3.1 1.2 3.4 ns TIOTHZ T input to pad high impedance (1) 0.7 1.7 0.7 1.9 ns TIOTON T input to valid data on pad 1.1 2.9 1.1 3.1 ns 0.8 2.0 0.8 2.2 ns 3-state Delays impedance via transparent latch (1) TIOTLPHZ T input to pad high TIOTLPON T input to valid data on pad via transparent latch 1.2 3.2 1.2 3.4 ns TGTS impedance (1) 1.9 4.6 1.9 4.9 ns GTS to pad high Sequential Delays TIOCKP Clock CLK to pad 0.9 2.8 0.9 2.9 ns TIOCKHZ Clock CLK to pad high impedance (synchronous)(1) 0.7 2.0 0.7 2.2 ns TIOCKON Clock CLK to valid data on pad (synchronous) 1.1 3.2 1.1 3.4 ns 1.0 / 0 - 1.1 / 0 - ns TIOOCECK / TIOCKOCE OCE input 0.7 / 0 - 0.7 / 0 - ns TIOSRCKO / TIOCKOSR SR input (OFF) 0.9 / 0 - 1.0 / 0 - ns 0.6 / 0 - 0.7 / 0 - ns TIOTCECK / TIOCKTCE 3-state setup times, TCE input 0.6 / 0 - 0.8 / 0 - ns TIOSRCKT / TIOCKTSR 3-state setup times, SR input (TFF) 0.9 / 0 - 1.0 / 0 - ns 1.2 3.3 1.2 3.5 ns 1.0 2.4 1.0 2.7 ns Setup/Hold Times with Respect to Clock CLK TIOOCK / TIOCKO TIOTCK / TIOCKT O input 3-state setup times, T input Set/Reset Delays TIOSRP SR input to pad (asynchronous) (asynchronous)(1) TIOSRHZ SR input to pad high impedance TIOSRON SR input to valid data on pad (asynchronous) 1.4 3.7 1.4 3.9 ns TIOGSRQ GSR to pad 3.8 8.5 3.8 9.7 ns Notes: 1. Three-state turn-off delays should not be adjusted. DS077-3 (v2.3) June 18, 2008 Product Specification www.xilinx.com 39 R Spartan-IIE FPGA Family: DC and Switching Characteristics IOB Output Delay Adjustments for Different Standards(1) Output delays terminating at a pad are specified for LVTTL with 12 mA drive and fast slew rate. For other standards, adjust the delays by the values shown. A delay adjusted in this way constitutes a worst-case limit. Speed Grade Symbol Description Standard -7 -6 Units LVTTL, Slow, 2 mA 14.7 14.7 ns 4 mA 7.5 7.5 ns 6 mA 4.8 4.8 ns Output Delay Adjustments (Adj) TOLVTTL_S2 TOLVTTL_S4 TOLVTTL_S6 TOLVTTL_S8 Standard-specific adjustments for output delays terminating at pads (based on standard capacitive load, CSL) 8 mA 3.0 3.0 ns TOLVTTL_S12 12 mA 1.9 1.9 ns TOLVTTL_S16 16 mA 1.7 1.7 ns TOLVTTL_S24 24 mA 1.3 1.3 ns 13.1 13.1 ns TOLVTTL_F2 LVTTL, Fast, 2 mA TOLVTTL_F4 4 mA 5.3 5.3 ns TOLVTTL_F6 6 mA 3.1 3.1 ns TOLVTTL_F8 8 mA 1.0 1.0 ns TOLVTTL_F12 12 mA 0 0 ns TOLVTTL_F16 16 mA -0.05 -0.05 ns TOLVTTL_F24 24 mA -0.20 -0.20 ns TOLVCMOS2 LVCMOS2 0.09 0.09 ns TOLVCMOS18 LVCMOS18 0.7 0.7 ns LVDS -1.2 -1.2 ns TOLVPECL LVPECL -0.41 -0.41 ns TOPCI33_3 PCI, 33 MHz, 3.3V 2.3 2.3 ns TOPCI66_3 TOLVDS PCI, 66 MHz, 3.3V -0.41 -0.41 ns TOGTL GTL 0.49 0.49 ns TOGTLP GTL+ 0.8 0.8 ns TOHSTL_I HSTL I -0.51 -0.51 ns TOHSTL_III HSTL III -0.91 -0.91 ns TOHSTL_IV HSTL IV -1.01 -1.01 ns TOSSTL2_I SSTL2 I -0.51 -0.51 ns TOSSLT2_II SSTL2 II -0.91 -0.91 ns TOSSTL3_I SSTL3 I -0.51 -0.51 ns TOSSTL3_II SSTL3 II -1.01 -1.01 ns TOCTT CTT -0.61 -0.61 ns TOAGP AGP -0.91 -0.91 ns Notes: 1. Output timing is measured at 1.4V with 35 pF external capacitive load for LVTTL. For other I/O standards and different loads, see the tables Constants for Calculating TIOOP and Delay Measurement Methodology, page 41. 40 www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics Calculation of TIOOP as a Function of Capacitance Constants for Calculating TIOOP CSL(1) (pF) FL (ns/pF) TIOOP is the propagation delay from the O Input of the IOB to the pad. The values for TIOOP are based on the standard capacitive load (CSL) for each I/O standard as listed in the table Constants for Calculating TIOOP, below. LVTTL Fast Slew Rate, 2 mA drive 35 0.41 LVTTL Fast Slew Rate, 4 mA drive 35 0.20 For other capacitive loads, use the formulas below to calculate an adjusted propagation delay, TIOOP1. LVTTL Fast Slew Rate, 6 mA drive 35 0.13 LVTTL Fast Slew Rate, 8 mA drive 35 0.079 LVTTL Fast Slew Rate, 12 mA drive 35 0.044 LVTTL Fast Slew Rate, 16 mA drive 35 0.043 LVTTL Fast Slew Rate, 24 mA drive 35 0.033 LVTTL Slow Slew Rate, 2 mA drive 35 0.41 CLOAD is the capacitive load for the design LVTTL Slow Slew Rate, 4 mA drive 35 0.20 FL LVTTL Slow Slew Rate, 6 mA drive 35 0.100 LVTTL Slow Slew Rate, 8 mA drive 35 0.086 LVTTL Slow Slew Rate, 12 mA drive 35 0.058 LVTTL Slow Slew Rate, 16 mA drive 35 0.050 LVTTL Slow Slew Rate, 24 mA drive 35 0.048 LVCMOS2 35 0.041 LVCMOS18 35 0.050 PCI 33 MHz 3.3V 10 0.050 PCI 66 MHz 3.3V 10 0.033 GTL 0 0.014 GTL+ 0 0.017 HSTL Class I 20 0.022 HSTL Class III 20 0.016 HSTL Class IV 20 0.014 SSTL2 Class I 30 0.028 SSTL2 Class II 30 0.016 SSTL3 Class I 30 0.029 SSTL3 Class II 30 0.016 TIOOP1 = TIOOP + Adj + (CLOAD - CSL) * FL Where: Adj is selected from IOB Output Delay Adjustments for Different Standards(1), page 40, according to the I/O standard used is the capacitance scaling factor Delay Measurement Methodology Meas. VREF Point Typ (2) VL(1) VH (1) LVTTL 0 3 1.4 - LVCMOS2 0 2.5 1.125 - Standard PCI33_3 Per PCI Spec - PCI66_3 Per PCI Spec - Standard GTL VREF - 0.2 VREF + 0.2 VREF 0.80 GTL+ VREF - 0.2 VREF + 0.2 VREF 1.0 HSTL Class I VREF - 0.5 VREF + 0.5 VREF 0.75 HSTL Class III VREF - 0.5 VREF + 0.5 VREF 0.90 HSTL Class IV VREF - 0.5 VREF + 0.5 VREF 0.90 SSTL3 I and II VREF - 1.0 VREF + 1.0 VREF 1.5 SSTL2 I and II VREF - 0.75 VREF + 0.75 VREF 1.25 CTT VREF - 0.2 VREF + 0.2 VREF 1.5 AGP VREF - VREF + (0.2xVCCO) (0.2xVCCO) VREF Per AGP Spec LVDS 1.2 - 0.125 1.2 + 0.125 1.2 CTT 20 0.035 1.6 AGP 10 0.037 LVPECL 1.6 - 0.3 1.6 + 0.3 Notes: 1. Input waveform switches between VL and VH. 2. Measurements are made at VREF Typ, Maximum, and Minimum. Worst-case values are reported. 3. I/O parameter measurements are made with the capacitance values shown in the following table, Constants for Calculating TIOOP. Refer to Application Note XAPP179 for appropriate terminations. 4. I/O standard measurements are reflected in the IBIS model information except where the IBIS format precludes it. DS077-3 (v2.3) June 18, 2008 Product Specification Notes: 1. I/O parameter measurements are made with the capacitance values shown above. Refer to Application Note XAPP179 for appropriate terminations. 2. I/O standard measurements are reflected in the IBIS model information except where the IBIS format precludes it. www.xilinx.com 41 R Spartan-IIE FPGA Family: DC and Switching Characteristics Clock Distribution Switching Characteristics TGPIO is specified for LVTTL levels. For other standards, adjust TGPIO with the values shown in I/O Standard Global Clock Input Adjustments. Speed Grade Symbol Description -7 -6 Max Max Units GCLK IOB and Buffer TGPIO Global clock pad to output 0.7 0.7 ns TGIO Global clock buffer I input to O output 0.45 0.5 ns I/O Standard Global Clock Input Adjustments Delays associated with a global clock input pad are specified for LVTTL levels. For other standards, adjust the delays by the values shown. A delay adjusted in this way constitutes a worst-case limit. Speed Grade Symbol Description Standard -7 -6 Units LVTTL 0 0 ns LVCMOS2 0 0 ns TGPLVCMOS18 LVCMOS18 0.2 0.2 ns TGPLVCDS LVDS 0.38 0.38 ns TGPLVPECL LVCPECL 0.38 0.38 ns TGPPCI33_3 PCI, 33 MHz, 3.3V 0.08 0.08 ns TGPPCI66_3 PCI, 66 MHz, 3.3V -0.11 -0.11 ns TGPGTL GTL 0.37 0.37 ns TGPGTLP GTL+ 0.37 0.37 ns TGPHSTL HSTL 0.27 0.27 ns TGPSSTL2 SSTL2 0.27 0.27 ns TGPSSTL3 SSTL3 0.27 0.27 ns TGPCTT CTT 0.33 0.33 ns TGPAGP AGP 0.27 0.27 ns Data Input Delay Adjustments TGPLVTTL TGPLVCMOS2 Standard-specific global clock input delay adjustments Notes: 1. Input timing for GPLVTTL is measured at 1.4V. For other I/O standards, see the table Delay Measurement Methodology, page 41. 42 www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics DLL Timing Parameters Because of the difficulty in directly measuring many internal timing parameters, those parameters are derived from benchmark timing patterns. The following guidelines reflect worst-case values across the recommended operating conditions. Speed Grade -7 Symbol Description -6 FCLKIN Min Max Min Max Units FCLKINHF Input clock frequency (CLKDLLHF) - 60 320 60 275 MHz FCLKINLF Input clock frequency (CLKDLL) - 25 160 25 135 MHz TDLLPW Input clock pulse width 25 MHz 5.0 - 5.0 - ns 50 MHz 3.0 - 3.0 - ns 100 MHz 2.4 - 2.4 - ns 150 MHz 2.0 - 2.0 - ns 200 MHz 1.8 - 1.8 - ns 250 MHz 1.5 - 1.5 - ns 300 MHz 1.3 - NA - DLL Clock Tolerance, Jitter, and Phase Information All DLL output jitter and phase specifications were determined through statistical measurement at the package pins using a clock mirror configuration and matched drivers. Figure 22, page 44, provides definitions for various parameters in the table below. CLKDLLHF Symbol Description FCLKIN Min CLKDLL Max Min Max Units TIPTOL Input clock period tolerance - 1.0 - 1.0 ns TIJITCC Input clock jitter tolerance (cycle-to-cycle) - 150 - 300 ps > 60 MHz - 20 - 20 s 50-60 MHz - - - 25 s 40-50 MHz - - - 50 s 30-40 MHz - - - 90 s 25-30 MHz - - - 120 s - 60 - 60 ps - 100 - 100 ps - 140 - 140 ps - 160 - 160 ps - 200 - 200 ps TLOCK TOJITCC Time required for DLL to acquire lock(1) Output jitter (cycle-to-cycle) for any DLL clock output (2) CLKO (3) TPHIO Phase offset between CLKIN and TPHOO Phase offset between clock outputs on the DLL(4) TPHIOM TPHOOM Phase difference between CLKIN and CLKO (5) Phase difference between clock outputs on the DLL(6) Notes: 1. Commercial operating conditions. Add 30% for Industrial operating conditions. 2. Output Jitter is cycle-to-cycle jitter measured on the DLL output clock, excluding input clock jitter. 3. Phase Offset between CLKIN and CLKO is the worst-case fixed time difference between rising edges of CLKIN and CLKO, excluding output jitter and input clock jitter. 4. Phase Offset between Clock Outputs on the DLL is the worst-case fixed time difference between rising edges of any two DLL outputs, excluding output jitter and input clock jitter. 5. Maximum Phase Difference between CLKIN and CLKO is the sum of output jitter and phase offset between CLKIN and CLKO, or the greatest difference between CLKIN and CLKO rising edges due to DLL alone (excluding input clock jitter). 6. Maximum Phase Difference between Clock Outputs on the DLL is the sum of output jitter and phase offset between any DLL clock outputs, or the greatest difference between any two DLL output rising edges due to DLL alone (excluding input clock jitter). DS077-3 (v2.3) June 18, 2008 Product Specification www.xilinx.com 43 R Spartan-IIE FPGA Family: DC and Switching Characteristics Period Tolerance: the allowed input clock period change in nanoseconds. T CLKIN = 1 FCLKIN TCLKIN +_ TIPTOL Output Jitter: the difference between an ideal reference clock edge and the actual design. Phase Offset and Maximum Phase Difference Ideal Period Actual Period + Jitter +/- Jitter + Maximum Phase Difference + Phase Offset DS001_52_090800 Figure 22: Period Tolerance and Clock Jitter 44 www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics CLB Switching Characteristics Delays originating at F/G inputs vary slightly according to the input used. The values listed below are worst-case. Precise values are provided by the timing analyzer. Speed Grade -7 Symbol Description -6 Min Max Min Max Units Combinatorial Delays TILO 4-input function: F/G inputs to X/Y outputs 0.18 0.42 0.18 0.47 ns TIF5 5-input function: F/G inputs to F5 output 0.3 0.8 0.3 0.9 ns TIF5X 5-input function: F/G inputs to X output 0.3 0.8 0.3 0.9 ns TIF6Y 6-input function: F/G inputs to Y output via F6 MUX 0.3 0.9 0.3 1.0 ns TF5INY 6-input function: F5IN input to Y output 0.04 0.2 0.04 0.22 ns TIFNCTL Incremental delay routing through transparent latch to XQ/YQ outputs - 0.7 - 0.8 ns BY input to YB output 0.18 0.46 0.18 0.51 ns TCKO FF clock CLK to XQ/YQ outputs 0.3 0.9 0.3 1.0 ns TCKLO Latch clock CLK to XQ/YQ outputs 0.3 0.9 0.3 1.0 ns TBYYB Sequential Delays Setup/Hold Times with Respect to Clock CLK TICK / TCKI 4-input function: F/G inputs 1.0 / 0 - 1.1 / 0 - ns TIF5CK / TCKIF5 5-input function: F/G inputs 1.4 / 0 - 1.5 / 0 - ns TF5INCK / TCKF5IN 6-input function: F5IN input 0.8 / 0 - 0.8 / 0 - ns 6-input function: F/G inputs via F6 MUX 1.5 / 0 - 1.6 / 0 - ns BX/BY inputs 0.7 / 0 - 0.8 / 0 - ns CE input 0.7 / 0 - 0.7 / 0 - ns SR/BY inputs (synchronous) 0.52 / 0 - 0.6 / 0 - ns TIF6CK / TCKIF6 TDICK / TCKDI TCECK / TCKCE TRCK / TCKR Clock CLK TCH Pulse width, High 1.3 - 1.4 - ns TCL Pulse width, Low 1.3 - 1.4 - ns Pulse width, SR/BY inputs 2.1 - 2.4 - ns TRQ Delay from SR/BY inputs to XQ/YQ outputs (asynchronous) 0.3 0.9 0.3 1.0 ns FTOG Toggle frequency (for export control) - 400 - 357 MHz Set/Reset TRPW DS077-3 (v2.3) June 18, 2008 Product Specification www.xilinx.com 45 R Spartan-IIE FPGA Family: DC and Switching Characteristics CLB Arithmetic Switching Characteristics Setup times not listed explicitly can be approximated by decreasing the combinatorial delays by the setup time adjustment listed. Precise values are provided by the timing analyzer. Speed Grade -7 Symbol Description -6 Min Max Min Max Units Combinatorial Delays TOPX F operand inputs to X via XOR - 0.8 - 0.8 ns TOPXB F operand input to XB output - 0.8 - 0.9 ns TOPY F operand input to Y via XOR - 1.4 - 1.5 ns TOPYB F operand input to YB output - 1.1 - 1.3 ns TOPCYF F operand input to COUT output - 0.9 - 1.0 ns TOPGY G operand inputs to Y via XOR - 0.8 - 0.9 ns TOPGYB G operand input to YB output - 1.2 - 1.3 ns TOPCYG G operand input to COUT output - 0.9 - 1.0 ns TBXCY BX initialization input to COUT - 0.51 - 0.6 ns TCINX CIN input to X output via XOR - 0.6 - 0.7 ns TCINXB CIN input to XB - 0.07 - 0.1 ns TCINY CIN input to Y via XOR - 0.7 - 0.7 ns TCINYB CIN input to YB - 0.4 - 0.5 ns CIN input to COUT output - 0.14 - 0.15 ns TFANDXB F1/2 operand inputs to XB output via AND - 0.35 - 0.4 ns TFANDYB F1/2 operand inputs to YB output via AND - 0.7 - 0.8 ns TFANDCY F1/2 operand inputs to COUT output via AND - 0.5 - 0.6 ns TGANDYB G1/2 operand inputs to YB output via AND - 0.6 - 0.7 ns TGANDCY G1/2 operand inputs to COUT output via AND - 0.3 - 0.4 ns TBYP Multiplier Operation Setup/Hold Times with Respect to Clock CLK 46 TCCKX / TCKCX CIN input to FFX 1.2 / 0 - 1.3 / 0 - ns TCCKY / TCKCY CIN input to FFY 1.2 / 0 - 1.3 / 0 - ns www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics CLB Distributed RAM Switching Characteristics Speed Grade -7 Symbol Description Sequential Delays TSHCKO16 Clock CLK to X/Y outputs (WE active, 16 x 1 mode) TSHCKO32 Clock CLK to X/Y outputs (WE active, 32 x 1 mode) -6 Min Max Min Max Units 0.6 1.5 0.6 1.7 ns 0.8 1.9 0.8 2.1 ns Setup/Hold Times with Respect to Clock CLK TAS / TAH F/G address inputs 0.42 / 0 - 0.5 / 0 - ns TDS / TDH BX/BY data inputs (DIN) 0.53 / 0 - 0.6 / 0 - ns CE input (WS) 0.7 / 0 - 0.8 / 0 - ns Pulse width, High 2.1 - 2.4 - ns TWPL Pulse width, Low 2.1 - 2.4 - ns TWC Clock period to meet address write cycle time 4.2 - 4.8 - ns TWS / TWH Clock CLK TWPH CLB Shift Register Switching Characteristics Speed Grade -7 Symbol Description -6 Min Max Min Max Units 1.2 2.9 1.2 3.2 ns 0.53 / 0 - 0.6 / 0 - ns 0.7 / 0 - 0.8 / 0 - ns Pulse width, High 2.1 - 2.4 - ns Pulse width, Low 2.1 - 2.4 - ns Sequential Delays TREG Clock CLK to X/Y outputs Setup/Hold Times with Respect to Clock CLK TSHDICK BX/BY data inputs (DIN) TSHCECK Clock CLK TSRPH TSRPL CE input (WS) Block RAM Switching Characteristics Speed Grade -7 Symbol Description Sequential Delays TBCKO Clock CLK to DOUT output Setup/Hold Times with Respect to Clock CLK TBACK / TBCKA ADDR inputs -6 Min Max Min Max Units 0.6 3.1 0.6 3.5 ns 1.0 / 0 - 1.1 / 0 - ns TBDCK/ TBCKD DIN inputs 1.0 / 0 - 1.1 / 0 - ns TBECK/ TBCKE EN inputs 2.2 / 0 - 2.5 / 0 - ns TBRCK/ TBCKR RST input 2.1 / 0 - 2.3 / 0 - ns WEN input 2.0 / 0 - 2.2 / 0 - ns TBWCK/ TBCKW Clock CLK TBPWH Pulse width, High 1.4 - 1.5 - ns TBPWL Pulse width, Low 1.4 - 1.5 - ns TBCCS CLKA -> CLKB setup time for different ports 2.7 - 3.0 - ns DS077-3 (v2.3) June 18, 2008 Product Specification www.xilinx.com 47 R Spartan-IIE FPGA Family: DC and Switching Characteristics TBUF Switching Characteristics Speed Grade Symbol TIO Description -7 -6 Max Max Units 0 0 ns IN input to OUT output TOFF TRI input to OUT output high impedance 0.1 0.11 ns TON TRI input to valid data on OUT output 0.1 0.11 ns JTAG Test Access Port Switching Characteristics Speed Grade -7 -6 Symbol Description Setup/Hold Times with Respect to TCK TTAPTCK / TTCKTAP TMS and TDI setup times and hold times Sequential Delays TTCKTDO Output delay from clock TCK to output TDO Min Max Min Max Units 4.0 / 2.0 - 4.0 / 2.0 - ns - 11.0 - 11.0 ns TCK clock frequency - 33 - 33 MHz FTCK Configuration Switching Characteristics VCC(1) TPOR PROGRAM TPL INIT TICCK CCLK Output or Input M0, M1, M2 (Required) Valid DS001_12_102301 . All Devices Symbol Description Min Max Units TPOR Power-on reset - 2 ms TPL Program latency - 100 s TICCK CCLK output delay (Master serial mode only) 0.5 4 s TPROGRAM Program pulse width 300 - ns Notes: 1. Before configuration can begin, VCCINT and VCCO Bank 2 must reach the recommended operating voltage. Figure 23: Configuration Timing on Power-Up 48 www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics DIN TCCD TDCC TCCL CCLK TCCH TCCO DOUT (Output) DS001_16_032300 . All Devices Symbol Description DIN setup/hold TDCC / TCCD TCCO TCCH CCLK DOUT Min Max Units 5/0 - ns - 12 ns High time 5 - ns TCCL Low time 5 - ns FCC Maximum frequency - 66 MHz Figure 24: Slave Serial Mode Timing CCLK (Output) TCKDS TDSCK Serial Data In TCCO Serial DOUT (Output) DS001_17_110101 . All Devices Symbol Description TDSCK / TCKDS TCCO FCC DIN setup/hold CCLK Min Max 5/0 - ns - 12 ns -30% +45% - DOUT Frequency tolerance with respect to nominal Units Figure 25: Master Serial Mode Timing DS077-3 (v2.3) June 18, 2008 Product Specification www.xilinx.com 49 R Spartan-IIE FPGA Family: DC and Switching Characteristics CCLK CS WRITE TSMCCCS TSMCSCC TSMWCC TSMCCW TSMDCC TSMCCD DATA[7:0] TSMCKBY BUSY No Write Write No Write Write DS001_20_061200 All Devices Symbol Description Min Max Units TSMDCC / TSMCCD D0-D7 setup/hold 5/1 - ns TSMCSCC / TSMCCCS CS setup/hold 7/1 - ns WRITE setup/hold 7/1 - ns TSMCCW / TSMWCC CCLK TSMCKBY BUSY propagation delay - 12 ns FCC Frequency - 66 MHz FCCNH Frequency with no handshake - 50 MHz Figure 26: Slave Parallel (SelectMAP) Mode Write Timing CCLK CS WRITE DATA[7:0] BUSY Abort DS001_21_032300 Figure 27: Slave Parallel (SelectMAP) Mode Write Abort Waveforms 50 www.xilinx.com DS077-3 (v2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: DC and Switching Characteristics Revision History Version No. Date 1.0 11/15/01 Initial Xilinx release. 1.1 06/28/02 Added -7 speed grade and extended DLL specs to Industrial. 2.0 11/18/02 Added XC2S400E and XC2S600E. Added minimum specifications. Added reference to XAPP450 for Power-On Requirements. Removed Preliminary designation. 2.1 07/09/03 Added ICCINTQ typical values. Reduced I CCPO power-on current requirements. Relaxed TCCPO power-on ramp requirements. Added IHSPO to describe current in hot-swap applications. Updated TPSFD / TPHFD description to indicate use of delay element. 2.3 06/18/08 Updated I/O measurement thresholds. Updated all modules for continuous page, figure, and table numbering. Updated links. Synchronized all modules to v2.3. DS077-3 (v2.3) June 18, 2008 Product Specification Description www.xilinx.com 51 Spartan-IIE FPGA Family: DC and Switching Characteristics 52 www.xilinx.com R DS077-3 (v2.3) June 18, 2008 Product Specification Spartan-IIE FPGA Family: Pinout Tables R DS077-4 (2.3) June 18, 2008 0 Product Specification Introduction Pin Types This section describes how the various pins on a Spartan(R)-IIE FPGA connect within the supported component packages, and provides device-specific thermal characteristics. Spartan-IIE FPGAs are available in both standard and Pb-free, RoHS versions of each package, with the Pb-free version adding a "G" to the middle of the package code. Except for the thermal characteristics, all information for the standard package applies equally to the Pb-free package. Most pins on a Spartan-IIE FPGA are general-purpose, user-defined I/O pins. There are, however, different functional types of pins on Spartan-IIE FPGA packages, as outlined below. Pin Definitions Dedicated Pin Direction GCK0, GCK1, GCK2, GCK3 No Input Clock input pins that connect to Global Clock buffers or DLL inputs. These pins become user inputs when not needed for clocks. DLL No Input Clock input pins that connect to DLL input or feedback clocks. Differential clock input (N input of pair) when paired with adjacent GCK input. Becomes a user I/O when not needed for clocks. M0, M1, M2 Yes Input Mode pins used to specify the configuration mode. CCLK Yes Input or Output PROGRAM Yes Input DONE Yes Bidirectional Indicates that configuration loading is complete, and that the start-up sequence is in progress. The output may be open drain. INIT No Bidirectional (Open-drain) When Low, indicates that the configuration memory is being cleared. Goes High to indicate the end of initialization. Goes back Low to indicate a CRC error. This pin becomes a user I/O after configuration. DOUT/BUSY No Output In Slave Parallel mode, BUSY controls the rate at which configuration data can be loaded. It is not needed below 50 MHz. This pin becomes a user I/O after configuration unless the Slave Parallel port is retained. Pad Name Description The configuration Clock I/O pin. It is an input for Slave Parallel and Slave Serial modes, and output in Master Serial mode. After configuration, it is an input only with Don't Care logic levels. Initiates a configuration sequence when asserted Low. In serial modes, DOUT provides configuration data to downstream devices in a daisy-chain. This pin becomes a user I/O after configuration. (c) 2003-2007 Xilinx, Inc. All rights reserved. XILINX, the Xilinx logo, the Brand Window, and other designated brands included herein are trademarks of Xilinx, Inc. All other trademarks are the property of their respective owners. DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com 53 R Spartan-IIE FPGA Family: Pinout Tables Pin Definitions (Continued) Pad Name D0/DIN, D1, D2, D3, D4, D5, D6, D7 Dedicated Pin Direction Description No Input or Output In Slave Parallel mode, D0-D7 are configuration data input pins. During readback, D0-D7 are output pins. These pins become user I/Os after configuration unless the Slave Parallel port is retained. In serial modes, DIN is the single data input. This pin becomes a user I/O after configuration. WRITE No Input In Slave Parallel mode, the active-low Write Enable signal. This pin becomes a user I/O after configuration unless the Slave Parallel port is retained. CS No Input In Slave Parallel mode, the active-low Chip Select signal. This pin becomes a user I/O after configuration unless the Slave Parallel port is retained. TDI, TDO, TMS, TCK Yes Mixed Boundary Scan Test Access Port pins (IEEE 1149.1). VCCINT Yes Input 1.8V power supply pins for the internal core logic. VCCO Yes Input Power supply pins for output drivers (1.5V, 1.8V, 2.5V, or 3.3V subject to banking rules in the Functional Description module. VREF No Input Input threshold reference voltage pins. Become user I/Os when an external threshold voltage is not needed (subject to banking rules in the Functional Description module. GND Yes Input Ground. All must be connected. IRDY, TRDY No See PCI core documentation These signals can only be accessed when using Xilinx PCI cores. If the cores are not used, these pins are available as user I/Os. L#[P/N] (e.g., L0P) No Bidirectional Differential I/O with synchronous output. P = positive, N = negative. The number (#) is used to associate the two pins of a differential pair. Becomes a general user I/O when not needed for differential signals. L#[P/N]_Y (e.g., L0P_Y) No Bidirectional Differential I/O with asynchronous or synchronous output (asynchronous output not compatible for all densities in a package). P = positive, N = negative. The number (#) is used to associate the two pins of a differential pair. Becomes a general user I/O when not needed for differential signals. L#[P/N]_YY (e.g., L0P_YY) No Bidirectional Differential I/O with asynchronous or synchronous output (compatible for all densities in a package). P = positive, N = negative. The number (#) is used to associate the two pins of a differential pair. Becomes a general user I/O when not needed for differential signals. I/O No Bidirectional These pins can be configured to be input and/or output after configuration is completed. Unused I/Os are disabled with a weak pull-down resistor. After power-on and before configuration is completed, these pins are either pulled up or left floating according to the Mode pin values. See the DC and Switching Characteristics module for power-on characteristics. 54 www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables Spartan-IIE Package Pinouts The Spartan(R)-IIE family of FPGAs is available in five popular, low-cost packages, including plastic quad flat packs and fine-pitch ball grid arrays. Family members have footprint compatibility across devices provided in the same package, with minor exceptions due to the smaller number of I/O in smaller devices or due to LVDS/LVPECL pin pairing. The Spartan-IIE family is not footprint compatible with any other FPGA family. The following package-specific pinout tables indicate function, pin, and bank information for all devices available in that package. The pinouts follow the pad locations around the die, starting from pin 1 on the QFP packages. Table 12: Spartan-IIE Family Package Options Maximum I/O Lead Pitch (mm) Footprint Area (mm) Height (mm) Mass(1) (g) Thin Quad Flat Pack (TQFP) 102 0.5 22 x 22 1.60 1.4 208 Plastic Quad Flat Pack (PQFP) 146 0.5 30.6 x 30.6 3.70 5.3 FT256 / FTG256 256 Fine-pitch Thin Ball Grid Array (FBGA) 182 1.0 17 x 17 1.55 1.0 FG456 / FGG456 456 Fine-pitch Ball Grid Array (FBGA) 329 1.0 23 x 23 2.60 2.2 FG676 / FGG676 676 Fine-pitch Ball Grid Array (FBGA) 514 1.0 27 x 27 2.60 3.1 Package Leads TQ144 / TQG144 144 PQ208 / PQG208 Type Notes: 1. Package mass is 10%. Package Overview Mechanical Drawings Table 12 shows the five low-cost, space-saving production package styles for the Spartan-IIE family. Detailed mechanical drawings for each package type are available from the Xilinx web site at the specified location in Table 13. Each package style is available in an environmentally friendly lead-free (Pb-free) option. The Pb-free packages include an extra `G' in the package style name. For example, the standard "TQ144" package becomes "TQG144" when ordered as the Pb-free option. Leaded (non-Pb-free) packages may be available for selected devices, with the same pin-out and without the "G" in the ordering code; contact Xilinx(R) sales for more information. The mechanical dimensions of the standard and Pb-free packages are similar, as shown in the mechanical drawings provided in Table 13. For additional package information, see UG112: Device Package User Guide. Material Declaration Data Sheets (MDDS) are also available on the Xilinx web site for each package. Table 13: Xilinx Package Documentation Package TQ144 Drawing Package Drawing TQG144 PQ208 Package Drawing Package Drawing FGG676 DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com PK158_FT256 PK115_FTG256 Package Drawing FGG456 FG676 PK166_PQ208 PK123_PQG208 FTG256 FG456 PK169_TQ144 PK126_TQG144 PQG208 FT256 MDDS PK154_FG456 PK109_FGG456 Package Drawing PK155_FG676 PK111_FGG676 55 R Spartan-IIE FPGA Family: Pinout Tables Package Thermal Characteristics Table 14 provides the thermal characteristics for the various Spartan-II FPGA package offerings. This information is also available using the Thermal Query tool on xilinx.com (www.xilinx.com/cgi-bin/thermal/thermal.pl). The junction-to-case thermal resistance (JC) indicates the difference between the temperature measured on the package body (case) and the die junction temperature per watt of power consumption. The junction-to-board (JB) value similarly reports the difference between the board and junction temperature. The junction-to-ambient (JA) value reports the temperature difference between the ambient environment and the junction temperature. The JA value is reported at different air velocities, measured in linear feet per minute (LFM). The "Still Air (0 LFM)" column shows the JA value in a system without a fan. The thermal resistance drops with increasing air flow. Table 14: Spartan-IIE Package Thermal Characteristics Junction-to-Ambient (JA) at Different Air Flows Package Device Junction-to-Case (JC) Junction-toBoard (JB) Still Air (0 LFM) 250 LFM 500 LFM 750 LFM Units TQ144 TQG144 XC2S50E 5.8 N/A 32.3 25.1 21.5 20.1 C/Watt XC2S100E 5.3 N/A 31.4 24.4 20.8 19.6 C/Watt XC2S50E 7.1 N/A 35.1 25.9 22.9 21.2 C/Watt XC2S100E 6.1 N/A 34.2 25.2 22.3 20.7 C/Watt XC2S150E 6.0 N/A 34.1 25.2 22.2 20.6 C/Watt XC2S200E 4.6 N/A 32.4 23.9 21.2 19.6 C/Watt XC2S300E 4.0 N/A 31.6 23.3 20.6 19.1 C/Watt XC2S50E 7.3 17.8 27.4 21.6 20.4 20.0 C/Watt XC2S100E 5.8 15.1 25.0 19.5 18.2 17.8 C/Watt XC2S150E 5.7 14.8 24.8 19.3 18.0 17.6 C/Watt XC2S200E 3.9 11.4 21.9 16.6 15.2 14.7 C/Watt XC2S300E 3.2 10.1 20.8 15.6 14.2 13.7 C/Watt XC2S400E 2.5 8.8 19.7 14.5 13.2 12.6 C/Watt XC2S100E 8.4 14.9 24.3 19.2 18.1 17.4 C/Watt XC2S150E 8.2 14.6 24.1 19.0 17.9 17.1 C/Watt XC2S200E 6.3 11.6 21.0 16.1 15.0 14.3 C/Watt XC2S300E 5.6 10.4 19.9 15.1 13.9 13.2 C/Watt XC2S400E 3.6 6.5 17.7 11.7 10.5 10.0 C/Watt XC2S600E 2.7 5.0 17.3 11.2 10.0 9.5 C/Watt XC2S400E 4.1 7.9 15.6 11.1 9.8 9.2 C/Watt XC2S600E 3.4 6.9 14.5 9.9 8.6 7.9 C/Watt PQ208 PQG208 FT256 FTG256 FG456 FGG456 FG676 FGG676 56 www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables Low Voltage Differential Signals (LVDS and LVPECL) The Spartan-IIE family features low-voltage differential signaling (LVDS and LVPECL). Each signal utilizes two pins on the Spartan-IIE device, known as differential pin pairs. Each differential pin pair has a Positive (P) and a Negative (N) pin. These pairs are labeled in the following manner. I/O, L#[P/N][-/_Y/_YY] where Because of differences between densities, the differential pairs that can be used for asynchronous outputs vary by device. The pairs that are available in all densities for a given package have the _YY suffix. These pins should be used for differential asynchronous outputs if the design may later move to a different density. All other differential pairs that can be used for asynchronous outputs have the _Y suffix. To simplify the following tables, the "Pad Name" column shows the part of the name that is common across densities. The "Pad Name" column leaves out the _Y suffix and the "LVDS Asynchronous Output Option" column indicates the densities that allow asynchronous outputs for LVDS or LVPECL on the given pin. L = LVDS or LVPECL pin # = Pin pair number P = Positive N = Negative _Y = Asynchronous output allowed (device-dependent) _YY = Asynchronous output allowed (all devices) Available Differential Pairs According to Package Type Device TQ144 PQ208 FT256 FG456 FG676 XC2S50E 28 50 83 - - XC2S100E 28 50 83 86 - XC2S150E - 50 83 114 - XC2S200E - 50 83 120 - XC2S300E - 50 83 120 - XC2S400E - - 83 120 172 XC2S600E - - - 120 205 Synchronous or Asynchronous I/O pins for differential signals can either be synchronous or asynchronous, input or output. Differential signaling requires the pins of each pair to switch simultaneously. If the output signals driving the pins are from IOB flip-flops, they are synchronous. If the signals driving the pins are from internal logic, they are asynchronous, and therefore more care must be taken that they are simultaneous. Any differential pairs can be used for synchronous input and output signals as well as asynchronous input signals. However, only the differential pairs with the _Y or _YY suffix can be used for asynchronous output signals. DS077-4 (2.3) June 18, 2008 Product Specification Asynchronous Output Pad Name Designation DLL Pins Pins labeled "I/O (DLL)" can be used as general-purpose I/O or as inputs to the DLL. Adjacent DLL pins form a differential pair. They reside in two different banks, so if they are outputs the VCCO level must be the same for both banks. Each DLL pin can also be paired with the adjacent GCK clock pin for a differential clock input. The "I/O (DLL)" pin always becomes the N terminal when paired with GCK, even if it is labeled "P" for its pairing with the adjacent DLL pin. VREF Pins Pins labeled "I/O, VREF" can be used as either an I/O or a VREF pin. If any I/O pin within the bank requires a VREF input, all the VREF pins in the bank must be connected to the same voltage. See the I/O banking rules in the Functional Description module for more detail. If no pin in a given bank requires VREF, then that bank's VREF pins can be used as general I/O. To simplify the following tables, the "Pad Name" column shows the part of the name that is common across densities. When VREF is only available in limited densities, the "Pad Name" column leaves out the VREF designation and the "VREF Option" column indicates the densities that provide VREF on the given pin. VCCO Banks In the TQ144 and PQ208 packages, the eight banks have VCCO connected together. Thus, only one VCCO is allowed in these packages, although different VREF values are allowed in each of the eight banks. See I/O Banking. www.xilinx.com 57 R Spartan-IIE FPGA Family: Pinout Tables Pinout Tables The following device-specific pinout tables include all packages available for each Spartan-IIE device. They follow the pad locations around the die. In the TQ144 package, all VCCO pins must be connected to the same voltage. TQ144 Pinouts (XC2S50E and XC2S100E) (Continued) Pad Name Bank Pin LVDS Async. Output Option I/O, L22N 6 P27 XC2S50E XC2S100E I/O 6 P28 - - I/O, VREF Bank 6 6 P29 - All I/O 6 P30 - - I/O, L21P_YY 6 P31 All - I/O, L21N_YY 6 P32 All - M1 - P33 - - GND - P34 - - M0 - P35 - - VCCO - P36 - - M2 - P37 - - I/O, L20N_YY 5 P38 All - I/O, L20P_YY 5 P39 All - I/O 5 P40 - - I/O, VREF Bank 5 5 P41 - All I/O 5 P42 - - I/O, L19N_YY 5 P43 All XC2S100E I/O, L19P_YY 5 P44 All - GND - P45 - - VCCINT - P46 - - I/O, L18N_YY 5 P47 All - I/O, L18P_YY 5 P48 All - I/O, VREF Bank 5 5 P49 - All I/O (DLL), L17N 5 P50 - - VCCINT - P51 - - GCK1, I 5 P52 - - VCCO 5 P53 - - GND - P54 - - GCK0, I 4 P55 - - TQ144 Pinouts (XC2S50E and XC2S100E) Function Pad Name Bank Pin LVDS Async. Output Option GND - P1 - - TMS - P2 - - I/O 7 P3 - - I/O 7 P4 - - I/O, VREF Bank 7 7 P5 - All I/O 7 P6 - - I/O, L27P 7 P7 XC2S50E XC2S100E I/O, L27N 7 P8 XC2S50E - GND - P9 - - I/O, L26P_YY 7 P10 All - I/O, L26N_YY 7 P11 All - I/O, VREF Bank 7, L25P 7 P12 XC2S50E All I/O, L25N 7 P13 XC2S50E - I/O 7 P14 - - I/O (IRDY) 7 P15 - - GND - P16 - - VCCO - P17 - - Function VREF Option I/O (TRDY) 6 P18 - - VCCINT - P19 - - I/O 6 P20 - - I/O, L24P 6 P21 XC2S50E - I/O, VREF Bank 6, L24N 6 P22 XC2S50E All I/O, L23P_YY 6 P23 All - I/O, L23N_YY 6 P24 All - GND - P25 - - I/O, L22P 6 P26 XC2S50E - 58 www.xilinx.com VREF Option DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables TQ144 Pinouts (XC2S50E and XC2S100E) (Continued) Pad Name Function Bank Pin LVDS Async. Output Option I/O (DLL), L17P 4 P56 - - I/O 4 P57 - - I/O, VREF Bank 4 4 P58 - All I/O, L16N_YY 4 P59 All I/O, L16P_YY 4 P60 VCCINT - GND TQ144 Pinouts (XC2S50E and XC2S100E) (Continued) Bank Pin LVDS Async. Output Option I/O, VREF Bank 3, L10N 3 P85 XC2S50E All I/O (D4), L10P 3 P86 XC2S50E - I/O 3 P87 - - - VCCINT - P88 - - All - I/O (TRDY) 3 P89 - - P61 - - VCCO - P90 - - - P62 - - GND - P91 - - I/O, L15N_YY 4 P63 All - I/O, L15P_YY 4 P64 All XC2S100E I/O (IRDY) 2 P92 - - I/O 4 P65 - - I/O 2 P93 - - I/O, VREF Bank 4 4 P66 - All I/O (D3), L9N 2 P94 XC2S50E - P95 XC2S50E All 4 P67 - - I/O, VREF Bank 2, L9P 2 I/O I/O, L14N_YY 4 P68 All - I/O 2 P96 - - I/O, L14P_YY 4 P69 All - I/O, L8N_YY 2 P97 All - GND - P70 - - I/O (D2), L8P_YY 2 P98 All - DONE 3 P71 - - GND - P99 - - VCCO - P72 - - I/O (D1), L7N 2 P100 XC2S50E - PROGRAM - P73 - - I/O, L7P 2 P101 XC2S50E XC2S100E I/O (INIT), L13N_YY 3 P74 All - I/O 2 P102 - - 2 P103 - All I/O (D7), L13P_YY 3 I/O, VREF Bank 2 I/O 2 P104 - - I/O 3 P76 - - 2 P105 All - I/O, VREF Bank 3 3 P77 - All I/O (DIN, D0), L6N_YY 2 P106 All - I/O 3 P78 - - I/O (DOUT, BUSY), L6P_YY I/O, L12N 3 P79 XC2S50E XC2S100E CCLK 2 P107 - - I/O (D6), L12P 3 P80 XC2S50E - VCCO - P108 - - GND - P81 - - TDO 2 P109 - - I/O (D5), L11N_YY 3 P82 All - GND - P110 - - I/O, L11P_YY 3 P83 All - TDI - P111 - - I/O 3 P84 - - DS077-4 (2.3) June 18, 2008 Product Specification P75 All Pad Name VREF Option - Function www.xilinx.com VREF Option 59 R Spartan-IIE FPGA Family: Pinout Tables TQ144 Pinouts (XC2S50E and XC2S100E) (Continued) Pad Name Function Bank Pin LVDS Async. Output Option TQ144 Pinouts (XC2S50E and XC2S100E) (Continued) Pad Name Bank Pin LVDS Async. Output Option I/O 0 P139 - - VREF Option Function VREF Option I/O (CS), L5P_YY 1 P112 All - I/O, VREF Bank 0 0 P140 - All I/O (WRITE), L5N_YY 1 P113 All - I/O 0 P141 - - I/O 0 P142 - - I/O 1 P114 - - TCK - P143 - - I/O, VREF Bank 1 1 P115 - All VCCO - P144 - - I/O 1 P116 - - I/O, L4P_YY 1 P117 All XC2S100E I/O, L4N_YY 1 P118 All - GND - P119 - - VCCINT - P120 - - I/O, L3P_YY 1 P121 All - I/O, L3N_YY 1 P122 All - I/O, VREF Bank 1 1 P123 - All I/O 1 P124 - - I/O (DLL), L2P 1 P125 - - GCK2, I 1 P126 - - GND - P127 - - VCCO - P128 - - GCK3, I 0 P129 - - VCCINT - P130 - - I/O (DLL), L2N 0 P131 - - I/O, VREF Bank 0 0 P132 - All I/O, L1P_YY 0 P133 All - I/O, L1N_YY 0 P134 All - VCCINT - P135 - - GND - P136 - - I/O, L0P_YY 0 P137 All - I/O, L0N_YY 0 P138 All XC2S100E 60 TQ144 Differential Clock Pins P Clock N Bank Pin Name Pin Name GCK0 4 P55 GCK0, I P56 I/O (DLL), L17P GCK1 5 P52 GCK1, I P50 I/O (DLL), L17N GCK2 1 P126 GCK2, I P125 I/O (DLL), L2P GCK3 0 P129 GCK3, I P131 I/O (DLL), L2N www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables In the PQ208 package, all VCCO pins must be connected to the same voltage. PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Pad Name Bank Pin LVDS Async. Output Option I/O 7 P22 - - I/O, L44P_YY 7 P23 All - I/O (IRDY), L44N_YY 7 P24 All - GND - P25 - - VCCO - P26 - - I/O (TRDY) 6 P27 - - VCCINT - P28 - - I/O 6 P29 - - I/O, L43P 6 P30 XC2S50E, 300E - I/O, VREF Bank 6, L43N 6 P31 XC2S50E, 300E All GND - P32 - - I/O, L42P_YY 6 P33 All - I/O, L42N_YY 6 P34 All - I/O, L41P_YY 6 P35 All - I/O, L41N_YY 6 P36 All - VCCINT - P37 - - VCCO - P38 - - GND - P39 - - I/O, L40P 6 P40 XC2S50E, 300E - I/O, L40N 6 P41 XC2S50E, 300E XC2S100E, 150E, 200E, 300E I/O 6 P42 - - I/O 6 P43 - - I/O 6 P44 - - PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Pad Name Bank Pin LVDS Async. Output Option GND - P1 - - TMS - P2 - - I/O 7 P3 - - I/O 7 P4 - XC2S200E, 300E I/O 7 P5 - - I/O, VREF Bank 7, L49P 7 P6 XC2S50E, 150E, 200E, 300E All I/O, L49N 7 P7 XC2S50E, 150E, 200E, 300E - I/O 7 P8 - - I/O 7 P9 - - I/O, L48P 7 P10 XC2S50E, 300E XC2S100E, 150E, 200E, 300E Function Function VREF Option I/O, L48N 7 P11 XC2S50E, 300E - GND - P12 - - VCCO - P13 - - VCCINT - P14 - - I/O, L47P_YY 7 P15 All - I/O, L47N_YY 7 P16 All - I/O, L46P_YY 7 P17 All - I/O, L46N_YY 7 P18 All - GND - P19 - - I/O, VREF Bank 7, L45P 7 P20 XC2S50E, 300E All I/O, L45N 7 XC2S50E, 300E - P21 DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com VREF Option 61 R Spartan-IIE FPGA Family: Pinout Tables PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Pad Name Function Bank Pin I/O, VREF Bank 6, L39P 6 P45 I/O, L39N 6 I/O LVDS Async. Output Option PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Pad Name VREF Option XC2S100E, 150E All P46 XC2S100E, 150E - 6 P47 - XC2S200E, 300E I/O, L38P_YY 6 P48 All - I/O, L38N_YY 6 P49 All - M1 - P50 - - GND - P51 - - M0 - P52 - - VCCO - P53 - - M2 - P54 - - I/O, L37N_YY 5 P55 All - I/O, L37P_YY 5 P56 All - I/O 5 P57 - XC2S200E, 300E I/O 5 P58 - - I/O, VREF Bank 5, L36N_YY 5 P59 All All I/O, L36P_YY 5 P60 All - I/O, L35N 5 P61 XC2S50E, 100E, 300E - I/O, L35P 5 P62 XC2S50E, 100E, 300E - I/O, L34N 5 P63 XC2S50E, 100E, 200E, 300E XC2S100E, 150E, 200E, 300E XC2S50E, 100E, 200E, 300E - - - I/O, L34P GND 62 5 - P64 P65 Bank Pin LVDS Async. Output Option VCCO - P66 - - VCCINT - P67 - - I/O, L33N 5 P68 XC2S50E, 100E, 200E, 300E - I/O, L33P 5 P69 XC2S50E, 100E, 200E, 300E - I/O 5 P70 - - I/O, L32N 5 P71 XC2S100E, 150E - GND - P72 - - I/O, VREF Bank 5, L32P 5 P73 XC2S100E, 150E All I/O 5 P74 - - I/O (DLL), L31N 5 P75 - - VCCINT - P76 - - GCK1, I 5 P77 - - VCCO - P78 - - GND - P79 - - GCK0, I 4 P80 - - I/O (DLL), L31P 4 P81 - - I/O 4 P82 - - I/O, L30N 4 P83 XC2S50E, 200E, 300E - I/O, VREF Bank 4, L30P 4 P84 XC2S50E, 200E, 300E All GND - P85 - - I/O, L29N 4 P86 XC2S50E, 200E, 300E - I/O, L29P 4 P87 XC2S50E, 200E, 300E - I/O, L28N 4 P88 XC2S50E, 100E, 200E, 300E - Function www.xilinx.com VREF Option DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Pad Name Function LVDS Async. Output Option PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Pad Name VREF Option Bank Pin I/O, L28P 4 P89 XC2S50E, 100E, 200E, 300E - VCCINT - P90 - - VCCO - P91 - - GND - P92 - - I/O, L27N 4 P93 XC2S50E, 100E, 200E, 300E - XC2S50E, 100E, 200E, 300E XC2S100E, 150E, 200E, 300E I/O, L27P 4 P94 Function LVDS Async. Output Option VREF Option Bank Pin I/O, VREF Bank 3, L23N 3 P111 XC2S50E, 150E, 200E, 300E All I/O, L23P 3 P112 XC2S50E, 150E, 200E, 300E - I/O 3 P113 - - I/O 3 P114 - - I/O, L22N 3 P115 XC2S50E, 300E XC2S100E, 150E, 200E, 300E I/O (D6), L22P 3 P116 XC2S50E, 300E - GND - P117 - - VCCO - P118 - - VCCINT - P119 - - I/O (D5), L21N_YY 3 P120 All - I/O 4 P95 - - I/O 4 P96 - - I/O, L26N_YY 4 P97 All - I/O, VREF Bank 4, L26P_YY 4 P98 All All P121 All - 4 P99 - - I/O, L21P_YY 3 I/O I/O 4 P100 - XC2S200E, 300E I/O, L20N_YY 3 P122 All - I/O, L25N_YY 4 P101 All - I/O, L20P_YY 3 P123 All - I/O, L25P_YY 4 P102 All - GND - P124 - - P125 P103 - - XC2S50E, 300E All - I/O, VREF Bank 3, L19N 3 GND DONE 3 P104 - - I/O (D4), L19P 3 P126 XC2S50E, 300E - VCCO - P105 - - I/O 3 P127 - - PROGRAM - P106 - - VCCINT - P128 - - I/O (INIT), L24N_YY 3 P107 All - I/O (TRDY) 3 P129 - - I/O (D7), L24P_YY 3 P108 All - VCCO - P130 - - GND - P131 - - I/O 3 P109 - XC2S200E, 300E P132 All - 3 P110 - - I/O (IRDY), L18N_YY 2 I/O I/O, L18P_YY 2 P133 All - DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com 63 R Spartan-IIE FPGA Family: Pinout Tables PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Pad Name PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Bank Pin LVDS Async. Output Option Bank Pin LVDS Async. Output Option I/O 2 P134 - - VCCO - P156 - - I/O (D3), L17N 2 P135 XC2S50E, 300E - TDO 2 P157 - - I/O, VREF Bank 2, L17P 2 P136 XC2S50E, 300E All GND - P158 - - TDI - P159 - - GND - P137 - - I/O (CS), L11P_YY 1 P160 All - I/O, L16N_YY 2 P138 All - I/O (WRITE), L11N_YY 1 P161 All - I/O, L16P_YY 2 P139 All - I/O, L15N_YY 2 P140 All - I/O 1 P162 - XC2S200E, 300E I/O (D2), L15P_YY 2 P141 All - I/O 1 P163 - - I/O, VREF Bank 1, L10P_YY 1 P164 All All VCCINT - P142 - - VCCO - P143 - - GND - P144 - I/O, L10N_YY 1 P165 All - - I/O (D1), L14N 2 P145 XC2S50E, 300E - I/O 1 P166 - - I/O, L14P 2 I/O 1 P167 - - P146 XC2S50E, 300E XC2S100E, 150E, 200E, 300E I/O, L9P 1 P168 XC2S50E, 100E, 200E, 300E XC2S100E, 150E, 200E, 300E I/O 2 P147 - - I/O, L9N 1 P169 2 P148 - - I/O 2 P149 - - XC2S50E, 100E, 200E, 300E - I/O I/O, VREF Bank 2, L13N 2 P150 XC2S100E, 150E All GND - P170 - - VCCO - P171 - - VCCINT - P172 - - I/O, L13P 2 P151 XC2S100E, 150E - I/O, L8P 1 P173 - I/O 2 P152 - XC2S200E, 300E XC2S50E, 100E, 200E, 300E I/O, L8N 1 P174 2 P153 All - XC2S50E, 100E, 200E, 300E - I/O (DIN, D0), L12N_YY I/O, L7P 1 P175 2 P154 All - XC2S50E, 200E, 300E - I/O (DOUT, BUSY), L12P_YY I/O, L7N 1 P176 XC2S50E, 200E, 300E - CCLK 2 GND - P177 - - Function 64 P155 - Pad Name VREF Option - Function www.xilinx.com VREF Option DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Pad Name LVDS Async. Output Option PQ208 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E) Pad Name VREF Option Function Bank Pin I/O, VREF Bank 1, L6P 1 P178 XC2S50E, 200E, 300E All I/O, L6N 1 P179 XC2S50E, 200E, 300E - I/O 1 P180 - - I/O (DLL), L5P 1 P181 - - GCK2, I 1 P182 - - GND - P183 - - VCCO - P184 - - GCK3, I 0 P185 - - VCCINT - P186 - - I/O (DLL), L5N 0 P187 - - I/O, L4P 0 P188 XC2S50E, 200E, 300E - XC2S50E, 200E, 300E All P189 Bank Pin LVDS Async. Output Option I/O 0 P201 - - I/O, L0P_YY 0 P202 All - I/O, VREF Bank 0, L0N_YY 0 P203 All All I/O 0 P204 - - I/O 0 P205 - XC2S200E, 300E I/O 0 P206 - - TCK - P207 - - VCCO - P208 - - Function VREF Option PQ208 Differential Clock Pins P N Clock Bank Pin Name Pin Name GCK0 4 P80 GCK0, I P81 I/O (DLL), L31P GCK1 5 P77 GCK1, I P75 I/O (DLL), L31N I/O, VREF Bank 0, L4N 0 GND - P190 - - I/O, L3P 0 P191 XC2S50E, 200E, 300E - GCK2 1 P182 GCK2, I P181 I/O (DLL), L5P I/O, L3N 0 P192 XC2S50E, 200E, 300E - GCK3 0 P185 GCK3, I P187 I/O (DLL), L5N I/O, L2P 0 P193 XC2S50E, 100E, 200E, 300E - I/O, L2N 0 P194 XC2S50E, 100E, 200E, 300E - VCCINT - P195 - - VCCO - P196 - - GND - P197 - - I/O, L1P 0 P198 XC2S50E, 100E, 200E, 300E - I/O, L1N 0 P199 XC2S50E, 100E, 200E, 300E XC2S100E, 150E, 200E, 300E I/O 0 P200 - - DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com 65 R Spartan-IIE FPGA Family: Pinout Tables FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) Pad Name Pad Name Bank Pin LVDS Async. Output Option TMS - B1 - - I/O 7 D3 - - I/O, L83P 7 C2 XC2S100E, 150E - Function VREF Option Function LVDS Async. Output Option VREF Option Bank Pin I/O, L74P 7 H4 XC2S100E, 150E, 200E - I/O, L74N 7 H3 XC2S100E, 150E, 200E XC2S400E I/O, L73P_YY 7 H2 All - I/O (IRDY), L73N_YY 7 H1 All - I/O (TRDY) 6 J4 - - I/O, L83N 7 C1 XC2S100E, 150E XC2S200E, 300E, 400E I/O, L82P_YY 7 D2 All - I/O, L82N_YY 7 D1 All - I/O, VREF Bank 7, L81P 7 E3 XC2S50E, 150E, 200E, 300E, 400E All I/O, L72P 6 J2 XC2S100E, 150E, 200E, 400E XC2S400E I/O, L81N 7 E4 XC2S50E, 150E, 200E, 300E, 400E - I/O, L72N 6 J3 XC2S100E, 150E, 200E, 400E - I/O, L80P 7 E2 XC2S200E, 400E - I/O, L71P 6 J1 XC2S50E, 300E, 400E - I/O, L80N 7 E1 XC2S200E, 400E - I/O, VREF Bank 6, L71N 6 K1 XC2S50E, 300E, 400E All I/O, L79P 7 F4 XC2S50E, XC2S100E, 300E, 400E 150E, 200E, 300E, 400E I/O, L70P_YY 6 K2 All - I/O, L70N_YY 6 K3 All - I/O, L69P 6 L1 XC2S100E, 150E, 400E - I/O, L69N 6 L2 XC2S100E, 150E, 400E - I/O, L79N 7 F3 XC2S50E, 300E, 400E - I/O, L78P_YY 7 F2 All - I/O, L78N_YY 7 F1 All - I/O, L68P_YY 6 K4 All - I/O, L77P 7 F5 XC2S100E, 150E - I/O, L68N_YY 6 K5 All - I/O, L77N 7 G5 XC2S100E, 150E - I/O, L67P 6 L3 XC2S50E, 300E, 400E - I/O, L76P_YY 7 G3 All - I/O, L67N 6 M2 I/O, L76N_YY 7 G4 All - XC2S50E, XC2S100E, 300E, 400E 150E, 200E, 300E, 400E I/O, VREF Bank 7, L75P 7 G2 XC2S50E, 300E, 400E All I/O, L66P 6 M1 XC2S150E, 200E, 400E - I/O, L75N 7 G1 XC2S50E, 300E, 400E - I/O, L66N 6 N1 XC2S150E, 200E, 400E - 66 www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) Pad Name LVDS Async. Output Option FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) Pad Name VREF Option Bank Pin I/O, L65P 6 L4 XC2S50E, 150E, 200E, 300E, 400E - I/O, VREF Bank 6, L65N 6 L5 XC2S50E, 150E, 200E, 300E, 400E I/O, L64P_YY 6 M3 I/O, L64N_YY 6 I/O, L63P LVDS Async. Output Option VREF Option Bank Pin I/O, L57P 5 P6 XC2S50E, 100E, 150E, 300E All I/O, L56N 5 R6 XC2S50E, XC2S100E, 100E, 200E, 150E, 200E, 300E, 400E 300E, 400E All - I/O, L56P 5 T6 - M4 All - XC2S50E, 100E, 200E, 300E, 400E 6 N2 XC2S100E, 200E, 300E - I/O, L55N 5 M6 - I/O, L63N 6 N3 XC2S100E, 200E, 300E XC2S200E, 300E, 400E XC2S50E, 100E, 200E, 300E, 400E I/O, L55P 5 N7 6 P1 All - I/O, L62N_YY 6 P2 All - XC2S50E, 100E, 200E, 300E, 400E - I/O, L62P_YY M1 - R1 - - I/O 5 P7 - - M0 - T2 - - I/O, L54N 5 R7 - M2 - R3 - - XC2S50E, 200E, 300E, 400E I/O, L54P 5 T7 XC2S50E, 200E, 300E, 400E - I/O, VREF Bank 5, L53N 5 M7 XC2S50E, 200E, 300E, 400E All I/O, L53P 5 N8 XC2S50E, 200E, 300E, 400E - I/O 5 P8 - XC2S400E I/O (DLL), L52N 5 R8 - - GCK1, I 5 T8 - - GCK0, I 4 T9 - - I/O (DLL), L52P 4 R9 - - I/O, L51N 4 P9 XC2S50E, 150E, 200E, 400E XC2S400E Function I/O, L61N_YY 5 P4 All - I/O, L61P_YY 5 R4 All - I/O, L60N 5 T3 XC2S50E, XC2S200E, 100E, 200E, 300E, 400E 300E, 400E I/O, L60P 5 T4 XC2S50E, 100E, 200E, 300E, 400E - I/O, L59N_YY 5 N5 All - I/O, L59P_YY 5 P5 All - I/O, VREF Bank 5, L58N_YY 5 R5 All All I/O, L58P_YY 5 T5 All - I/O, L57N 5 N6 XC2S50E, 100E, 150E, 300E - DS077-4 (2.3) June 18, 2008 Product Specification Function www.xilinx.com - 67 R Spartan-IIE FPGA Family: Pinout Tables FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) Pad Name LVDS Async. Output Option Pad Name VREF Option Bank Pin I/O, L51P 4 N9 XC2S50E, 150E, 200E, 400E - I/O, L50N 4 T10 XC2S50E, 200E, 300E, 400E - Function I/O, VREF Bank 4, L50P 4 R10 XC2S50E, 200E, 300E, 400E All I/O, L49N 4 P10 XC2S50E, 200E, 300E, 400E - XC2S50E, 200E, 300E, 400E - I/O, L49P 4 R11 I/O 4 T11 - - I/O, L48N 4 N10 XC2S50E, 100E, 200E, 300E, 400E - I/O, L48P 4 M10 XC2S50E, 100E, 200E, 300E, 400E - I/O, L47N 4 P11 XC2S50E, 100E, 200E, 300E, 400E - I/O, L47P 4 R12 XC2S50E, XC2S100E, 100E, 200E, 150E, 200E, 300E, 400E 300E, 400E I/O, L46N 4 T12 XC2S50E, 100E, 150E, 300E - XC2S50E, 100E, 150E, 300E - I/O, L46P 4 T13 I/O, L45N_YY 4 N11 All - I/O, VREF Bank 4, L45P_YY 4 M11 All All I/O, L44N_YY 4 P12 All - I/O, L44P_YY 4 N12 All - 68 FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) LVDS Async. Output Option VREF Option Bank Pin I/O, L43N 4 R13 XC2S50E, 150E XC2S200E, 300E, 400E I/O, L43P 4 P13 XC2S50E, 150E - I/O, L42N_YY 4 T14 All - I/O, L42P_YY 4 R14 All - DONE 3 T15 - - PROGRAM - R16 - - I/O (INIT), L41N_YY 3 P15 All - I/O (D7), L41P_YY 3 P16 All - I/O, L40N 3 N15 XC2S100E, 150E, 400E - I/O, L40P 3 N16 XC2S100E, XC2S200E, 150E, 400E 300E, 400E I/O, L39N 3 N14 XC2S50E, 100E, 150E, 200E, 300E(1) - I/O, L39P 3 M14 XC2S50E, 100E, 150E, 200E, 300E(1) - I/O, VREF Bank 3, L38N 3 M15 XC2S50E, 150E, 200E, 300E, 400E All I/O, L38P 3 M16 XC2S50E, 150E, 200E, 300E, 400E - I/O(2) 3 M13 - - I/O(2) 3 L14 - - I/O, L36N 3 L15 XC2S50E, XC2S100E, 300E, 400E 150E, 200E, 300E, 400E I/O (D6), L36P 3 L16 XC2S50E, 300E, 400E Function www.xilinx.com - DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) Pad Name Bank Pin LVDS Async. Output Option I/O (D5), L35N_YY 3 L13 All I/O, L35P_YY 3 K14 I/O, L34N 3 I/O, L34P I/O, L33N Function I/O, L33P FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) Pad Name VREF Option LVDS Async. Output Option VREF Option Function Bank Pin - I/O, VREF Bank 2, L28P 2 F16 XC2S50E, 300E, 400E All All - I/O, L27N 2 H13 - K15 XC2S100E, 150E, 400E - XC2S50E, 100E, 150E, 200E, 300E(1) 3 K16 XC2S100E, 150E, 400E - I/O, L27P 2 G14 - 3 L12 XC2S50E, 100E, 150E, 200E, 300E(1) - XC2S50E, 100E, 150E, 200E, 300E(2) I/O, L26N 2 F15 XC2S100E, 150E, 400E - XC2S50E, 100E, 150E, 200E, 300E(1) - I/O, L26P 2 E16 XC2S100E, 150E, 400E - I/O, L25N_YY 2 G13 All - I/O (D2), L25P_YY 2 F14 All - 3 K12 I/O, VREF Bank 3, L32N 3 K13 XC2S50E, 300E, 400E All I/O (D4), L32P 3 J14 XC2S50E, 300E, 400E - I/O (D1), L24N 2 E15 XC2S50E, 300E, 400E I/O, L31N 3 J15 XC2S100E, 150E, 200E, 400E - I/O, L24P 2 D16 XC2S50E, XC2S100E, 300E, 400E 150E, 200E, 300E, 400E I/O, L31P 3 J16 XC2S100E, 150E, 200E, 400E XC2S400E I/O, L23N 2 F13 XC2S150E, 200E, 400E - I/O, L23P 2 E14 3 J13 - - XC2S150E, 200E, 400E - I/O (TRDY) I/O, L22N 2 D15 XC2S50E, 150E, 200E, 300E, 400E - I/O, VREF Bank 2, L22P 2 C16 XC2S50E, 150E, 200E, 300E, 400E All I/O, L21N 2 G12 XC2S50E, 100E, 200E, 300E - I/O, L21P 2 F12 XC2S50E, 100E, 200E, 300E - I/O, L20N 2 E13 XC2S100E, 200E, 300E - I/O (IRDY), L30N_YY 2 H16 All - I/O, L30P_YY 2 G16 All - I/O, L29N 2 H14 XC2S100E, 150E, 200E, 400E XC2S400E XC2S100E, 150E, 200E, 400E - XC2S50E, 300E, 400E - I/O, L29P I/O (D3), L28N 2 2 H15 G15 DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com 69 R Spartan-IIE FPGA Family: Pinout Tables FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) Pad Name LVDS Async. Output Option Pad Name VREF Option Bank Pin I/O, L20P 2 D14 XC2S100E, 200E, 300E XC2S200E, 300E, 400E I/O (DIN, D0), L19N_YY 2 B16 All - I/O (DOUT, BUSY), L19P_YY 2 CCLK 2 A15 - - TDO 2 B14 - - TDI - C13 - - I/O (CS), L18P_YY 1 A14 All - I/O (WRITE), L18N_YY 1 A13 I/O, L17P 1 B13 XC2S50E, XC2S200E, 100E, 200E, 300E, 400E 300E, 400E I/O, L17N 1 C12 XC2S50E, 100E, 200E, 300E, 400E - I/O, L16P_YY 1 B12 All - I/O, L16N_YY 1 A12 All - I/O, VREF Bank 1, L15P_YY 1 D12 All All I/O, L15N_YY 1 E11 All - I/O, L14P 1 D11 XC2S50E, 100E, 150E, 300E - - Function C15 All All - 1 C11 XC2S50E, 100E, 150E, 300E I/O, L13P 1 B11 XC2S50E, XC2S100E, 100E, 200E, 150E, 200E, 300E, 400E 300E, 400E I/O, L13N 1 A11 XC2S50E, 100E, 200E, 300E, 400E LVDS Async. Output Option VREF Option Bank Pin I/O, L12P 1 E10 XC2S50E, 100E, 200E, 300E, 400E - I/O, L12N 1 D10 XC2S50E, 100E, 200E, 300E, 400E - I/O 1 C10 - - I/O, L11P 1 B10 XC2S50E, 200E, 300E, 400E - I/O, L11N 1 A10 XC2S50E, 200E, 300E, 400E - I/O, VREF Bank 1, L10P 1 D9 XC2S50E, 200E, 300E, 400E All I/O, L10N 1 C9 XC2S50E, 200E, 300E, 400E - I/O, L9P 1 B9 XC2S50E, 150E, 200E, 400E - I/O, L9N 1 A9 XC2S50E, 150E, 200E, 400E XC2S400E I/O (DLL), L8P 1 A8 - - GCK2, I 1 B8 - - GCK3, I 0 C8 - - I/O (DLL), L8N 0 D8 - - I/O 0 A7 - XC2S400E I/O, L7P 0 E7 XC2S50E, 200E, 300E, 400E - I/O, VREF Bank 0, L7N 0 D7 XC2S50E, 200E, 300E, 400E All Function - I/O, L14N 70 FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) - www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FT256 Pinouts (XC2S50E, XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E) (Continued) Pad Name Function I/O, L6P I/O, L6N Bank Pin 0 C7 0 B7 LVDS Async. Output Option Pin Name Pin Name VREF Option GCK0 4 T9 GCK0, I R9 I/O (DLL), L52P XC2S50E, 200E, 300E, 400E - GCK1 5 T8 GCK1, I R8 I/O (DLL), L52N GCK2 1 B8 GCK2, I A8 XC2S50E, 200E, 300E, 400E - I/O (DLL), L8P GCK3 0 C8 GCK3, I D8 I/O (DLL), L8N A6 - - I/O, L5P 0 B6 XC2S50E, 100E, 200E, 300E, 400E - XC2S50E, 100E, 200E, 300E, 400E - XC2S50E, 100E, 200E, 300E, 400E - I/O, L4P I/O, L4N 0 0 C6 A5 B5 N Bank 0 0 P Clock I/O I/O, L5N FT256 Differential Clock Pins Additional FT256 Package Pins VCCINT Pins C3 C14 D4 D13 E5 E12 M5 M12 N4 N13 P3 P14 - - - F8 - - F10 - - H12 - - K11 - - M9 - - VCCO Bank 0 Pins E8 XC2S50E, XC2S100E, 100E, 200E, 150E, 200E, 300E, 400E 300E, 400E I/O, L3P 0 D6 XC2S50E, 100E, 300E - I/O, L3N 0 E6 XC2S50E, 100E, 300E - I/O, L2P_YY 0 D5 All - I/O, VREF Bank 0, L2N_YY 0 C5 All All I/O, L1P_YY 0 B4 All - I/O, L1N_YY 0 C4 All - I/O, L0P_YY 0 A4 All - I/O, L0N_YY 0 A3 All XC2S200E, 300E, 400E I/O 0 B3 - - TCK - A2 - - F7 VCCO Bank 1 Pins E9 F9 VCCO Bank 2 Pins G11 H11 VCCO Bank 3 Pins J11 J12 VCCO Bank 4 Pins L9 L10 Notes: 1. Although designated with the _YY suffix in the XC2S50E, XC2S100E, XC2S150E, XC2S200E, and XC2S300E, these differential pairs are not asynchronous in the XC2S400E. 2. There is no pair L37. DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com 71 R Spartan-IIE FPGA Family: Pinout Tables Additional FT256 Package Pins (Continued) VCCO Bank 5 Pins L7 L8 M8 - - K6 - - H5 H6 - - A1 A16 B2 B15 F6 F11 G7 G8 G9 G10 H7 H8 H9 H10 J7 J8 J9 J10 K7 K8 K9 K10 L6 L11 R2 T1 T16 - - VCCO Bank 6 Pins J5 J6 VCCO Bank 7 Pins G6 GND Pins R15 72 www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E TMS - E4 - - TMS TMS TMS TMS TMS TMS I/O 7 D3 XC2S150E - I/O I/O, L113P_Y I/O I/O I/O I/O I/O 7 C2 - - - - - I/O I/O I/O I/O 7 C1 XC2S150E - - I/O, L113N_Y I/O I/O I/O I/O I/O, L#P_Y 7 D2 XC2S150E, 200E, 300E, 400E - - I/O, L112P_Y I/O, L119P_Y I/O, L119P_Y I/O, L119P_Y I/O, L119P I/O, L#N_Y 7 D1 XC2S150E, 200E, 300E, 400E - I/O I/O, L112N_Y I/O, L119N_Y I/O, L119N_Y I/O, L119N_Y I/O, L119N I/O, L#P_Y 7 E2 XC2S100E, XC2S200E, I/O, L85P_Y I/O, L111P 200E, 300E, 300E, 600E 400E, 600E I/O, VREF Bank 7, L118P_Y I/O, VREF Bank 7, L118P_Y I/O, VREF Bank 7, L118P I/O, VREF Bank 7, L118P_Y I/O, L#N_Y 7 E3 XC2S100E, 200E, 300E, 600E - I/O, L85N_Y I/O, L111N I/O, L118N_Y I/O, L118N_Y I/O, L118N I/O, L118N_Y I/O 7 E1 - - - - - I/O I/O I/O I/O 7 F5 - - - I/O I/O I/O I/O I/O I/O, L#P_Y 7 F4 XC2S100E, 200E, 300E, 600E - I/O, L117P_Y I/O, L117P_Y I/O, L117P I/O, L117P_Y I/O, L#N_Y 7 F3 XC2S100E, 200E, 300E, 600E - I/O, L84N_Y I/O, L110N I/O, L117N_Y I/O, L117N_Y I/O, L117N I/O, L117N_Y I/O, VREF Bank 7, L#P_Y 7 F2 XC2S150E, 200E, 300E, 400E, 600E All I/O, VREF Bank 7, L83P I/O, VREF Bank 7, L109P_Y I/O, VREF Bank 7, L116P_Y I/O, VREF Bank 7, L116P_Y I/O, VREF Bank 7, L116P_Y I/O, VREF Bank 7, L116P_Y I/O, L#N_Y 7 F1 XC2S150E, 200E, 300E, 400E, 600E - I/O, L83N I/O, L109N_Y I/O, L116N_Y I/O, L116N_Y I/O, L116N_Y I/O, L116N_Y I/O 7 G5 - - - I/O I/O I/O I/O I/O I/O, L#P_Y 7 G4 XC2S150E, 200E, 300E, 400E - - I/O, L108P_Y I/O, L115P_Y I/O, L115P_Y I/O, L115P_Y I/O, L115P I/O, L#N_Y 7 G3 XC2S150E, 200E, 300E, 400E - I/O I/O, L108N_Y I/O, L115N_Y I/O, L115N_Y I/O, L115N_Y I/O, L115N I/O, L#P_Y 7 G2 XC2S100E, 150E, 300E, 600E I/O, L107P_Y I/O, L114P I/O, L114P_Y I/O, L114P I/O, VREF Bank 7, L114P_Y I/O, L#N_Y 7 G1 XC2S100E, 150E, 300E, 600E I/O, L107N_Y I/O, L114N I/O, L114N_Y I/O, L114N I/O, L114N_Y DS077-4 (2.3) June 18, 2008 Product Specification I/O, L84P_Y I/O, L110P XC2S600E I/O, L82P_Y - I/O, L82N_Y www.xilinx.com 73 R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O 7 H5 - - - - - I/O I/O I/O I/O, VREF Bank 7, L#P_Y 7 H3 XC2S300E, 400E, 600E All I/O, VREF Bank 7, L81P I/O, VREF Bank 7, L106P I/O, VREF Bank 7, L113P I/O, VREF Bank 7, L113P_Y I/O, VREF Bank 7, L113P_Y I/O, VREF Bank 7, L113P_Y I/O, L#N_Y 7 H4 XC2S300E, 400E, 600E - I/O, L81N I/O, L106N I/O, L113N I/O, L113N_Y I/O, L113N_Y I/O, L113N_Y I/O, L#P_YY 7 H2 All - I/O, L80P_YY I/O, L105P_YY I/O, L112P_YY I/O, L112P_YY I/O, L112P_YY I/O, L112P_YY I/O, L#N_YY 7 H1 All - I/O, L80N_YY I/O, L105N_YY I/O, L112N_YY I/O, L112N_YY I/O, L112N_YY I/O, L112N_YY I/O 7 J6 - - - - I/O I/O I/O I/O I/O, L#P_Y 7 J4 XC2S150E, 200E, 300E, 400E - - I/O, L104P_Y I/O, L111P_Y I/O, L111P_Y I/O, L111P_Y I/O, L111P I/O, L#N_Y 7 J5 XC2S100E, 150E, 200E, 300E, 400E - I/O, L79P_Y I/O, L104N_Y I/O, L111N_Y I/O, L111N_Y I/O, L111N_Y I/O, L111N I/O, L#P_Y 7 J3 XC2S100E, 150E, 200E, 300E, 600E - I/O, L79N_Y I/O, L103P_Y I/O, L110P_Y I/O, L110P_Y I/O, L110P I/O, L110P_Y I/O, L#N_Y 7 J2 XC2S150E, 200E, 300E, 600E - - I/O, L103N_Y I/O, L110N_Y I/O, L110N_Y I/O, L110N I/O, L110N_Y I/O 7 J1 - - - - I/O I/O I/O I/O I/O, L#P 7 K5 XC2S100E, 150E, 200E, 300E, 600E(1) - I/O, L78P_YY I/O, L102P_YY I/O, L109P_YY I/O, L109P_YY I/O, L109P I/O, L109P_Y I/O, L#N 7 K6 XC2S100E, 150E, 200E, 300E, 600E(1) - I/O, L78N_YY I/O, L102N_YY I/O, L109N_YY I/O, L109N_YY I/O, L109N I/O, L109N_Y I/O, VREF Bank 7, L#P_Y 7 K3 XC2S300E, 400E, 600E All I/O, VREF Bank 7, L77P I/O, VREF Bank 7, L101P I/O, VREF Bank 7, L108P I/O, VREF Bank 7, L108P_Y I/O, VREF Bank 7, L108P_Y I/O, VREF Bank 7, L108P_Y I/O, L#N_Y 7 K4 XC2S300E, 400E, 600E - I/O, L77N I/O, L101N I/O, L108N I/O, L108N_Y I/O, L108N_Y I/O, L108N_Y I/O 7 K2 - - - - - I/O I/O I/O I/O, L#P_Y 7 K1 XC2S300E, 400E - - - I/O, L107P I/O, L107P_Y I/O, L107P_Y I/O, L107P I/O, L#N_Y 7 L1 XC2S100E, 150E, 300E, 400E - I/O, L76P_Y I/O, L100P_Y I/O, L107N I/O, L107N_Y I/O, L107N_Y I/O, L107N I/O, L#P_Y 7 L3 XC2S100E, 150E, 200E, 300E, 600E XC2S400E, 600E I/O, L76N_Y I/O, L100N_Y I/O, L106P_Y I/O, L106P_Y I/O, VREF Bank 7, L106P I/O, VREF Bank 7, L106P_Y I/O, L#N_Y 7 L2 XC2S200E, 300E, 600E - - I/O I/O, L106N_Y I/O, L106N_Y I/O, L106N I/O, L106N_Y I/O 7 L4 - - - - - I/O I/O I/O 74 www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O, L#P_YY 7 L5 All - I/O, L75P_YY I/O, L99P_YY I/O, L105P_YY I/O, L105P_YY I/O, L105P_YY I/O, L105P_YY I/O (IRDY), L#N_YY 7 L6 All - I/O (IRDY), L75N_YY I/O (IRDY), L99N_YY I/O (IRDY), L105N_YY I/O (IRDY), L105N_YY I/O (IRDY), L105N_YY I/O (IRDY), L105N_YY I/O (TRDY) 6 M1 - - I/O (TRDY) I/O (TRDY) I/O (TRDY) I/O (TRDY) I/O (TRDY) I/O (TRDY) I/O 6 M2 - - - - - I/O I/O I/O I/O, L#P_Y 6 M3 XC2S200E, 300E, 600E - - I/O I/O, L104P_Y I/O, L104P_Y I/O, L104P I/O, L104P_Y I/O, L#N_Y 6 M4 XC2S100E, 150E, 200E, 300E, 600E I/O, L104N_Y I/O, L104N_Y I/O, VREF Bank 6, L104N I/O, VREF Bank 6, L104N_Y I/O, L#P_Y 6 M5 XC2S100E, 150E, 300E, 400E - I/O, L74N_Y I/O, L98N_Y I/O, L103P I/O, L103P_Y I/O, L103P_Y I/O, L103P I/O, L#N_Y 6 M6 XC2S300E, 400E - - - I/O, L103N I/O, L103N_Y I/O, L103N_Y I/O, L103N I/O 6 N1 - - - - - I/O I/O I/O I/O 6 N2 - - I/O, L73P I/O, L97P I/O I/O I/O I/O I/O, VREF Bank 6, L#P 6 N3 XC2S200E, 400E All I/O, VREF Bank 6, L73N I/O, VREF Bank 6, L97N I/O, VREF Bank 6, L102P_Y I/O, VREF Bank 6, L102P I/O, VREF Bank 6, L102P_Y I/O, VREF Bank 6, L102P I/O, L#N 6 N4 XC2S100E, 150E, 200E, 400E - I/O, L102N_Y I/O, L102N I/O, L102N_Y I/O, L102N I/O, L#P_Y 6 N5 XC2S100E, 150E, 300E, 600E - I/O, L72N_Y I/O, L96N_Y I/O, L101P I/O, L101P_Y I/O, L101P I/O, L101P_Y I/O, L#N_Y 6 N6 XC2S300E, 600E - - - I/O, L101N I/O, L101N_Y I/O, L101N I/O, L101N_Y I/O, L#P_Y 6 P1 XC2S150E, 200E, 300E, 600E - - I/O, L95P_Y I/O, L100P_Y I/O, L100P_Y I/O, L100P I/O, L100P_Y I/O, L#N_Y 6 P2 XC2S100E, 150E, 200E, 300E, 600E - I/O, L71P_Y I/O, L95N_Y I/O, L100N_Y I/O, L100N_Y I/O, L100N I/O, L100N_Y I/O 6 R1 XC2S100E, 150E - I/O, L71N_Y I/O, L94P_Y I/O I/O I/O I/O I/O, L#P_Y 6 P3 XC2S150E, 200E, 300E, 400E, 600E - - I/O, L94N_Y I/O, L#N_Y 6 P4 XC2S200E, 300E, 400E, 600E - - - I/O, L99N_Y I/O, L99N_Y I/O, L99N_Y I/O, L99N_Y I/O, L#P_YY 6 P5 All - I/O, L70P_YY I/O, L93P_YY I/O, L98P_YY I/O, L98P_YY I/O, L98P_YY I/O, L98P_YY I/O, L#N_YY 6 P6 All - I/O, L70N_YY I/O, L93N_YY I/O, L98N_YY I/O, L98N_YY I/O, L98N_YY I/O, L98N_YY DS077-4 (2.3) June 18, 2008 Product Specification XC2S400E, I/O, L74P_Y I/O, L98P_Y 600E I/O, L72P_Y I/O, L96P_Y www.xilinx.com I/O, L99P_Y I/O, L99P_Y I/O, L99P_Y I/O, L99P_Y 75 R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O, L#P_Y 6 R2 XC2S300E, 400E, 600E - I/O, L69P I/O, L92P I/O, L97P I/O, VREF Bank 6, L#N_Y 6 R3 XC2S300E, 400E, 600E All I/O, VREF Bank 6, L69N I/O, VREF Bank 6, L92N I/O, VREF Bank 6, L97N I/O, VREF Bank 6, L97N_Y I/O, VREF Bank 6, L97N_Y I/O, VREF Bank 6, L97N_Y I/O 6 R4 - - - - - I/O I/O I/O I/O 6 R5 - - I/O I/O I/O I/O I/O I/O I/O, L#P 6 T2 XC2S200E, 400E, 600E XC2S600E I/O, L68P I/O, L91P I/O, L96P_Y I/O, L96P I/O, L96P_Y I/O, VREF Bank 6, L96P_Y I/O, L#N 6 T3 XC2S200E, 400E, 600E - I/O, L68N I/O, L91N I/O, L96N_Y I/O, L96N I/O, L96N_Y I/O, L96N_Y I/O, L#P_Y 6 T4 XC2S150E, 300E, 400E - - I/O, L90P_Y I/O, L95P I/O, L#N_Y 6 T5 XC2S150E, 300E, 400E - - I/O, L90N_Y I/O, L95N I/O, L#P_Y 6 T1 XC2S150E, 200E, 300E, 400E, 600E - I/O, L67P I/O, VREF Bank 6, L#N_Y 6 U1 XC2S150E, 200E, 300E, 400E, 600E All I/O, VREF Bank 6, L67N I/O, VREF Bank 6, L89N_Y I/O, VREF Bank 6, L94N_Y I/O, VREF Bank 6, L94N_Y I/O, VREF Bank 6, L94N_Y I/O, VREF Bank 6, L94N_Y I/O 6 U2 XC2S100E - I/O, L66P_Y I/O I/O I/O I/O I/O I/O, L#P_Y 6 U3 XC2S100E, 150E, 200E, 300E, 400E, 600E - I/O, L66N_Y I/O, L#N_Y 6 U4 XC2S150E, 200E, 300E, 400E, 600E - - I/O 6 V1 - - - - I/O, L#P_Y 6 W1 XC2S100E, 200E, 300E, 600E - I/O, L65P_Y I/O, L87P I/O, L#N_Y 6 V2 XC2S100E, XC2S200E, 200E, 300E, 300E, 600E 400E, 600E I/O, L65N_Y I/O, L87N I/O, VREF Bank 6, L92N_Y I/O 6 W2 - - I/O I/O I/O I/O, L#P_Y 6 V3 XC2S200E, 300E, 400E - - I/O, L86P I/O, L#N_Y 6 V4 XC2S200E, 300E, 400E - - I/O, L86N I/O 6 Y1 - - - - - I/O I/O I/O I/O, L#P_YY 6 Y2 All - I/O, L64P_YY I/O, L85P_YY I/O, L90P_YY I/O, L90P_YY I/O, L90P_YY I/O, L90P_YY I/O, L#N_YY 6 W3 All - I/O, L64N_YY I/O, L85N_YY I/O, L90N_YY I/O, L90N_YY I/O, L90N_YY I/O, L90N_YY M1 - U5 - - M1 M1 M1 M1 M1 M1 76 I/O, L97P_Y I/O, L97P_Y I/O, L97P_Y I/O, L95P_Y I/O, L95P_Y I/O, L95N_Y I/O, L95N_Y I/O, L95P I/O, L95N I/O, L89P_Y I/O, L94P_Y I/O, L94P_Y I/O, L94P_Y I/O, L94P_Y I/O, L88P_Y I/O, L93P_Y I/O, L93P_Y I/O, L93P_Y I/O, L93P_Y I/O, L88N_Y www.xilinx.com I/O, L93N_Y I/O, L93N_Y - I/O I/O, L93N_Y I/O I/O I/O, L92P I/O, L92P_Y I/O, VREF Bank 6, L92N_Y I/O, VREF Bank 6, L92N I/O, VREF Bank 6, L92N_Y I/O I/O I/O I/O, L92P_Y I/O, L92P_Y I/O, L91P_Y I/O, L91P_Y I/O, L91P_Y I/O, L91N_Y I/O, L93N_Y I/O, L91N_Y I/O, L91N_Y I/O, L91P I/O, L91N DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E M0 - AA1 - - M0 M0 M0 M0 M0 M0 M2 - AB2 - - M2 M2 M2 M2 M2 M2 I/O, L#N_Y 5 AA3 XC2S150E, 200E, 300E, 400E, 600E - - I/O, L84N_Y I/O, L89N_Y I/O, L89N_Y I/O, L89N_Y I/O, L89N_Y I/O, L#P_Y 5 AB3 XC2S150E, 200E, 300E, 400E, 600E - - I/O 5 AB4 - - - - - I/O I/O I/O I/O 5 AA5 XC2S100E, 150E - I/O, L63N_Y I/O, L83N_Y I/O I/O I/O I/O I/O, L#N_Y 5 W5 XC2S100E, 150E, 200E, 300E, 400E, 600E - I/O, L88N_Y I/O, L88N_Y I/O, L88N_Y I/O, L88N_Y I/O, L#P_Y 5 Y5 XC2S200E, 300E, 400E, 600E - I/O, L#N_Y 5 AB5 XC2S100E, XC2S200E, 200E, 300E, 300E, 400E, 600E 400E, 600E I/O, L#P_Y 5 AB6 XC2S100E, 200E, 300E, 400E, 600E I/O 5 Y6 I/O 5 I/O, L#N_YY 5 I/O, L#P_YY I/O, L84P_Y I/O, L89P_Y I/O, L89P_Y I/O, L89P_Y I/O, L89P_Y I/O, L63P_Y I/O, L83P_Y I/O I/O I/O, L62N_Y I/O, L82N - I/O, L62P_Y I/O, L82P - - - - AA6 - - - I/O I/O I/O I/O I/O V6 All - I/O, L61N_YY I/O, L81N_YY I/O, L86N_YY I/O, L86N_YY I/O, L86N_YY I/O, L86N_YY 5 W6 All - I/O, L61P_YY I/O, L81P_YY I/O, L86P_YY I/O, L86P_YY I/O, L86P_YY I/O, L86P_YY I/O, VREF Bank 5, L#N_YY 5 AB7 All All I/O, VREF Bank 5, L60N_YY I/O, VREF Bank 5, L80N_YY I/O, VREF Bank 5, L85N_YY I/O, VREF Bank 5, L85N_YY I/O, VREF Bank 5, L85N_YY I/O, VREF Bank 5, L85N_YY I/O, L#P_YY 5 AA7 All - I/O, L60P_YY I/O, L80P_YY I/O, L85P_YY I/O, L85P_YY I/O, L85P_YY I/O, L85P_YY I/O 5 Y7 - - - I/O I/O I/O I/O I/O I/O, L#N_Y 5 V7 XC2S300E, 600E - - I/O, L79N I/O, L84N I/O, L84N_Y I/O, L84N I/O, L84N_Y I/O, L#P_Y 5 W7 XC2S300E, 600E - I/O I/O, L79P I/O, L84P I/O, L84P_Y I/O, L84P I/O, L84P_Y I/O, L#N_Y 5 AB8 XC2S100E, 300E, 600E XC2S600E I/O, L59N_Y I/O, L78N I/O, L83N I/O, L83N_Y I/O, L83N I/O, VREF Bank 5, L83N_Y I/O, L#P_Y 5 AA8 XC2S100E, 300E, 600E - I/O, L59P_Y I/O, L78P I/O, L83P I/O, L83P_Y I/O, L83P I/O, L83P_Y I/O 5 Y8 - - - - - I/O I/O I/O DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com I/O, L88P_Y I/O, L88P_Y I/O, L88P_Y I/O, L88P_Y I/O, VREF Bank 5, L87N_Y I/O, VREF Bank 5, L87N_Y I/O, VREF Bank 5, L87N_Y I/O, VREF Bank 5, L87N_Y I/O, L87P_Y I/O, L87P_Y I/O, L87P_Y I/O, L87P_Y - I/O I/O I/O 77 R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O, VREF Bank 5, L82N_Y I/O, VREF Bank 5, L82N_Y I/O, VREF Bank 5, L82N_Y I/O, VREF Bank 5, L82N_Y I/O, VREF Bank 5, L#N_Y 5 V8 XC2S100E, 200E, 300E, 400E, 600E All I/O, VREF Bank 5, L58N_Y I/O, VREF Bank 5, L77N I/O, L#P_Y 5 W8 XC2S100E, 200E, 300E, 400E, 600E - I/O, L58P_Y I/O, L77P I/O, L#N_Y 5 AB9 XC2S100E, 200E, 300E, 400E, 600E - I/O, L57N_Y I/O, L76N I/O, L#P_Y 5 AA9 XC2S100E, 200E, 300E, 400E, 600E - I/O, L57P_Y I/O, L76P I/O 5 AB10 - - - - I/O I/O I/O I/O I/O, L#N_Y 5 W9 XC2S150E, 300E, 400E, 600E - - I/O, L75N_Y I/O, L80N I/O, L80N_Y I/O, L80N_Y I/O, L80N_Y I/O, L#P_Y 5 Y9 XC2S100E, 150E, 300E, 400E, 600E - I/O, L56N_Y I/O, L75P_Y I/O, L80P I/O, L#N_Y 5 V9 XC2S100E, 150E, 300E, 400E, 600E - I/O, L56P_Y I/O, L74N_Y I/O, L79N I/O, L#P_Y 5 U9 XC2S150E, 300E, 400E, 600E - - I/O, L74P_Y I/O, L79P I/O 5 AA10 - - - - I/O I/O I/O I/O I/O, L#N_Y 5 W10 XC2S200E, 300E, 400E, 600E - I/O, L55N I/O, L73N I/O, L78N_Y I/O, L78N_Y I/O, L78N_Y I/O, L78N_Y I/O, L#P_Y 5 Y10 XC2S200E, 300E, 400E, 600E - I/O, L55P I/O, L73P I/O, VREF Bank 5, L#N_Y 5 V10 XC2S200E, 300E, 400E, 600E All I/O, VREF Bank 5, L54N I/O, VREF Bank 5, L72N I/O, L#P_Y 5 U10 XC2S200E, 300E, 400E, 600E - I/O, L54P I/O, L72P I/O 5 U11 - - - - - I/O I/O I/O I/O 5 V11 - - - - I/O I/O I/O I/O I/O, L#N 5 W11 XC2S200E, 400E - I/O I/O, L71N I/O, L76N_Y I/O, L76N I/O, L76N_Y I/O, L76N I/O, L#P 5 Y11 XC2S200E, 400E XC2S400E, 600E - I/O, L71P I/O, L76P_Y I/O, L76P I/O, VREF Bank 5, L76P_Y I/O, VREF Bank 5, L76P I/O 5 AA11 - - - - - I/O I/O I/O I/O (DLL), L#N 5 AB11 - - I/O (DLL), L53N I/O (DLL), L70N I/O (DLL), L75N I/O (DLL), L75N I/O (DLL), L75N I/O (DLL), L75N GCK1, I 5 AB12 - - GCK1, I GCK1, I GCK1, I GCK1, I GCK1, I GCK1, I 78 www.xilinx.com I/O, L82P_Y I/O, L82P_Y I/O, L82P_Y I/O, L82P_Y I/O, L81N_Y I/O, L81N_Y I/O, L81N_Y I/O, L81N_Y I/O, L81P_Y I/O, L81P_Y I/O, L81P_Y I/O, L81P_Y I/O, L80P_Y I/O, L80P_Y I/O, L80P_Y I/O, L79N_Y I/O, L79N_Y I/O, L79N_Y I/O, L79P_Y I/O, L79P_Y I/O, L79P_Y I/O, L78P_Y I/O, L78P_Y I/O, L78P_Y I/O, L78P_Y I/O, VREF Bank 5, L77N_Y I/O, VREF Bank 5, L77N_Y I/O, VREF Bank 5, L77N_Y I/O, VREF Bank 5, L77N_Y I/O, L77P_Y I/O, L77P_Y I/O, L77P_Y I/O, L77P_Y DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E GCK0, I 4 AA12 - - GCK0, I GCK0, I GCK0, I GCK0, I GCK0, I GCK0, I I/O (DLL), L#P 4 Y12 - - I/O (DLL), L53P I/O (DLL), L70P I/O (DLL), L75P I/O (DLL), L75P I/O (DLL), L75P I/O (DLL), L75P I/O 4 W12 - - - - - I/O I/O I/O I/O, L#N 4 V12 XC2S150E, 300E, 600E - - I/O, L69N_Y I/O, L74N I/O, L74N_Y I/O, L74N I/O, L74N_Y I/O, L#P 4 U12 XC2S150E, 300E, 600E XC2S400E, 600E I/O, L52N I/O, L69P_Y I/O, L74P I/O, L74P_Y I/O, VREF Bank 4, L74P I/O, VREF Bank 4, L74P_Y I/O, L#N 4 AB13 XC2S300E, 600E - I/O, L52P I/O I/O, L73N I/O, L73N_Y I/O, L73N I/O, L73N_Y I/O, L#P 4 AA13 XC2S300E, 600E - - - I/O, L73P I/O, L73P_Y I/O, L73P I/O, L73P_Y I/O 4 Y13 - - - - - I/O I/O I/O I/O, L#N 4 W13 XC2S200E, 300E, 400E, 600E - I/O, L51N I/O, L68N I/O, L72N_Y I/O, L72N_Y I/O, L72N_Y I/O, L72N_Y I/O, VREF Bank 4, L#P 4 V13 XC2S200E, 300E, 400E, 600E All I/O, VREF Bank 4, L51P I/O, VREF Bank 4, L68P I/O, VREF Bank 4, L72P_Y I/O, VREF Bank 4, L72P_Y I/O, VREF Bank 4, L72P_Y I/O, VREF Bank 4, L72P_Y I/O 4 U13 - - I/O, L50N I/O, L67N I/O I/O I/O I/O I/O, L#N 4 AB14 - - I/O, L50P I/O, L67P I/O, L71N I/O, L71N I/O, L71N I/O, L71N I/O, L#P 4 AA14 - - - - I/O, L71P I/O, L71P I/O, L71P I/O, L71P I/O 4 AB15 - - - - I/O I/O I/O I/O I/O, L#N 4 Y14 XC2S100E, 150E, 200E - I/O, L49N_Y I/O, L66N_Y I/O, L70N_Y I/O, L70N I/O, L70N I/O, L70N I/O, L#P 4 W14 XC2S100E, 150E, 200E - I/O, L70P I/O, L70P I/O, L70P I/O, L#N 4 U14 XC2S150E, 200E - - I/O, L69N I/O, L69N I/O, L69N I/O, L#P 4 V14 XC2S150E, 200E - - I/O, L69P I/O, L69P I/O, L69P I/O, L#N 4 AA15 XC2S100E, 200E, 300E, 400E, 600E - I/O, L48N_Y I/O, L64N I/O, L68N_Y I/O, L68N_Y I/O, L68N_Y I/O, L#P 4 Y15 XC2S100E, 200E, 300E, 400E, 600E - I/O, L48P_Y I/O, L64P I/O, L#N 4 W15 XC2S100E, 200E, 300E, 400E, 600E - I/O, L47N_Y I/O, L63N I/O, L67N_Y I/O, L67N_Y I/O, L67N_Y I/O, L67N_Y I/O, VREF Bank 4, L#P 4 V15 XC2S100E, 200E, 300E, 400E, 600E All I/O, VREF Bank 4, L47P_Y I/O, VREF Bank 4, L63P I/O, VREF Bank 4, L67P_Y I/O, VREF Bank 4, L67P_Y I/O, VREF Bank 4, L67P_Y I/O, VREF Bank 4, L67P_Y I/O 4 AB16 - - - - - I/O I/O I/O I/O 4 AB17 - - I/O I/O I/O I/O I/O I/O DS077-4 (2.3) June 18, 2008 Product Specification I/O, L49P_Y I/O, L66P_Y I/O, L70P_Y I/O, L65N_Y I/O, L69N_Y I/O, L65P_Y I/O, L69P_Y www.xilinx.com I/O, L68N_Y I/O, L68P_Y I/O, L68P_Y I/O, L68P_Y I/O, L68P_Y 79 R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option AA16 XC2S150E, 200E, 400E Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E XC2S600E I/O, L46N I/O, L62N_Y I/O, L66N_Y I/O, L66N I/O, L66N_Y I/O, VREF Bank 4, L66N I/O, L66P I/O, L66P_Y I/O, L66P I/O, L65N I/O, L65N I/O, L65N I/O, L65P I/O, L65P I/O, L65P I/O, L#N 4 I/O, L#P 4 Y16 XC2S150E, 200E, 400E - I/O, L46P I/O, L#N 4 W16 XC2S150E, 200E - - I/O, L#P 4 V16 XC2S150E, 200E - - I/O, L#N_YY 4 AA17 All - I/O, L45N_YY I/O, L60N_YY I/O, L64N_YY I/O, L64N_YY I/O, L64N_YY I/O, L64N_YY I/O, VREF Bank 4, L#P_YY 4 Y17 All All I/O, VREF Bank 4, L45P_YY I/O, VREF Bank 4, L60P_YY I/O, VREF Bank 4, L64P_YY I/O, VREF Bank 4, L64P_YY I/O, VREF Bank 4, L64P_YY I/O, VREF Bank 4, L64P_YY I/O 4 AB18 XC2S100E - I/O, L44N_Y I/O I/O I/O I/O I/O I/O, L#N 4 W17 XC2S100E, 400E, 600E - I/O, L44P_Y I/O, L59N I/O, L63N I/O, L63N I/O, L63N_Y I/O, L63N_Y I/O, L#P 4 V17 XC2S400E, 600E - - I/O, L59P I/O, L63P I/O, L63P I/O 4 AA18 - - - - - I/O I/O I/O I/O, L#N 4 Y18 XC2S100E, 200E, 300E, 400E, 600E - I/O, L43N_Y I/O, L58N I/O, L62N_Y I/O, L62N_Y I/O, L62N_Y I/O, L62N_Y I/O, L#P 4 W18 XC2S100E, XC2S200E, I/O, L43P_Y 200E, 300E, 300E, 400E, 600E 400E, 600E I/O, L58P I/O, VREF Bank 4, L62P_Y I/O, VREF Bank 4, L62P_Y I/O, VREF Bank 4, L62P_Y I/O, VREF Bank 4, L62P_Y I/O 4 AB19 I/O, L#N 4 AA19 XC2S150E, 400E I/O, L#P 4 Y19 I/O 4 I/O, L#N_YY - I/O, L62P_Y I/O, L66P_Y I/O, L61N_Y I/O, L65N_Y I/O, L61P_Y I/O, L65P_Y I/O, L63P_Y I/O, L63P_Y - I/O I/O I/O I/O I/O I/O - - I/O, L57N_Y I/O, L61N I/O, L61N I/O, L61N_Y I/O, L61N XC2S150E, 400E - - I/O, L57P_Y I/O, L61P I/O, L61P I/O, L61P_Y I/O, L61P AB21 - - - - - I/O I/O I/O 4 AB20 All - I/O, L42N_YY I/O, L56N_YY I/O, L60N_YY I/O, L60N_YY I/O, L60N_YY I/O, L60N_YY I/O, L#P_YY 4 AA20 All - I/O, L42P_YY I/O, L56P_YY I/O, L60P_YY I/O, L60P_YY I/O, L60P_YY I/O, L60P_YY DONE DONE DONE DONE DONE DONE DONE 3 W20 - - PROGRAM - Y21 - - I/O (INIT), L#N_YY 3 W21 All - I/O (INIT), L41N_YY I/O (INIT), L55N_YY I/O (INIT), L59N_YY I/O (INIT), L59N_YY I/O (INIT), L59N_YY I/O (INIT), L59N_YY I/O (D7), L#P_YY 3 Y22 All - I/O (D7), L41P_YY I/O (D7), L55P_YY I/O (D7), L59P_YY I/O (D7), L59P_YY I/O (D7), L59P_YY I/O (D7), L59P_YY I/O 3 W22 - - - - - I/O I/O I/O I/O 3 V21 - - - I/O I/O I/O I/O I/O 80 PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank LVDS Async. Output Option Pin Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O, L54N_Y I/O, L58N_Y I/O, L58N_Y I/O, L58N_Y I/O, L58N I/O, L#N 3 V19 XC2S150E, 200E, 300E, 400E - - I/O, L#P 3 V20 XC2S150E, 200E, 300E, 400E - I/O I/O, L#N 3 V22 XC2S100E, XC2S200E, 200E, 300E, 300E, 600E 400E, 600E I/O, L#P 3 U22 XC2S100E, 200E, 300E, 600E I/O 3 U21 I/O 3 I/O, L#N 3 I/O, L#P I/O, L54P_Y I/O, L58P_Y I/O, L58P_Y I/O, L58P_Y I/O, L40N_Y I/O, L53N - I/O, L40P_Y I/O, L53P - - - - U20 - - - I/O I/O I/O I/O I/O U18 XC2S100E, 200E, 300E, 600E - I/O, L39N_Y I/O, L52N I/O, L56N_Y I/O, L56N_Y I/O, L56N I/O, L56N_Y 3 U19 XC2S100E, 200E, 300E, 600E - I/O, L39P_Y I/O, L52P I/O, L56P I/O, L56P_Y I/O, VREF Bank 3, L#N 3 T21 XC2S150E, 200E, 300E, 400E, 600E All I/O, VREF Bank 3, L38N I/O, VREF Bank 3, L51N_Y I/O, VREF Bank 3, L55N_Y I/O, VREF Bank 3, L55N_Y I/O, L#P 3 T22 XC2S150E, 200E, 300E, 400E, 600E - I/O, L38P I/O 3 T20 - - - I/O I/O I/O I/O I/O I/O, L#N 3 T18 XC2S150E, 200E, 300E, 400E - - I/O, L50N_Y I/O, L54N_Y I/O, L54N_Y I/O, L54N_Y I/O, L54N I/O, L#P 3 T19 XC2S150E, 200E, 300E, 400E - I/O I/O, L#N 3 R21 XC2S100E, 150E, 300E, 600E XC2S600E I/O, L37N_Y I/O, L#P 3 R22 XC2S100E, 150E, 300E, 600E - I/O 3 R20 - - - I/O, VREF Bank 3, L#N 3 R18 XC2S300E, 400E, 600E All I/O (D6), L#P 3 R19 XC2S300E, 400E, 600E I/O (D5), L#N_YY 3 P22 I/O, L#P_YY 3 P21 DS077-4 (2.3) June 18, 2008 Product Specification I/O, VREF Bank 3, L57N_Y I/O, VREF Bank 3, L57N_Y I/O, L58P I/O, L57P_Y I/O, L57P_Y - I/O I/O, L56P_Y I/O, L56P_Y I/O, VREF Bank 3, L55N_Y I/O, VREF Bank 3, L55N_Y I/O, VREF Bank 3, L57N I/O, VREF Bank 3, L57N_Y I/O, L57P I/O, L57P_Y I/O I/O I/O, L51P_Y I/O, L55P_Y I/O, L55P_Y I/O, L55P_Y I/O, L55P_Y I/O, L50P_Y I/O, L54P_Y I/O, L54P_Y I/O, L54P_Y I/O, L49N_Y I/O, L54P I/O, L53N I/O, L53N_Y I/O, L53N I/O, VREF Bank 3, L53N_Y I/O, L53P I/O, L53P_Y I/O, L53P I/O, L53P_Y - - I/O I/O I/O I/O, VREF Bank 3, L36N I/O, VREF Bank 3, L48N I/O, VREF Bank 3, L52N I/O, VREF Bank 3, L52N_Y I/O, VREF Bank 3, L52N_Y I/O, VREF Bank 3, L52N_Y - I/O (D6), L36P I/O (D6), L48P I/O (D6), L52P I/O (D6), L52P_Y I/O (D6), L52P_Y I/O (D6), L52P_Y All - I/O (D5), L35N_YY I/O (D5), L47N_YY I/O (D5), L51N_YY I/O (D5), L51N_YY I/O (D5) L51N_YY I/O (D5), L51N_YY All - I/O, L35P_YY I/O, L47P_YY I/O, L51P_YY I/O, L51P_YY I/O, L51P_YY I/O, L51P_YY I/O, L37P_Y I/O, L49P_Y www.xilinx.com 81 R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O 3 P20 - - - - I/O I/O I/O I/O I/O, L#N 3 P18 XC2S150E, 200E, 300E, 400E - - I/O, L46N_Y I/O, L50N_Y I/O, L50N_Y I/O, L50N_Y I/O, L50N I/O, L#P 3 P19 XC2S100E, 150E, 200E, 300E, 400E - I/O, L34N_Y I/O, L#N 3 N22 XC2S100E, 150E, 200E, 300E, 600E - I/O, L34P_Y I/O, L#P 3 N21 XC2S150E, 200E, 300E, 600E - - I/O 3 P17 - - - - I/O I/O I/O I/O I/O, L#N 3 N19 XC2S100E, 150E, 200E, 300E, 600E(1) - I/O, L33N_YY I/O, L44N_YY I/O, L48N_YY I/O, L48N_YY I/O, L48N I/O, L48N_Y I/O, L#P 3 N20 XC2S100E, 150E, 200E, 300E, 600E(1) - I/O, L33P_YY I/O, L44P_YY I/O, L48P_YY I/O, L48P_YY I/O, L48P I/O, L48P_Y I/O, VREF Bank 3, L#N 3 N18 XC2S300E, 400E, 600E All I/O, VREF Bank 3, L32N I/O, VREF Bank 3, L43N I/O, VREF Bank 3, L47N I/O, VREF Bank 3, L47N_Y I/O, VREF Bank 3, L47N_Y I/O, VREF Bank 3, L47N_Y I/O (D4), L#P 3 N17 XC2S300E, 400E, 600E - I/O (D4), L32P I/O (D4), L43P I/O (D4), L47P I/O (D4), L47P_Y I/O (D4), L47P_Y I/O (D4), L47P_Y I/O 3 M22 - - - - - I/O I/O I/O I/O, L#N 3 M20 XC2S300E, 400E - - - I/O, L46N I/O, L46N_Y I/O, L46N_Y I/O, L46N I/O, L#P 3 M21 XC2S100E, 150E, 300E, 400E - I/O, L31N_Y I/O, L42N_Y I/O, L46P I/O, L#N 3 M18 XC2S100E, 150E, 200E, 300E, 600E I/O, L#P 3 M19 XC2S200E, 300E, 600E - - I/O I/O 3 M17 - - - - - I/O (TRDY) 3 L22 - - I/O (TRDY) I/O (TRDY) I/O (IRDY), L#N_YY 2 L21 All - I/O (IRDY), L30N_YY I/O, L#P_YY 2 L20 All - I/O 2 L19 - I/O, L#N 2 L18 XC2S200E, 300E, 600E 82 I/O, L46P_Y I/O, L50P_Y I/O, L50P_Y I/O, L50P_Y I/O, L45N_Y I/O, L49N_Y I/O, L49N_Y I/O, L45P_Y I/O, L49P_Y I/O, L49P_Y XC2S400E, I/O, L31P_Y I/O, L42P_Y 600E I/O, L49N I/O, L49N_Y I/O, L49P I/O, L49P_Y I/O, L46P_Y I/O, L46P_Y I/O, L45N_Y I/O, L46P I/O, VREF Bank 3, L45N I/O, VREF Bank 3, L45N_Y I/O, L45P I/O, L45P_Y I/O I/O I/O I/O (TRDY) I/O (TRDY) I/O (TRDY) I/O (TRDY) I/O (IRDY), L41N_YY I/O (IRDY), L44N_YY I/O (IRDY), L44N_YY I/O (IRDY), L44N_YY I/O (IRDY), L44N_YY I/O, L30P_YY I/O, L41P_YY I/O, L44P_YY I/O, L44P_YY I/O, L44P_YY I/O, L44P_YY - - - - I/O I/O I/O - - I/O I/O, L43N_Y I/O, L43N_Y I/O, L43N I/O, L43N_Y www.xilinx.com I/O, L45N_Y I/O, L50P I/O, L45P_Y I/O, L45P_Y DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank LVDS Async. Output Option Pin Device-Specific Pinouts: XC2S VREF Option 100E 150E I/O, L29N_Y I/O, L40N_Y 200E 300E 600E I/O, VREF Bank 2, L43P I/O, VREF Bank 2, L43P_Y I/O, L42N_Y I/O, L42N I/O, L#P 2 L17 XC2S100E, 150E, 200E, 300E, 600E XC2S400E, 600E I/O, L#N 2 K22 XC2S100E, 150E, 300E, 400E - I/O, L#P 2 K21 XC2S300E, 400E - - - I/O, L42P I/O 2 K20 - - - - - I/O I/O I/O I/O (D3) 2 K19 - - I/O (D3) I/O (D3), L39N I/O (D3) I/O (D3) I/O (D3) I/O (D3) I/O, VREF Bank 2, L#N 2 K18 XC2S100E, 200E, 400E All I/O, VREF Bank 2, L28N_Y I/O, VREF Bank 2, L39P I/O, VREF Bank 2, L41N_Y I/O, VREF Bank 2, L41N I/O, VREF Bank 2, L41N_Y I/O, VREF Bank 2, L41N I/O, L#P 2 K17 XC2S100, 150E, 200E, 400E - I/O, L28P_Y I/O, L38N_Y I/O, L41P_Y I/O, L41P I/O, L41P_Y I/O, L41P I/O, L#N 2 J22 XC2S150E, 300E, 600E - I/O I/O, L38P_Y I/O, L40N I/O, L40N_Y I/O, L40N I/O, L40N_Y I/O, L#P 2 J21 XC2S300E, 600E - - - I/O, L40P I/O, L40P_Y I/O, L40P I/O, L40P_Y I/O, L#N 2 J20 XC2S150E, 200E, 300E, 600E - - I/O, L37N_Y I/O, L39N_Y I/O, L39N_Y I/O, L39N I/O, L39N_Y I/O, L#P 2 J19 XC2S100E, 150E, 200E, 300E, 600E - I/O, L27N_Y I/O, L39P I/O, L39P_Y I/O 2 H22 XC2S100E, 150E - I/O, L27P_Y I/O, L36N_Y I/O I/O I/O I/O I/O, L#N 2 J18 XC2S150E, 200E, 300E, 400E, 600E - - I/O, L36P_Y I/O, L38N_Y I/O, L38N_Y I/O, L38N_Y I/O, L38N_Y I/O, L#P 2 J17 XC2S200E, 300E, 400E, 600E - - - I/O, L#N 2 H21 XC2S150E, 200E, 300E, 400E, 600E - I/O I/O, L35N_Y I/O, L37N_Y I/O, L37N_Y I/O, L37N_Y I/O, L37N_Y I/O (D2), L#P 2 H20 XC2S150E, 200E, 300E, 400E, 600E - I/O (D2) I/O (D2), L35P_Y I/O (D2), L37P_Y I/O (D2), L37P_Y I/O (D2), L37P_Y I/O (D2), L37P_Y I/O (D1), L#N 2 H19 XC2S300E, 400E, 600E - I/O (D1), L26N I/O (D1), L34N I/O (D1), L36N I/O (D1), L36N_Y I/O (D1), L36N_Y I/O (D1), L36N_Y I/O, VREF Bank 2, L#P 2 H18 XC2S300E, 400E, 600E All I/O, VREF Bank 2, L26P I/O, VREF Bank 2, L34P I/O, VREF Bank 2, L36P I/O, VREF Bank 2, L36P_Y I/O, VREF Bank 2, L36P_Y I/O, VREF Bank 2, L36P_Y I/O 2 G22 - - - - - I/O I/O I/O I/O 2 F22 - - I/O I/O I/O I/O I/O I/O DS077-4 (2.3) June 18, 2008 Product Specification I/O, L29P_Y I/O, L40P_Y I/O, L43P_Y I/O, L43P_Y 400E I/O, L42N I/O, L42N_Y I/O, L42P_Y I/O, L42P_Y I/O, L37P_Y I/O, L39P_Y I/O, L39P_Y www.xilinx.com I/O, L42P I/O, L38P_Y I/O, L38P_Y I/O, L38P_Y I/O, L38P_Y 83 R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O, L35N_Y I/O, VREF Bank 2, L35N_Y I/O, L#N 2 G21 XC2S200E, 400E, 600E XC2S600E I/O, L25N I/O, L33N I/O, L35N_Y I/O, L35N I/O, L#P 2 G20 XC2S200E, 400E, 600E - I/O, L25P I/O, L33P I/O, L35P_Y I/O, L35P I/O, L#N 2 G19 XC2S150E, 300E - - I/O, L32N_Y I/O, L34N I/O, L34N_Y I/O, L34N I/O, L34N I/O, L#P 2 G18 XC2S150E, 300E - - I/O, L32P_Y I/O, L34P I/O, L34P_Y I/O, L34P I/O, L34P I/O, L#N 2 E22 XC2S150E, 200E, 300E, 400E, 600E - I/O, L24N I/O, L31N_Y I/O, L33N_Y I/O, L33N_Y I/O, L33N_Y I/O, L33N_Y I/O, VREF Bank 2, L#P 2 F21 XC2S150E, 200E, 300E, 400E, 600E All I/O, VREF Bank 2, L24P I/O, VREF Bank 2, L31P_Y I/O, VREF Bank 2, L33P_Y I/O, VREF Bank 2, L33P_Y I/O, VREF Bank 2, L33P_Y I/O, VREF Bank 2, L33P_Y I/O 2 E21 XC2S100E - I/O, L23N_Y I/O I/O I/O I/O I/O I/O, L#N 2 F20 XC2S100E, 150E, 200E, 300E, 400E, 600E - I/O, L23P_Y I/O, L30N_Y I/O, L32N_Y I/O, L32N_Y I/O, L32N_Y I/O, L32N_Y I/O, L#P 2 F19 XC2S150E, 200E, 300E, 400E, 600E - - I/O 2 F18 - - - - - I/O I/O I/O I/O, L#N 2 D22 XC2S100E, 200E, 300E, 600E - I/O, L22N_Y I/O, L29N I/O, L31N_Y I/O, L31N_Y I/O, L31N I/O, L31N_Y I/O, L#P 2 D21 XC2S100E, XC2S200E, I/O, L22P_Y 200E, 300E, 300E, 600E 400E, 600E I/O, L29P I/O, VREF Bank 2, L31P_Y I/O, VREF Bank 2, L31P_Y I/O, VREF Bank 2, L31P I/O, VREF Bank 2, L31P_Y I/O, L#N 2 E20 XC2S200E, 300E, 400E - I/O I/O, L28N I/O, L30N_Y I/O, L30N_Y I/O, L30N_Y I/O, L30N I/O, L#P 2 E19 XC2S200E, 300E, 400E - - I/O, L28P I/O 2 D20 - - - - - I/O I/O I/O I/O (DIN, D0), L#N_YY 2 C22 All - I/O (DIN, D0), L21N_YY I/O (DIN, D0), L27N_YY I/O (DIN, D0), L29N_YY I/O (DIN, D0), L29N_YY I/O (DIN, D0), L29N_YY I/O (DIN, D0), L29N_YY I/O (DOUT, BUSY), L#P_YY 2 C21 All - I/O (DOUT, BUSY), L21P_YY I/O (DOUT, BUSY), L27P_YY I/O (DOUT, BUSY), L29P_YY I/O (DOUT, BUSY), L29P_YY I/O (DOUT, BUSY), L29P_YY I/O (DOUT, BUSY), L29P_YY CCLK 2 B22 - - CCLK CCLK CCLK CCLK CCLK CCLK TDO 2 A21 - - TDO TDO TDO TDO TDO TDO TDI - C19 - - TDI TDI TDI TDI TDI TDI I/O (CS), L#P_YY 1 B20 All - I/O (CS), L20P_YY I/O (CS), L26P_YY I/O (CS), L28P_YY I/O (CS), L28P_YY I/O (CS), L28P_YY I/O (CS), L28P_YY 84 I/O, L35P_Y I/O, L35P_Y I/O, L30P_Y I/O, L32P_Y I/O, L32P_Y I/O, L32P_Y I/O, L32P_Y www.xilinx.com I/O, L30P_Y I/O, L30P_Y I/O, L30P_Y I/O, L30P DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O (WRITE), L#N_YY 1 A20 All - I/O (WRITE), L20N_YY I/O (WRITE), L26N_YY I/O (WRITE), L28N_YY I/O (WRITE), L28N_YY I/O (WRITE), L28N_YY I/O (WRITE), L28N_YY I/O 1 D18 - - - - - I/O I/O I/O I/O 1 C18 - - - I/O I/O I/O I/O I/O I/O, L#P 1 B19 XC2S200E, 300E, 400E, 600E - - I/O, L25P I/O, L#N 1 A19 XC2S200E, 300E, 400E, 600E - I/O I/O, L25N I/O, L27N_Y I/O, L27N_Y I/O, L27N_Y I/O, L27N_Y I/O, L#P 1 B18 XC2S100E, XC2S200E, I/O, L19P_Y 200E, 300E, 300E, 400E, 600E 400E, 600E I/O, L24P I/O, VREF Bank 1, L26P_Y I/O, VREF Bank 1, L26P_Y I/O, VREF Bank 1, L26P_Y I/O, VREF Bank 1, L26P_Y I/O, L#N 1 A18 XC2S100E, 200E, 300E, 400E, 600E - I/O, L19N_Y I/O, L24N I/O, L26N_Y I/O, L26N_Y I/O, L26N_Y I/O, L26N_Y I/O 1 D17 - - - - - I/O I/O I/O I/O 1 C17 - - - I/O I/O I/O I/O I/O I/O, L#P_YY 1 B17 All - I/O, L18P_YY I/O, L23P_YY I/O, L25P_YY I/O, L25P_YY I/O, L25P_YY I/O, L25P_YY I/O, L#N_YY 1 A17 All - I/O, L18N_YY I/O, L23N_YY I/O, L25N_YY I/O, L25N_YY I/O, L25N_YY I/O, L25N_YY I/O, VREF Bank 1, L#P_YY 1 E16 All All I/O, VREF Bank 1, L17P_YY I/O, VREF Bank 1, L22P_YY I/O, VREF Bank 1, L24P_YY I/O, VREF Bank 1, L24P_YY I/O, VREF Bank 1, L24P_YY I/O, VREF Bank 1, L24P_YY I/O, L#N_YY 1 E17 All - I/O, L17N_YY I/O, L22N_YY I/O, L24N_YY I/O, L24N_YY I/O, L24N_YY I/O, L24N_YY I/O 1 E15 - - - I/O I/O I/O I/O I/O I/O, L#P 1 D16 XC2S300E, 600E - - I/O, L21P I/O, L23P I/O, L23P_Y I/O, L23P I/O, L23P_Y I/O, L#N 1 C16 XC2S300E, 600E - I/O I/O, L21N I/O, L23N I/O, L23N_Y I/O, L23N I/O, L23N_Y I/O, L#P 1 B16 XC2S100E, 300E, 600E I/O, L20P I/O, L22P I/O, L22P_Y I/O, L22P I/O, VREF Bank 1, L22P_Y I/O, L#N 1 A16 XC2S100E, 300E, 600E - I/O, L16N_Y I/O, L20N I/O, L22N I/O, L22N_Y I/O, L22N I/O, L22N_Y I/O 1 F14 - - - - - I/O I/O I/O I/O, VREF Bank 1, L#P 1 D15 XC2S100E, 200E, 300E, 400E, 600E All I/O, VREF Bank 1, L15P_Y I/O, VREF Bank 1, L19P I/O, VREF Bank 1, L21P_Y I/O, VREF Bank 1, L21P_Y I/O, VREF Bank 1, L21P_Y I/O, VREF Bank 1, L21P_Y I/O, L#N 1 C15 XC2S100E, 200E, 300E, 400E, 600E - I/O, L15N_Y I/O, L19N I/O, L21N_Y I/O, L21N_Y I/O, L21N_Y I/O, L21N_Y I/O, L#P 1 B15 XC2S100E, 200E, 300E, 400E, 600E - I/O, L14P_Y I/O, L18P DS077-4 (2.3) June 18, 2008 Product Specification XC2S600E I/O, L16P_Y www.xilinx.com I/O, L27P_Y I/O, L27P_Y I/O, L27P_Y I/O, L27P_Y I/O, L20P_Y I/O, L20P_Y I/O, L20P_Y I/O, L20P_Y 85 R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O, L#N 1 A15 XC2S100E, 200E, 300E, 400E, 600E - I/O, L14N_Y I/O, L18N I/O, L20N_Y I/O, L20N_Y I/O, L20N_Y I/O, L20N_Y I/O 1 E14 - - - - I/O I/O I/O I/O I/O, L#P 1 D14 XC2S150E, 300E, 400E, 600E - - I/O, L17P_Y I/O, L19P I/O, L#N 1 C14 XC2S100E, 150E, 300E, 400E, 600E - I/O, L13P_Y I/O, L17N_Y I/O, L19N I/O, L#P 1 B14 XC2S100E, 150E, 300E, 400E, 600E - I/O, L13N_Y I/O, L16P_Y I/O, L18P I/O, L#N 1 A14 XC2S150E, 300E, 400E, 600E - - I/O, L16N_Y I/O, L18N I/O, L18N_Y I/O, L18N_Y I/O, L18N_Y I/O 1 E13 - - - - I/O I/O I/O I/O I/O, L#P 1 D13 XC2S200E, 300E, 400E, 600E - I/O, L12P I/O, L15P I/O, L#N 1 C13 XC2S200E, 300E, 400E, 600E - I/O, L12N I/O, L15N I/O, L17N_Y I/O, L17N_Y I/O, L17N_Y I/O, L17N_Y I/O, VREF Bank 1, L#P 1 B13 XC2S200E, 300E, 400E, 600E All I/O, VREF Bank 1, L11P I/O, VREF Bank 1, L14P I/O, VREF Bank 1, L16P_Y I/O, VREF Bank 1, L16P_Y I/O, VREF Bank 1, L16P_Y I/O, VREF Bank 1, L16P_Y I/O, L#N 1 A13 XC2S200E, 300E, 400E, 600E - I/O, L11N I/O, L14N I/O, L16N_Y I/O, L16N_Y I/O, L16N_Y I/O, L16N_Y I/O 1 F13 - - - - - I/O I/O I/O I/O, L#P 1 C12 XC2S300E, 600E - - - I/O, L15P I/O, L15P_Y I/O, L15P I/O, L15P_Y I/O, L#N 1 B12 XC2S300E, 600E - I/O, L10P I/O I/O, L15N I/O, L15N_Y I/O, L15N I/O, L15N_Y I/O, L#P 1 D12 XC2S150E, 300E, 600E XC2S400E, 600E I/O, L10N I/O, L13P_Y I/O, L14P I/O, L14P_Y I/O, VREF Bank 1, L14P I/O, VREF Bank 1, L14P_Y I/O, L#N 1 E12 XC2S150E, 300E, 600E - - I/O, L13N_Y I/O, L14N I/O, L14N_Y I/O, L14N I/O, L14N_Y I/O 1 F12 - - - - - I/O I/O I/O I/O (DLL), L#P 1 A12 - - I/O (DLL), L9P I/O (DLL), L12P I/O (DLL), L13P I/O (DLL), L13P I/O (DLL), L13P I/O (DLL), L13P GCK2, I 1 A11 - - GCK2, I GCK2, I GCK2, I GCK2, I GCK2, I GCK2, I GCK3, I 0 C11 - - GCK3, I GCK3, I GCK3, I GCK3, I GCK3, I GCK3, I I/O (DLL), L#N 0 B11 - - I/O (DLL), L9N I/O (DLL), L12N I/O (DLL), L13N I/O (DLL), L13N I/O (DLL), L13N I/O (DLL), L13N I/O 0 D11 - - - - - I/O I/O I/O 86 www.xilinx.com I/O, L19P_Y I/O, L19P_Y I/O, L19P_Y I/O, L19N_Y I/O, L19N_Y I/O, L19N_Y I/O, L18P_Y I/O, L18P_Y I/O, L18P_Y I/O, L17P_Y I/O, L17P_Y I/O, L17P_Y I/O, L17P_Y DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O 0 F11 - XC2S400E, 600E - - I/O I/O I/O, VREF Bank 0 I/O, VREF Bank 0 I/O, L#P 0 A10 XC2S300E, 600E - I/O I/O, L11P I/O, L12P I/O, L12P_Y I/O, L12P I/O, L12P_Y I/O, L#N 0 B10 XC2S300E, 600E - - I/O, L11N I/O, L12N I/O, L12N_Y I/O, L12N I/O, L12N_Y I/O 0 E11 - - - - - I/O I/O I/O I/O, L#P 0 C10 XC2S200E, 300E, 400E, 600E - I/O, L8P I/O, L10P I/O, VREF Bank 0, L#N 0 D10 XC2S200E, 300E, 400E, 600E All I/O, VREF Bank 0, L8N I/O, VREF Bank 0, L10N I/O 0 F10 - - I/O, L7P I/O I/O I/O I/O I/O I/O, L#P 0 A9 - - I/O, L7N I/O I/O, L10P I/O, L10P I/O, L10P I/O, L10P I/O, L#N 0 B9 - - - - I/O, L10N I/O, L10N I/O, L10N I/O, L10N I/O 0 E10 - - - - I/O I/O I/O I/O I/O, L#P 0 C9 XC2S100E, 150E, 200E - I/O, L6P_Y I/O, L9P_Y I/O, L9P_Y I/O, L9P I/O, L9P I/O, L9P I/O, L#N 0 D9 XC2S100E, 150E, 200E - I/O, L6N_Y I/O, L9N_Y I/O, L9N_Y I/O, L9N I/O, L9N I/O, L9N I/O, L#P 0 F9 XC2S150E, 200E - - I/O, L8P_Y I/O, L8P_Y I/O, L8P I/O, L8P I/O, L8P I/O, L#N 0 E9 XC2S150E, 200E - - I/O, L8N_Y I/O, L8N_Y I/O, L8N I/O, L8N I/O, L8N I/O, L#P 0 A8 XC2S100E, 200E, 300E, 400E, 600E - I/O, L5P_Y I/O, L7P I/O, L7P_Y I/O, L7P_Y I/O, L7P_Y I/O, L7P_Y I/O, L#N 0 B8 XC2S100E, 200E, 300E, 400E, 600E - I/O, L5N_Y I/O, L7N I/O, L7N_Y I/O, L7N_Y I/O, L7N_Y I/O, L7N_Y I/O, L#P 0 C8 XC2S100E, 200E, 300E, 400E, 600E - I/O, L4P_Y I/O, L6P I/O, L6P_Y I/O, L6P_Y I/O, L6P_Y I/O, L6P_Y I/O, VREF Bank 0, L#N 0 D8 XC2S100E, 200E, 300E, 400E, 600E All I/O, VREF Bank 0, L4N_Y I/O, VREF Bank 0, L6N I/O, VREF Bank 0, L6N_Y I/O, VREF Bank 0, L6N_Y I/O, VREF Bank 0, L6N_Y I/O, VREF Bank 0, L6N_Y I/O 0 A7 - - - - - I/O I/O I/O I/O 0 B7 - - I/O I/O I/O I/O I/O I/O I/O, L#P 0 C7 XC2S150E, 200E XC2S600E I/O, L3P I/O, L5P_Y I/O, L5P_Y I/O, L5P I/O, L5P I/O, VREF Bank 0, L5P I/O, L#N 0 D7 XC2S150E, 200E - I/O, L3N I/O, L5N_Y I/O, L5N_Y I/O, L5N I/O, L5N I/O, L5N I/O, L#P 0 E8 XC2S150E, 200E - - I/O, L4P_Y I/O, L4P_Y I/O, L4P I/O, L4P I/O, L4P I/O, L#N 0 E7 XC2S150E, 200E - - I/O, L4N_Y I/O, L4N_Y I/O, L4N I/O, L4N I/O, L4N DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com I/O, L11P_Y I/O, L11P_Y I/O, L11P_Y I/O, L11P_Y I/O, VREF Bank 0, L11N_Y I/O, VREF Bank 0, L11N_Y I/O, VREF Bank 0, L11N_Y I/O, VREF Bank 0, L11N_Y 87 R Spartan-IIE FPGA Family: Pinout Tables FG456 Pinouts (XC2S100E, XC2S150E, XC2S200E, XC2S300E, XC2S400E, XC2S600E) Pad Name Function Bank Pin LVDS Async. Output Option Device-Specific Pinouts: XC2S VREF Option 100E 150E 200E 300E 400E 600E I/O, L#P_YY 0 A6 All - I/O, L2P_YY I/O, L3P_YY I/O, L3P_YY I/O, L3P_YY I/O, L3P_YY I/O, L3P_YY I/O, VREF Bank 0, L#N_YY 0 B6 All All I/O, VREF Bank 0, L2N_YY I/O, VREF Bank 0, L3N_YY I/O, VREF Bank 0, L3N_YY I/O, VREF Bank 0, L3N_YY I/O, VREF Bank 0, L3N_YY I/O, VREF Bank 0, L3N_YY I/O 0 C6 XC2S100E - I/O, L1P_Y I/O I/O I/O I/O I/O I/O, L#P 0 A5 XC2S100E - I/O, L1N_Y I/O, L2P I/O, L2P I/O, L2P I/O, L2P I/O, L2P I/O, L#N 0 B5 - - - I/O, L2N I/O, L2N I/O, L2N I/O, L2N I/O, L2N I/O 0 D6 - - - - - I/O I/O I/O I/O, L#P 0 B4 XC2S100E, 200E, 300E, 400E, 600E - I/O, L0P_Y I/O, L1P I/O, L1P_Y I/O, L1P_Y I/O, L1P_Y I/O, L1P_Y I/O, L#N 0 C5 XC2S100E, XC2S200E, I/O, L0N_Y 200E, 300E, 300E, 400E, 600E 400E, 600E I/O, L1N I/O, VREF Bank 0, L1N_Y I/O, VREF Bank 0, L1N_Y I/O, VREF Bank 0, L1N_Y I/O, VREF Bank 0, L1N_Y I/O 0 A4 - - I/O I/O I/O I/O I/O I/O I/O, L#P 0 A3 XC2S150E, 400E, 600E - - I/O, L0P_Y I/O, L0P I/O, L0P I/O, L0P_Y I/O, L0P_Y I/O, L#N 0 B3 XC2S150E, 400E, 600E - - I/O, L0N_Y I/O, L0N I/O, L0N I/O, L0N_Y I/O, L0N_Y I/O 0 C4 - - - - - I/O I/O I/O I/O 0 D5 - - I/O I/O I/O I/O I/O I/O TCK - E6 - - TCK TCK TCK TCK TCK TCK Notes: 1. Although designated with the _YY suffix in the XC2S100E, XC2S150E, XC2S200E, and XC2S300E, these differential pairs are not asynchronous in the XC2S400E. FG456 Differential Clock Pins P N Clock Bank Pin Name Pin Name GCK0 4 AA12 GCK0, I Y12 I/O (DLL), L#P GCK1 5 AB12 GCK1, I AB11 I/O (DLL), L#N GCK2 1 A11 GCK2, I A12 I/O (DLL), L#P GCK3 0 C11 GCK3, I B11 I/O (DLL), L#N Additional FG456 Package Pins VCCINT Pins D4(1) D19(1) E5 E18 F6 F17 G7 G8 G15 G16 H7 H16 R7 R16 T7 T8 T15 T16 W19(1) - - - - - - - U6 U17 V5 V18 W4(1) F8 G9 G10 - VCCO Bank 0 Pins F7 88 www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables Additional FG456 Package Pins (Continued) VCCO Bank 1 Pins F15 F16 G13 G14 - - - - - H17 J16 K16 - - - - - P16 R17 T17 - - - - - T14 U15 U16 - - - - - T10 U7 U8 - - - - - P7 R6 T6 - - - - - H6 J7 K7 - - - - - A1 A2(2) A22 B1(2) B2 B21 C3 C20 G11 G12 J9 J10 J11 J12 J13 J14 K9 K10 K11 K12 K13 K14 L7 L9 L10 L11 L12 L13 L14 L16 M7 M9 M10 M11 M12 M13 M14 M16 N9 N10 N11 N12 N13 N14 P9 P10 P11 P12 P13 P14 T11 T12 Y20 Y3 AA2 AA4(2) AA21 AA22(2) AB1 AB22 - - D4(1) D19(1) W4(1) W19(1) Y4(2) AA4(2) AA22(2) VCCO Bank 2 Pins G17 VCCO Bank 3 Pins N16 VCCO Bank 4 Pins T13 VCCO Bank 5 Pins T9 VCCO Bank 6 Pins N7 VCCO Bank 7 Pins G6 GND Pins Y4(2) Not Connected Pins A2(2) B1(2) Notes: 1. VCCINT connections in XC2S400E and XC2S600E. No Connects (no internal connection) in XC2S100E, XC2S150E, XC2S200E, and XC2S300E. 2. GND connections in XC2S400E and XC2S600E. No Connects (no internal connection) in XC2S100E, XC2S150E, XC2S200E, and XC2S300E FG676 Pinouts (XC2S400E, XC2S600E) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option TMS - B1 - - TMS TMS I/O 7 D3 - - I/O I/O I/O, L204P 7 C2 - - - I/O, L204P I/O, L204N 7 C1 - - - I/O, L204N I/O, L203P 7 D2 XC2S600E - - I/O, L203P_Y I/O, L203N 7 D1 XC2S600E - I/O I/O, L203N_Y I/O, L202P_YY 7 E2 All - I/O, L202P_YY I/O, L202P_YY I/O, L202N_YY 7 E1 All - I/O, L202N_YY I/O, L202N_YY Function DS077-4 (2.3) June 18, 2008 Product Specification VREF Option XC2S400E XC2S600E www.xilinx.com 89 R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L201P 7 E4 XC2S400E - I/O, L201P_Y I/O, L201P I/O, L201N 7 F5 XC2S400E - I/O, L201N_Y I/O, L201N I/O, VREF Bank 7, L200P 7 F4 XC2S600E All I/O, VREF Bank 7, L200P I/O, VREF Bank 7, L200P_Y I/O, L200N 7 F3 XC2S600E - I/O, L200N I/O, L200N_Y I/O, L199P 7 F2 XC2S600E - - I/O, L199P_Y I/O, L199N 7 F1 XC2S600E - I/O I/O, L199N_Y I/O, L198P 7 G6 XC2S400E - I/O, L198P_Y I/O, L198P I/O, L198N 7 G5 XC2S400E - I/O, L198N_Y I/O, L198N I/O, L197P 7 G4 XC2S600E - I/O, L197P I/O, L197P_Y I/O, L197N 7 G3 XC2S600E - I/O, L197N I/O, L197N_Y I/O, VREF Bank 7, L196P_YY 7 G2 All All I/O, VREF Bank 7, L196P_YY I/O, VREF Bank 7, L196P_YY I/O, L196N_YY 7 G1 All - I/O, L196N_YY I/O, L196N_YY I/O 7 H7 - - I/O I/O I/O, L195P_YY 7 H6 All - I/O, L195P_YY I/O, L195P_YY I/O, L195N_YY 7 H5 All - I/O, L195N_YY I/O, L195N_YY I/O 7 J8 - - - I/O I/O, L194P 7 H2 XC2S400E - I/O, L194P_Y I/O, L194P I/O, L194N 7 H1 XC2S400E - I/O, L194N_Y I/O, L194N I/O, L193P 7 J7 XC2S600E XC2S600E I/O I/O, VREF Bank 7, L193P_Y I/O, L193N 7 J6 XC2S600E - - I/O, L193N_Y I/O 7 J5 - - I/O I/O I/O, L192P_YY 7 J4 All - I/O, L192P_YY I/O, L192P_YY I/O, L192N_YY 7 J3 All - I/O, L192N_YY I/O, L192N_YY I/O 7 K5 - - I/O I/O I/O, VREF Bank 7, L191P_YY 7 J2 All All I/O, VREF Bank 7, L191P_YY I/O, VREF Bank 7, L191P_YY I/O, L191N_YY 7 J1 All - I/O, L191N_YY I/O, L191N_YY I/O, L190P_YY 7 K8 All - I/O, L190P_YY I/O, L190P_YY I/O, L190N_YY 7 K7 All - I/O, L190N_YY I/O, L190N_YY I/O 7 K4 - - - I/O I/O, L189P_YY 7 K3 All - I/O, L189P_YY I/O, L189P_YY I/O, L189N_YY 7 K2 All - I/O, L189N_YY I/O, L189N_YY I/O 7 K1 - - - I/O Function 90 VREF Option XC2S400E XC2S600E www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L188P 7 L8 XC2S400E - I/O, L188P_Y I/O, L188P I/O, L188N 7 L7 XC2S400E - I/O, L188N_Y I/O, L188N I/O, L187P 7 L6 XC2S600E - I/O, L187P I/O, L187P_Y I/O, L187N 7 L5 XC2S600E - I/O, L187N I/O, L187N_Y I/O 7 L3 - - - I/O I/O, L186P 7 L2 XC2S600E - I/O, L186P I/O, L186P_Y I/O, L186N 7 L1 XC2S600E - I/O, L186N I/O, L186N_Y I/O 7 M9 - - - I/O I/O, L185P 7 M8 XC2S600E - I/O, L185P I/O, L185P_Y I/O, L185N 7 M7 XC2S600E - I/O, L185N I/O, L185N_Y I/O, VREF Bank 7, L184P_YY 7 M6 All All I/O, VREF Bank 7, L184P_YY I/O, VREF Bank 7, L184P_YY I/O, L184N_YY 7 M5 All - I/O, L184N_YY I/O, L184N_YY I/O 7 M4 - - - I/O I/O, L183P_YY 7 M2 All - I/O, L183P_YY I/O, L183P_YY I/O, L183N_YY 7 M1 All - I/O, L183N_YY I/O, L183N_YY I/O 7 N9 - - - I/O I/O, L182P 7 N8 XC2S400E - I/O, L182P_Y I/O, L182P I/O, L182N 7 N7 XC2S400E - I/O, L182N_Y I/O, L182N I/O, VREF Bank 7, L181P 7 N6 XC2S600E All I/O, VREF Bank 7, L181P I/O, VREF Bank 7, L181P_Y I/O, L181N 7 N5 XC2S600E - I/O, L181N I/O, L181N_Y I/O 7 N4 - - - I/O I/O, L180P_YY 7 N3 All - I/O, L180P_YY I/O, L180P_YY I/O, L180N_YY 7 N2 All - I/O, L180N_YY I/O, L180N_YY I/O 7 N1 - - - I/O I/O, L179P_YY 7 P1 All - I/O, L179P_YY I/O, L179P_YY I/O (IRDY), L179N_YY 7 P2 All - I/O (IRDY), L179N_YY I/O (IRDY), L179N_YY I/O (TRDY), L178P 6 P3 XC2S600E - I/O (TRDY) I/O (TRDY), L178P_Y I/O, L178N 6 P4 XC2S600E - - I/O, L178N_Y I/O, L177P 6 P5 XC2S600E - - I/O, L177P_Y I/O, L177N 6 P6 XC2S600E - I/O I/O, L177N_Y I/O 6 P7 - - I/O I/O I/O, L176P 6 P8 XC2S600E - I/O, L176P I/O, L176P_Y Function DS077-4 (2.3) June 18, 2008 Product Specification VREF Option XC2S400E XC2S600E www.xilinx.com 91 R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Bank Pin LVDS Async. Output Option I/O, VREF Bank 6, L176N 6 P9 XC2S600E I/O, L175P 6 R1 I/O, L175N 6 I/O Function VREF Option Device-Specific Pinouts XC2S400E XC2S600E All I/O, VREF Bank 6, L176N I/O, VREF Bank 6, L176N_Y XC2S400E - I/O, L175P_Y I/O, L175P R2 XC2S400E - I/O, L175N_Y I/O, L175N 6 R4 - - - I/O I/O, L174P_YY 6 R5 All - I/O, L174P_YY I/O, L174P_YY I/O, L174N_YY 6 R6 All - I/O, L174N_YY I/O, L174N_YY I/O 6 R7 - - - I/O I/O, L173P_YY 6 R8 All - I/O, L173P_YY I/O, L173P_YY I/O, VREF Bank 6, L173N_YY 6 R9 All All I/O, VREF Bank 6, L173N_YY I/O, VREF Bank 6, L173N_YY I/O, L172P 6 T1 XC2S600E - I/O, L172P I/O, L172P_Y I/O, L172N 6 T2 XC2S600E - I/O, L172N I/O, L172N_Y I/O 6 T3 - - - I/O I/O, L171P 6 T5 XC2S600E - I/O, L171P I/O, L171P_Y I/O, L171N 6 T6 XC2S600E - I/O, L171N I/O, L171N_Y I/O 6 U1 - - - I/O I/O, L170P 6 T7 XC2S600E - I/O, L170P I/O, L170P_Y I/O, L170N 6 T8 XC2S600E - I/O, L170N I/O, L170N_Y I/O, L169P 6 U2 XC2S400E - I/O, L169P_Y I/O, L169P I/O, L169N 6 U3 XC2S400E - I/O, L169N_Y I/O, L169N I/O 6 U7 - - - I/O I/O, L168P 6 U4 XC2S600E - - I/O, L168P_Y I/O, L168N 6 U5 XC2S600E - I/O I/O, L168N_Y I/O 6 U8 - - I/O I/O I/O, L167P_YY 6 V1 All - I/O, L167P_YY I/O, L167P_YY I/O, L167N_YY 6 V2 All - I/O, L167N_YY I/O, L167N_YY I/O 6 V3 - - I/O I/O I/O, VREF Bank 6, L166P_YY 6 V4 All All I/O, VREF Bank 6, L166P_YY I/O, VREF Bank 6, L166P_YY I/O, L166N_YY 6 V5 All - I/O, L166N_YY I/O, L166N_YY I/O, L165P_YY 6 V6 All - I/O, L165P_YY I/O, L165P_YY I/O, L165N_YY 6 V7 All - I/O, L165N_YY I/O, L165N_YY I/O 6 V8 - - - I/O I/O, L164P 6 W1 XC2S600E - I/O, L164P I/O, L164P_Y 92 www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L164N 6 W2 XC2S600E XC2S600E I/O, L164N I/O, VREF Bank 6, L164N_Y I/O, L163P 6 W5 XC2S400E - I/O, L163P_Y I/O, L163P I/O, L163N 6 W6 XC2S400E - I/O, L163N_Y I/O, L163N I/O 6 W7 - - I/O I/O I/O, L162P_YY 6 Y1 All - I/O, L162P_YY I/O, L162P_YY I/O, L162N_YY 6 Y2 All - I/O, L162N_YY I/O, L162N_YY I/O 6 Y3 - - - I/O I/O, L161P_YY 6 Y4 All - I/O, L161P_YY I/O, L161P_YY I/O, VREF Bank 6, L161N_YY 6 Y5 All All I/O, VREF Bank 6, L161N_YY I/O, VREF Bank 6, L161N_YY I/O 6 Y6 - - I/O I/O I/O, L160P_YY 6 AA1 All - I/O, L160P_YY I/O, L160P_YY I/O, L160N_YY 6 AA2 All - I/O, L160N_YY I/O, L160N_YY I/O, L159P 6 AA3 XC2S600E - I/O, L159P I/O, L159P_Y I/O, L159N 6 AA4 XC2S600E - I/O, L159N I/O, L159N_Y I/O 6 Y7 - - - I/O I/O, L158P 6 AA5 XC2S600E - I/O, L158P I/O, L158P_Y I/O, VREF Bank 6, L158N 6 AB5 XC2S600E All I/O, VREF Bank 6, L158N I/O, VREF Bank 6, L158N_Y I/O, L157P 6 AB1 XC2S400E - I/O, L157P_Y I/O, L157P I/O, L157N 6 AB2 XC2S400E - I/O, L157N_Y I/O, L157N I/O, L156P 6 AC1 XC2S600E - - I/O, L156P_Y I/O, L156N 6 AC2 XC2S600E - I/O I/O, L156N_Y I/O, L155P_YY 6 AC3 All - I/O, L155P_YY I/O, L155P_YY I/O, L155N_YY 6 AB4 All - I/O, L155N_YY I/O, L155N_YY I/O, L154P 6 AD1 - - - I/O, L154P I/O, L154N 6 AD2 - - - I/O, L154N I/O, L153P_YY 6 AE1 All - I/O, L153P_YY I/O, L153P_YY I/O, L153N_YY 6 AF2 All - I/O, L153N_YY I/O, L153N_YY M1 - AE3 - - M1 M1 M0 - AF3 - - M0 M0 M2 - AD4 - - M2 M2 Function DS077-4 (2.3) June 18, 2008 Product Specification VREF Option XC2S400E XC2S600E www.xilinx.com 93 R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O 5 AC5 - - I/O I/O I/O, L152N 5 AE4 - - I/O I/O, L152N I/O, L152P 5 AF4 - - - I/O, L152P I/O, L151N 5 AE5 - - - I/O, L151N I/O, L151P 5 AF5 - - I/O I/O, L151P I/O, L150N 5 AA6 XC2S400E - I/O, L150N_Y I/O, L150N I/O, L150P 5 AB6 XC2S400E - I/O, L150P_Y I/O, L150P I/O, L149N_YY 5 AC6 All - I/O, L149N_YY I/O, L149N_YY I/O, L149P_YY 5 AD6 All - I/O, L149P_YY I/O, L149P_YY I/O, VREF Bank 5, L148N_YY 5 AE6 All All I/O, VREF Bank 5, L148N_YY I/O, VREF Bank 5, L148N_YY I/O, L148P_YY 5 AF6 All - I/O, L148P_YY I/O, L148P_YY I/O, L147N 5 AA7 XC2S600E - - I/O, L147N_Y I/O, L147P 5 AB7 XC2S600E - I/O I/O, L147P_Y I/O, L146N_YY 5 AC7 All - I/O, L146N_YY I/O, L146N_YY I/O, L146P_YY 5 AD7 All - I/O, L146P_YY I/O, L146P_YY I/O, L145N_YY 5 AE7 All - I/O, L145N_YY I/O, L145N_YY I/O, L145P_YY 5 AF7 All - I/O, L145P_YY I/O, L145P_YY I/O, VREF Bank 5, L144N_YY 5 Y8 All All I/O, VREF Bank 5, L144N_YY I/O, VREF Bank 5, L144N_YY I/O, L144P_YY 5 AA8 All - I/O, L144P_YY I/O, L144P_YY I/O, L143N_YY 5 AE8 All - I/O, L143N_YY I/O, L143N_YY I/O, L143P_YY 5 AF8 All - I/O, L143P_YY I/O, L143P_YY I/O 5 AB8 - - I/O I/O I/O, L142N 5 W9 XC2S600E - I/O, L142N I/O, L142N_Y I/O, L142P 5 Y9 XC2S600E - I/O, L142P I/O, L142P_Y I/O, L141N 5 AA9 XC2S600E XC2S600E - I/O, VREF Bank 5, L141N_Y I/O, L141P 5 AB9 XC2S600E - I/O I/O, L141P_Y I/O, L140N_YY 5 AC9 All - I/O, L140N_YY I/O, L140N_YY I/O, L140P_YY 5 AD9 All - I/O, L140P_YY I/O, L140P_YY I/O, L139N_YY 5 AE9 All - I/O, L139N_YY I/O, L139N_YY I/O, L139P_YY 5 AF9 All - I/O, L139P_YY I/O, L139P_YY I/O, VREF Bank 5, L138N_YY 5 W10 All All I/O, VREF Bank 5, L138N_YY I/O, VREF Bank 5, L138N_YY Function 94 VREF Option XC2S400E XC2S600E www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L138P_YY 5 Y10 All - I/O, L138P_YY I/O, L138P_YY I/O, L137N_YY 5 AB10 All - I/O, L137N_YY I/O, L137N_YY I/O, L137P_YY 5 AC10 All - I/O, L137P_YY I/O, L137P_YY I/O 5 AD10 - - - I/O I/O, L136N 5 AE10 XC2S600E - I/O, L136N I/O, L136N_Y I/O, L136P 5 AF10 XC2S600E - I/O, L136P I/O, L136P_Y I/O 5 AD11 - - - I/O I/O, L135N_YY 5 W11 All - I/O, L135N_YY I/O, L135N_YY I/O, L135P_YY 5 Y11 All - I/O, L135P_YY I/O, L135P_YY I/O, L134N_YY 5 AA11 All - I/O, L134N_YY I/O, L134N_YY I/O, L134P_YY 5 AB11 All - I/O, L134P_YY I/O, L134P_YY I/O 5 V12 - - - I/O I/O, L133N 5 AE11 - - I/O, L133N I/O, L133N I/O, L133P 5 AF11 - - I/O, L133P I/O, L133P I/O 5 W12 - - - I/O I/O, L132N_YY 5 Y12 All - I/O, L132N_YY I/O, L132N_YY I/O, L132P_YY 5 AA12 All - I/O, L132P_YY I/O, L132P_YY I/O, VREF Bank 5, L131N_YY 5 AB12 All All I/O, VREF Bank 5, L131N_YY I/O, VREF Bank 5, L131N_YY I/O, L131P_YY 5 AC12 All - I/O, L131P_YY I/O, L131P_YY I/O 5 V13 - - - I/O I/O, L130N_YY 5 AE12 All - I/O, L130N_YY I/O, L130N_YY I/O, L130P_YY 5 AF12 All - I/O, L130P_YY I/O, L130P_YY I/O 5 W13 - - - I/O I/O, L129N 5 Y13 XC2S600E - I/O, L129N I/O, L129N_Y I/O, L129P 5 AA13 XC2S600E - I/O, L129P I/O, L129P_Y I/O, VREF Bank 5, L128N 5 AB13 XC2S600E All I/O, VREF Bank 5, L128N I/O, VREF Bank 5, L128N_Y I/O, L128P 5 AC13 XC2S600E - I/O, L128P I/O, L128P_Y I/O 5 AD13 - - - I/O I/O, L127N 5 V14 - - I/O I/O, L127N I/O, L127P 5 W14 - - - I/O, L127P I/O (DLL), L126N 5 AE13 - - I/O (DLL), L126N I/O (DLL), L126N GCK1, I 5 AF13 - - GCK1, I GCK1, I Function DS077-4 (2.3) June 18, 2008 Product Specification VREF Option XC2S400E XC2S600E www.xilinx.com 95 R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option GCK0, I 4 AF14 - - GCK0, I GCK0, I I/O (DLL), L126P 4 AE14 - - I/O (DLL), L126P I/O (DLL), L126P I/O 4 AD14 - - - I/O I/O, L125N 4 AC14 - - I/O, L125N I/O, L125N I/O, L125P 4 AB14 - - I/O, L125P I/O, L125P I/O 4 AC15 - - - I/O I/O, L124N 4 AA14 XC2S600E - I/O, L124N I/O, L124N_Y I/O, VREF Bank 4, L124P 4 Y14 XC2S600E All I/O, VREF Bank 4, L124P I/O, VREF Bank 4, L124P_Y I/O, L123N 4 AF15 XC2S600E - I/O, L123N I/O, L123N_Y I/O, L123P 4 AE15 XC2S600E - I/O, L123P I/O, L123P_Y I/O 4 AB15 - - - I/O I/O, L122N_YY 4 AA15 All - I/O, L122N_YY I/O, L122N_YY I/O, L122P_YY 4 Y15 All - I/O, L122P_YY I/O, L122P_YY I/O 4 AF16 - - - I/O I/O, L121N_YY 4 W15 All - I/O, L121N_YY I/O, L121N_YY I/O, VREF Bank 4, L121P_YY 4 V15 All All I/O, VREF Bank 4, L121P_YY I/O, VREF Bank 4, L121P_YY I/O, L120N_YY 4 AE16 All - I/O, L120N_YY I/O, L120N_YY I/O, L120P_YY 4 AD16 All - I/O, L120P_YY I/O, L120P_YY I/O 4 AB16 - - - I/O I/O, L119N 4 AA16 - - I/O, L119N I/O, L119N I/O, L119P 4 Y16 - - I/O, L119P I/O, L119P I/O 4 W16 - - - I/O I/O, L118N_YY 4 AF17 All - I/O, L118N_YY I/O, L118N_YY I/O, L118P_YY 4 AE17 All - I/O, L118P_YY I/O, L118P_YY I/O, L117N_YY 4 AD17 All - I/O, L117N_YY I/O, L117N_YY I/O, L117P_YY 4 AC17 All - I/O, L117P_YY I/O, L117P_YY I/O 4 AB17 - - - I/O I/O, L116N 4 Y17 XC2S600E - I/O, L116N I/O, L116N_Y I/O, L116P 4 W17 XC2S600E - I/O, L116P I/O, L116P_Y I/O 4 AF18 - - - I/O I/O, L115N_YY 4 AE18 All - I/O, L115N_YY I/O, L115N_YY I/O, L115P_YY 4 AD18 All - I/O, L115P_YY I/O, L115P_YY Function 96 VREF Option XC2S400E XC2S600E www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O 4 AC18 - - I/O I/O I/O, VREF Bank 4, L114N 4 AB18 - All I/O, VREF Bank 4, L114N I/O, VREF Bank 4, L114N I/O, L114P 4 AA18 - - I/O, L114P I/O, L114P I/O, L113N 4 Y18 - - I/O, L113N I/O, L113N I/O, L113P 4 W18 - - I/O, L113P I/O, L113P I/O 4 AB19 - - I/O I/O I/O, L112N 4 AF19 XC2S600E - I/O I/O, L112N_Y I/O, L112P 4 AE19 XC2S600E XC2S600E - I/O, VREF Bank 4, L112P_Y I/O, L111N 4 AA19 XC2S600E - I/O, L111N I/O, L111N_Y I/O, L111P 4 Y19 XC2S600E - I/O, L111P I/O, L111P_Y I/O 4 AF20 - - - I/O I/O, L110N 4 AE20 XC2S600E - I/O, L110N I/O, L110N_Y I/O, L110P 4 AD20 XC2S600E - I/O, L110P I/O, L110P_Y I/O 4 AC20 - - I/O I/O I/O, L109N_YY 4 AB20 All - I/O, L109N_YY I/O, L109N_YY I/O, VREF Bank 4, L109P_YY 4 AA20 All All I/O, VREF Bank 4, L109P_YY I/O, VREF Bank 4, L109P_YY I/O 4 Y20 - - I/O I/O I/O, L108N 4 AF21 - - I/O, L108N I/O, L108N I/O, L108P 4 AE21 - - I/O, L108P I/O, L108P I/O, L107N 4 AD21 - - I/O, L107N I/O, L107N I/O, L107P 4 AC21 - - I/O, L107P I/O, L107P I/O 4 AC22 - - - I/O I/O, L106N_YY 4 AF22 All - I/O, L106N_YY I/O, L106N_YY I/O, VREF Bank 4, L106P_YY 4 AE22 All All I/O, VREF Bank 4, L106P_YY I/O, VREF Bank 4, L106P_YY I/O, L105N_YY 4 AB21 All - I/O, L105N_YY I/O, L105N_YY I/O, L105P_YY 4 AA21 All - I/O, L105P_YY I/O, L105P_YY I/O, L104N_YY 4 AF23 All - I/O, L104N_YY I/O, L104N_YY I/O, L104P_YY 4 AE23 All - I/O, L104P_YY I/O, L104P_YY I/O, L103N 4 AD23 XC2S600E - I/O I/O, L103N_Y I/O, L103P 4 AE24 XC2S600E - - I/O, L103P_Y I/O, L102N_YY 4 AF24 All - I/O, L102N_YY I/O, L102N_YY I/O, L102P_YY 4 AF25 All - I/O, L102P_YY I/O, L102P_YY Function DS077-4 (2.3) June 18, 2008 Product Specification VREF Option XC2S400E XC2S600E www.xilinx.com 97 R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option DONE 3 AE26 - - DONE DONE PROGRAM - AC24 - - PROGRAM PROGRAM I/O (INIT), L101N_YY 3 AD25 All - I/O (INIT), L101N_YY I/O (INIT), L101N_YY I/O (D7), L101P_YY 3 AD26 All - I/O (D7), L101P_YY I/O (D7), L101P_YY I/O, L100N 3 AC25 - - - I/O, L100N I/O, L100P 3 AC26 - - - I/O, L100P I/O, L99N 3 AB22 XC2S600E - - I/O, L99N_Y I/O, L99P 3 AB23 XC2S600E - I/O I/O, L99P_Y I/O, L98N_YY 3 AB25 All - I/O, L98N_YY I/O, L98N_YY I/O, L98P_YY 3 AB26 All - I/O, L98P_YY I/O, L98P_YY I/O, L97N 3 AA23 - - I/O, L97N_Y I/O, L97N I/O, L97P 3 AA24 - - I/O, L97P_Y I/O, L97P I/O, VREF Bank 3, L96N 3 AA25 XC2S600E All I/O, VREF Bank 3, L96N I/O, VREF Bank 3, L96N_Y I/O, L96P 3 AA26 XC2S600E - I/O, L96P I/O, L96P_Y I/O, L95N 3 AA22 XC2S600E - - I/O, L95N_Y I/O, L95P 3 Y22 XC2S600E - I/O I/O, L95P_Y I/O, L94N 3 Y23 XC2S400E - I/O, L94N_Y I/O, L94N I/O, L94P 3 Y24 XC2S400E - I/O, L94P_Y I/O, L94P I/O, L93N 3 Y25 XC2S600E - I/O, L93N I/O, L93N_Y I/O, L93P 3 Y26 XC2S600E - I/O, L93P I/O, L93P_Y I/O, VREF Bank 3, L92N_YY 3 W21 All All I/O, VREF Bank 3, L92N_YY I/O, VREF Bank 3, L92N_YY I/O, L92P_YY 3 W22 All - I/O, L92P_YY I/O, L92P_YY I/O 3 Y21 - - - I/O I/O, L91N_YY 3 W25 All - I/O, L91N_YY I/O, L91N_YY I/O, L91P_YY 3 W26 All - I/O, L91P_YY I/O, L91P_YY I/O 3 W20 - - I/O I/O I/O, L90N 3 V19 XC2S400E - I/O, L90N_Y I/O, L90N I/O, L90P 3 V20 XC2S400E - I/O, L90P_Y I/O, L90P I/O, L89N 3 V21 XC2S600E XC2S600E - I/O, VREF Bank 3, L89N_Y I/O, L89P 3 V22 XC2S600E - I/O I/O, L89P_Y I/O 3 V23 - - I/O I/O I/O, L88N_YY 3 V24 All - I/O, L88N_YY I/O, L88N_YY Function 98 VREF Option XC2S400E XC2S600E www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L88P_YY 3 V25 All - I/O, L88P_YY I/O, L88P_YY I/O 3 V26 - - I/O I/O I/O, VREF Bank 3, L87N_YY 3 U19 All All I/O, VREF Bank 3, L87N_YY I/O, VREF Bank 3, L87N_YY I/O (D6), L87P_YY 3 U20 All - I/O (D6), L87P_YY I/O (D6), L87P_YY I/O (D5), L86N_YY 3 U22 All - I/O (D5), L86N_YY I/O (D5), L86N_YY I/O, L86P_YY 3 U23 All - I/O, L86P_YY I/O, L86P_YY I/O 3 U24 - - - I/O I/O, L85N 3 U25 XC2S600E - - I/O, L85N_Y I/O, L85P 3 U26 XC2S600E - I/O I/O, L85P_Y I/O 3 R18 - - I/O I/O I/O, L84N 3 T19 XC2S400E - I/O, L84N_Y I/O, L84N I/O, L84P 3 T20 XC2S400E - I/O, L84P_Y I/O, L84P I/O, L83N 3 T21 XC2S600E - I/O, L83N I/O, L83N_Y I/O, L83P 3 T22 XC2S600E - I/O, L83P I/O, L83P_Y I/O 3 T24 - - - I/O I/O, L82N 3 T25 XC2S600E - I/O, L82N I/O, L82N_Y I/O, L82P 3 T26 XC2S600E - I/O, L82P I/O, L82P_Y I/O 3 R19 - - - I/O I/O, L81N 3 R20 XC2S600E - I/O, L81N I/O, L81N_Y I/O, L81P 3 R21 XC2S600E - I/O, L81P I/O, L81P_Y I/O, VREF Bank 3, L80N_YY 3 R22 All All I/O, VREF Bank 3, L80N_YY I/O, VREF Bank 3, L80N_YY I/O (D4), L80P_YY 3 R23 All - I/O (D4), L80P_YY I/O (D4), L80P_YY I/O 3 P18 - - - I/O I/O, L79N_YY 3 R25 All - I/O, L79N_YY I/O, L79N_YY I/O, L79P_YY 3 R26 All - I/O, L79P_YY I/O, L79P_YY I/O 3 P19 - - - I/O I/O, L78N 3 P20 XC2S400E - I/O, L78N_Y I/O, L78N I/O, L78P 3 P21 XC2S400E - I/O, L78P_Y I/O, L78P I/O, VREF Bank 3, L77N 3 P22 XC2S600E All I/O, VREF Bank 3, L77N I/O, VREF Bank 3, L77N_Y I/O, L77P 3 P23 XC2S600E - I/O, L77P I/O, L77P_Y I/O 3 P24 - - - I/O I/O, L76N_YY 3 P25 All - I/O, L76N_YY I/O, L76N_YY I/O, L76P_YY 3 P26 All - I/O, L76P_YY I/O, L76P_YY Function DS077-4 (2.3) June 18, 2008 Product Specification VREF Option XC2S400E XC2S600E www.xilinx.com 99 R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O 3 N18 - - - I/O I/O (TRDY) 3 N24 - - I/O (TRDY) I/O (TRDY) I/O (IRDY), L75N_YY 2 N26 All - I/O (IRDY), L75N_YY I/O (IRDY), L75N_YY I/O, L75P_YY 2 N25 All - I/O, L75P_YY I/O, L75P_YY I/O 2 N19 - - - I/O I/O, L74N 2 N23 XC2S600E - - I/O, L74N_Y I/O, L74P 2 N22 XC2S600E - I/O I/O, L74P_Y I/O 2 M23 - - I/O I/O I/O, L73N 2 N21 XC2S600E - I/O, L73N I/O, L73N_Y I/O, VREF Bank 2, L73P 2 N20 XC2S600E All I/O, VREF Bank 2, L73P I/O, VREF Bank 2, L73P_Y I/O, L72N 2 M26 XC2S400E - I/O, L72N_Y I/O, L72N I/O, L72P 2 M25 XC2S400E - I/O, L72P_Y I/O, L72P I/O 2 M22 - - - I/O I/O, L71N_YY 2 M21 All - I/O, L71N_YY I/O, L71N_YY I/O, L71P_YY 2 M20 All - I/O, L71P_YY I/O, L71P_YY I/O 2 L26 - - - I/O I/O (D3), L70N_YY 2 M19 All - I/O (D3), L70N_YY I/O (D3), L70N_YY I/O, VREF Bank 2, L70P_YY 2 M18 All All I/O, VREF Bank 2, L70P_YY I/O, VREF Bank 2, L70P_YY I/O, L69N 2 L25 XC2S600E - I/O, L69N I/O, L69N_Y I/O, L69P 2 L24 XC2S600E - I/O, L69P I/O, L69P_Y I/O 2 L22 - - - I/O I/O, L68N 2 L21 XC2S600E - I/O, L68N I/O, L68N_Y I/O, L68P 2 L20 XC2S600E - I/O, L68P I/O, L68P_Y I/O 2 L19 - - - I/O I/O, L67N 2 K26 XC2S600E - I/O, L67N I/O, L67N_Y I/O, L67P 2 K25 XC2S600E - I/O, L67P I/O, L67P_Y I/O, L66N 2 K24 - - - I/O, L66N I/O, L66P 2 K23 - - I/O I/O, L66P I/O 2 K22 - - - I/O I/O, L65N 2 K20 XC2S600E - I/O I/O, L65N_Y I/O, L65P 2 K19 XC2S600E - I/O I/O, L65P_Y I/O 2 J26 - - I/O I/O Function 100 VREF Option XC2S400E XC2S600E www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L64N_YY 2 J25 All - I/O, L64N_YY I/O, L64N_YY I/O (D2), L64P_YY 2 J24 All - I/O (D2), L64P_YY I/O (D2), L64P_YY I/O (D1) 2 J23 - - I/O (D1) I/O (D1) I/O, VREF Bank 2, L63N_YY 2 J22 All All I/O, VREF Bank 2, L63N_YY I/O, VREF Bank 2, L63N_YY I/O, L63P_YY 2 J21 All - I/O, L63P_YY I/O, L63P_YY I/O, L62N_YY 2 J20 All - I/O, L62N_YY I/O, L62N_YY I/O, L62P_YY 2 J19 All - I/O, L62P_YY I/O, L62P_YY I/O 2 H22 - - I/O I/O I/O, L61N 2 H26 XC2S600E - I/O I/O, L61N_Y I/O, L61P 2 H25 XC2S600E XC2S600E - I/O, VREF Bank 2, L61P_Y I/O, L60N 2 H21 XC2S400E - I/O, L60N_Y I/O, L60N I/O, L60P 2 H20 XC2S400E - I/O, L60P_Y I/O, L60P I/O 2 G26 - - - I/O I/O, L59N_YY 2 G25 All - I/O, L59N_YY I/O, L59N_YY I/O, L59P_YY 2 G24 All - I/O, L59P_YY I/O, L59P_YY I/O 2 G23 - - I/O I/O I/O, L58N_YY 2 G22 All - I/O, L58N_YY I/O, L58N_YY I/O, VREF Bank 2, L58P_YY 2 G21 All All I/O, VREF Bank 2, L58P_YY I/O, VREF Bank 2, L58P_YY I/O 2 G20 - - I/O I/O I/O, L57N_YY 2 F26 All - I/O, L57N_YY I/O, L57N_YY I/O, L57P_YY 2 F25 All - I/O, L57P_YY I/O, L57P_YY I/O, L56N 2 F24 XC2S600E - I/O, L56N I/O, L56N_Y I/O, L56P 2 F23 XC2S600E - I/O, L56P I/O, L56P_Y I/O 2 F22 - - - I/O I/O, L55N 2 E26 XC2S600E - I/O, L55N I/O, L55N_Y I/O, VREF Bank 2, L55P 2 E25 XC2S600E All I/O, VREF Bank 2, L55P I/O, VREF Bank 2, L55P_Y I/O, L54N 2 E23 XC2S400E - I/O, L54N_Y I/O, L54N I/O, L54P 2 E22 XC2S400E - I/O, L54P_Y I/O, L54P I/O, L53N_YY 2 F21 All - I/O, L53N_YY I/O, L53N_YY I/O, L53P_YY 2 E21 All - I/O, L53P_YY I/O, L53P_YY I/O, L52N 2 D26 XC2S600E - I/O I/O, L52N_Y I/O, L52P 2 D25 XC2S600E - - I/O, L52P_Y Function DS077-4 (2.3) June 18, 2008 Product Specification VREF Option XC2S400E XC2S600E www.xilinx.com 101 R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L51N 2 D24 - - - I/O, L51N I/O, L51P 2 C25 - - - I/O, L51P I/O (DIN, D0), L50N_YY 2 C26 All - I/O (DIN, D0), L50N_YY I/O (DIN, D0), L50N_YY I/O (DOUT, BUSY), L50P_YY 2 B26 All - I/O (DOUT, BUSY), L50P_YY I/O (DOUT, BUSY), L50P_YY CCLK 2 A25 - - CCLK CCLK TDO 2 C23 - - TDO TDO TDI - D22 - - TDI TDI I/O (CS), L49P_YY 1 B24 All - I/O (CS), L49P_YY I/O (CS), L49P_YY I/O (WRITE), L49N_YY 1 A24 All - I/O (WRITE), L49N_YY I/O (WRITE), L49N_YY I/O, L48P 1 B23 - - I/O I/O, L48P I/O, L48N 1 A23 - - - I/O, L48N I/O, L47P 1 B22 XC2S400E - I/O, L47P_Y I/O, L47P I/O, L47N 1 A22 XC2S400E - I/O, L47N_Y I/O, L47N I/O, L46P_YY 1 D21 All - I/O, L46P_YY I/O, L46P_YY I/O, L46N_YY 1 C21 All - I/O, L46N_YY I/O, L46N_YY I/O, VREF Bank 1, L45P_YY 1 B21 All All I/O, VREF Bank 1, L45P_YY I/O, VREF Bank 1, L45P_YY I/O, L45N_YY 1 A21 All - I/O, L45N_YY I/O, L45N_YY I/O, L44P 1 F20 XC2S600E - - I/O, L44P_Y I/O, L44N 1 E20 XC2S600E - I/O I/O, L44N_Y I/O, L43P_YY 1 D20 All - I/O, L43P_YY I/O, L43P_YY I/O, L43N_YY 1 C20 All - I/O, L43N_YY I/O, L43N_YY I/O, L42P_YY 1 B20 All - I/O, L42P_YY I/O, L42P_YY I/O, L42N_YY 1 A20 All - I/O, L42N_YY I/O, L42N_YY I/O, VREF Bank 1, L41P_YY 1 G19 All All I/O, VREF Bank 1, L41P_YY I/O, VREF Bank 1, L41P_YY I/O, L41N_YY 1 F19 All - I/O, L41N_YY I/O, L41N_YY I/O 1 E19 - - - I/O I/O, L40P_YY 1 B19 All - I/O, L40P_YY I/O, L40P_YY I/O, L40N_YY 1 A19 All - I/O, L40N_YY I/O, L40N_YY I/O 1 H18 - - I/O I/O I/O, L39P 1 G18 XC2S600E - I/O, L39P I/O, L39P_Y Function 102 VREF Option XC2S400E XC2S600E www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L39N 1 F18 XC2S600E - I/O, L39N I/O, L39N_Y I/O, L38P 1 D18 XC2S600E XC2S600E - I/O, VREF Bank 1, L38P_Y I/O, L38N 1 C18 XC2S600E - I/O I/O, L38N_Y I/O, L37P_YY 1 B18 All - I/O, L37P_YY I/O, L37P_YY I/O, L37N_YY 1 A18 All - I/O, L37N_YY I/O, L37N_YY I/O, L36P_YY 1 H17 All - I/O, L36P_YY I/O, L36P_YY I/O, L36N_YY 1 G17 All - I/O, L36N_YY I/O, L36N_YY I/O, VREF Bank 1, L35P_YY 1 E18 All All I/O, VREF Bank 1, L35P_YY I/O, VREF Bank 1, L35P_YY I/O, L35N_YY 1 E17 All - I/O, L35N_YY I/O, L35N_YY I/O, L34P_YY 1 D17 All - I/O, L34P_YY I/O, L34P_YY I/O, L34N_YY 1 C17 All - I/O, L34N_YY I/O, L34N_YY I/O 1 H16 - - - I/O I/O, L33P 1 B17 XC2S600E - I/O, L33P I/O, L33P_Y I/O, L33N 1 A17 XC2S600E - I/O, L33N I/O, L33N_Y I/O 1 G16 - - - I/O I/O, L32P_YY 1 F16 All - I/O, L32P_YY I/O, L32P_YY I/O, L32N_YY 1 E16 All - I/O, L32N_YY I/O, L32N_YY I/O, L31P_YY 1 C16 All - I/O, L31P_YY I/O, L31P_YY I/O, L31N_YY 1 B16 All - I/O, L31N_YY I/O, L31N_YY I/O 1 A16 - - - I/O I/O, L30P 1 J15 - - I/O, L30P I/O, L30P I/O, L30N 1 H15 - - I/O, L30N I/O, L30N I/O 1 G15 - - - I/O I/O, L29P_YY 1 F15 All - I/O, L29P_YY I/O, L29P_YY I/O, L29N_YY 1 E15 All - I/O, L29N_YY I/O, L29N_YY I/O, VREF Bank 1, L28P_YY 1 B15 All All I/O, VREF Bank 1, L28P_YY I/O, VREF Bank 1, L28P_YY I/O, L28N_YY 1 A15 All - I/O, L28N_YY I/O, L28N_YY I/O 1 D15 - - - I/O I/O, L27P_YY 1 J14 All - I/O, L27P_YY I/O, L27P_YY I/O, L27N_YY 1 H14 All - I/O, L27N_YY I/O, L27N_YY I/O 1 G14 - - - I/O I/O, L26P 1 F14 XC2S600E - I/O, L26P I/O, L26P_Y I/O, L26N 1 E14 XC2S600E - I/O, L26N I/O, L26N_Y Function DS077-4 (2.3) June 18, 2008 Product Specification VREF Option XC2S400E XC2S600E www.xilinx.com 103 R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Bank Pin LVDS Async. Output Option I/O, VREF Bank 1, L25P 1 D14 XC2S600E I/O, L25N 1 C14 I/O 1 I/O, L24P Function VREF Option Device-Specific Pinouts XC2S400E XC2S600E All I/O, VREF Bank 1, L25P I/O, VREF Bank 1, L25P_Y XC2S600E - I/O, L25N I/O, L25N_Y J13 - - - I/O 1 C13 - - I/O, L24P I/O, L24P I/O, L24N 1 D13 - - I/O, L24N I/O, L24N I/O 1 H13 - - - I/O I/O (DLL), L23P 1 B14 - - I/O (DLL), L23P I/O (DLL), L23P GCK2, I 1 A14 - - GCK2, I GCK2, I GCK3, I 0 A13 - - GCK3, I GCK3, I I/O (DLL), L23N 0 B13 - - I/O (DLL), L23N I/O (DLL), L23N I/O 0 E13 - - - I/O I/O, L22P_YY 0 F13 All - I/O, L22P_YY I/O, L22P_YY I/O, L22N_YY 0 G13 All - I/O, L22N_YY I/O, L22N_YY I/O, L21P 0 A12 XC2S600E - - I/O, L21P_Y I/O, VREF Bank 0, L21N 0 B12 XC2S600E All I/O, VREF Bank 0 I/O, VREF Bank 0, L21N_Y I/O, L20P 0 D12 XC2S600E - I/O, L20P I/O, L20P_Y I/O, L20N 0 E12 XC2S600E - I/O, L20N I/O, L20N_Y I/O 0 F12 - - - I/O I/O, L19P_YY 0 G12 All - I/O, L19P_YY I/O, L19P_YY I/O, L19N_YY 0 H12 All - I/O, L19N_YY I/O, L19N_YY I/O 0 J12 - - - I/O I/O, L18P_YY 0 A11 All - I/O, L18P_YY I/O, L18P_YY I/O, VREF Bank 0, L18N_YY 0 B11 All All I/O, VREF Bank 0, L18N_YY I/O, VREF Bank 0, L18N_YY I/O, L17P_YY 0 E11 All - I/O, L17P_YY I/O, L17P_YY I/O, L17N_YY 0 F11 All - I/O, L17N_YY I/O, L17N_YY I/O 0 C11 - - - I/O I/O, L16P 0 G11 - - I/O, L16P I/O, L16P I/O, L16N 0 H11 - - I/O, L16N I/O, L16N I/O 0 C10 - - - I/O I/O, L15P_YY 0 A10 All - I/O, L15P_YY I/O, L15P_YY I/O, L15N_YY 0 B10 All - I/O, L15N_YY I/O, L15N_YY I/O, L14P_YY 0 D10 All - I/O, L14P_YY I/O, L14P_YY 104 www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L14N_YY 0 E10 All - I/O, L14N_YY I/O, L14N_YY I/O 0 G10 - - - I/O I/O, L13P 0 A9 XC2S600E - I/O, L13P I/O, L13P_Y I/O, L13N 0 B9 XC2S600E - I/O, L13N I/O, L13N_Y I/O 0 H10 - - - I/O I/O, L12P_YY 0 C9 All - I/O, L12P_YY I/O, L12P_YY I/O, L12N_YY 0 D9 All - I/O, L12N_YY I/O, L12N_YY I/O 0 E9 - - I/O I/O I/O, VREF Bank 0, L11P 0 F9 - All I/O, VREF Bank 0, L11P I/O, VREF Bank 0, L11P I/O, L11N 0 G9 - - I/O, L11N I/O, L11N I/O, L10P 0 A8 - - I/O, L10P I/O, L10P I/O, L10N 0 B8 - - I/O, L10N I/O, L10N I/O 0 H9 - - I/O I/O I/O, L9P 0 E8 XC2S600E - I/O I/O, L9P_Y I/O, L9N 0 F8 XC2S600E XC2S600E - I/O, VREF Bank 0, L9N_Y I/O, L8P 0 A7 XC2S600E - I/O, L8P I/O, L8P_Y I/O, L8N 0 B7 XC2S600E - I/O, L8N I/O, L8N_Y I/O 0 G8 - - I/O I/O I/O, L7P_YY 0 C7 All - I/O, L7P_YY I/O, L7P_YY I/O, L7N_YY 0 D7 All - I/O, L7N_YY I/O, L7N_YY I/O 0 E7 - - - I/O I/O, L6P_YY 0 F7 All - I/O, L6P_YY I/O, L6P_YY I/O, VREF Bank 0, L6N_YY 0 G7 All All I/O, VREF Bank 0, L6N_YY I/O, VREF Bank 0, L6N_YY I/O 0 A6 - - I/O I/O I/O, L5P 0 B6 - - I/O, L5P I/O, L5P I/O, L5N 0 C6 - - I/O, L5N I/O, L5N I/O, L4P 0 D6 - - I/O, L4P I/O, L4P I/O, L4N 0 E6 - - I/O, L4N I/O, L4N I/O 0 F6 - - - I/O I/O, L3P_YY 0 A5 All - I/O, L3P_YY I/O, L3P_YY I/O, VREF Bank 0, L3N_YY 0 B5 All All I/O, VREF Bank 0, L3N_YY I/O, VREF Bank 0, L3N_YY I/O, L2P_YY 0 D5 All - I/O, L2P_YY I/O, L2P_YY Function DS077-4 (2.3) June 18, 2008 Product Specification VREF Option XC2S400E XC2S600E www.xilinx.com 105 R Spartan-IIE FPGA Family: Pinout Tables FG676 Pinouts (XC2S400E, XC2S600E) (Continued) Pad Name Device-Specific Pinouts Bank Pin LVDS Async. Output Option I/O, L2N_YY 0 E5 All - I/O, L2N_YY I/O, L2N_YY I/O, L1P_YY 0 B4 All - I/O, L1P_YY I/O, L1P_YY I/O, L1N_YY 0 C4 All - I/O, L1N_YY I/O, L1N_YY I/O, L0P 0 A3 XC2S600E - I/O I/O, L0P_Y I/O, L0N 0 B3 XC2S600E - - I/O, L0N_Y I/O 0 A4 - - I/O I/O TCK - A2 - - TCK TCK Function VREF Option XC2S400E XC2S600E FG676 Differential Clock Pins P Input N Input Clock Bank Pin Name Pin Name GCK0 4 AF14 GCK0, I AE14 I/O (DLL), L126P GCK1 5 AF13 GCK1, I AE13 I/O (DLL), L126N GCK2 1 A14 GCK2, I B14 I/O (DLL), L23P GCK3 0 A13 GCK3, I B13 I/O (DLL), L23N Additional FG676 Package Pins VCCINT Pins H8 H19 J9 J18 K10 K11 K16 K17 L10 L17 T10 T17 U10 U11 U16 U17 V9 V18 W8 W19 - C8 D11 J10 J11 K12 K13 C22 D16 J16 J17 K14 K15 H24 K18 L18 L23 M17 N17 R17 T18 T23 U18 W24 AB24 U15 V16 V17 AC16 AD19 AD22 U13 V10 V11 AC11 AD5 AD8 R10 T4 T9 U9 W3 AB3 K9 L4 L9 M10 N10 E3 VCCO Bank 0 Pins C5 VCCO Bank 1 Pins C19 VCCO Bank 2 Pins E24 VCCO Bank 3 Pins P17 VCCO Bank 4 Pins U14 VCCO Bank 5 Pins U12 VCCO Bank 6 Pins P10 VCCO Bank 7 Pins H3 106 www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification R Spartan-IIE FPGA Family: Pinout Tables Additional FG676 Package Pins (Continued) GND Pins A1 A26 B2 B25 C3 C12 C15 C24 D4 D8 D19 D23 F10 F17 H4 H23 K6 K21 L11 L12 L13 L14 L15 L16 M3 M11 M12 M13 M14 M15 M16 M24 N11 N12 N13 N14 N15 N16 P11 P12 P13 P14 P15 P16 R3 R11 R12 R13 R14 R15 R16 R24 T11 T12 T13 T14 T15 T16 U6 U21 W4 W23 AA10 AA17 AC4 AC8 AC19 AC23 AD3 AD12 AD15 AD24 AE2 AE25 AF1 AF26 - Not Connected Pins (XC2S400E Only) A12 A16 A23 B3 C1 C2 C10 C11 C25 D2 D15 D18 D24 D25 E7 E13 E19 F2 F6 F8 F12 F20 F22 G10 G14 G15 G16 G26 H10 H13 H16 H25 J6 J8 J12 J13 K1 K4 K22 K24 L3 L19 L22 L26 M4 M9 M22 N1 N4 N9 N18 N19 N23 P4 P5 P18 P19 P24 R4 R7 R19 T3 T24 U1 U4 U7 U24 U25 V8 V12 V13 V21 W12 W13 W14 W16 Y3 Y7 Y21 AA7 AA9 AA22 AB15 AB16 AB17 AB22 AC1 AC15 AC22 AC25 AC26 AD1 AD2 AD10 AD11 AD13 AD14 AE5 AE19 AE24 AF4 AF16 AF18 AF20 - DS077-4 (2.3) June 18, 2008 Product Specification www.xilinx.com 107 R Spartan-IIE FPGA Family: Pinout Tables Revision History Version No. Date 1.0 11/15/01 Initial Xilinx release. 1.1 12/20/01 Corrected differential pin pair designations. 2.0 11/18/02 Added XC2S400E and XC2S600E and FG676. Removed L37 designation from FT256 pinouts. Minor corrections and clarifications to pinout definitions. Removed Preliminary designation. 2.1 02/14/03 Added differential pairs table on page 57, fixed 3 P/N designation typos introduced in v2.0. Clarified that XC2S50E has two VREF pins per bank. 2.3 06/18/08 Added Package Overview section. Updated all modules for continuous page, figure, and table numbering. Updated links. Synchronized all modules to v2.3. 108 Description www.xilinx.com DS077-4 (2.3) June 18, 2008 Product Specification