1-124
H
Features
• High Light Output over a
Wide Range of Currents
(500 µA to 50 mA)
• Popular T-1 Package
• Low Forward Voltage
• Low Power Dissipation
• Deep Red Color
• Long Life: Solid State
Reliability
• Wide Viewing Angles
• Available on Tape and Reel
Applications
• Outdoor Message Boards
• Automotive Lighting
• Portable Equipment
• Safety Lighting Equipment
• Medical Equipment
• Changeable Message Signs
Package Dimensions
T-1 (3 mm) High Performance
TS AlGaAs Red LED Lamps
Technical Data
3.18 (0.125)
2.67 (0.105)
25.40 (1.00)
MIN.
1.27 (0.050)
NOM.
1.02 (0.040)
NOM.
6.35 (0.250)
5.58 (0.220)
0.45 (0.018)
SQUARE
NOMINAL
CATHODE
2.54 (0.100)
NOM.
4.70 (0.185)
4.19 (0.165)
3.43 (0.135)
2.92 (0.115)
ANODE
HLMP-J100
HLMP-J105
HLMP-J150
HLMP-J155
5964-9372E
Description
The T-1 solid state lamps utilize a
highly optimized LED material
technology, transparent substrate
aluminum gallium arsenide (TS
AlGaAs). This LED technology
has a very high luminous
efficiency, capable of producing
high light output over a wide
range of drive currents (500 µA to
50 mA). The color is deep red at a
dominant wavelength of 644 nm.
TS AlGaAs is a flip-chip LED
technology, die attached to the
anode lead and wire bonded to
the cathode lead.
Device Selection Guide
Viewing Typical Typical
Angle Deep Red IV (mcd) IV (mcd)
Package Description 2θ1/2λd = 644 nm IF = 20 mA IF = 0.5 mA
T-1 (3 mm), Untinted, 45°HLMP-J105 340 –
Non-diffused, Standard Current
T-1 (3 mm), Untinted, 45°HLMP-J155 – 6
Non-diffused, Low Current
T-1 (3 mm), Tinted, Diffused, 55°HLMP-J100 175 –
Standard Current
T-1, (3 mm), Tinted, Diffused, 55°HLMP-J150 – 3
Low Current
1-125
Absolute Maximum Ratings
Peak Forward Current[2] ............................................................ 300 mA
Average Forward Current (@ IPEAK = 300 mA)[1,2] ...................... 30 mA
DC Forward Current[3] ................................................................. 50 mA
Power Dissipation ..................................................................... 100 mW
Reverse Voltage (IR = 100 µA) ......................................................... 5 V
Transient Forward Current (10 µs Pulse)[4] ............................... 500 mA
Operating Temperature Range........................................ -55 to +100°C
Storage Temperature Range ........................................... -55 to +100°C
LED Junction Temperature...........................................................110°C
Solder Temperature ................................................260°C for 5 seconds
[1.6 mm (0.063 in.) from body]
Notes:
1. Maximum IAVG at f = 1 kHz, DF = 10%.
2. Refer to Figure 6 to establish pulsed operating conditions.
3. Derate linearly as shown in Figure 5.
4. The transient peak current is the maximum non-recurring peak current the device can
withstand without damaging the LED die and wire bonds. It is not recommended that
the device be operated at peak currents above the Absolute Maximum Peak Forward
Current.
Optical Characteristics at TA = 25°C
Luminous Color, Viewing
Part Intensity Total Flux Peak ZDominant Angle Luminous
Number IV (mcd) φv (mlm) Wavelength Wavelength 2θ1/2Efficacy
(Low @ 0.5 mA[1] @ 0.5 mA[2] λPEAK (nm) λd[3] (nm) (Degrees)[4] ηv
Current) Min. Typ. Typ. Typ. Typ. Typ. (lm/w)
HLMP-J155 2.1 6.0 37.2 654 644 45 85
HLMP-J150 1.3 3.0 654 644 55 85
Notes:
1. The luminous intensity, IV, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern
may not be aligned with this axis.
2. φV is total luminous flux output as measured with an integrating sphere.
3. The dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the color of the device.
4. θ1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity.
Optical Characteristics at TA = 25°C
Luminous Color, Viewing
Intensity Total Flux Peak Dominant Angle Luminous
IV (mcd) φv (mlm) Wavelength Wavelength 2θ1/2Efficacy
Part @ 20 mA[1] @ 20 mA[2] λPEAK (nm) λd[3] (nm) (Degrees)[4] ηv
Number Min. Typ. Typ. Typ. Typ. Typ. (lm/w)
HLMP-J105 56.4 340 280 654 644 45 85
HLMP-J100 35.2 175 654 644 55 85
1-126
Electrical Characteristics at TA = 25°C
Speed of
Forward Reverse Capacitance Response
Voltage Breakdown C (pF) τs (ns)
VF (Volts) VR (Volts) VF = 0, Thermal Time Constant
Part @ IF = 20 mA @ IR = 100 µA f = 1 MHz Resistance e-t/τ
Number Typ. Max. Min. Typ. Typ. RθJ-PIN (°C/W) Typ.
HLMP-J105 1.9 2.4 5 20 20 290 45
HLMP-J100 1.9 2.4 5 20 20 290 45
RELATIVE INTENSITY
600 1000
10
-3
WAVELENGTH – nm
700500
10
-2
10
-1
1.0
IF – FORWARD CURRENT – mA
1.0 3.5
300
20
1
VF – FORWARD VOLTAGE – V
1.5 2.0 2.5 3.0
200
100
50
10
5
2
0.50
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 20 mA)
2
0.5
0.01
I
F
– DC FORWARD CURRENT – mA
51020 50
2.4
2.0
1.0
0.2
0.1
0.05
10.5
Figure 1. Relative Intensity vs.
Wavelength. Figure 2. Forward Current vs.
Forward Voltage. Figure 3. Relative Luminous Intensity
vs. DC Forward Current.
s
Electrical Characteristics at TA = 25°C
Speed of
Forward Reverse Capacitance Response
Part Voltage Breakdown C (pF) τs (ns)
Number VF (Volts) VR (Volts) VF = 0, Thermal Time Constant
(Low @ IF = 0.5 mA @ IR = 100 µA f = 1 MHz Resistance e-t/τ
Current) Typ. Max. Min. Typ. Typ. RθJ-PIN (°C/W) Typ.
HLMP-J155 1.6 1.9 5 20 20 290 45
HLMP-J150 1.6 1.9 5 20 20 290 45
s
1-127
Figure 5. Maximum Forward DC
Current vs. Ambient Temperature.
Derating Based on TJMAX = 110
Figure 4. Relative Efficiency vs. Peak
Forward Current.
Figure 6. Maximum Average Current
vs. Peak Forward Current.
η
V
– RELATIVE EFFICIENCY
(NORMALIZED AT 20 mA)
5 300
0.0
I
PEAK
– PEAK FORWARD CURRENT – mA
10 20 50 100
21 200
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
I
F
– FORWARD CURRENT – mA
0
0
T
A
– AMBIENT TEMPERATURE – °C
40 80
50
40
30
20
10
20 60 100
Rθ
JA
= 400° C/W
Rθ
JA
= 550° C/W
I
AVG
= AVERAGE FORWARD CURRENT – mA
50
0
I
PEAK
– PEAK FORWARD CURRENT – mA
150 250
50
40
30
20
10
100 200 300
f > 1000 Hz
f > 300 Hz
f > 100 Hz
NORMALIZED INTENSITY
1.0
0
ANGULAR DISPLACEMENT – DEGREES
0.8
0.6
0.5
0.7
0.2
100 90
0.1
0.3
0.4
80 70 60 50 40 20 10 030 10 20 30 40 50 60 70 80 90 100
0.9
Figure 8. Normalized Luminous Intensity vs. Angular
Displacement. HLMP-J100/J150.
NORMALIZED INTENSITY
1.0
0
θ – ANGULAR DISPLACEMENT – DEGREES
0.8
0.6
0.5
0.7
0.2
100 90
0.1
0.3
0.4
80 70 60 50 40 20 10 030 10 20 30 40 50 60 70 80 90 100
0.9
Figure 7. Normalized Luminous Intensity vs. Angular
Displacement. HLMP-J105/J155.
°C.
