IL260/IL261/IL262
IsoLoop is a registered trademark of NVE Corporation.
*U.S. Patent number 5,831,426; 6,300,617 and others.
REV. M
NVE Corporation 11409 Valley View Road, Eden Prairie, MN 55344-3617 Phone: ( 952) 829-9217 Fax: (952) 829-9189 www.IsoLoop.com ©NVE Corporation
High Speed Five-Channel Digital Isolators
Functional Diagrams
IN
1
IN
2
IN
3
IN
4
OUT
5
IN
5
OUT
1
OUT
2
OUT
3
OUT
4
OUT
1
OUT
2
OUT
3
OUT
4
OUT
5
IN
1
IN
2
IN
3
IN
4
IN
5
IL261
IL260
IN
1
IN
2
IN
3
OUT
4
OUT
5
IN
5
OUT
1
OUT
2
OUT
3
IN
4
IL262
Features
•
+5 V / +3.3 V CMOS/TTL Compatible
•
High Speed: 110 Mbps
• 1.5 mA/Channel Typical Quiescent Current
•
Extended Temperature Range (−40°C to +85°C)
•
2500 VRMS Isolation (1 min.)
•
2 ns Typical Pulse Width Distortion
•
100 ps Typical Pulse Jitter
•
4 ns Typical Propagation Delay Skew
•
10 ns Typical Propagation Delay
•
30 kV/µs Typical Common Mode Rejection
•
Low EMC Footprint
•
2 ns Channel-to-Channel Skew
•
0.3" and 0.15" 16-pin SOIC Packages
•
UL1577 and IEC 61010-2001 Approved
Applications
•
ADCs and DACs
•
Multiplexed Data Transmission
•
Data Interfaces
•
Board-to-Board Communication
•
Digital Noise Reduction
•
Operator Interface
•
Ground Loop Elimination
•
Peripheral Interfaces
•
Parallel Bus
•
Logic Level Shifting
•
Plasma Displays
Description
N
VE’s IL260-Series five-channel high-speed digital isolators are
CMOS devices manufactured with NVE’s patented* IsoLoop®
spintronic Giant Magnetoresistive (GMR) technology .
All transmit and receive channels operate at 110 Mbps over the full
temperature and supply voltage range. The symmetric magnetic
coupling barrier provides a typical propagation delay of only 10 ns
and a pulse width distortion of 2 ns, achieving the best specifications
of any isolator. The unique fifth channel can be is used to distribute
isolated clocks or handshake signals to multiple delta-sigma A/D
converters. High channel density makes these devices ideal for
isolating ADCs and DACs, parallel buses and peripheral interfaces.
Typical transient immunity of 30 kV/µs is unsurpassed. Performance
is specified over the temperature range of −40°C to +85°C without
derating.
IL260-Series Isolators are available in 0.3" and 0.15" 16-pin SOIC
packages. In the 0.15" packages, the five-channel devices provide the
highest channel density available.
IL260/IL261/IL262
2
Absolute Maximum Ratings
Parameters Symbol Min. Typ. Max. Units Test Conditions
Storage Temperature TS −55 150 °C
Ambient Operating Temperature
(
1
)
T
A −55 125 °C
Supply Voltage VDD1 ,VDD2 −0.5 7 V
Input Voltage VI −0.5 VDD + 0.5 V
Output Voltage VO −0.5 VDD + 0.5 V
Output Current Drive IO −10 10 mA
Lead Solder Temperature 260 °C 10 sec.
ESD 2 kV HBM
Recommended Operating Conditions
Parameters Symbol Min. Typ. Max. Units Test Conditions
Ambient Operating Temperature T
A −40 85 °C
Supply Voltage VDD1 ,VDD2 3.0 5.5 V 3.3/5.0 V Operation
Logic High Input Voltage VIH 2.4 VDD V
Logic Low Input Voltage VIL 0 0.8 V
Input Signal Rise and Fall Times tIR, tIF 1 μs
Insulation Specifications
Parameters Symbol Min. Typ. Max. Units Test Conditions
Creepage Distance (external)
0.15'' SOIC 4.03 mm
0.3'' SOIC 8.08 mm
Leakage Current
(
5
)
0.2 μARMS 240 VRMS
Barrier Impedance
(
5
)
>1014||7 Ω || pF
Capacitance (Input–Output)
(
5
)
C
I–O 5 pF f = 1 MHz
Safety and Approvals
IEC61010-2001
TUV Certificate Numbers: N1502812, N1502812-101
Classification as Reinfor ced Insulation
Model Package Pollution Degree Material Group
Max. Working
Voltage
IL260, IL261, IL262 0.3'' 16-pin SOIC II III 300 VRMS
IL260-3, IL261-3, IL262-3 0.15'' 16-pin SOIC II III 150 VRMS
UL 1577
Component Recognition Program File Number: E207481
Rated 2500 VRMS for 1 minute (SOIC, PDIP)
Soldering Profile
Per JEDEC J-STD-020C, MSL=2
IL260/IL261/IL262
3
IL260 Pin Connections
1 IN1 Input 1
2 GND1 Ground*
3 IN2 Input 2
4 IN3 Input 3
5 IN4 Input 4
6 VDD1 Supply Voltage 1
7 IN5 Input 5
8 GND1 Ground*
9 GND2 Ground*
10 OUT5 Output 5
11 OUT4 Output 4
12 OUT3 Output 3
13 OUT2 Output 2
14 OUT1 Output 1
15 GND2 Ground*
16 VDD2 Supply Voltage 2
IN
1
V
DD2
GND
1
GND
2
IN
2
OUT
1
IN
3
OUT
2
IN
4
OUT
3
V
DD1
IN
5
OUT
4
OUT
5
GND
1
GND
2
IL260
IL261 Pin Connections
1 VDD1 Supply Voltage 1
2 GND1 Ground*
3 IN1 Input 1
4 IN2 Input 2
5 IN3 Input 3
6 IN4 Input 4
7 OUT5 Output 5
8 GND1 Ground*
9 GND2 Ground*
10 IN5 Input 5
11 OUT4 Output 4
12 OUT3 Output 3
13 OUT2 Output 2
14 OUT1 Output 1
15 GND2 Ground*
16 VDD2 Supply Voltage 2
V
DD1
V
DD2
GND
1
GND
2
IN
1
OUT
1
IN
2
OUT
2
IN
3
OUT
3
IN
4
OUT
5
OUT
4
IN
5
GND
1
GND
2
IL261
IL262 Pin Connections
1 VDD1 Supply Voltage 1
2 GND1 Ground*
3 IN1 Input 1
4 IN2 Input 2
5 IN3 Input 3
6 OUT4 Output 4
7 OUT5 Output 5
8 GND1 Ground*
9 GND2 Ground*
10 IN5 Input 5
11 IN4 Input 4
12 OUT3 Output 3
13 OUT2 Output 2
14 OUT1 Output 1
15 GND2 Ground*
16 VDD2 Supply Voltage 2
V
DD1
V
DD2
GND
1
GND
2
IN
1
OUT
1
IN
2
OUT
2
IN
3
OUT
3
OUT
4
OUT
5
IN
4
IN
5
GND
1
GND
2
IL262
*NOTE: Pins 2 and 8 are internally connected, as are pins 9 and 15.
IL260/IL261/IL262
4
3.3 Volt Electrical Specifications (Tmin to Tmax)
Parameters Symbol Min. Typ. Max. Units Test Conditions
Input Quiescent Current IL260
IL261
IL262 IDD1
300
1.5
3
400
2
4
μA
mA
mA
Output Quiescent Current IL260
IL261
IL262 IDD2 6.5
5
3.5
10
8
6
mA
mA
mA
Logic Input Current Ii −10 10 μA
Logic High Output Voltage VOH VDD−0.1 VDD V IO = −20 μA, VI=VIH
0.8 x VDD 0.9 x VDD I
O = −4 mA, VI=VIH
Logic Low Output Voltage VOL 0 0.1
V IO = 20 μA, VI=VIL
0.5 0.8 IO = 4 mA, VI=VIL
Switching Specifications
Maximum Data Rate 100 110 Mbps CL = 15 pF
Minimum Pulse Width
(
7
)
PW 10 ns 50% Points, VO
Propagation Delay Input to Output
(High to Low) tPHL 12 18 ns CL = 15 pF
Propagation Delay Input to Output
(Low to High) tPLH 12 18 ns CL = 15 pF
Pulse Width Distortion |tPHL−tPLH|
(
2
)
PWD 2 3 ns CL = 15 pF
Propagation Delay Skew
(
3
)
t
PS
K
4 6 ns CL = 15 pF
Output Rise Time (10%–90%) tR 2 4 ns CL = 15 pF
Output Fall Time (10%–90%) tF 2 4 ns CL = 15 pF
Common Mode Transient Immunity
(Output Logic High to Logic Low)(4) |CMH|,|CML| 20 30 kV/μs VCN = 300 V
Channel-to-Channel Skew 2 3 ns CL = 15 pF
Dynamic Power Consumption
(
6
)
140 240 μA/MHz per channel
Magnetic Field Immunity(8) (VDD2= 3V, 3V<VDD1<5.5V)
Power Frequency Magnetic Immunity HPF 1000 1500 A/m 50Hz/60Hz
Pulse Magnetic Field Immunity HPM 1800 2000 A/m t
p
= 8µs
Damped Oscillatory Magnetic Field HOSC 1800 2000 A/m 0.1Hz – 1MHz
Cross-axis Immunity Multiplier
(
9
)
K
X 2.5
IL260/IL261/IL262
5
5 Volt Electrical Specifications (Tmin to Tmax)
Parameters Symbol Min. Typ. Max. Units Test Conditions
Input Quiescent Current IL260
IL261
IL262 IDD1
350
2
4
500
3
6
μA
mA
mA
Output Quiescent Current IL260
IL261
IL262 IDD2 10
7.5
5
15
12
9
mA
mA
mA
Logic Input Current Ii −10 10 μA
Logic High Output Voltage VOH VDD−0.1 VDD V IO = −20 μA, VI = VIH
0.8 x VDD 0.9 x VDD I
O = −4 mA, VI = VIH
Logic Low Output Voltage VOL 0 0.1
V IO = 20 μA, VI = VIL
0.5 0.8 IO = 4 mA, VI = VIL
Switching Specifications
Maximum Data Rate 100 110 Mbps CL = 15 pF
Minimum Pulse Width
(
7
)
PW 10 ns 50% Points, VO
Propagation Delay Input to Output
(High to Low) tPHL 10 15 ns CL = 15 pF
Propagation Delay Input to Output
(Low to High) tPLH 10 15 ns CL = 15 pF
Pulse Width Distortion |tPHL−tPLH|
(
2
)
PWD 2 3 ns CL = 15 pF
Pulse Jitter
(
10
)
t
J 100 ps CL = 15 pF
Propagation Delay Skew
(
3
)
t
PS
K
4 6 ns CL = 15 pF
Output Rise Time (10%–90%) tR 1 3 ns CL = 15 pF
Output Fall Time (10%–90%) tF 1 3 ns CL = 15 pF
Common Mode Transient Immunity
(Output Logic High to Logic Low)(4) |CMH|,|CML| 20 30 kV/μs VCN = 300 V
Channel-to-Channel Skew 2 3 ns CL = 15 pF
Dynamic Power Consumption
(
6
)
200 340 μA/MHz per channel
Magnetic Field Immunity(8) (VDD2= 5V, 3V<VDD1<5.5V)
Power Frequency Magnetic Immunity HPF 2800 3500 A/m 50Hz/60Hz
Pulse Magnetic Field Immunity HPM 4000 4500 A/m t
p
= 8µs
Damped Oscillatory Magnetic Field HOSC 4000 4500 A/m 0.1Hz – 1MHz
Cross-axis Immunity Multiplier
(
9
)
K
X 2.5
Notes (apply to both 3.3 V and 5 V specifications):
1. Absolute maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does not
guarantee performance.
2. PWD is defined as |tPHL − tPLH|. %PWD is equal to PWD divided by pulse width.
3. tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH between devices at 25°C.
4. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum
common mode input voltage that can be sustained while maintaining VO < 0.8 V. The common mode voltage slew rates apply to both rising
and falling common mode voltage edges.
5. Device is considered a two terminal device: pins 1–8 shorted and pins 9–16 shorted.
6. Dynamic power consumption numbers are calculated per channel and are supplied by the channel’s input side power supply.
7. Minimum pulse width is the minimum value at which specified PWD is guaranteed.
8. The relevant test and measurement methods are given in the Electromagnetic Compatibility section on p. 6.
9. External magnetic field immunity is improved by this factor if the field direction is “end-to-end” rather than to “pin-to-pin” (s ee diagram on p. 6).
10. 66,535-bit pseudo-random binary signal (PRBS) NRZ bit pattern with no more than five consecutive 1s or 0s; 800 ps transition time.
IL260/IL261/IL262
6
80 ns
Application Information
Electrostatic Discharge Sensitivity
This product has been tested for electrostatic sensitivity to the
limits stated in the specifications. However, NVE recommends that
all integrated circuits be handled with appropriate care to avoid
damage. Damage caused by inappropriate handling or storage could
range from performance degradation to complete failure.
Electromagnetic Compatibility
IsoLoop Isolators have the lowest EMC footprint of any isolation
technology. IsoLoop Isolators’ Wheatstone bridge configuration
and differential magnetic field signaling ensure excellent EMC
performance against all relevant standards.
These isolators are fully compliant with generic EMC standards
EN50081, EN50082-1 and the umbrella line-voltage standard for
Information Technology Equipment (ITE) EN61000. NVE has
completed compliance tests in the categories below:
EN50081-1
Residential, Commercial & Light Industrial
Methods EN55022, EN55014
EN50082-2: Industrial Environment
Methods EN61000-4-2 (ESD), EN61000-4-3 (Electromagnetic
Field Immunity), EN61000-4-4 (Electrical Transient Immunity),
EN61000-4-6 (RFI Immunity), EN61000-4-8 (Power Frequency
Magnetic Field Immunity), EN61000-4-9 (Pulsed Magnetic
Field), EN61000-4-10 (Damped Oscillatory Magnetic Field)
ENV50204
Radiated Field from Digital Telephones (Immunity Test)
Immunity to external magnetic fields is even higher if the field
direction is “end-to-end” rather than to “pin-to-pin” as shown in the
diagram below: Cross-axis Field Direction
Dynamic Power Consumption
IsoLoop Isolators achieve their low power consumption from the
way they transmit data across the isolation barrier. By detecting the
edge transitions of the input logic signal and converting these to
narrow current pulses, a magnetic field is created around the GMR
Wheatstone bridge. Depending on the direction of the magnetic
field, the bridge causes the output comparator to switch following
the input logic signal. Since the current pulses are narrow, about
2.5 ns, the power consumption is independent of mark-to-space
ratio and solely dependent on frequency. This has obvious
advantages over optocouplers, which have power consumption
heavily dependent on mark-to-space ratio.
Power Supply Decoupling
Both power supplies to these devices should be decoupled with low
ESR 47 nF ceramic capacitors. Ground planes for both GND1 and
GND2 are highly recommended for data rates above 10 Mbps.
Capacitors must be located as close as possible to the VDD pins.
Signal Status on Start-up and Shut Down
To minimize power dissipation, input signals are differentiated and
then latched on the output side of the isolation barrier to reconstruct
the signal. This could result in an ambiguous output state
depending on power up, shutdown and power loss sequencing.
Therefore, the designer should consider including an initialization
signal in the start-up circuit. Initialization consists of toggling the
input either high then low, or low then high.
Data Transmission Rates
The reliability of a transmission system is directly related to the
accuracy and quality of the transmitted digital information. For a
digital system, those parameters which determine the limits of the
data transmission are pulse width distortion and propagation delay
skew.
Propagation delay is the time taken for the signal to travel through
the device. This is usually different when sending a low-to-high
than when sending a high-to-low signal. This difference, or error, is
called pulse width distortion (PWD) and is usually in nanoseconds.
It may also be expressed as a percentage:
PWD% = Maximum Pulse Width Distortion (ns) x 100%
Signal Pulse Width (ns)
For example, with data rates of 12.5 Mbps:
PWD% = 3 ns x 100% = 3.75%
This figure is almost three times better than an y available
optocoupler with the same temperature range, and two times better
than any optocoupler regardless of published temperature range.
IsoLoop isolators exceed the 10% maximum PWD recommended
by PROFIBUS, and will run to nearly 35 Mb within the 10% limit.
Propagation delay skew is the signal propagation difference
between two or more channels. This becomes significant in clocked
systems because it is undesirable for the clock pulse to arrive
before the data has settled. Short propagation delay skew is
therefore especially critical in high data rate parallel systems for
establishing and maintaining accuracy and repeatability. Worst-
case channel-to-channel skew in IL260-Series Isolators is only
3 ns, which is ten times better than any optocoupler. IL260-Series
Isolators have a maximum propagation delay skew of 6 ns, which is
five times better than any optocoupler.
IL260/IL261/IL262
7
Application Diagram—Multi-Channel Delta-Sigma A/D Converter
In a typical single-channel delta-sigma ADC, the system clock is located on the isolated side of the system and only four channels of isolation are
required. With multiple ADCs configured in a channel-to-channel isolation configuration, however, clock jitter and edge placement accurac y of
the system clock must be matched between ADCs. The best solution is to use a single clock on the system side and distribute the clock to each
ADC. The five-channel IL261 is ideal, with the fifth channel used to distribute a single, isolated clock to multiple ADCs as shown below:
Bridge +
Serial Data Out
Serial Data In
Data Clock
Chip Select
Iso SD Out
Iso SD In
Iso Data Clock
Iso CS
Bridge -
OSC 2
IL261
CS5532
Clock
Generator
Bridge
Bias
Delta Sigma A/D
Isolation
Boundary
Bridge +
Serial Data Out
Serial Data In
Data Clock
Chip Select
Iso SD Out
Iso SD In
Iso Data Clock
Iso CS
Bridge -
OSC 2
IL261
CS5532
Bridge
Bias
Delta Sigma A/D
Channel 1
Channel n
IL260/IL261/IL262
8
Package Drawings, Dimensions and Specifications
0.15" 16-pin SOIC Package
0.054 (1.4)
0.072 (1.8)
0.040 (1.0)
0.060 (1.5)
0.016 (0.4)
0.050 (1.3)
0.386 (9.8)
0.394 (10.0)
Pin 1 identified
by either an
indent or a
marked dot
NOM
0.228 (5.8)
0.244 (6.2)
0.152 (3.86)
0.157 (3.99)
Dimensions in inches (mm)
0.007 (0.2)
0.013 (0.3)
0.004 (0.1)
0.012 (0.3)
0.040 (1.02)
0.050 (1.27)
0.013 (0.3)
0.020 (0.5)
Pin spacing is a BASIC
dimension; tolerances
do not accumulate
NOTE:
0.3" 16-pin SOIC Package
NOM
Pin 1 identified by
either an indent
or a marked dot
0.287 (7.29)
0.300 (7.62)
Dimensions in inches (mm)
0.08 (2.0)
0.10 (2.5)
0.092 (2.34)
0.105 (2.67)
0.397 (10.1)
0.413 (10.5)
0.013 (0.3)
0.020 (0.5)
0.394 (10.00)
0.419 (10.64)
0.040 (1.0)
0.060 (1.5) 0.004 (0.1)
0.012 (0.3)
0.007 (0.2)
0.013 (0.3) 0.016 (0.4)
0.050 (1.3)
Pin spacing is a BASIC
dimension; tolerances
do not accumulate
NOTE:
IL260/IL261/IL262
9
Ordering Information and Valid Part Numbers
IL 260 - 3 E TR13
Bulk Package
Blank = Tube
TR7 = 7'' Tape and Reel
TR13 = 13'' Tape and Reel
Package
Blank = 80/20 Tin/Lead Plating
E = RoHS Compliant
Package T ype
Blank = 0.3" 16-pin SOIC
-3 = 0.15'' 16-pin SOIC
Base Part Number
260 = 5 Drive Channels
261 = 4 Drive Channels,
1 Receive Channel
262 = 3 Drive Channels,
2 Receive Channel
Product Family
IL = Isolators
Valid Part Numbers
IL260
IL260E
IL260-3
IL260-3E
IL261
IL261E
IL261-3
IL261-3E
IL262
IL262E
IL262-3
IL262-3E
All IL260-Series part
types are available on
tape and reel.
RoHS
COMPLIANT
IL260/IL261/IL262
10
Revision History
ISB-DS-001-IL260/1-M
March 2012
Change
• Tightened typ. output quiescent supply specs.
ISB-DS-001-IL260/1/2-L
Change
• Update terms and conditions.
ISB-DS-001-IL260/1/2-K
Change
• Added clarification of internal ground connections.
ISB-DS-001-IL260/1/2-J
Change
• Relaxed Vdd1 quiescent current specification to 500µA.
ISB-DS-001-IL260/1/2-I
Change
• Added typical jitter specification at 5V.
ISB-DS-001-IL260/1/2-H
Change
• Added EMC details.
ISB-DS-001-IL260/1/2-G
Change
• Added magnetic field immunity and electromagnetic compatibility
specifications.
ISB-DS-001-IL260/1/2-F
Change
• Added IL262 c on fi g urat i o n
• Added note on packa ge drawings that pin-s p aci ng tol erances are non-
accumulating.
• Changed ordering information to reflect that devices are fully RoHS
compliant with no exemptions.
ISB-DS-001-IL260/1-E
Change
• Eliminated soldering profile chart
ISB-DS-001-IL260/1-D
Change
• Revised application drawing
• Revised package drawings
• Misc. syntax changes
IL260/IL261/IL262
11
Datasheet Limitations
The information and data provided in datasheets shall define the specification of the product as agreed between NVE and its customer, unless NVE and
customer have explicitly agreed otherwise in writing. All specifications are based on NVE test protocols. In no event however, shall an agreement be
valid in which the NVE product is deemed to offer functions and qualities beyond those described in the datasheet.
Limited Warranty and Liability
Information in this document is believed to be accurate and reliable. However, NVE does not give any representations or warranties, expressed or
implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information.
In no event shall NVE be liable for any indirect, incidental, punitive, special or consequential damages (including, without limitation, lost profits, lost
savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on
tort (including negligence), warranty, breach of contract or any other legal theory.
Right to Make Changes
NVE reserves the right to make changes to information published in this document including, without limitation, specifications and product descriptions
at any time and without notice. This document supersedes and replaces all information supplied prior to its publication.
Use in Life-Critical or Safety-Critical Applications
Unless NVE and a customer explicitly agree otherwise in writing, NVE products are not designed, authorized or warranted to be suitable for use in life
support, life-critical or safety-critical devices or equipment. NVE accepts no liability for inclusion or use of NVE products in such applications and such
inclusion or use is at the customer’s own risk. Should the customer use NVE products for such application whether authorized by NVE or not, the
customer shall indemnify and hold NVE harmless against all claims and damages.
Applications
Applications described in this datasheet are illustrative only. NVE makes no representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications and products using NVE products, and NVE accepts no liability for any
assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NVE product is suitable and fit for
the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customers. Customers should
provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.
NVE does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s
applications or products, or the application or use by customer’s third party customers. The customer is responsible for all necessary testing for the
customer’s applications and products using NVE products in order to avoid a default of the applications and the products or of the application or use by
customer’s third party customers. NVE accepts no liability in this respect.
Limiting Values
Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the
device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the recommended
operating conditions of the datasheet is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the
quality and reliability of the device.
Terms and Conditions of Sale
In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NVE hereby expressly objects to
applying the customer’s general terms and conditions with regard to the purchase of NVE products by customer.
No Offer to Sell or License
Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication
of any license under any copyrights, patents or other industrial or intellectual property rights.
Export Control
This document as well as the items described herein may be subject to export control regulations. Export might require a prior authorization from national
authorities.
Automotive Qualified Products
Unless the datasheet expressly states that a specific NVE product is automotive qualified, the product is not suitable for automotive use. It is neither
qualified nor tested in accordance with automotive testing or application requirements. NVE accepts no liability for inclusion or use of non-automotive
qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall
use the product without NVE’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the
product for automotive applications beyond NVE’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies
NVE for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NVE’s
standard warranty and NVE’s product specifications.
IL260/IL261/IL262
12
An ISO 9001 Certified Company
NVE Corporation
11409 Valley View Road
Eden Prairie, MN 55344-3617 USA
Telephone: (952) 829-9217
Fax: (952) 829-9189
www.nve.com
e-mail: iso-info@nve.com
©NVE Corporation
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
ISB-DS-001-IL260/1/2-M March 2012
