XPM6 Miniature pressure sensor Sealed and gauge ranges 100 to 1000 bars [1500 to 15000 psi] Stainless steel housing High level output in option For static and dynamic applications Linearity 0.25% F.S. DESCRIPTION The XPM6 is a miniature transducer designed to measure static and dynamic pressure under a wide variety of conditions, including hostile environments. It is made of stainless steel and is available in ranges from 0-100 to 0-1000 bar [1500 to 15 000 psi]. For protection against thermal flash/explosive testing up to 1000 C [1832 F] the option MH allows inserting extra protection into the "H" shape diaphragm. The XPM6 incorporates Measurement Specialties' cutting edge SanShift zero shifts caused by installation torque. TM technology, which virtually eliminates The XPM6's sensing element is a fully temperature compensated Wheatstone bridge made with high stability micromachined silicon strain gauges. With many years of experience as a designer and manufacturer of sensors, Measurement Specialties, Inc. has the expertise to customize and/or design sensors for specific uses and testing environments. To meet your needs we also offer complete turnkey systems. Our conditioning electronics can power the sensor, amplify the electronic signal, and display the data digitally. A turnkey measurement system arrives with matched components, formatted, calibrated and ready for your immediate use. FEATURES APPLICATIONS M6x1 thread Flush Diaphragm For Static and Dynamic Applications High Level Tension Output Available Low Installation Torque Sensitivity Explosion test benches Extreme Miniature Devices Robotics and actuators Breaking system pressure Laboratory and research STANDARD RANGES Range in bar Range in psi XPM6_en_revB 0-100 0-1500 0-200 0-3000 www.meas-spec.com 1/4 0-500 0-7500 0-1000 0-15000 2012-11-30 XPM6 Miniature pressure sensor CHARACTERISTICS All values are typical at temperature 201C Parameters Operating Temperature Range (OTR) -40 to 150 C [-40 to 302 F] Without A1 option -40 to 120 C [-40 to 248 F] With A1 option Compensated Temperature Range (CTR) 0 to 60 C [32 to 140 F] Zero Shift in CTR <2.5% F.S./50 C [/100 F] Sensitivity Shift in CTR <2% of reading /50 C [/100 F] Range (F.S.) See standard ranges table Tightening Torque Nominal (zero and sensitivity shift <1%) Maximal 5 N.m [44 lbf.in] 10 N.m [88 lbf.in] Over-Range Without Damage Without Destruction 2x F.S 3xF.S. Accuracy Linearity 0.25% F.S. Hysteresis 0.25% F.S Repeatability 0.2% F.S Electrical Characteristics Model Supply Voltage F.S. Output 6 XPM6 XPM6-A1 10 Vdc 10 to 30 Vdc 100 mV 4 V 5% F.S. Zero Offset 6 <10 mV 0.5 V 5% F.S. Input Impedance 1500 <25 mA Output Impedance 800 1 k 7 Insulation under 50Vdc 100 M 100 M Notes 1. Electrical Termination: Shielded O3 mm cable with 4 wires (AWG30), standard length 2.0 m [6.6 ft] with strain relief spring 2. Material: Body and flush diaphragm in stainless steel; laser welded 3. Protection Index: IP50 4. Resonance Frequency: 200-750 kHz depending on range 5. O12 mm copper ring, supplied with the sensor 6. Standard output signal, custom outputs < 4V F.S. available on request 7. Output impedance standard, available <100 on request. 8. CE conformance according to EN 61010-1, EN 50081-1, EN 50082-1 XPM6_en_revB www.meas-spec.com 2/4 2012-11-30 XPM6 Miniature pressure sensor DIMENSION & WIRING SCHEMATIC (IN METER AND IMPERIAL) XPM6 XPM6-A1 Custom length L = 12 to 30 mm [0.47" to 1.18"] on request. * Mechanical tolerances on L are 0.1 mm Wiring Schematic XPM6_en_revB www.meas-spec.com 3/4 2012-11-30 XPM6 Miniature pressure sensor OPTIONS G : Gauge S : Sealed Gauge A1 : Amplified Tension output with unipolar power supply MH : "H" Diaphragm for thermal flash/explosive testing HA : Accuracy (CNL&H) 0.25% F.S. SI : Sensitivity shift in CTR 1% of reading / 50 C [/100 F] ZI : Zero shift in CTR 1.5% F.S. / 50 C [/ 100 F] ET1 : CTR -20 to 100 C [-4 to 212 F] ET3 : CTR -40 to 150 C [-40 to 302 F] OTR=CTR (not available with A1 options) L00M : special cable length, replace "00" with total length in meters ORDERING INFORMATION XPM6 - A1 - 1KBS - /L5M Options (L00M, ..) Range in bar (G or S) Power Supply (None, A1) Model NORTH AMERICA EUROPE ASIA Measurement Specialties, Inc. Vibration Design Center 32 Journey - Suite 150 Aliso Viejo, CA 92656 United States USA Tel: 1-949-716-0877 Fax: 1-949-916-5677 t&m@meas-spec.com Measurement Specialties (Europe), Ltd. 26 Rue des Dames 78340 Les Clayes-Sous-Bois, France Tel: +33 (0) 130 79 33 00 Fax: +33 (0) 134 81 03 59 Measurement Specialties (China), Ltd. No. 26 Langshan Road Shenzhen High-Tech Park (North) Nanshan District, Shenzhen 518057 China Tel: +86 755 3330 5088 Fax: +86 755 3330 5099 cs.lcsb@meas-spec.com pfg.cs.asia@meas-spec.com The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the right to make changes without further notice to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer's technical experts. Measurement Specialties, Inc. does not convey any license under its patent rights nor the rights of others. XPM6_en_revB www.meas-spec.com 4/4 2012-11-30 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TE Connectivity: EXPM6-1KBS-S2001