Previous Datasheet Index Next Data Sheet PD 1.031A Series PVU414 Microelectronic Power IC Relay Single Pole, Normally Open HEXFET POWER MOSFET PHOTOVOLTAIC RELAY 0-400V, 140mA AC/DC PVU414 Features General Description The PVU414 Series Photovoltaic Relay is a single-pole, normally open solid-state relay that can replace electromechanical relays in many applications. It utilizes International Rectifier's proprietary HEXFET power MOSFET as the output switch, driven by an integrated circuit photovoltaic generator of novel construction. The output switch is controlled by radiation from a GaAlAs light emitting diode (LED) which is optically isolated from the photovoltaic generator. HEXFET output Bounce-free operation High operating speed High off-state resistance 0.2 V thermal offset voltage Linear AC/DC operation 4,000 VRMS I/O isolation Solid-state reliability UL and CSA certifications pending The PVU414 is ideally suited for instrumentation, multiplexing, scanning and data acquisition applications. It offers high operating speed, low thermal offset (EMF) voltage, low and stable on-state resistance and high off-state resistance. The PVU414 relay is packaged in a 6-pin, molded DIP package with either thru-hole or "gull-wing" surface mount terminals. It is available in standard plastic shipping tubes or on tape-and-reel. Refer to Part Identification information. Part Identification Applications Multiplexing Scanning Multichannel Sampling Data Acquisition Signal Level Switching Instrumentation and Measurement PVU414 PVU414S PVU414S-T thru-hole SMT SMT, T&R (HEXFET is the registered trademark for International Rectifier's power MOSFETs) To Order Previous Datasheet Index Next Data Sheet Series PVU414 Electrical Specifications (-40C TA +85C unless otherwise specified) INPUT CHARACTERISTICS Limits Units Min. Control Current (See Fig. 1) Max. Control Current for Off-State Resistance @T A=+25C Control Current Range (Caution: current limit input LED, See Fig.6) 3.0 0.4 3.0 to 25 mA mA mA 7.0 V Max. Reverse Voltage OUTPUT CHARACTERISTICS Operating Voltage Range Max. Load Current @T A=+40C 5mA Control (See Fig. 1) Max. On-State Resistance @T A=+25C For 50mA Pulsed Load, 5mA Control (See Fig.5) Limits Units 0 to 400 V(DC or AC peak) `A' Connection `B' Connection `C' Connection 140 150 210 mA (AC or DC) mA (DC) mA (DC) `A' Connection `B' Connection `C' Connection 27 14 7 1010 500 s 200 0.2 12 s V pF Min. Off-State Resistance @T A=+25C, 320V (See Fig. 5) Max. Turn-On Time @T A=+25C (See Fig. 7) For 50mA, 100 VDC Load, 5mA Control Max. Turn-Off Time @T A=+25C (See Fig. 7) For 50mA, 100 VDC Load, 5mA Control Max. Thermal Offset Voltage @ 5mA Control Max. Output Capacitance @ 50V DC (See Fig. 2) GENERAL CHARACTERISTICS Limits Units Min. Dielectric Strength, Input-Output 4000 V RMS Min. Insulation Resistance, Input-Output @T A=+25C, 50%RH, 100V DC 1012 Max. Capacitance, Input-Output 1.0 pF +260 -40 to +85 -40 to +100 C C C Max. Pin Soldering Temperature (10 seconds max.) Ambient Temperature Range: Operating Storage Connection Diagrams To Order Previous Datasheet Index Next Data Sheet Series PVU414 I LED ILED = = 55mA mA "A""A" Connection Connection "A" "A"Connection Connection Max. Load Current (mA) Typical Capacitance (pF) mA ILED = 33mA Ambient Temperature (deg. C) Vdd, Drain to Drain Voltage (V) Figure 2. Typical Output Capacitance Figure 1. Current Derating Curves "A" Connection 5 mA Control ID = 10 mA Rd-on (Normalized to 25 deg. C) Load Current (mA) "A" Connection 5 mA Control @25C pulsed Connection `A' Voltage Drop (Vdd) Ambient Temperature (deg. C) Figure 4. Typical Normalized On-Resistance Input Current (mA) ID-OFF / I D-OFF 25 deg. C Figure 3. Linearity Characteristics Ambient Temperature (deg. C) LED Forward Voltage Drop (Volts DC) Figure 5. Typical Normalized Off-State Leakage Figure 6. Input Characteristics (Current Controlled) To Order Previous Datasheet Index Next Data Sheet Series PVU414 Mechanical Specifications Delay Time (microseconds) (Dimensions in millimeters (inches)) LED Current (mA) Figure 7. Typical Delay Times 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 2. CONTROLLING DIMENSION: INCH DIMENSION DOES NOT INCLUDE MOLD PROTRUSIONS. MOLD PROTRUSIONS SHALL NOT EXCEED 0.25 (.010). Figure 8. Delay Time Definitions WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 322 3331 EUROPEAN HEADQUARTERS: Hurst Green, Oxted, Surrey RH8 9BB, UK Tel: ++ 44 1883 732020 IR CANADA: 7321 Victoria Park Ave., Suite 201, Markham, Ontario L3R 2Z8, Tel: (905) 475 1897 IR GERMANY: Saalburgstrasse 157, 61350 Bad Homburg Tel: ++ 49 6172 96590 IR ITALY: Via Liguria 49, 10071 Borgaro, Torino Tel: ++ 39 11 451 0111 IR FAR EAST: K&H Bldg., 2F, 3-30-4 Nishi-Ikeburo 3-Chome, Toshima-Ki, Tokyo Japan 171 Tel: 81 3 3983 0086 IR SOUTHEAST ASIA: 315 Outram Road, #10-02 Tan Boon Liat Building, Singapore 0316 Tel: 65 221 8371 http://www.irf.com/ Data and specifications subject to change without notice. 8/96 To Order