1
LTC1967
1967f
Precision Extended
Bandwidth, RMS-to-DC Converter
■
High Linearity:
0.02% Linearity Allows Simple System Calibration
■
Wide Input Bandwidth:
Bandwidth to 0.1% Additional Gain Error: 40kHz
Bandwidth Independent of Input Voltage Amplitude
■
No-Hassle Simplicity:
True RMS-DC Conversion with Only One External
Capacitor
Delta Sigma Conversion Technology
■
Low Supply Current:
330µA Typ
■
Ultralow Shutdown Current:
0.1µA
■
Flexible Inputs:
Differential or Single Ended
Rail-to-Rail Common Mode Voltage Range
Up to 1V
PEAK
Differential Voltage
■
Flexible Output:
Rail-to-Rail Output
Separate Output Reference Pin Allows Level Shifting
■
Small Size:
Space Saving 8-Pin MSOP Package
■
True RMS Digital Multimeters and Panel Meters
■
True RMS AC + DC Measurements
DESCRIPTIO
U
FEATURES
APPLICATIO S
U
The LTC
®
1967 is a true RMS-to-DC converter that uses an
innovative delta-sigma computational technique. The ben-
efits of the LTC1967 proprietary architecture when com-
pared to conventional log-antilog RMS-to-DC converters
are higher linearity and accuracy, bandwidth independent
of amplitude and improved temperature behavior.
The LTC1967 operates with single-ended or differential in-
put signals (for EMI/RFI rejection) and supports crest fac-
tors up to 4. Common mode input range is rail-to-rail. Dif-
ferential input range is 1V
PEAK
, and offers unprecedented
linearity. The LTC1967 allows hassle-free system calibra-
tion at any input voltage.
The LTC1967 has a rail-to-rail output with a separate out-
put reference pin providing flexible level shifting; it oper-
ates on a single power supply from 4.5V to 5.5V. A low power
shutdown mode reduces supply current to 0.1µA.
The LTC1967 is packaged in the space-saving MSOP pack-
age, which is ideal for portable applications.
Single Supply RMS-to-DC Converter
C
AVE
1µFV
OUT
+
–
1967 TA01
4.5V TO 5.5V
OUTPUT
DIFFERENTIAL
INPUT LTC1967
V
+
0.1µF
OPT. AC
COUPLING
EN GND
OUT RTN
IN1
IN2
TYPICAL APPLICATIO
U
V
IN
(mV AC
RMS
)
0
–1.0
LINEARITY ERROR (V
OUT
mV DC – V
IN
mV AC
RMS
)
–0.8
–0.6
–0.4
–0.2
0
0.2
100 200 300 400
1967 TA01b
500
LTC1967, ∆Σ
60Hz SINEWAVE
CONVENTIONAL
LOG/ANTILOG
Linearity Performance
, LTC and LT are registered trademarks of Linear Technology Corporation.
Protected under U.S. Patent Numbers 6,359,576, 6,362,677 and 6,516,291
2
LTC1967
1967f
Supply Voltage
V
+
to GND............................................................. 6V
Input Currents (Note 2) ..................................... ±10mA
Output Current (Note 3)..................................... ±10mA
ENABLE Voltage ......................................... –0.3V to 6V
OUT RTN Voltage........................................ –0.3V to V
+
Operating Temperature Range (Note 4)
LTC1967C/LTC1967I ......................... –40°C to 85°C
Specified Temperature Range (Note 5)
LTC1967C/LTC1967I ......................... –40°C to 85°C
Maximum Junction Temperature ......................... 150°C
Storage Temperature Range ................ –65°C to 150°C
Lead Temperature (Soldering, 10 sec)................. 300°C
ORDER PART
NUMBER
LTC1967CMS8
LTC1967IMS8
T
JMAX
= 150°C, θ
JA
= 220°C/W
ABSOLUTE AXI U RATI GS
WWWU
PACKAGE/ORDER I FOR ATIO
UU
W
(Note 1)
MS8 PART MARKING
LTTJ
The ● denotes specifications which apply over the full operating
temperature range, otherwise specifications are TA = 25°C. V+ = 5V, VOUTRTN = 2.5V, CAVE = 10µF, VIN = 200mVRMS, VENABLE = 0.5V
unless otherwise noted.
ELECTRICAL CHARACTERISTICS
Consult LTC Marketing for parts specified with wider operating temperature ranges.
1
2
3
4
GND
IN1
IN2
NC
8
7
6
5
ENABLE
V
+
OUT RTN
V
OUT
TOP VIEW
MS8 PACKAGE
8-LEAD PLASTIC MSOP
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
Conversion Accuracy
G
ERR
Low Frequency Gain Error 50Hz to 5kHz Input (Notes 6, 7) ±0.1 ±0.3 %
●±0.4 %
V
OOS
Output Offset Voltage (Notes 6, 7) 0.1 0.55 mV
∆V
OOS
/∆T Output Offset Drift (Note 11) ●210µV/°C
LIN
ERR
Linearity Error 50mV to 350mV (Notes 7, 8) ●0.02 0.15 %
PSRRG Power Supply Rejection (Note 9) 0.02 0.15 %/V
●0.20 %/V
V
IOS
Input Offset Voltage (Notes 6, 7, 10) 0.2 1.5 mV
∆V
IOS
/∆T Input Offset Drift (Note 11) ●110µV/°C
Additional Error vs Crest Factor (CF)
CF = 3 60Hz Fundamental, 200mV
RMS
●0.2 mV
CF = 5 60Hz Fundamental, 200mV
RMS
●5mV
Input Characteristics
V
IMAX
Maximum Peak Input Swing Accuracy = 1% (Note 14) ●1 1.05 V
I
VR
Input Voltage Range ●0V
+
V
Z
IN
Input Impedance Average, Differential (Note 12) 5 MΩ
Average, Common Mode (Note 12) 100 MΩ
CMRRI Input Common Mode Rejection (Note 13) ●50 400 µV/V
V
IMIN
Minimum RMS Input ●5mV
PSRRI Power Supply Rejection (Note 9) ●250 600 µV/V
3
LTC1967
1967f
The ● denotes specifications which apply over the full operating
temperature range, otherwise specifications are TA = 25°C. V+ = 5V, VOUTRTN = 2.5V, CAVE = 10µF, VIN = 200mVRMS, VENABLE = 0.5V
unless otherwise noted.
ELECTRICAL CHARACTERISTICS
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: The inputs (IN1, IN2) are protected by shunt diodes to GND and
V
+
. If the inputs are driven beyond the rails, the current should be limited
to less than 10mA.
Note 3: The LTC1967 output (V
OUT
) is high impedance and can be
overdriven, either sinking or sourcing current, to the limits stated.
Note 4: The LTC1967C/LTC1967I are guaranteed functional over the
operating temperature range of –40°C to 85°C.
Note 5: The LTC1967C is guaranteed to meet specified performance from
0°C to 70°C. The LTC1967C is designed, characterized and expected to
meet specified performance from –40°C to 85°C but is not tested nor QA
sampled at these temperatures. The LTC1967I is guaranteed to meet
specified performance from –40°C to 85°C.
Note 6: High speed automatic testing cannot be performed with
C
AVE
= 10µF. The LTC1967 is 100% tested with C
AVE
= 47nF. Correlation
tests have shown that the performance limits can be guaranteed with the
additional testing being performed to guarantee proper operation of all the
internal circuitry.
Note 7: High speed automatic testing cannot be performed with 60Hz
inputs. The LTC1967 is 100% tested with DC and 10kHz input signals.
Measurements with DC inputs from 50mV to 350mV are used to calculate
the four parameters: G
ERR
, V
OOS
, V
IOS
and linearity error. Correlation tests
have shown that the performance limits can be guaranteed with the
additional testing being performed to guarantee proper operation of all
internal circuitry.
Note 8: The LTC1967 is inherently very linear. Unlike older log/antilog
circuits, its behavior is the same with DC and AC inputs, and DC inputs are
used for high speed testing.
Note 9: The power supply rejections of the LTC1967 are measured with
DC inputs from 50mV to 350mV. The change in accuracy from V
+
= 4.5V
to V
+
= 5.5V is divided by 1V.
Note 10: Previous generation RMS-to-DC converters required nonlinear
input stages as well as a nonlinear core. Some parts specify a “DC reversal
error,” combining the effects of input nonlinearity and input offset voltage.
The LTC1967 behavior is simpler to characterize and the input offset
voltage is the only significant source of “DC reversal error.”
Note 11: Guaranteed by design.
Note 12: The LTC1967 is a switched capacitor device and the input/output
impedance is an average impedance over many clock cycles. The input
impedance will not necessarily lead to an attenuation of the input signal
measured. Refer to the Applications Information section titled “Input
Impedance” for more information.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
Output Characteristics
OVR Output Voltage Range ●0V
+
V
Z
OUT
Output Impedance (Note 12) ●40 50 65 kΩ
CMRRO Output Common Mode Rejection (Note 13) ●50 250 µV/V
V
OMAX
Maximum Differential Output Swing Accuracy = 1%, DC Input (Note 14) 1.0 1.05 V
●0.9 V
PSRRO Power Supply Rejection (Note 9) ●250 1000 µV/V
Frequency Response
f
1P
0.1% Additional Gain Error (Note 15) 40 kHz
f
–3dB
±3dB Frequency (Note 15) 4 MHz
Power Supplies
V
+
Supply Voltage ●4.5 5.5 V
I
S
Supply Current IN1 = 20mV, IN2 = 0V ●320 390 µA
IN1 = 200mV, IN2 = 0V 340 µA
Shutdown Characteristics
I
SS
Supply Current V
ENABLE
= 4.5V ●0.1 10 µA
I
IH
ENABLE Pin Current High V
ENABLE
= 4.5V ●–1 –0.1 µA
I
IL
ENABLE Pin Current Low V
ENABLE
= 0.5V ●–3 –0.5 –0.1 µA
V
TH
ENABLE Threshold Voltage 2.1 V
V
HYS
ENABLE Threshold Hysteresis 0.1 V
4
LTC1967
1967f
ELECTRICAL CHARACTERISTICS
Note 13: The common mode rejection ratios of the LTC1967 are measured
with DC inputs from 50mV to 350mV. The input CMRR is defined as the
change in V
IOS
measured between input levels of 0V to 350mV and input
levels of V
+
– 350mV to V
+
divided by V
+
– 350mV. The output CMRR is
defined as the change in V
OOS
measured with OUT RTN = 0V and OUT RTN
= V
+
– 350mV divided by V
+
– 350mV.
Note 14: The LTC1967 input and output voltage swings are limited by
internal clipping. However, its ∆Σ topology is relatively tolerant of
momentary internal clipping.
TYPICAL PERFOR A CE CHARACTERISTICS
UW
Gain and Offset
vs Output Common Mode Voltage
Gain and Offset
vs Input Common Mode Voltage
Note 15: The LTC1967 exploits oversampling and noise shaping to reduce
the quantization noise of internal 1-bit analog-to-digital conversions. At
higher input frequencies, increasingly large portions of this noise are
aliased down to DC. Because the noise is shifted in frequency, it becomes
a low frequency rumble and is only filtered at the expense of increasingly
long settling times. The LTC1967 is inherently wideband, but the output
accuracy is degraded by this aliased noise.
INPUT COMMON MODE VOLTAGE (V)
0
–0.7
GAIN ERROR (%)
OFFSET VOLTAGE (mV)
–0.6
–0.4
–0.3
–0.2
0.3
0
1.0 2.0 2.5 5.04.5
1967 G01
–0.5
0.1
0.2
–0.1
–1.0
–0.8
–0.4
–0.2
0
1.0
0.4
–0.6
0.6
0.8
0.2
0.5
50mV ≤ V
IN(PEAK)
≤ 350mV
1.5 3.0 3.5 4.0
V
IOS
V
OOS
GAIN ERROR
OUTPUT COMMON MODE VOLTAGE (V)
0
–0.5
GAIN ERROR (%)
OFFSET VOLTAGE (mV)
–0.4
–0.2
–0.1
0
0.5
0.2
1.0 2.0 2.5 5.04.5
1967 G02
–0.3
0.3
0.4
0.1
–1.0
–0.8
–0.4
–0.2
0
1.0
0.4
–0.6
0.6
0.8
0.2
0.5 1.5 3.0 3.5 4.0
V
IOS
V
OOS
GAIN ERROR
50mV ≤ V
IN(PEAK)
≤ 350mV
Gain and Offsets vs Temperature Gain and Offset vs Supply Voltage
TEMPERATURE (°C)
–40
GAIN ERROR (%)
OFFSET VOLTAGE (mV)
0.01
0.03
0.05
V
OOS
60
1967 G03
–0.01
–0.03
0
0.02
0.04
–0.02
–0.04
–0.05
0.1
0
0.3
0.5
–0.1
–0.3
0.2
0.4
–0.2
–0.4
–0.5
–15 10 35 85
V
IOS
GAIN ERROR
50mV ≤ V
IN(PEAK)
≤ 350mV
SUPPLY VOLTAGE (V)
4.5
–0.5
GAIN ERROR (%)
OFFSET VOLTAGE (mV)
–0.4
–0.2
–0.1
0
0.5
0.2
4.8 5.1 6.0
1967 G04
–0.3
0.3
0.4
0.1
–1.0
–0.8
–0.4
–0.2
0
1.0
0.4
–0.6
0.6
0.8
0.2
5.4 5.7
V
IOS
V
OOS
GAIN ERROR
50mV ≤ V
IN(PEAK)
≤ 350mV
5
LTC1967
1967f
TYPICAL PERFOR A CE CHARACTERISTICS
UW
Performance vs Large Crest Factors AC Linearity
DC Linearity Supply Current vs Supply Voltage Supply Current vs Temperature
Shutdown Current
vs ENABLE Voltage Input Signal Bandwidth
vs RMS Value
Performance vs Crest Factor
CREST FACTOR
1
199.0
199.8
199.6
199.4
199.2
OUTPUT VOLTAGE (mV DC)
200.0
200.2
200.4
200.6
2345
1kHz
1967 G05
200.8
201.0 200mVRMS SCR WAVEFORMS
CAVE = 10µF
O.1%/DIV
60Hz20Hz
CREST FACTOR
1
OUTPUT VOLTAGE (mV DC)
220
4
1967 G06
190
170
23 5
160
150
140
130
120
210
200
180
678
200mV
RMS
SCR WAVEFORMS
C
AVE
= 10µF
5%/DIV
60Hz
10Hz
10kHz
1kHz
20Hz
V
IN1
(mV AC
RMS
)
0
V
OUT
(mV DC) – V
IN
(mV AC
RMS
)
0.20
0.15
0.10
0.05
0
–0.05
–0.10
–0.15
–0.20 400
1967 G07
100 200 300 500
60Hz SINEWAVES
C
AVE
= 10µF
V
IN2
= MIDSUPPLY
VIN1 (mV)
–500
{VOUTDC – |VINDC|} (mV)
0.02
0.06
0.10
300
1967 G08
–0.02
–0.06
0
0.04
0.08
–0.04
–0.08
–0.10 –300 –100 100 500
CAVE = 1µF
VIN2 = MIDSUPPLY
EFFECTS OF OFFSETS
MAY BE POSITIVE OR
NEGATIVE AT VIN = 0V
SUPPLY VOLTAGE (V)
0
SUPPLY CURRENT (µA)
4
450
400
350
300
250
200
150
100
50
0
1967 G09
26
3
15
TEMPERATURE (°C)
–55
315
SUPPLY CURRENT (µA)
320
330
335
340
–15 25 45 125
1967 G10
325
–35 5 65 85 105
345 VS = 5V
ENABLE PIN VOLTAGE (V)
0
500
400
300
200
100
0
–100
0
–100
100
I
S
I
EN
–200
200
–300
300
–400
35
1967 G11
12 46
SUPPLY CURRENT (µA)
ENABLE PIN CURRENT (nA)
INPUT SIGNAL FREQUENCY (Hz)
10
OUTPUT DC VOLTAGE (mV)
100
100 10k 100k 1M
1967 G12
11k
1000
10M
0.1% ERROR 10%
ERROR
–3dB
1% ERROR
Input Signal Bandwidth
INPUT SIGNAL FREQUENCY (Hz)
100
190
OUTPUT DC VOLTAGE (mV)
192
194
196
198
1k 10k 100k 1M 10M
1967 G13
188
186
184
182
200
202
1%/DIV
C
AVE
= 1µF
6
LTC1967
1967f
TYPICAL PERFOR A CE CHARACTERISTICS
UW
Bandwidth to 200kHz DC Transfer Function Near Zero Input Common Mode Rejection
Ratio vs Frequency
Output Accuracy
vs Signal Amplitude
INPUT FREQUENCY (Hz)
0
199
200
202
150k
1967 G14
198
197
50k 100k 200k
196
195
201
OUTPUT VOLTAGE (mV)
0.5%/DIV
C
AVE
= 47µF
VIN1 (mV DC)
–30
–10
VOUT (mV DC)
0
10
20
–20 –10 010
1967 G15
20
30
40
–5
5
15
25
35
30
VIN2 = MIDSUPPLY
THREE REPRESENTATIVE UNITS
INPUT FREQUENCY (Hz)
10
0
INPUT CMRR (dB)
20
40
60
100 1k 10k 100k
1967 G16
1M
80
100
10
30
50
70
90
10M
4.5V COMMON
MODE INPUT
CONVERSION
TO DC OUTPUT
V
IN1
(V
RMS
)
0
–20
{V
OUT
(mV DC) – V
IN
(mV
RMS
)} (mV)
–15
–10
–5
0
5
10
0.5 1 1.5
DC
2
1967 G17
1% ERROR V
IN2
= MIDSUPPLY
–1% ERROR
AC – 60Hz
SINEWAVE
Output Noise vs Input Frequency
INPUT FREQUENCY (Hz)
1k
0.001
PEAK OUTPUT NOISE (% OF READING)
0.01
0.1
1
10k 100k
1967 G18
PEAK NOISE DURING
10 SECOND MEASUREMENT
C
AVE
= 1µF
C
AVE
= 100µF
C
AVE
= 10µF
7
LTC1967
1967f
GND (Pin 1): Ground. The power return pin.
IN1 (Pin 2): Differential Input. DC coupled (polarity is
irrelevant).
IN2 (Pin 3): Differential Input. DC coupled (polarity is
irrelevant).
V
OUT
(Pin 5): Output Voltage. This is high impedance. The
RMS averaging is accomplished with a single shunt ca-
pacitor from this node to OUT RTN. The transfer function
is given by:
V OUT RTN Average IN IN
OUT
––
()
=
()
21
2
UU
U
PI FU CTIO S
OUT RTN (Pin 6): Output Return. The output voltage is
created relative to this pin. The VOUT and OUT RTN pins
are not balanced and this pin should be tied to a low
impedance, both AC and DC. Although it is often tied to
GND, it can be tied to any arbitrary voltage:
GND < OUT RTN < (V+ – Max Output)
V
+
(Pin 7): Positive Voltage Supply. 4.5V to 5.5V.
ENABLE (Pin 8): An Active-Low Enable Input. LTC1967 is
debiased if open circuited or driven to V
+
. For normal
operation, pull to GND.
APPLICATIO S I FOR ATIO
WUUU
RMS-TO-DC CONVERSION
Definition of RMS
RMS amplitude is the consistent, fair and standard way to
measure and compare dynamic signals of all shapes and
sizes. Simply stated, the RMS amplitude is the heating
potential of a dynamic waveform. A 1V
RMS
AC waveform
will generate the same heat in a resistive load as will 1V DC.
Mathematically, RMS is the “Root of the Mean of the
Square”:
VV
RMS
=
2
+
–
R1V DC
R
1967 F01
SAME
HEAT
1V AC
RMS
R1V (AC + DC) RMS
Figure 1
Alternatives to RMS
Other ways to quantify dynamic waveforms include peak
detection and average rectification. In both cases, an
average (DC) value results, but the value is only accurate
at the one chosen waveform type for which it is calibrated,
typically sine waves. The errors with average rectification
are shown in Table 1. Peak detection is worse in all cases
and is rarely used.
Table 1. Errors with Average Rectification vs True RMS
AVERAGE
RECTIFIED
WAVEFORM V
RMS
(V) ERROR*
Square Wave 1.000 1.000 11%
Sine Wave 1.000 0.900 *Calibrate for 0% Error
Triangle Wave 1.000 0.866 –3.8%
SCR at 1/2 Power, 1.000 0.637 –29.3%
Θ = 90°
SCR at 1/4 Power, 1.000 0.536 –40.4%
Θ = 114°
The last two entries of Table 1 are chopped sine waves as
is commonly created with thyristors such as SCRs and
Triacs. Figure 2a shows a typical circuit and Figure 2b
shows the resulting load voltage, switch voltage and load
8
LTC1967
1967f
the lowpass filter. The input to the LPF is the calculation
from the multiplier/divider; (VIN)2/VOUT. The lowpass
filter will take the average of this to create the output,
mathematically:
APPLICATIO S I FOR ATIO
WUUU
currents. The power delivered to the load depends on the
firing angle, as well as any parasitic losses such as switch
“ON” voltage drop. Real circuit waveforms will also typi-
cally have significant ringing at the switching transition,
dependent on exact circuit parasitics. For the purposes of
this data sheet, “SCR Waveforms” refers to the ideal
chopped sine wave, though the LTC1967 will do faithful
RMS-to-DC conversion with real SCR waveforms as well.
The case shown is for Θ = 90°, which corresponds to 50%
of available power being delivered to the load. As noted in
Table 1, when Θ = 114°, only 25% of the available power
is being delivered to the load and the power drops quickly
as Θ approaches 180°.
With an average rectification scheme and the typical
calibration to compensate for errors with sine waves, the
RMS level of an input sine wave is properly reported; it is
only with a non-sinusoidal waveform that errors occur.
Because of this calibration, and the output reading in
V
RMS
, the term True-RMS got coined to denote the use of
an actual RMS-to-DC converter as opposed to a calibrated
average rectifier.
CONTROL
V
LOAD
AC
MAINS V
LINE
V
THY
1967 F02a
+
+
–
+
–
–
I
LOAD
V
LINE
Θ
V
LOAD
V
THY
I
LOAD
1967 F02b
Figure 2a
Figure 2b
How an RMS-to-DC Converter Works
Monolithic RMS-to-DC converters use an implicit compu-
tation to calculate the RMS value of an input signal. The
fundamental building block is an analog multiply/divide
used as shown in Figure 3. Analysis of this topology is
easy and starts by identifying the inputs and the output of
VV
V
V
V
Vso
VV
Vand
VVor
V V RMS V
OUT IN
OUT
OUT
IN
OUT
OUT
IN
OUT
OUT IN
OUT IN IN
=
()
()
=
()
=
()
()
=
()
=
()
=
()
2
22
2
22
2
,
,
,
,
Because V is DC,
V
OUT
IN
Figure 3. RMS-to-DC Converter with Implicit Computation
VIN VOUT
1967 F03
÷×LPF
V
V
IN
OUT
()
2
Unlike the prior generation RMS-to-DC converters, the
LTC1967 computation does NOT use log/antilog circuits,
which have all the same problems, and more, of log/
antilog multipliers/dividers, i.e., linearity is poor, the band-
width changes with the signal amplitude and the gain drifts
with temperature.
How the LTC1967 RMS-to-DC Converter Works
The LTC1967 uses a completely new topology for RMS-to-
DC conversion, in which a ∆Σ modulator acts as the
divider, and a simple polarity switch is used as the multi-
plier
1
as shown in Figure 4.
1
Protected by multiple patents.
9
LTC1967
1967f
APPLICATIO S I FOR ATIO
WUUU
Note that the internal scalings are such that the ∆Σ output
duty cycle is limited to 0% or 100% only when V
IN
exceeds
±4 • V
OUT
.
Linearity of an RMS-to-DC Converter
Linearity may seem like an odd property for a device that
implements a function that includes two very nonlinear
processes: squaring and square rooting.
However, an RMS-to-DC converter has a transfer func-
tion, RMS volts in to DC volts out, that should ideally have
a 1:1 transfer function. To the extent that the input to
output transfer function does not lie on a straight line, the
part is nonlinear.
A more complete look at linearity uses the simple model
shown in Figure 5. Here an ideal RMS core is corrupted by
both input circuitry and output circuitry that have imper-
fect transfer functions. As noted, input offset is introduced
in the input circuitry, while output offset is introduced in
the output circuitry.
Any nonlinearity that occurs in the output circuity will
corrupt the RMS in to DC out transfer function. A nonlin-
earity in the input circuitry will typically corrupt that
transfer function far less simply because with an AC input,
the RMS-to-DC conversion will average the nonlinearity
from a whole range of input values together.
But the input nonlinearity will still cause problems in an
RMS-to-DC converter because it will corrupt the accuracy
as the input signal shape changes. Although an RMS-to-
DC converter will convert any input waveform to a DC
output, the accuracy is not necessarily as good for all
waveforms as it is with sine waves. A common way to
describe dynamic signal wave shapes is Crest Factor. The
crest factor is the ratio of the peak value relative to the RMS
value of a waveform. A signal with a crest factor of 4, for
instance, has a peak that is four times its RMS value.
The ∆Σ modulator has a single-bit output whose average
duty cycle (D) will be proportional to the ratio of the input
signal divided by the output. The ∆Σ is a 2nd order
modulator with excellent linearity. The single-bit output is
used to selectively buffer or invert the input signal. Again,
this is a circuit with excellent linearity, because it operates
at only two points: ±1 gain; the average effective multipli-
cation over time will be on the straight line between these
two points. The combination of these two elements again
creates a lowpass filter input signal equal to (V
IN
)
2
/V
OUT
,
which, as shown above, results in RMS-to-DC conversion.
The lowpass filter performs the averaging of the RMS
function and must be a lower corner frequency than the
lowest frequency of interest. For line frequency measure-
ments, this filter is simply too large to implement on-chip,
but the LTC1967 needs only one capacitor on the output
to implement the lowpass filter. The user can select this
capacitor depending on frequency range and settling time
requirements, as will be covered in the Design Cookbook
section to follow.
This topology is inherently more stable and linear than log/
antilog implementations primarily because all of the signal
processing occurs in circuits with high gain op amps
operating closed loop.
More detail of the LTC1967 inner workings is shown in the
Simplified Schematic towards the end of this data sheet.
Figure 4. Topology of LTC1967
∆-Σ
REF
V
IN
V
OUT
LPF
1967 F04
±1
DV
V
IN
OUT
α
INPUT CIRCUITRY
• V
IOS
• INPUT NONLINEARITY
IDEAL
RMS-TO-DC
CONVERTER
OUTPUT CIRCUITRY
• V
OOS
• OUTPUT NONLINEARITY
INPUT OUTPUT
1967 F05
Figure 5. Linearity Model of an RMS-to-DC Converter
10
LTC1967
1967f
Because this peak has energy (proportional to voltage
squared) that is 16 times (4
2
) the energy of the RMS value,
the peak is necessarily present for at most 6.25% (1/16)
of the time.
The LTC1967 performs very well with crest factors of 4 or
less and will respond with reduced accuracy to signals
with higher crest factors. The high performance with crest
factors less than 4 is directly attributable to the high
linearity throughout the LTC1967.
DESIGN COOKBOOK
The LTC1967 RMS-to-DC converter makes it easy to
implement a rather quirky function. For many applications
all that will be needed is a single capacitor for averaging,
appropriate selection of the I/O connections and power
supply bypassing. Of course, the LTC1967 also requires
power. A wide variety of power supply configurations are
shown in the Typical Applications section towards the end
of this data sheet.
Capacitor Value Selection
The RMS or root-mean-squared value of a signal,
the root
of the mean of the square
, cannot be computed without
some averaging to obtain the
mean
function. The LTC1967
true RMS-to-DC converter utilizes a single capacitor on
the output to do the low frequency averaging required for
RMS-to-DC conversion. To give an accurate measure of a
dynamic waveform, the averaging must take place over a
sufficiently long interval to average, rather than track, the
lowest frequency signals of interest. For a single averaging
capacitor, the accuracy at low frequencies is depicted in
Figure 6.
Figure 6 depicts the so-called “DC error” that results at a
given combination of input frequency and filter capacitor
values
2
. It is appropriate for most applications, in which
the output is fed to a circuit with an inherently band-limited
frequency response, such as a dual slope/integrating A/D
converter, a ∆Σ A/D converter or even a mechanical analog
meter.
However, if the output is examined on an oscilloscope with
a very low frequency input, the incomplete averaging will
be seen, and this ripple will be larger than the error
depicted in Figure 6. Such an output is depicted in
Figure␣ 7. The ripple is at twice the frequency of the input
APPLICATIO S I FOR ATIO
WUUU
Figure 6. DC Error vs Input Frequency
INPUT FREQUENCY (Hz)
1
–2.0
DC ERROR (%)
–1.6
–1.2
–0.8
–0.4
10 100
1967 F06
0
–1.8
–1.4
–1.0
–0.6
–0.2
C = 0.1µFC = 0.22µFC = 0.47µFC = 1µF
C = 10µF
C = 2.2µF
C = 22µF
C = 4.7µF
Figure 7. Output Ripple Exceeds DC Error
TIME
OUTPUT
1967 F07
DC
ERROR
(0.05%)
IDEAL
OUTPUT
DC
AVERAGE
OF ACTUAL
OUTPUT
PEAK
RIPPLE
(5%)
ACTUAL OUTPUT
WITH RIPPLE
f = 2 × f
INPUT
PEAK
ERROR =
DC ERROR +
PEAK RIPPLE
(5.05%)
2
This frequency-dependent error is in additon to the static errors that affect all readings and are
therefore easy to trim or calibrate out. The “Error Analyses” section to follow discusses the effect
of static error terms.
11
LTC1967
1967f
APPLICATIO S I FOR ATIO
WUUU
because of the computation of the square of the input. The
typical values shown, 5% peak ripple with 0.05% DC error,
occur with C
AVE
= 1.5µF and f
INPUT
= 10Hz.
If the application calls for the output of the LTC1967 to feed
a sampling or Nyquist A/D converter (or other circuitry
that will not average out this double frequency ripple) a
larger averaging capacitor can be used. This trade-off is
depicted in Figure 8. The peak ripple error can also be
reduced by additional lowpass filtering after the LTC1967,
but the simplest solution is to use a larger averaging
capacitor.
A 2.2µF capacitor is a good choice for many applications.
The peak error at 50Hz/60Hz will be <1% and the DC error
will be <0.1% with frequencies of 10Hz or more.
Note that both Figure 6 and Figure 8 assume AC-coupled
waveforms with a crest factor less than 2, such as sine
waves or triangle waves. For higher crest factors and/or
AC + DC waveforms, a larger C
AVE
will generally be
required. See “Crest Factor and AC + DC Waveforms.”
Capacitor Type Selection
The LTC1967 can operate with many types of capacitors.
The various types offer a wide array of sizes, tolerances,
parasitics, package styles and costs.
Ceramic chip capacitors offer low cost and small size, but
are not recommended for critical applications. The value
stability over voltage and temperature is poor with many
types of ceramic dielectrics. This will not cause an RMS-
to-DC accuracy problem except at low frequencies, where
it can aggravate the effects discussed in the previous
section. If a ceramic capacitor is used, it may be neces-
sary to use a much higher nominal value in order to
assure the low frequency accuracy desired.
Another parasitic of ceramic capacitors is leakage, which
is again dependent on voltage and particularly tempera-
ture. If the leakage is a constant current leak, the I • R drop
of the leak multiplied by the output impedance of the
LTC1967 will create a constant offset of the output voltage.
If the leak is Ohmic, the resistor divider formed with the
LTC1967 output impedance will cause a gain error. For
<0.1% gain accuracy degradation, the parallel impedance
of the capacitor leakage will need to be >1000 times the
LTC1967 output impedance. Accuracy at this level can be
hard to achieve with a ceramic capacitor, particularly with
a large value of capacitance and at high temperature.
For critical applications, a film capacitor, such as metal-
ized polyester, will be a much better choice. Although
more expensive, and larger for a given value, the value
stability and low leakage make metal-film capacitors a
trouble-free choice.
With any type of capacitor, the self-resonance of the
capacitor can be an issue with the switched capacitor
LTC1967. If the self-resonant frequency of the averaging
capacitor is 1MHz or less, a second smaller capacitor
should be added in parallel to reduce the impedance seen
by the LTC1967 output stage at high frequencies. A
capacitor 100 times smaller than the averaging capacitor
will typically be small enough to be a low cost ceramic with
a high quality dielectric such as X7R or NPO/COG.
Figure 8. Peak Error vs Input Frequency with One Cap Averaging
INPUT FREQUENCY (Hz)
1
–2.0
PEAK ERROR (%)
–1.6
–1.2
–0.8
–0.4
10 100
1967 F08
0
–1.8
–1.4
–1.0
–0.6
–0.2 C = 100µF
C = 47µF
C = 22µF C = 10µF C = 4.7µF C = 2.2µF C = 1µF
12
LTC1967
1967f
Input Connections
The LTC1967 input is differential and DC coupled. The
LTC1967 responds to the RMS value of the differential
voltage between Pin 2 and Pin 3, including the DC portion
of that difference. However, there is no DC-coupled path
from the inputs to ground. Therefore, at least one of the two
inputs must be connected with a DC-return path to ground.
Both inputs must be connected to something. If either
input is left floating, a zero volt output will result.
For single-ended DC-coupled applications, simply con-
nect one of the two inputs (they are interchangeable) to
the signal, and the other to ground. This will work well for
dual supply configurations, but for single supply con-
figurations it will only work well for unipolar input sig-
nals. The LTC1967 input voltage range is from rail-to-rail,
and when the input is driven above V
+
or below GND the
gain and offset errors will increase substantially after just
a few hundred millivolts of overdrive. Fortunately, most
single supply circuits measuring a DC-coupled RMS
value will include some reference voltage other than
ground, and the second LTC1967 input can be connected
to that point.
For single-ended AC-coupled applications, Figure 9 shows
three alternate topologies. The first one, shown in Figure
9a uses a coupling capacitor to one input while the other
is grounded. This will remove the DC voltage difference from
the input to the LTC1967, and it will therefore not be part
of the resulting output voltage. Again, this connection will
APPLICATIO S I FOR ATIO
WUUU
work well with dual supply configurations, but in single
supply configurations it will be necessary to raise the volt-
age on the grounded input to assure that the signal at the
active input stays within the range of 0V to V
+
. If there is
already a suitable voltage reference available, connect the
second input to that point. If not, a midsupply voltage can
be created with two resistors as shown in Figure 9b.
Finally, if the input voltage is known to be between 0V and
V
+
, it can be AC coupled by using the configuration shown
in Figure 9c. Whereas the DC return path was provided
through Pin 3 in Figures 9a and 9b, in this case, the return
path is provided on Pin 2, through the input signal volt-
ages. The switched capacitor action between the two input
pins of the LTC1967 will cause the voltage on the coupling
capacitor connected to the second input to follow the DC
average of the input voltage.
For differential input applications, connect the two inputs to
the differential signal. If AC coupling is desired, one of the
two inputs can be connected through a series capacitor.
In all of these connections, to choose the input coupling
capacitor, C
C
, calculate the low frequency coupling time
constant desired, and divide by the LTC1967 differential
input impedance. Because the LTC1967 input impedance
is about 100 times its output impedance, this capacitor is
typically much smaller than the output averaging capaci-
tor. Its requirements are also much less stringent, and a
ceramic chip capacitor will usually suffice.
Figure 9. Single-Ended AC-Coupled Input Connection Alternatives
+
–
LTC1967
GND
V+V+V+
V–
(9a)
CC
IN1
VIN IN2
2
3
LTC1967
(9b)
CC
R1
20k R2
20k
IN1
VIN
V+
IN2
2
3
LTC1967
(9c)
CC
IN1
VIN
1967 F07
VDC
IN2
2
3
13
LTC1967
1967f
Output Connections
The LTC1967 output is differentially, but not symmetri-
cally, generated. That is to say, the RMS value that the
LTC1967 computes will be generated on the output (Pin 5)
relative to the output return (Pin 6), but these two pins are
not interchangeable. For most applications, Pin 6 will be
tied to ground (Pin 1). However, Pin 6 can be tied to any
voltage between 0V and V
+
(Pin 7) less the maximum
output voltage swing desired. This last restriction keeps
V
OUT
itself (Pin 5) within the range of 0V to V
+
. If a
reference level other than ground is used, it should be a
low impedance, both AC and DC, for proper operation of
the LTC1967.
In any configuration, the averaging capacitor should be
connected between Pins 5 and 6. The LTC1967 RMS-DC
output will be a positive voltage created at V
OUT
(Pin 5)
with respect to OUT RTN (Pin 6).
Power Supply Bypassing
The LTC1967 is a switched capacitor device, and large
transient power supply currents will be drawn as the
switching occurs. For reliable operation, standard power
supply bypassing must be included. A 0.01µF capacitor
from V
+
(Pin 7) to GND (Pin␣ 1) located close to the device
will suffice. If there is a good quality ground plane avail-
able, the capacitors can go directly to that instead. Power
supply bypass capacitors can, of course, be inexpensive
ceramic types.
Up and Running!
If you have followed along this far, you should have the
LTC1967 up and running by now! Don’t forget to enable
the device by grounding Pin 8, or driving it with a logic low.
Keep in mind that the LTC1967 output impedance is fairly
high, and that even the standard 10MΩ input impedance
of a digital multimeter (DMM) or a 10× scope probe will load
down the output enough to degrade its typical gain error
of 0.1%. In the end application circuit, either a buffer or
another component with an extremely high input imped-
ance (such as a dual slope integrating ADC) should be used.
APPLICATIO S I FOR ATIO
WUUU
For laboratory evaluation, it may suffice to use a bench-top
DMM with the ability to disconnect the 10MΩ shunt.
If you are still having trouble, it may be helpful to skip
ahead a few pages and review the Troubleshooting Guide.
What About Response Time?
With a large value averaging capacitor, the LTC1967 can
easily perform RMS-to-DC conversion on low frequency
signals. It compares quite favorably in this regard to prior-
generation products because nothing about the ∆Σ
circuitry is temperature sensitive. So the RMS result
doesn’t get distorted by signal driven thermal fluctuations
like a log-antilog circuit output does.
However, using large value capacitors results in a slow
response time. Figure 10 shows the rising and falling step
responses with a 1µF averaging capacitor. Although they
both appear at first glance to be standard exponential-
decay type settling, they are not. This is due to the
nonlinear nature of an RMS-to-DC calculation. Also note
the change in the time scale between the two; the rising
edge is more than twice as fast to settle to a given
accuracy. Again this is a necessary consequence of RMS-
to-DC calculation.
3
Although shown with a step change between 0mV and
100mV, the same response shapes will occur with the
LTC1967 for ANY step size. This is in marked contrast to
prior generation log/antilog RMS-to-DC converters, whose
averaging time constants are dependent on the signal
level, resulting in excruciatingly long waits for the output
to go to zero.
The shape of the rising and falling edges will be dependent
on the total percent change in the step, but for less than the
100% changes shown in Figure 10, the responses will be
less distorted and more like a standard exponential decay.
For example, when the input amplitude is changed from
3
To convince oneself of this necessity, consider a pulse train of 50% duty cycle between 0mV and
100mV. At very low frequencies, the LTC1967 will essentially track the input. But as the input
frequency is increased, the average result will converge to the RMS value of the input. If the rise and
fall characteristics were symmetrical, the output would converge to 50mV. In fact though, the RMS
value of a 100mV DC-coupled 50% duty cycle pulse train is 70.71mV, which the asymmetrical rise
and fall characteristics will converge to as the input frequency is increased.
14
LTC1967
1967f
100mV to 110mV (+10%) and back (–10%), the step
responses are essentially the same as a standard expo-
nential rise and decay between those two levels. In such
cases, the time constant of the decay will be in between
that of the rising edge and falling edge cases of Figure 10.
Therefore, the worst case is the falling edge response as
it goes to zero, and it can be used as a design guide.
Figure␣ 11 shows the settling accuracy vs settling time for
a variety of averaging capacitor values. If the capacitor
value previously selected (based on error requirements)
gives an acceptable settling time, your design is done.
But with 100µF, the settling time to even 10% is a full 20
seconds, which is a long time to wait. What can be done
about such a design? If the reason for choosing 100µF is
to keep the DC error with a 100mHz input less than 0.1%,
the answer is: not much. The settling time to 1% of 32
seconds is just 3.2 cycles of this extremely low frequency.
Averaging very low frequency signals takes a long time.
However, if the reason for choosing 100µF is to keep the
peak error with a 10Hz input less than 0.1%, there is
another way to achieve that result with a much improved
settling time.
APPLICATIO S I FOR ATIO
WUUU
TIME (SEC)
0
0
OUTPUT (mV)
20
40
60
80
100
120
0.05 0.1 0.15 0.2
1967 F10a
0.25
C
AVE
= 1µF
Figure 10a. LTC1967 Rising Edge with CAVE = 1µFFigure 10b. LTC1967 Falling Edge with CAVE = 1µF
Figure 11. Settling Time with One Cap Averaging
TIME (SEC)
0
0
OUTPUT (mV)
20
40
60
80
100
120
0.1 0.2 0.3 0.4
1967 F10b
0.5
C
AVE
= 1µF
SETTLING TIME (SEC)
0.01
0.1
SETTLING ACCURACY (%)
1
10
1100.1 100
1966 F12
C = 0.1µF C = 0.22µF C = 0.47µF C = 1µF C = 2.2µF C = 4.7µF C = 10µF C = 22µF C = 47µF C = 100µF
15
LTC1967
1967f
Reducing Ripple with a Post Filter
The output ripple is always much larger than the DC error,
so filtering out the ripple can reduce the peak error
substantially, without the large settling time penalty of
simply increasing the averaging capacitor.
Figure 12 shows a basic 2nd order post filter, for a net 3rd
order filtering of the LTC1967 RMS calculation. It uses the
50kΩ output impedance of the LTC1967 as the first resis-
tor of a 3rd order Sallen-Key active-RC filter. This topology
features a buffered output, which can be desirable de-
pending on the application. However, there are disadvan-
tages to this topology, the first of which is that the op amp
input voltage and current errors directly degrade the effec-
tive LTC1967 V
OOS
. The table inset in Figure 12 shows
these errors for four of Linear Technology’s op amps.
A second disadvantage is that the op amp output has to
operate over the same range as the LTC1967 output, includ-
ing ground, which in single supply applications is the nega-
tive supply. Although the LTC1967 output will function fine
just millivolts from the rail, most op amp output stages (and
even some input stages) will not. There are at least two ways
to address this. First of all, the op amp can be operated split
supply if a negative supply is available. Just the op amp
would need to do so; the LTC1967 can remain single sup-
ply. A second way to address this issue is to create a signal
reference voltage a half volt or so above ground. This is most
attractive when the circuitry that follows has a differential
input, so that the tolerance of the signal reference is not a
APPLICATIO S I FOR ATIO
WUUU
concern. To do this, tie all three ground symbols shown in
Figure 12 to the signal reference, as well as to the differ-
ential return for the circuitry that follows.
Figure 13 shows an alternative 2nd order post filter, for a
net 3rd order filtering of the LTC1967 RMS calculation. It
also uses the 50kΩ output impedance of the LTC1967 as
the first resistor of a 3rd order active-RC filter, but this
topology filters without buffering so that the op amp DC
error characteristics do not affect the output. Although the
output impedance of the LTC1967 is increased from 50kΩ
to 168kΩ, this is not an issue with an extremely high input
impedance load, such as a dual-slope integrating ADC like
the ICL7106. And it allows a generic op amp to be used,
such as the SOT-23 one shown. Furthermore, it easily
works on a single supply rail by tying the noninverting
input of the op amp to a low noise reference as optionally
shown. This reference will not change the DC voltage at the
circuit output, although it does become the AC ground for
the filter, thus the (relatively) low noise requirement.
Step Responses with a Post Filter
B
oth of the post filters, shown in Figures 12 and 13, are
optimized for additional filtering with clean step re-
sponses. The 50kΩ output impedance of the LTC1967
working into a 2.2µF capacitor forms a 1st order LPF with
a –3dB frequency of ~1.45Hz. The two filters have 2.2µF
at the LTC1967 output for easy comparison with a
2.2µF-only case, and both have the same relative Bessel-
like shape. However, because of the topological differ-
ences of pole placements between the various compo-
nents within the two filters, the net effective bandwidth
for Figure 12 is slightly higher (≈1.2 • 1.45 ≈ 1.7Hz) than
with 2.2µF alone, while the bandwidth for Figure 13 is
Figure 13. DC Accurate Post Filter
Figure 12. Buffered Post Filter
LTC1967 C
AVE
2.2µF
5
6
R1
23.2k
–
+
R2
102k
R
B
C2
0.22µF
C1
2.2µF
LT1880
1967 F12
OP AMP
LTC1967 V
OOS
V
IOS
I
B/OS
• R
TOTAL OFFSET
R
B
VALUE
I
SQ
LT1494
±375µV
±43µV
±918µV
174k
1µA
LT1880
±150µV
±195µV
±845µV
SHORT
1.2mA
LT1077
±60µV
±329µV
±889µV
174k
48µA
LTC2054
±3µV
±52µV
±555µV
SHORT
150µA
±500µV
LTC1967 C
AVE
2.2µF
5
6
OTHER
REF VOLTAGE,
SEE TEXT
R1
118k
–
+
R2
402k
C1
0.47µFC2
0.47µF
LT1782
1067 F13
16
LTC1967
1967f
APPLICATIO S I FOR ATIO
WUUU
somewhat lower (≈0.7 • 1.45 ≈ 1Hz) than with 2.2µF
alone. To adjust the bandwidth of either of them, simply
scale all the capacitors by a common multiple, and leave
the resistors unchanged.
The step responses of the LTC1967 with 2.2µF-only and
with the two post filters are shown in Figure 14. This is the
rising edge RMS output response to a 10Hz input starting
at t = 0. Although the falling edge response is the worst
case for settling, the rising edge illustrates the ripple that
these post filters are designed to address, so the rising
edge makes for a better intuitive comparison.
The initial rise of the LTC1967 will have enhanced slew rates
with DC and very low frequency inputs due to saturation
effects in the ∆Σ modulator. This is seen in Figure 14 in two
ways. First, the 2.2µF-only output is seen to rise very quickly
in the first 40ms. The second way this effect shows up is
that the post filter outputs have a modest overshoot, on the
order of 3mV to 4mV, or 3% to 4%. This is only an issue
with input frequency bursts at 50Hz or less, and even with
the overshoot, the settling to a given level of accuracy
improves due to the initial speedup.
As predicted by Figure 6, the DC error with 2.2µF is well
under 1mV and is not noticeable at this scale. However, as
predicted by Figure 8, the peak error with the ripple from
a 10Hz input is much larger, in this case about 5mV. As can
be clearly seen, the post filters reduce this ripple. Even the
wider bandwidth of Figure 12’s filter is seen to cut the
ripple down substantially (to <1mV) while the settling to
1% happens faster. With the narrower bandwidth of Figure
14’s filter, the step response is somewhat slower, but the
double frequency output ripple is just 150µV.
Figure 15 shows the step response of the same three cases
with a burst of 60Hz rather than 10Hz. With 60Hz, the initial
portion of the step response is free of the boost seen in
Figure 14 and the two post-filter responses have less than
1% overshoot. The 2.2µF-only case still has noticeable
120Hz ripple, but both filters have removed all detectable
ripple on this scale. This is to be expected; the first order
filter will reduce the ripple about 6:1 for a 6:1 change in
frequency, while the third order filters will reduce the
ripple about 6
3
:1 or 216:1 for a 6:1 change in frequency.
Again, the two filter topologies have the same relative
shape, so the step response and ripple filtering trade-offs
of the two are the same, with the same performance of
each possible with the other by scaling it accordingly.
Figures 16 and 17 show the peak error vs. frequency for a
selection of capacitors for the two different filter topolo-
gies. To keep the clean step response, scale all three
capacitors within the filter. Scaling the buffered topology
of Figure 12 is simple because the capacitors are in a
10:1:10 ratio. Scaling the DC accurate topology of Figure
14 can be done with standard value capacitors; one decade
of scaling is shown in Table 2.
Table 2: One Decade of Capacitor Scaling for Figure 13 with EIA
Standard Values
C
AVE
C
1
= C
2
=
1µF 0.22µF
1.5µF 0.33µF
2.2µF 0.47µF
3.3µF 0.68µF
4.7µF1µF
6.8µF1.5µF
Figure 15. Step Responses with 60Hz Burst
Figure 14. Step Responses with 10Hz Burst
INPUT
BURST
200mV/
DIV
20mV/
DIV
2.2µF ONLY
FIGURE 12
FIGURE 13
STEP
RESPONSE
100ms/DIV 1967 F14
INPUT
BURST
200mV/
DIV
20mV/
DIV
2.2µF ONLY
FIGURE 12
FIGURE 13
STEP
RESPONSE
100ms/DIV
1967 F15
17
LTC1967
1967f
APPLICATIO S I FOR ATIO
WUUU
Figures 18 and 19 show the settling time versus settling
accuracy for the Buffered and DC accurate post filters,
respectively. The different curves represent different
scalings of the filters, as indicated by the C
AVE
value. These
are comparable to the curves in Figure 11 (single capacitor
case), with somewhat less settling time for the buffered
post filter, and somewhat more settling time for the
DC-accurate post filter. These differences are due to the
change in overall bandwidth as mentioned earlier.
Although the settling times for the post-filtered configura-
tions shown on Figures 18 and 19 are not that much
different from those with a single capacitor, the point of
using a post filter is that the settling times are far better for
a given level peak error. The filters dramatically reduce the
low frequency averaging ripple with far less impact on
settling time.
Crest Factor and AC + DC Waveforms
In the preceding discussion, the waveform was assumed
to be AC coupled, with a modest crest factor. Both
assumptions ease the requirements for the averaging
capacitor. With an AC-coupled sine wave, the calculation
engine squares the input, so the averaging filter that
follows is required to filter twice the input frequency,
making its job easier. But with a sinewave that includes
DC offset, the square of the input has frequency content
at the input frequency and the filter must average out that
lower frequency. So with AC + DC waveforms, the re-
quired value for CAVE should be based on half of the lowest
input frequency, using the same design curves presented
in Figures 6, 8, 16 and 17.
Figure 17. Peak Error vs Input Frequency with DC-Accurate Post Filter
Figure 16. Peak Error vs Input Frequency with Buffered Post Filter
INPUT FREQUENCY (Hz)
1
–2.0
PEAK ERROR (%)
–1.6
–1.2
–0.8
–0.4
10 100
1967 F16
0
–1.8
–1.4
–1.0
–0.6
–0.2 C = 22µF
C = 10µF C = 4.7µF C = 2.2µF C = 1µF C = 0.47µF C = 0.22µF
INPUT FREQUENCY (Hz)
1
–2.0
PEAK ERROR (%)
–1.6
–1.2
–0.8
–0.4
10 100
1967 F17
0
–1.8
–1.4
–1.0
–0.6
–0.2 C = 10µF
C = 4.7µF C = 2.2µF C = 1µF C = 0.47µF C = 0.22µF C = 0.1µF
18
LTC1967
1967f
APPLICATIO S I FOR ATIO
WUUU
Crest factor, which is the peak to RMS ratio of a dynamic
signal, also effects the required C
AVE
value. With a higher
crest factor, more of the energy in the signal is concentrated
into a smaller portion of the waveform, and the averaging
has to ride out the long lull in signal activity. For busy
waveforms, such as a sum of sine waves, ECG traces or
SCR-chopped sine waves, the required value for C
AVE
should be based on the lowest fundamental input frequency
divided as such:
ff
CF
DESIGN INPUT MIN
=()
•–32
using the same design curves presented in Figures 6, 8,
16 and 17. For the worst case of square top pulse trains,
that are always either zero volts or the peak voltage, base
the selection on the lowest fundamental input frequency
divided by twice as much:
ff
CF
DESIGN INPUT MIN
=()
•–62
The effects of crest factor and DC offsets are cumulative.
So for example, a 10% duty cycle pulse train from 0V
PEAK
to 1V
PEAK
(CF = √10 = 3.16) repeating at 16.67ms (60Hz)
input is effectively only 30Hz due to the DC asymmetry and
is effectively only:
fHz
DESIGN ==
30
6 3 16 2 378
•.– .
for the purposes of Figures 6, 8, 16 and 17.
Obviously, the effect of crest factor is somewhat simplified
above given the factor of two difference based on a
subjective description of the waveform type. The results
will vary somewhat based on actual crest factor and
Figure 19. Settling Time with DC-Accurate Post Filter
Figure 18. Settling Time with Buffered Post Filter
SETTLING TIME (SEC)
0.01
0.1
SETTLING ACCURACY (%)
1
10
10.1 10 100
1967 F18
C = 0.1µF C = 0.22µF C = 0.47µF C = 1µF C = 2.2µF C = 4.7µF C = 10µF C = 22µF C = 47µF C = 100µF
C = 220µF
SETTLING TIME (SEC)
0.01
0.1
SETTLING ACCURACY (%)
1
10
10.1 10 100
1967 F19
C = 0.1µF C = 0.22µF C = 0.47µF C = 1µF C = 2.2µF C = 4.7µF C = 10µFC = 22µFC = 47µF C = 100µF
C = 220µF
19
LTC1967
1967f
waveform dynamics and the type of filtering used. The
above method is conservative for some cases and about
right for others.
The LTC1967 works well with signals whose crest factor
is 4 or less. At higher crest factors, the internal ∆Σ
modulator will saturate, and results will vary depending on
the exact frequency, shape and (to a lesser extent) ampli-
tude of the input waveform. The output voltage could be
higher or lower than the actual RMS of the input signal.
The ∆Σ modulator may also saturate when signals with
crest factors less than 4 are used with insufficient averag-
ing. This will only occur when the output droops to less
than 1/4 of the input voltage peak. For instance, a DC-
coupled pulse train with a crest factor of 4 has a duty cycle
of 6.25% and a 1V
PEAK
input is 250mV
RMS
. If this input is
50Hz, repeating every 20ms, and C
AVE
= 1µF, the output
will droop during the inactive 93.75% of the waveform.
This droop is calculated as:
VVe
MIN RMS INACTIVE TIME
=
−
21–
2 • Z • C
OUT AVE
For the LTC1967, whose output impedance (Z
OUT
) is
50kΩ, this droop works out to –8.54%, so the output
would be reduced to 229mV at the end of the inactive
portion of the input. When the input signal again climbs to
1V
PEAK
, the peak/output ratio is 4.36.
With C
AVE
= 10µF, the droop is only –0.929% to 247.7mV
and the peak/output ratio is just 4.038, which the LTC1967
has enough margin to handle without error.
For crest factors less than 3.5, the selection of C
AVE
as
previously described should be sufficient to avoid this
droop and modulator saturation effect. But with crest
factors above 3.5, the droop should also be checked for
each design.
Error Analyses
Once the RMS-to-DC conversion circuit is working, it is
time to take a step back and do an analysis of the accuracy
of that conversion. The LTC1967 specifications include
three basic static error terms, V
OOS
, V
IOS
and GAIN. The
output offset is an error that simply adds to (or subtracts
APPLICATIO S I FOR ATIO
WUUU
from) the voltage at the output. The conversion gain of the
LTC1967 is nominally 1.000 V
DCOUT
/V
RMSIN
and the gain
error reflects the extent to which this conversion gain is
not perfectly unity. Both of these affect the results in a
fairly obvious way.
Input offset on the other hand, despite its conceptual
simplicity, effects the output in a nonobvious way. As its
name implies, it is a constant error voltage that adds
directly with the input. And it is the sum of the input and
V
IOS
that is RMS converted.
This means that the effect of V
IOS
is warped by the
nonlinear RMS conversion. With 0.2mV (typ) V
IOS
, and a
200mV
RMS
AC input, the RMS calculation will add the DC
and AC terms in an RMS fashion and the effect is
negligible:
V
OUT
= √(200mV AC)
2
+ (0.2mV DC)
2
= 200.0001mV
= 200mV + 1/2ppm
But with 10× less AC input, the error caused by V
IOS
is
100× larger:
V
OUT
= √(20mV AC)
2
+ (0.2mV DC)
2
= 20.001mV
= 20mV + 50ppm
This phenomena, although small, is one source of the
LTC1967’s residual nonlinearity.
On the other hand, if the input is DC coupled, the input
offset voltage adds directly. With +200mV and a +0.2mV
V
IOS
, a 200.2mV output will result, an error of 0.1% or
1000ppm. With DC inputs, the error caused by V
IOS
can be
positive or negative depending if the two have the same or
opposing polarity.
The total conversion error with a sine wave input using the
typical values of the LTC1967 static errors is computed as
follows:
V
OUT
= (√(500mV AC)
2
+ (0.2mV DC)
2
) • 1.001 + 0.1mV
= 500.600mV
= 500mV + 0.120%
V
OUT
= (√(50mV AC)
2
+ (0.2mV DC)
2
) • 1.001 + 0.1mV
= 50.150mV
= 50mV + 0.301%
20
LTC1967
1967f
V
OUT
= (√(5mV AC)
2
+ (0.2mV DC)
2
) • 1.001 + 0.1mV
= 5.109mV
= 5mV + 2.18%
As can be seen, the gain term dominates with large inputs,
while the offset terms become significant with smaller
inputs. In fact, 5mV is the minimum RMS level needed to
keep the LTC1967 calculation core functioning normally,
so this represents the worst-case of usable input levels.
Using the worst-case values of the LTC1967 static errors,
the total conversion error is:
V
OUT
= ( √(500mV AC)
2
+ (1.5mV DC)
2
) • 1.003 + 0.55mV
= 502.05mV
= 500mV + 0.41%
V
OUT
= (√(50mV AC)
2
+ (1.5mV DC)
2
) • 1.003 + 0.55mV
= 50.723mV
= 50mV + 1.45%
V
OUT
= (√(5mV AC)
2
+ (1.5mV DC)
2
) • 1.003 + 0.55mV
= 5.786mV
= 5mV + 15.7%
These static error terms are in addition to dynamic error
terms that depend on the input signal. See the Design
Cookbook for a discussion of the DC conversion error with
low frequency AC inputs. The LTC1967 bandwidth limita-
tions cause additional errors with high frequency inputs.
Another dynamic error is due to crest factor. The LTC1967
performance versus crest factor is shown in the Typical
Performance Characteristics.
Output Errors Versus Frequency
As mentioned in the design cookbook, the LTC1967 per-
forms very well with low frequency and very low frequency
inputs, provided a large enough averaging capacitor is used.
However, the LTC1967 will have additional dynamic errors
as the input frequency is increased. The LTC1967 is de-
signed for high accuracy RMS-to-DC conversion of sig-
nals beyond the audible range. The input sampling ampli-
fiers have a –3dB frequency of 2MHz or so. However, the
switched capacitor circuitry samples the inputs at a mod-
est 500kHz nominal. The response versus frequency is
APPLICATIO S I FOR ATIO
WUUU
depicted in the Typical Performance Characteristics titled
Input Signal Bandwidth. Although there is a pattern to the
response versus frequency that repeats every sample fre-
quency, the errors are not overwhelming. This is because
LTC1967 RMS calculation is inherently wideband, operat-
ing properly with minimal oversampling, or even
undersampling, using several proprietary techniques to
exploit the fact that the RMS value of an aliased signal is
the same as the RMS value of the original signal. However,
a fundamental feature of the ∆Σ modulator is that sample
estimation noise is shaped such that minimal noise occurs
with input frequencies much less than the sampling fre-
quency, but such noise peaks when input frequency reaches
half the sampling frequency. Fortunately the LTC1967
output averaging filter greatly reduces this error, but the
RMS-to-DC topology frequency shifts the noise to low
(baseband) frequencies. See Output Noise vs Input Fre-
quency in the Typical Performance Characteristics.
Input Impedance
The LTC1967 true RMS-to-DC converter utilizes a 0.8pF
capacitor to sample the input at a nominal 500kHz sample
frequency. This accounts for the 5MΩ input impedance.
See Figure 20 for the equivalent analog input circuit. Note
however, that the 5MΩ input impedance does not directly
affect the input sampling accuracy. For instance, if a 62k
source resistance is used to drive the LTC1967, the
sampling action of the input stage will drag down the
voltage seen at the input pins with small spikes at every
sample clock edge as the sample capacitor is connected to
be charged. The time constant of this combination is
small, 0.8pF • 62kΩ = 50ns, and during the 500ns period
Figure 20. LTC1967 Equivalent Analog Input Circuit
IN1
V
DD
V
DD
V
SS
V
SS
R
SW
(TYP)
2k
C
EQ
0.8pF
(TYP)
C
EQ
0.8pF
(TYP)
I
IN1
IN2
I
IN2
1967 F20
R
SW
(TYP)
2k
IIN VV
R
IIN VV
R
RM
AVG
IN IN
EQ
AVG
IN IN
EQ
EQ
1
2
5
12
21
()
=−
()
=−
=
Ω
21
LTC1967
1967f
APPLICATIO S I FOR ATIO
WUUU
devoted to sampling, ten time constants elapse. This
allows each sample to settle to within 46ppm and it is these
samples that are used to compute the RMS value.
This is a much higher accuracy than the LTC1967 conver-
sion limits, and far better than the accuracy computed via
the simplistic resistive divider model:
Output Impedance
The LTC1967 output impedance during operation is simi-
larly due to a switched capacitor action. In this case, 20pF
of on-chip capacitance operating at 500kHz translates into
100kΩ. The closed-loop RMS-to-DC calculation cuts that
in half to the nominal 50kΩ specified.
In order to create a DC result, a large averaging capacitor
is required. Capacitive loading and time constants are not
an issue on the output.
However, resistive loading is an issue and the 10MΩ
impedance of a DMM or 10× scope probe will drag the
output down by –0.5% typ.
During shutdown, the switching action is halted and a
fixed 50k resistor shunts V
OUT
to OUT RTN so that C
AVE
is
discharged.
Interfacing with an ADC
The LTC1967 output impedance and the RMS averaging
ripple need to be considered when using an analog-to-
digital converter (ADC) to digitize the LTC1967 RMS
result.
The simplest configuration is to connect the LTC1967
directly to the input of a type 7106/7136 ADC as shown in
Figure 21a. These devices are designed specifically for
DVM/DPM use and include display drivers for a 3 1/2 digit
LCD segmented display. Using a dual-slope conversion,
the input is sampled over a long integration window, which
results in rejection of line frequency ripple when integra-
tion time is an integer number of line cycles. Finally, these
parts have an input impedance in the GΩ range, with
specified input leakage of 10pA to 20pA. Such a leakage,
combined with the LTC1967 output impedance, results in
just 1µV to 2µV of additional output offset voltage.
Another type of ADC that has inherent rejection of RMS
averaging ripple is an oversampling ∆Σ ADC such as the
LTC2420. Its input impedance is 6.5MΩ, but only when it
is sampling. Since this occurs only half the time at most,
if it directly loads the LTC1967, a gain error of –0.32% to
–0.43% results. In fact, the LTC2420 DC input current is
VV R
RR
VM
Mk
V
IN SOURCE IN
IN SOURCE
SOURCE
SOURCE
=+
=Ω
Ω+ Ω
=
5
562
125–. %
This resistive divider calculation does give the correct
model of what voltage is seen at the input terminals by a
parallel load averaged over a several clock cycles, which is
what a large shunt capacitor will do—average the current
spikes over several clock cycles.
When high source impedances are used, care must be taken
to minimize shunt capacitance at the LTC1967 input so as
not to increase the settling time. Shunt capacitance of just
0.8pF will double the input settling time constant and the
error in the above example grows from 46ppm to 0.67%
(6700ppm). As a consequence, it is important to
not
try to
filter the input with large input capacitances unless driven
by a low impedance. Keep time constant <<500ns.
When the LTC1967 is driven by op amp outputs, whose
low DC impedance can be compromised by sharp capaci-
tive load switching, a small series resistor may be added.
A 1k resistor will easily settle with the 0.8pF input sampling
capacitor to within 1ppm.
These are important points to consider both during design
and debug. During lab debug, and even production testing,
a high value series resistor to any test point is advisable.
22
LTC1967
1967f
not zero at 0V, but rather at one half its reference, so both
an output offset and a gain error will result. These errors
will vary from part to part, but with a specific LTC1967 and
LTC2420 combination, the errors will be fixed, varying less
than ±0.05% over temperature. So a system that has digi-
tal calibration can be quite accurate despite the nominal
gain and offset error. With 20 bits of resolution, this part
is more accurate than the LTC1967, but the extra resolu-
tion is helpful because it reduces nonlinearity at the LSB
transitions as a digital gain correction is made. Further-
more, its small size and ease of use make it attractive.
This connection is shown in Figure 21b, where the LTC2420
is set to continuously convert by grounding the CS pin. The
gain error will be less if CS is driven at a slower rate,
however, the rate should either be consistent or at a rate
low enough that the LTC1967 and its output capacitor have
fully settled by the beginning of each conversion, so that
the loading errors are consistent.
Other types of ADCs sample the input signal once and
perform a conversion on that one sample. With these
ADCs (Nyquist ADCs), a post filter will be needed in most
cases to reduce the peak error with low input frequencies.
The DC-accurate filter of Figure 13 is attractive from an
error standpoint, but it increases the impedance at the ADC
input. In most cases, the buffered post filter of Figure␣ 12
will be more appropriate for use with Nyquist analog-to-
digital converters.
SYSTEM CALIBRATION
The LTC1967 static accuracy can be improved with end-
system calibration. Traditionally, calibration has been
done at the factory, or at a service depot only, typically
using manually adjusted potentiometers. Increasingly,
systems are being designed for electronic calibration
where the accuracy corrections are implemented in digital
code wherever possible, and with calibration DACs where
necessary. Additionally, many systems are now designed
for self calibration, in which the calibration occurs inside
the machine, automatically without user intervention.
Whatever calibration scheme is used, the linearity of the
LTC1967 will improve the calibrated accuracy over that
achievable with older log/antilog RMS-to-DC converters.
Additionally, calibration using DC reference voltages are
essentially as accurate with the LTC1967 as those using
AC reference voltages. Older log/antilog RMS-to-DC con-
verters required nonlinear input stages (rectifiers) whose
linearity would typically render DC-based calibration
unworkable.
The following are four suggested calibration methods.
Implementations of the suggested adjustments are de-
pendent on the system design, but in many cases, gain and
output offset can be corrected in the digital domain, and
will include the effect of all gains and offsets from the
LTC1967 output through the ADC. Input offset voltage, on
the other hand, will have to be corrected with adjustment
to the actual analog input to the LTC1967.
AC-Only, 1 Point
The dominant error at full scale will be caused by the gain
error, and by applying a full-scale sine wave input, this
error can be measured and corrected for. Unlike older log/
antilog RMS-to-DC converters, the correction should be
made for zero error at full scale to minimize errors through-
out the dynamic range.
The best frequency for the calibration signal is roughly ten
times the –0.1% DC error frequency. For 1µF, –0.1% DC
error occurs at 10Hz, so 100Hz is a good calibration
frequency, although anywhere from 60Hz to 100Hz should
suffice.
APPLICATIO S I FOR ATIO
WUUU
Figure 21a. Interfacing to DVM/DPM ADC
Figure 21b. Interfacing to LTC2420
C
AVE
LTC1967
OUTPUT
OUT RTN
7106 TYPE
IN HI
IN LO
5
6
31
1967 F21a
30
CAVE
LTC1967
OUTPUT
OUT RTN
LTC2420
VIN SERIAL
DATA
DIGITALLY CORRECT
LOADING ERRORS
GND
SDO
SCK
CS
5
6
3
1967 F21b
4
23
LTC1967
1967f
The trade-off here is that on the one hand, the DC error is
input frequency dependent, so a calibration signal fre-
quency high enough to make the DC error negligible
should be used. On the other hand, as low a frequency as
can be used is best to avoid attenuation of the calibrated
AC signal, either from parasitic RC loading or insufficient
op amp gain. For instance, with a 1kHz calibration signal,
a 1MHz op amp will typically only have 60dB of open-loop
gain, so it could attenuate the calibration signal a full 0.1%.
AC-Only, 2 Point
The next most significant error for AC-coupled applica-
tions will be the effect of output offset voltage, noticeable
at the bottom end of the input scale. This too can be
calibrated out if two measurements are made, one with a
full-scale sine wave input and a second with a sine wave
input (of the same frequency) at 10% of full scale. The
trade-off in selecting this second level is that it should be
small enough that the gain error effect becomes small
compared to the gain error effect at full scale, while on the
other hand, not using so small an input that the input offset
voltage becomes an issue.
The calculations of the error terms for a 200mV full-scale
case are:
Gain = Reading at 200mV – Reading at 20mV
180mV
Output Offset = Reading at 20mV
Gain –20mV
DC, 2 Point
DC-based calibration is preferable in many cases because
a DC voltage of known, good accuracy is easier to gener-
ate than such an AC calibration voltage. The only down
side is that the LTC1967 input offset voltage plays a role.
It is therefore suggested that a DC-based calibration
scheme check at least two points: ±full scale. Applying the
–full-scale input can be done by physically inverting the
voltage or by applying the same +full-scale input to the
opposite LTC1967 input.
For an otherwise AC-coupled application, only the gain
term may be worth correcting for, but for DC-coupled
applications, the input offset voltage can also be calcu-
lated and corrected for.
The calculations of the error terms for a 200mV full-scale
case are:
Gain = Reading at 200mV +Reading at – 200mV
400mV
Input Offset = Reading at – 200mV – Reading at 200mV
2•Gain
Note: Calculation of and correction for input offset voltage
are the only way in which the two LTC1967 inputs (IN1,
IN2) are distinguishable from each other. The calculation
above assumes the standard definition of offset; that a
positive offset is the case of a positive voltage error inside
the device that must be corrected by applying a like
negative voltage outside. The offset is referred to which-
ever pin is driven positive for the +full-scale reading.
DC, 3 Point
One more point is needed with a DC calibration scheme to
determine output offset voltage: +10% of full scale.
The calculation of the input offset is the same as for the
2-point calibration above, while the gain and output offset
are calculated for a 200mV full-scale case as:
Gain = Reading at 200mV – Reading at 20mV
180mV
Output Offset =
Reading at 200mV +Reading at – 200mV – 400mV •Gain
2
APPLICATIO S I FOR ATIO
WUUU
24
LTC1967
1967f
APPLICATIO S I FOR ATIO
WUUU
TROUBLESHOOTING GUIDE
Top Ten LTC1967 Application Mistakes
1. Circuit won’t work–Dead On Arrival–no power drawn.
– Probably forgot to enable the LTC1967 by pulling
Pin␣ 8 low.
Solution: Tie Pin 8 to Pin 1.
2. Circuit won’t work, but draws power. Zero or very
little output, single-ended input application.
– Probably didn’t connect both input pins.
Solution: Tie both inputs to something. See “Input
Connections” in the Design Cookbook.
4. Gain is low by a few percent, along with other screwy
results.
– Probably tried to use output in a floating, differential
manner.
Solution: Tie Pin 6 to a low impedance. See “Output
Connections” in the Design Cookbook.
LTC1967
CONNECT PIN 3
IN1
2
3
NC IN2
1967TS02
LTC1967
IN1
2
3IN2
1967 TS03
DC-COUPLE ONE INPUT
LTC1967
DC-CONNECT ONE INPUT
IN1
2
3IN2
3. Screwy results, particularly with respect to linearity
or high crest factors; differential input application.
– Probably AC-coupled both input pins.
Solution: Make at least one input DC-coupled. See
“Input Connections” in the Design Cookbook.
TYPE 7136
ADC
LTC1967
HI
31
30
5
6LO
V
OUT
OUT RTN
1967 TS04
GROUND PIN 6
5. Offsets perceived to be out of specification because 0V
in ≠ 0V out.
– The offsets are not specified at 0V in. No RMS-to-
DC converter works well at 0 due to a divide-by-zero
calculation.
Solution: Measure V
IOS
/V
OOS
by extrapolating read-
ings > ±5mV
DC
.
6. Linearity perceived to be out of specification particu-
larly with small input signals.
– This could again be due to using 0V in as one of the
measurement points.
Solution: Check Linearity from 5mV
RMS
to
500mV
RMS
.
–
The input offset voltage can cause small AC linear
ityerrors at low input amplitudes as well. See “Error
Analyses” section.
Possible Solution: Include a trim for input offset.
25
LTC1967
1967f
APPLICATIO S I FOR ATIO
WUUU
7. Output is noisy with >50kHz inputs.
– This is a fundamental characteristic of this topol-
ogy. The LTC1967 is designed to work very well
with inputs of 20kHz or less. It works okay as high
as1MHz, but it is limited by aliased ∆Σ noise.
Solution: Bandwidth limit the input or digitally filter
the resulting output.
8. Large errors occur at crest factors approaching, but
less than 4.
– Insufficient averaging.
Solution: Increase C
AVE
. See “Crest Factor and AC +
DC Waveforms” section for discussion of output
droop.
9. Screwy results, errors > spec limits, typically 1% to 5%.
– High impedance (50kΩ) and high accuracy (0.1%)
require clean boards! Flux residue, finger grime, etc.
all wreak havoc at this level.
Solution: Wash the board.
10. Gain is low by ≅1% or more, no other problems.
– Probably due to circuit loading. With a DMM or a
10× scope probe, Z
IN
= 10MΩ. The LTC1967
output is 50kΩ, resulting in –0.5% gain error.
Output impedance is higher with the DC accurate
post filter.
Solution: Remove the shunt loading or buffer the
output.
– Loading can also be caused by cheap averaging
capacitors.
Solution: Use a high quality metal film capacitor
for C
AVE
.
LTC1967
KEEP BOARD CLEAN
1967 TS09
200mVRMS IN
–0.5%
DMM
DCV
LTC1967
10M
5
50k 6
VOUT
OUT RTN
1967 TS10
LOADING DRAGS DOWN GAIN
mV
26
LTC1967
1967f
TYPICAL APPLICATIO S
U
SI PLIFIED SCHE ATIC
WW
5V Single Supply, Differential,
AC-Coupled RMS-to-DC Converter Single Supply RMS Current Measurement
V
+
5V
LTC1967
IN1 DC OUTPUT
C
AVE
1µF
C
C
0.1µF
IN2
1967 TA02
V
OUT
AC INPUTS
(1V
PEAK
DIFFERENTIAL) OUT RTN
GND EN
V+
LTC1967
IN1
VOUT = 4mVDC/ARMS
CAVE
1µF
0.1µF
IN2
1967 TA03
VOUT
AC CURRENT
75A MAX
50Hz TO 400Hz OUT RTN
GND EN
20k
20k
10Ω
T1: CR MAGNETICS CR8348-2500-N
www.crmagnetics.com
T1
2nd ORDER ∆Σ MODULATOR
IN1
IN2
EN
V
+
–
+
–
+
OUTPUT
OUT RTN
50k
BLEED RESISTOR
FOR C
AVE
C
AVE
1967 SS
TO BIAS CONTROL
GND
∫
∫
C1
C2
Y1 Y2
C12
C11
CLOSED
DURING
SHUTDOWN
C9
C10
C5C3
C4
C6
C8
C7
A2A1
27
LTC1967
1967f
U
PACKAGE DESCRIPTIO
MS8 Package
8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660)
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
MSOP (MS8) 0204
0.53 ± 0.152
(.021 ± .006)
SEATING
PLANE
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.18
(.007)
0.254
(.010)
1.10
(.043)
MAX
0.22 – 0.38
(.009 – .015)
TYP
0.127 ± 0.076
(.005 ± .003)
0.86
(.034)
REF
0.65
(.0256)
BSC
0° – 6° TYP
DETAIL “A”
DETAIL “A”
GAUGE PLANE
12
34
4.90 ± 0.152
(.193 ± .006)
8765
3.00 ± 0.102
(.118 ± .004)
(NOTE 3)
3.00 ± 0.102
(.118 ± .004)
(NOTE 4)
0.52
(.0205)
REF
5.23
(.206)
MIN
3.20 – 3.45
(.126 – .136)
0.889 ± 0.127
(.035 ± .005)
RECOMMENDED SOLDER PAD LAYOUT
0.42 ± 0.038
(.0165 ± .0015)
TYP
0.65
(.0256)
BSC
TYPICAL APPLICATIO S
U
±2.5V Supplies, Single Ended, DC-Coupled
RMS-to-DC Converter with Shutdown RMS Noise Measurement
V
+
2.5V
–2.5V
–2.5V
LTC1967
IN1 DC OUTPUT
C
AVE
1µF
0.1µF
X7R
IN2
1967 TA04
V
OUT
DC + AC
INPUT
(1V
PEAK
)OUT RTN
GND
EN
OFF
≥2V ≤–2V
ON V
+
2.5V
–2.5V
2.5V
–2.5V
LTC1967
IN1 C
AVE
1µF
0.1µF
1.5µF
IN2
1967 TA05
V
OUT
VOLTAGE
NOISE IN
OUT RTN
GND EN
1mV
DC
1µV
RMS
NOISE
V
OUT
=
–
+
1k
100Ω
100Ω100k
BW ≈ 1kHz TO 100kHz
INPUT SENSITIVITY = 1µV
RMS
TYP
1/2
LTC6203
28
LTC1967
1967f
LINEAR TECHNOLOGY CORPORATION 2004
LT/TP 0504 1K • PRINTED IN USA
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507
●
www.linear.com
RELATED PARTS
PART NUMBER DESCRIPTION COMMENTS
LT®1077 Micropower, Single Supply Precision Op Amp 48µA I
SY
, 60µV V
OS(MAX)
, 450pA I
OS(MAX)
LT1175-5 Negative, –5V Fixed, Micropower LDO Regulator 45µA I
Q
, Available in SO-8 or SOT-223
LT1494 1.5µA Max, Precision Rail-to-Rail I/O Op Amp 375µV V
OS(MAX)
, 100pA I
OS(MAX)
LT1782 General Purpose SOT-23 Rail-to-Rail Op Amp 40µA I
SY
, 800µV V
OS(MAX)
, 2nA I
OS(MAX)
LT1880 SOT-23 Rail-to-Rail Output Precision Op Amp 1.2mA I
SY
, 150µV V
OS(MAX)
, 900pA I
OS(MAX)
LTC2054 Zero Drift Op Amp in SOT-23 150µA I
SY
, 3µV V
OS(MAX)
, 150pA I
B(MAX)
LT2178/LT2178A 17µA Max, Single Supply Precision Dual Op Amp 14µA I
SY
, 120µV V
OS(MAX)
, 350pA I
OS(MAX)
LTC1966 Precision Micropower ∆Σ RMS-to-DC Converter 155µA I
SY
LTC2402 2-Channel, 24-bit, Micropower, No Latency ∆ΣTM ADC 200µA I
SY
, 4ppm INL, 10ppm TUE
LTC2420 20-bit, Micropower, No Latency ∆Σ ADC in SO-8 200µA I
SY
, 8ppm INL, 16ppm TUE
LTC2422 2-Channel, 20-bit, Micropower, No Latency ∆Σ ADC Dual channel version of LTC2420
No Latency ∆Σ is a trademark of Linear Technology Corporation.
Audio Amplitude Compressor
TYPICAL APPLICATIO
U
–
+
–
+
–
+
8
7
9
2
1
14
R4
2.49k
R1
100k
V
IN
R3
7.5k
R5
5.9k
R15
47Ω
V
FS
R2
1k
C2
0.47µF
C1
47nF
13
A1
A2
V
+
LT1256
V
–
V
+
V
OUT
C3
0.1µF
R13
3.3k
R14
3.3k
12
R
FS
10
R
C
5
V
C
R6
2k
R10
200k R12
10k
R9
10k
R8
15k
V
+
LT1636
ATTENUATION CONTROL
GAIN OF 4
ATTENUATE
BY 1/4
V
+
V
–
R7
5.9k
3
C5
0.22µFC4
0.33µF
LTC1967
V
S
= ±5V
1967 TA07
V
DD
GND EN
V
OUT
OUT RTN
IN1
IN2
0.1µF
