EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E Photomicrosensor with 80-mA Switching Capacity that can be Built into Equipment Built-in amplifier Models available with 5- to 12-VDC and 5- to 15-VDC input CMOS- and TTL-compatible Model with easy adjustment with an external sensitivity adjuster (EE-SB5V) Special connectors (EE-1001/1006) are available 19-mm sensing distance (EE-SB5V-E) Convert to PNP output with EE-2002 conversion connector Ordering Information Appearance Sensing method Sensing distance Output configuration Weight Part number Reflective 5 mm Light-ON Approx. 3.0 g EE-SB5M Dark-ON EE-SB5MC Light-ON EE-SB5V Dark-ON 19 mm Light-ON EE-SB5VC Approx. 2.8 g EE-SB5V-E Specifications RATINGS Item Reflective EE-SB5M EE-SB5MC EE-SB5V(-E) EE-SB5VC Supply voltage 5 to 12 VDC 10%, ripple (p-p): 10% max. 5 to 15 VDC 10%, ripple (p-p): 10% max. Current consumption 36 mA max. 48 mA max. (DC current: IF = 25 mA) Maximum forward direct current (IF) -- 30 mA max. Forward voltage (VF) -- 1.5 V max. (IF = 30 mA) Reverse voltage (VR) -- 4 V max. Standard reference object White paper with reflection factor of 90% (standard sensing object: 15 x 15 mm) Differential distance 0.1 mm (This table continues on the next page.) EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E Specifications Table -- continued from previous page Reflective Item EE-SB5M Control output Output configuration EE-SB5MC EE-SB5V(-E) EE-SB5VC At 5 to 24 VDC: 80-mA load current (IC) with a residual voltage of 0.8 V max. When driving TTL: 40-mA load current (IC) with a residual voltage of 0.4 V max. Transistor on output stage OFF without detecting object ON OFF ON Transistor on output stage ON with detecting object OFF ON OFF Response frequency* 50 Hz Connecting method EE-1001/1006 Connectors; soldering terminals Light source GaAs infrared LED with a peak wavelength of 940 nm Receiver Si photo-transistor with a sensing wavelength of 850 nm max. *The response frequency was measured by detecting the following disks rotating. Disk 200 mm dia. 5 mm 15 mm 15 mm 15 mm CHARACTERISTICS Ambient temperature Ambient humidityy Operating -25C to 55C (-13F to 131F) Storage -30C to 80C (-22F to 176F) Operating 45% to 85% Storage 35% to 95% Vibration resistance Destruction: 20 to 2,000 Hz (with a peak acceleration of 20G's), 1.5-mm double amplitude for 4 min each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions Soldering heat resistance 2605C (See Note.) when the portion between the tip of the terminals and the position 1.5 mm from the terminal base is dipped into the solder for 101 seconds Note: This conforms to MIL-STD-750-2031-1. EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E Engineering Data OPERATING RANGE (TYPICAL 1) Releases Optical axis X Operates Y Releases Operates AREA (TYPICAL) X' (mm) SENSING DISTANCE VS. IF EE-SB5V-E (TYPICAL) EE-SB5M(C) 20 Reference object: White paper ( 15 x 15 mm) (reflection factor: 90%) Sensing Distance d (mm) Distance (mm) Optical axis X' Y X (mm) SENSING DISTANCE VS. OBJECT Reference object: White paper (15 x 15 mm) (reflection factor: 90%) EE-SB5M(C) Reference object: White paper ( 15 x 15 mm) (reflection factor: 90%) Distance Y (mm) Distance Y (mm) EE-SB5M(C) OPERATING RANGE (TYPICAL 2) TA = 25C Reference object White paper: (reflection factor 90%) 16 12 8 4 0 5 10 15 20 Forward Current IF (mA) Area (mm2) 25 30 EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E Operation INTERNAL/EXTERNAL CIRCUIT DIAGRAMS EE-SB5M(C) Light-ON/Dark-ON EE-SB5V(C), EE-SB5V-E Light-ON/Dark-ON 5 to 12 VDC L 5 to 15 VDC IC Logic circuit OUT Main circuit Connect RL as shown only when logic circuit is driven. OUT Main circuit Load (relay) RL Load (relay) Logic circuit L 0V Current-limiting resistor TIMING CHART Dark-ON Incident Interrupted Incident Interrupted Output transistor Load (relay) Output voltage (logic) ON ON Output transistor OFF Operates OFF Operates Load (relay) Releases H Output voltage (logic) L Releases H L Dimensions Unit: mm (inch) EE-SB5M(C), EE-SB5V(C), EE-SB5V-E 25.4 (1.00) 19.0 (0.75) 9.8 (0.39) 6.35 6.95 (0.25) 4.55 (0.18) (0.27) 13.0 (0.51) Optical axis 9.0 (0.35) Optical axis 16.7 (0.66) 13.2 8.0 (0.52) (0.31) 5.5 (0.22) 1.2 (0.05) 6.2 (0.24) 2.55 (0.10) Two, 3.2 dia. holes 0.6 (0.02) 1.5 Two, 3.8 dia. holes (1)(2)(3)(4) 0.8 (0.03) 2.54 (0.10) 1.45 (0.06) 0V RF LED display Light-ON RL IC 0.3 (0.01) Terminal Arrangement (1) VCC (2) L L (3) OUT OUTPUT (4) GND (0 V) EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E EE-SB5M(C)/SB5V(C)/SB5V-E + EE-1001 EE-SB5M(C)/SB5V(C)/SB5V + EE-1006 26 (1.02) 22.2 (0.87) 16.2 (0.64) 10.8 (0.48) 6.0 (0.24) EE-1001 CONNECTOR EE-1006 CONNECTOR WITH CABLE 13.0 (0.51) 2.540.15 4.0 (0.16) 0.6 (0.02) 10.8 (0.43) 0.6 (0.02) 6.0 (0.24) 16.2 (0.64) (1) (2) (3) (4) 11.8 (0.46) 2.91 2.54 (0.10) 2,000 (78.74) 20 (0.79) 5.3 (0.21) Terminal Arrangement (1) Red (Brown) (2) Yellow (Pink) (3) White (Black) (4) Black (Blue) L OUT VCC L OUTPUT GND (0 V) IEC colors are shown in parentheses. Note: Supply 5 to 12 V to the EE-SB5M(C). Wire as shown by the following diagram if the supply voltage exceeds 12 V. VCC (2) R VCC (1) Z VCC (2) = VCC (1) x Z Z+R GND Note: Z is the internal impedance between the positive and negative terminals. Model VCC (2) Z () EE-SB5M(C) 5 to 12 V 360 25 (0.98) 15 (0.59) EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E EE-SB5M/SB5MC/SB5V/SB5VC/SB5V-E Precautions Refer to the Technical Information Section for general precautions. Vcc L An external sensitivity adjuster can be connected to the EE-SB5V(C), EE-SB5V-E Photomicrosensor. When connecting the sensitivity adjuster, insert resistor RF (current-limiting resistor), as shown by the diagram. The value of RF is obtainable as follows: IF OUT RF External sensitivity adjuster 0V Output RF > (VCC - 1.5 V)/30 mA Note: The EE-SB5V(C) and EE-SB5V-E have no constant current circuit to protect the LED. For this reason, the LED will be damaged by excessive current applied to the positive terminal. To prevent potential LED damage, connect a current-limiting resistor, as shown previously. NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4. OMRON ELECTRONICS, INC. OMRON CANADA, INC. One East Commerce Drive Schaumburg, IL 60173 885 Milner Avenue Scarborough, Ontario M1B 5V8 1-800-55-OMRON 416-286-6465 Cat. No. EO5DAX4 1/99 Specifications subject to change without notice. Printed in U.S.A.