19-3302; Rev 1; 1/11 +48V Quad Hot-Swap Controllers For Power-Over-LAN o Wide Operating Input Voltage Range: +35V to +72V o IEEE(R) 802.3af Compatible o Four Independent Power Switch Controllers o Open-Circuit Detector o On-Board Charge Pumps to Drive External n-Channel FETs o Current Sense with External Resistor o Foldback Current Limiting o +32V Input Undervoltage Lockout o On-Chip +12V, 100mA Voltage Relay Drivers Ordering Information TEMP RANGE PIN-PACKAGE MAX5913AEMH+ PART -40C to +85C 44 MQFP MAX5913AEMH+T -40C to +85C 44 MQFP MAX5914AEMH+ -40C to +85C 44 MQFP MAX5914AEMH+T -40C to +85C 44 MQFP +Denotes a lead(Pb)-free/RoHS-compliant package. T = Tape and reel. 34 35 36 37 38 39 40 41 42 TOP VIEW 43 VDD RTIM ON4 RLYON4 ON3 RLYON3 ON2 RLYON2 ON1 RLYON1 DC Pin Configuration 44 The MAX5913A/MAX5914A are quadruple hot-swap controllers. The MAX5913A/MAX5914A independently control four external n-channel switches to hot-swap system loads from a single VCC supply line. The devices allow the safe insertion and removal of power devices from live network ports. The operating supply voltage range is between +35V and +72V. The devices are intended for applications in Power-Over-Media-Dependent Interface (MDI), but are not limited to such usage. The MAX5913A/MAX5914A feature an internal undervoltage lockout (UVLO) function that prevents the FET from turning on, if VCC does not exceed the default value of +32V. The devices also feature a +12V relay driver with 100mA current drive capable of driving lowvoltage +3.3V relays. The MAX5913A features an active-low relay driver that sinks current when the relay output is enabled. The MAX5914A features an activehigh relay driver output that sources 1mA to drive an external FET relay driver when the relay output is enabled. Control circuitry ensures the relays and the FETs are off until VCC reaches the UVLO threshold. The MAX5913A/MAX5914A use an external sense resistor to enable all the internal current-sense functions. The MAX5913A/MAX5914A feature a programmable analog current-limit circuit. If the switch remains in current limit for more than a programmable time, the n-channel FET latches off and the supply can be restarted either by autoretry or by an external command after the preset offtime has elapsed. The MAX5913A/MAX5914A are available in a 44-pin MQFP package and are specified for the extended -40C to +85C operating temperature range. Features + 4 30 STAT4 CSP4 DRAIN4 5 29 28 CSP1 27 OUT4 GATE4 8 26 9 25 CSP3 DRAIN3 10 24 DRAIN1 GATE1 OUT1 CSP2 11 23 DRAIN2 IEEE is a registered service mark of the Institute of Electrical and Electronics Engineers, Inc. 22 21 OUT3 GATE3 VRLY RLYD3 RLYD4 DGND RLYD1 RLYD2 AGND OUT2 GATE2 Typical Operating Circuit appears at end of data sheet. 20 7 19 MAX5913A MAX5914A 6 12 Midspan Power-Over-MDI STAT3 STATOUT OCEN DGND VCC 18 Network Switches/Routers 31 17 Telecom Line Cards 3 16 IP Phone Switches/Routers RTRYEN 32 15 Power-Over-MDI 33 2 14 Power-Over-LAN 1 13 Applications FAULT STAT1 STAT2 MQFP ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX5913A/MAX5914A General Description MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN ABSOLUTE MAXIMUM RATINGS VCC to AGND or DGND..........................................-0.6V to +76V DRAIN_, OUT_ to AGND or DGND .............-0.6V to (VCC +0.3V) CSP_ to VCC ..........................................................-0.3V to +0.3V GATE_ to OUT_ .....................................................-0.3V to +13V VRLY to DGND ........................................................-0.3V to +18V RLYD_ to DGND........................................-0.3V to (VRLY + 0.3V) ON_, RLYON_, OCEN, RTRYEN, STATOUT, DC to DGND........................................................-0.3V to +12V FAULT to DGND .....................................................-0.3V to +12V STAT_, RTIM to DGND ...............................-0.3V to (VDD + 0.3V) VDD to DGND ...........................................................-0.3V to +7V DGND to AGND...........................................................-5V to +5V Current into RLYD_ .........................................-50mA to +150mA Current into Any Other Pin................................................50mA Continuous Power Dissipation (TA = +70C) 44-Pin MQFP (derate 12.7mW/C above +70C)......... 1.013W Operating Temperature Range ...........................-40C to +85C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) ................................ +300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = VCSP_ = +48V, VAGND = VDGND = 0V, VDD = +3.3V, VRLY = +12V, TA = -40C to +85C, unless otherwise noted. Typical values are at VCC = VCSP_ = +48V and TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 72 V POWER SUPPLIES Analog Supply Voltage VCC Measured with respect to AGND VCC = VCSP_ = 72V IS = ICC + ICSP Analog Supply Current IS Digital Supply Voltage VDD Measured with respect to DGND Digital Supply Current IDD All logic outputs high, RTIM unconnected Analog Supply Undervoltage Lockout VUVLO UVLO Hysteresis VUVLO,H UVLO Deglitch Delay tD,UVLO 35 TA = 0C to +85C 2.7 TA = -40C to 0C VCC rising, circuits enabled 4 5 2.5 29 3.3 3.7 V 1.1 3 mA 32 35 V 3 VON = 3.3V, VRLYON = 3.3V (Figure 1) Relay Driver Supply VRLY Measured with respect to DGND Ground Potential Difference VGG Voltage difference between DGND and AGND 12.8 mA 25.6 -4 V 38.4 ms 14 V 4 V 2 A FEEDBACK INPUT AND CURRENT SENSE OUT Sense Bias Current IFP Initial Feedback Voltage VFB_S Current-Limit Threshold Voltage Foldback Voltage Fast Discharge Threshold Switch-On Threshold Switch-On Comparator Hysteresis VSC VFLBK VOUT_ = VCC Voltage under which the foldback circuit starts reducing the current-limit value (Note 1) Maximum V across RSENSE at VOUT > VFB_S Maximum V across RSENSE at VOUT = 0V VFC VSWON Maximum VCC - VOUT at which the switch is defined as fully on, VOUT increasing 18 125 142.5 V 160 mV 42 48 54 mV 360 420 480 mV 1.2 1.5 1.8 V VSWON_H 160 mV MOSFET DRIVERS Gate Overdrive Voltage Gate Charge Current 2 VGS IGATE VGATE - VCC when switch is fully on 0C to +85C 7 9 11 TA = -40C to 0C 7 9 12 VGATE = 0V 7 10 13 _______________________________________________________________________________________ V A +48V Quad Hot-Swap Controllers For Power-Over-LAN (VCC = VCSP_ = +48V, VAGND = VDGND = 0V, VDD = +3.3V, VRLY = +12V, TA = -40C to +85C, unless otherwise noted. Typical values are at VCC = VCSP_ = +48V and TA = +25C.) PARAMETER Gate Discharge Current Source-Gate Clamp Voltage SYMBOL CONDITIONS MIN TYP MAX UNITS During current regulation 8 A IGATE,DIS VON = 0V (VCSP_ - VDRAIN_) > VFC 1 mA 15 mA VSGZ VOUT_ = 0V, force 30mA into GATE_, measure VGATE - VOUT 14 16.5 18 V VOC Minimum V across RSENSE to detect an open circuit 1.5 3 4.5 mV tOC (Figure 2) 450 900 1350 ms (VCSP_ - VDRAIN__) < VOC (Figure 2) 106 204 302 ms 0.5 V 0.3 0.8 1.3 mA 2 V OPEN-CIRCUIT DETECTOR Open-Circuit Current-Threshold Voltage Delay to Open-Circuit Detect Deglitch Delay tLPFD RELAY DRIVERS Maximum Low Voltage (MAX5913A) VRLOW RLYON = high, IRLYD_ = 100mA Relay Pullup Current (MAX5914A) IRPLUP RLYON = high, VRLYD_ = 0V Clamp Diode Voltage VRCLAMP Relay Output Leakage Force 100mA into RLYD, measure VRLYD VRLY RLYON_ = low, VRLYD_ = VRLY 1 A TIMING Short-Circuit and Startup Timer (Note 2) tO Auto-Retry Duty Cycle RRTIM = 2k On time for continuous RRTIM = 40k overcurrent conditions RRTIM = 4.8 6.4 8.0 76 128 180 3.2 6.4 9.6 DC = logic low 1 DC = logic high 2 DC = unconnected ms % 4 Port Turn-On Delay tON_DEL VON = 3.3V (Figure 3) 12.8 25.6 38.4 ms Relay Turn-Off Delay tOFF_DEL After RLYON_ goes low (Figure 3) 1.6 3.2 4.8 ms DIGITAL INTERFACE DC Pin Input-Voltage High VIH_DC 2.5V VDD 3.7V DC Pin Input-Voltage Low VIL_DC 2.5V VDD 3.7V DC Pin Input Impedance RIN_DC 0.7 x VDD 1 Logic Input High VIH 2.5V VDD 3.7V Logic Input Low VIL 2.5V VDD 3.7V VFL ISINK = 4mA V 0.3 x VDD 1 FAULT High Input Leakage Logic Output-Voltage High VOH STAT_ outputs sourcing 0.5mA Logic Output-Voltage Low VOL STAT_ outputs sinking 0.5mA V k 0.8 x VDD Logic Input Leakage FAULT Output-Voltage Low V 0.3 x VDD V A 0.4 V 1 A VDD - 0.4 mV 0.4 V Note 1: See Typical Operating Characteristics for Current-Limit Foldback, and refer to Current Sensing and Regulation section. Note 2: The resistor at RTIM can range from 2k to 40k. Note 3: Limits are 100% tested at TA = +25C and TA = +85C. Limits at -40C are guaranteed by design and characterization, but are not production tested. _______________________________________________________________________________________ 3 MAX5913A/MAX5914A ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics TA = +25C 3.2 3.0 2.8 2.6 2.4 3.1 VCC = +48V 3.0 VCC = +57V 2.9 30 VCC FALLING 29 28 VCC = +36V 2.5 33 36 39 42 45 48 51 54 57 60 63 66 69 72 27 -40 -15 10 35 60 85 -40 -15 10 35 60 TEMPERATURE (C) TEMPERATURE (C) GATE OVERDRIVE VOLTAGE vs. INPUT VOLTAGE GATE OVERDRIVE VOLTAGE vs. TEMPERATURE STARTUP WAVEFORMS 9.00 85 MAX5913A/14A toc06 9.5 VCC = +72V VCC = +57V GATE OVERDRIVE (V) TA = -40C TA = +25C MAX5913A/14A toc04 INPUT VOLTAGE (V) 9.50 9.25 VCC RISING 2.8 2.6 2.0 31 3.2 2.7 TA = -40C 2.2 VCC = +72V 3.3 MAX5913A/14A toc03 3.4 32 UVLO (V) TA = +85C MAX5913A/14A toc05 SUPPLY CURRENT (mA) 3.6 3.5 3.4 MAX5913A/14A toc02 3.8 SUPPLY CURRENT (mA) 4.0 MAX5913A/14A toc01 (VCSP_ = VCC = +48V, VDD = +3.3V, VRLY = +12V, VAGND = VDGND = 0V, RTIM = open, TA = +25C, unless otherwise specified.) SUPPLY CURRENT SUPPLY CURRENT UNDERVOLTAGE LOCKOUT vs. INPUT VOLTAGE vs. TEMPERATURE vs. TEMPERATURE GATE OVERDRIVE (V) MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN A 0 0 B 0 C 0 D 9.0 VCC = +48V VCC = +36V 8.5 TA = +85C 8.75 8.0 8.50 -40 33 36 39 42 45 48 51 54 57 60 63 66 69 72 -15 10 35 60 4ms/div 85 TEMPERATURE (C) INPUT VOLTAGE (V) TURN-OFF WAVEFORMS A: VON = VRLYON, 5V/div B: VRLYD, 20V/div C: VOUT, 20V/div D: VGATE, 20V/div UVLO TURN-ON DELAY GATE TURN-OFF WAVEFORM MAX5913A/14A toc07 MAX5913A/14A toc09 MAX5913A/14A toc08 A A B 0 A 0 0 0 B B 0 C 0 0 C 0 D D 0 4ms/div A: VON = VRLYON, 5V/div B: VRLYD, 20V/div C: VOUT, 20V/div D: VGATE, 20V/div 4 0 C 0 D 0 4ms/div 10ms/div A: VRLYD, 20V/div B: VRLYON, 5V/div C: VON, 5V/div D: VGATE, 20V/div RLYON = VDD A: VON, 5V/div B: VCC, 10V/div C: VOUT, 50V/div D: VGATE, 50V/div _______________________________________________________________________________________ +48V Quad Hot-Swap Controllers For Power-Over-LAN TURN-ON INTO CAPACITIVE LOAD (CL = 0.47F) MAX5913A/14A toc10 MAX5913A/14A toc12 MAX5913A/14A toc11 A A 0 TURN-ON INTO CAPACITIVE LOAD (CL = 470F) TURN-ON INTO CAPACITIVE LOAD (CL = 47F) B 0 B A 0 C C C 0 0 0 0 0 0 D 0 D 0 10ms/div RLYON = VDD, RRTIM = 40k A: VON, 5V/div B: VGATE, 20V/div C: VOUT, 20V/div D: IOUT, 200mA/div RLYON = VDD, RRTIM = 2k A: VON, 5V/div B: VGATE, 20V/div C: VOUT, 20V/div D: IOUT, 200mA/div CURRENT-LIMIT FOLDBACK (VCC = +36V) 0 CURRENT-LIMIT FOLDBACK (VCC = +57V) CURRENT-LIMIT FOLDBACK (VCC = +48V) MAX5913A/14A toc13 D 0 1ms/div 400s/div RLYON = VDD A: VON, 5V/div B: VGATE, 20V/div C: VOUT, 20V/div D: IOUT, 100mA/div MAX5913A/14A toc15 MAX5913A/14A toc14 A B B 0 A B 0 C A 0 B 0 C C 0 0 0 0 10ms/div RLYON = VDD, RL = 100, RRTIM = 40k, CLOAD = 470F A: VON, 5V/div B: VOUT, 10V/div C: IOUT, 200mA/div 10ms/div RLYON = VDD, RL = 139, RRTIM = 40k, CLOAD = 470F A: VON, 5V/div B: VOUT, 10V/div C: IOUT, 200mA/div 10ms/div RLYON = VDD, RL = 162, RRTIM = 40k, CLOAD = 470F A: VON, 5V/div B: VOUT, 10V/div C: IOUT, 200mA/div _______________________________________________________________________________________ 5 MAX5913A/MAX5914A Typical Operating Characteristics (continued) (VCSP_ = VCC = +48V, VDD = +3.3V, VRLY = +12V, VAGND = VDGND = 0V, RTIM = open, TA = +25C, unless otherwise specified.) MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN Typical Operating Characteristics (continued) (VCSP_ = VCC = +48V, VDD = +3.3V, VRLY = +12V, VAGND = VDGND = 0V, RTIM = open, TA = +25C, unless otherwise specified.) CURRENT-LIMIT FOLDBACK (VCC = +57V) CURRENT-LIMIT FOLDBACK (VCC = +72V) MAX5913A/14A toc17 MAX5913A/14A toc16 A 0 B 0 CURRENT-LIMIT FOLDBACK (VCC = +72V) MAX5913A/14A toc18 A B A 0 B 0 0 C 0 0 0 C 20ms/div RLYON = VDD, RL = OPEN, RRTIM = 40k, CLOAD = 470F A: VON, 5V/div B: VOUT, 10V/div C. IOUT, 200mA/div RLYON = VDD, RL = 200, RRTIM = 40k A: VON, 5V/div B: VOUT, 10V/div C: IOUT, 200mA/div RLYON = VDD, RL = OPEN, RRTIM = 40k, CLOAD = 470F A: VON, 5V/div B: VOUT, 20V/div C: IOUT, 200mA/div SHORT-CIRCUIT RESPONSE (VCC = +48V) OVERCURRENT DELAY (EXPANDED TIME SCALE) OVERCURRENT DELAY C 0 10ms/div 10ms/div MAX5913A/14A toc21 MAX5913A/14A toc20 MAX5913A/14A toc19 A A A 0 0 0 B B 0 B 0 20ms/div RTRYEN = VDD, RLYON = ON = VDD, DC = 4%, RRTIM = 2k, RL = 100 A: VGATE, 20V/div B: IOUT, 200mA/div 6 1ms/div RTRYEN = VDD, RLYON = ON = VDD, DC = DON'T CARE, RRTIM = 2k, RL = 100 A: VGATE, 20V/div B: IOUT, 200mA/div 0 1ms/div ON = RLYON = VDD, RL = 1, RRTIM = 2k A: IOUT, 200mA/div B: VGATE, 20V/div _______________________________________________________________________________________ +48V Quad Hot-Swap Controllers For Power-Over-LAN PEAK SHORT-CIRCUIT RESPONSE (VCC = +48V EXPANDED TIME SCALE) SHORT-CIRCUIT RESPONSE (VCC = +48V EXPANDED TIME SCALE) SHORT-CIRCUIT RESPONSE (VCC = +57V) MAX5913A/14A toc24 MAX5913A/14A toc23 MAX5913A/14A toc22 A A A 0 0 0 B B B 0 0 0 1ms/div 1s/div 40s/div ON = RLYON = VDD, RL = 1, RRTIM = 2k A: IOUT, 200mA/div B: VGATE, 20V/div ON = RLYON = VDD, RL = 1, RRTIM = 2k A: IOUT, 5A/div B: VGATE, 20V/div SHORT-CIRCUIT RESPONSE (VCC = +57V, EXPANDED TIME SCALE) PEAK SHORT-CIRCUIT RESPONSE TIME (VCC = +57V, EXPANDED TIME SCALE) MAX5913A/14A toc25 ON = RLYON = VDD A: IOUT, 200mA/div B: VGATE, 20V/div SHORT-CIRCUIT RESPONSE (VCC = +72V) MAX5913A/14A toc27 MAX5913A/14A toc26 A A A 0 0 0 B B B 0 40s/div ON = RLYON = VDD, RL = 1, RRTIM = 2k A: IOUT, 200mA/div B: VGATE, 20V/div 0 0 1ms/div 1s/div ON = RLYON = VDD, RL = 1, RRTIM = 2k A: IOUT, 5A/div B: VGATE, 20V/div ON = RLYON = VDD A: IOUT, 200mA/div B: VGATE, 50V/div _______________________________________________________________________________________ 7 MAX5913A/MAX5914A Typical Operating Characteristics (continued) (VCSP_ = VCC = +48V, VDD = +3.3V, VRLY = +12V, VAGND = VDGND = 0V, RTIM = open, TA = +25C, unless otherwise specified.) Typical Operating Characteristics (continued) (VCSP_ = VCC = +48V, VDD = +3.3V, VRLY = +12V, VAGND = VDGND = 0V, RTIM = open, TA = +25C, unless otherwise specified.) PEAK SHORT-CIRCUIT RESPONSE TIME (VCC = +72V, EXPANDED TIME SCALE) OPEN-CIRCUIT THRESHOLD vs. INPUT VOLTAGE MAX5913A/14A toc29 MAX5913A/14A toc28 4.0 A A 0 0 B B THRESHOLD VOLTAGE (mV) 3.8 TA = +85C 3.6 3.4 3.2 3.0 2.8 TA = +25C 2.6 TA = -40C 2.4 0 0 MAX5913A/14A toc30 SHORT-CIRCUIT RESPONSE (VCC = +72V, EXPANDED TIME SCALE) 2.2 2.0 1s/div OPEN-CIRCUIT THRESHOLD vs. TEMPERATURE INPUT VOLTAGE (V) tO vs RRTIM OPEN-CIRCUIT GLITCH DELAY MAX5913A/14A toc32 MAX5913A/14A toc31 4.0 3.5 120 100 TA = -40C, +25C, +85C A 0 B 0 3.0 C 0 -40 -15 10 35 TEMPERATURE (C) 60 40 VCC = +36V, +48V, +57V, AND +72V 2.5 tO (ms) 80 2.0 8 33 36 39 42 45 48 51 54 57 60 63 66 69 72 ON = RLYON = VDD, RL = 1, RRTIM = 2k A: IOUT, 5A/div B: VGATE, 50V/div ON = RLYON = VDD, RL = 1, RRTIM = 2k A: IOUT, 200mA/div B: VGATE, 50V/div MAX5913A/14A toc33 40s/div THRESHOLD VOLTAGE (mV) MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN 60 85 20 0 40ms/div ON = RLYON = VDD, STATOUT = LOW A: IOUT, 20mA/div B: VSTAT, 5V/div C: VGATE, 20V/div 0 5 10 15 20 25 RRTIM (k) _______________________________________________________________________________________ 30 35 40 +48V Quad Hot-Swap Controllers For Power-Over-LAN RETRY DUTY CYCLE vs. DC tO vs. INPUT VOLTAGE CHANNEL-TO-CHANNEL CROSSTALK MAX5913A/14A toc34 MAX5913A/14A toc35 125 tO (ms) 100 RRTIM = 40k MAX5913A/14A toc36 A 0 VTEST 5V/div 75 B 0 50 RRTIM = OPEN 25 C RRTIM = 2k VOUT 10mV/div 0 0 1.8 2.1 2.4 2.7 3.0 3.3 3.6 VDD (V) 100ms/div 20s/div VGATE = 20V/div, RRTIM = 2k A: VGATE, 20V/div, DC = UNCONNECTED (4%) B: VGATE, 20V/div, DC = VDD (2%) C: VGATE, 20V/div, DC = GND (1%) SEE FIGURE 4 FOR TEST CIRCUIT Pin Description PIN NAME FUNCTION FAULT Active-Low Fault Output. FAULT is an open-drain output that goes low when a fault is detected on any of the four channels. FAULT is low when an OC (open circuit) is detected, or when the MAX5913A/MAX5914A is in auto-retry caused by an overcurrent condition. When RTRYEN is low, and the channel switch is latched off due to an overcurrent condition, FAULT remains low until ON_ is driven low. 2, 3, 4, 5 STAT1, STAT2, STAT3, STAT4 Status Outputs. STAT_ are push-pull outputs. Depending on the STATOUT pin status, STAT_ flags either the Power-OK_ or Port-OC_ status. Power-OK_ high indicates: a) ON_ input is high. b) The switch port is fully on and startup is completed (VCSP_ - VOUT_) < VSWON. c) Input voltage is above VUVLO. d) Switch is not in current limit. Power-OK_ low indicates a fault with any of the above conditions. Port-OC_ output high indicates that the switch is latched off because the switch current is less than the opencurrent threshold, Port-OC is low otherwise. 6, 10, 24, 28 CSP4, CSP3, CSP2, CSP1 Current-Sense Positive Input. Connect to VCC and place a current-sense resistor from CSP_ to DRAIN_. Use a Kelvin sense trace from a current-sense resistor to CSP_ (see Figure 7). 7, 11, 23, 27 DRAIN4, DRAIN3, DRAIN2, DRAIN1 1 MOSFET Drain Current-Sense Negative Input. Connect to drain of power MOSFET and connect a current-sense resistor from CSP_ to DRAIN_. Use Kelvin sense trace from current-sense resistor to DRAIN_ (see Figure 7). _______________________________________________________________________________________ 9 MAX5913A/MAX5914A Typical Operating Characteristics (continued) (VCSP_ = VCC = +48V, VDD = +3.3V, VRLY = +12V, VAGND = VDGND = 0V, RTIM = open, TA = +25C, unless otherwise specified.) MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN Pin Description (continued) PIN NAME 8, 12, 21, 25 OUT4, OUT3, OUT2, OUT1 9, 13, 22, 26 GATE4, GATE3, GATE2, GATE1 14 VRLY 15, 16, 18, 19 RLYD3, RLYD4, RLYD1, RLYD2 17, 30 DGND Digital Ground. All logic voltages are referred to DGND. The voltage difference between DGND and AGND can be up to 4V. 20 AGND Analog Ground. All analog voltages are referred to AGND. 29 VCC Analog Power Supply. Connect VCC to +35V to +72V power supply. UVLO circuitry turns off the MOSFET switch and relay for VCC < VUVLO. Bypass VCC to AGND with a 1F capacitor. 31 OCEN Open-Circuit Detector Enable Input. Drive OCEN high to enable open-circuit detector, or drive low to disable. When enabled, the open-circuit detector waits for a 900ms delay after Power-OK conditions are met before enabling the open-circuit detector function. 32 STATOUT Status Output Multiplexer (MUX) Control Input. Controls the signal MUX into the STAT_ outputs. Drive STATOUT high to route Power-OK_ status to STAT_ outputs, or drive STATOUT low to route Port-OC_ status to STAT_ outputs. 33 RTRYEN Auto-Retry Enable Input. Drive RTRYEN high to enable auto-retry. Drive RTRYEN low to enable switch latch-off mode. When switch is latched off, a high-to-low transition on the ON_ control input clears the latch. 10 FUNCTION MOSFET Source Output Voltage Sense. Connect to a power MOSFET source through a 100 series resistor. MOSFET Gate Driver Output. The MAX5913A/MAX5914A regulate the gate-drive voltage to (VCC + 9V) to fully turn on the power n-channel MOSFET. GATE_ sources 10A during startup to slowly turn on the MOSFET switch. GATE_ sinks 1mA to turn off the MOSFET switch. Relay Supply-Voltage Input. Referenced to DGND. Relay-Drive Output. For the MAX5913A, RLYD_ sinks 100mA when the relay driver is enabled. For the MAX5914A, RLYD_ sources 1mA when the relay driver is enabled. Duty-Cycle Programming Input. DC sets the minimum off-time after an overcurrent condition latches off the switch. When RTRYEN is high, DC sets the auto-retry duty cycle. Drive DC low for 1% duty cycle, drive DC high for 2%, or leave DC unconnected for 4% duty cycle. 34 DC 35, 37, 39, 41 RLYON1, RLYON2, RLYON3, RLYON4 36, 38, 40, 42 ON1, ON2, ON3, ON4 MOSFET Switch Control Input. Drive ON_ high to enable GATE_ to turn on the MOSFET switch. RLYON_ must be high to enable the switch. Drive ON_ low to disable the switch. Pulling ON_ low also resets the latch when RTRYEN is low or if the switch is latched off due to open-circuit detection. 43 RTIM Timing Oscillator Frequency Set Input. Connect a 2k to 40k resistor from RTIM to DGND to set the maximum continuous overcurrent time, tO. Leave RTIM unconnected to set default 6.4ms tO. 44 VDD Digital Power Supply. Bypass VDD to DGND with a 1F capacitor. Relay-Driver Control Input. Drive RLYON_ high to enable RLYD_, drive RLYON_ low to turn off the MOSFET switch for the channel and disable RLYD_. ______________________________________________________________________________________ +48V Quad Hot-Swap Controllers For Power-Over-LAN The MAX5913A/MAX5914A quadruple hot-swap controllers provide Power-Over-MDI, also known as PowerOver-LAN systems (Figure 5). The MAX5913A/ MAX5914A enable control of four external n-channel MOSFET switches from a single V CC ranging from +35V to +72V, with timing control and current-limiting functions built in. The MAX5913A/MAX5914A features include undervoltage lockout (UVLO), 100mA relay drivers, dual-level current sense, foldback current limit, programmable overcurrent time and auto-retry periods, internal charge pumps to drive external MOSFET and soft-start, port status output indicating power-OK (POK) or open-circuit conditions (Figure 6). Switch and Relay Control Inputs The MAX5913A/MAX5914A ON_ inputs turn on the corresponding MOSFET switch. Driving ON_ high turns on the switch if the corresponding RLYON is driven high, and VCC > VUVLO for more than 25.6ms. Driving RLYON_ high immediately turns on the corresponding relay, and activates the 25.6ms delay after which the corresponding ON_ input is active. Driving RLYON_ low immediately turns off the switch and activates a 3.2ms delay, after which the relay is turned off. These internal delays safely allow driving ON_ and RLYON_ simultaneously. The relay is turned on while the switch is off so that there is no voltage across the relay contacts. The relay is turned off while the switch is off so that there is no current flowing when the relay contacts are opened (see Figure 3). Input Voltage and UVLO The MAX5913A/MAX5914A operate from a +35V to +72V supply voltage. VCC powers the MAX5913A/MAX5914A analog circuitry and is monitored continuously during startup and normal operation. The MAX5913A/MAX5914A keep all MOSFET switches and relay drivers securely off before V CC rises above V UVLO . The MAX5913A/ MAX5914A turn off all MOSFET switches and relay drivers after VCC falls below VUVLO - VUVLO,H. Startup When the turn-on condition is met (see the Input Voltage and UVLO and Switch and Relay Control Inputs sections), the MAX5913A/MAX5914A slowly turn on the external MOSFET switch by charging its gate using a constant current source, IGATE (10A typ). The gate voltage slope is determined by the total gate capacitance CGATE connected to this node. Since the output voltage follows the gate voltage, thus the output rises with a slope determined by: VOUT I = GATE t CGATE If a capacitor load is connected to the output, the total current through the FET is: I = IGATE CL + IL CGATE where CL is the load capacitance and IL is the current required by any load connected to the output during the startup phase. If the current through the FET reaches the programmed current-limit value: IMAX = VSC RSENSE the internal current-limit circuitry activates and regulates this FET current to be a value, ILIM, that depends on VOUT (IFLBK) (Figure 8). See the Current Sensing and Regulation section. In this case, the maximum rate of change of the output is determined by: VOUT ILIM - IL = t CL The formula shows the necessity for ILIM to be larger than IL in order to allow the output voltage to rise. The foldback function is active as long as the circuit is in overcurrent condition. Should the overcurrent condition persist for a period longer than the maximum time tO, the switch is latched off and GATE_ is discharged to ground with a 1mA pulldown current. If auto-retry is enabled, the switch turns on again after a waiting period, tOFF, which is determined by the programmed duty cycle. After the startup, the internal charge pumps provide (VCC + 9V) typical gate overdrive to fully turn on the switch. When the switch is fully on (voltage drop across the switch is 1.5V), and the switch is not in current limit, the POK signal is asserted. Current Sensing and Regulation The MAX5913A/MAX5914A control port current with using two voltage comparators (dual-level detection) that sense the voltage drop across an external currentsense resistor. Connect CSP_ to VCC and connect a current-sense resistor between CSP_ and DRAIN_. Kelvin sensing should be used as shown in Figure 7. ______________________________________________________________________________________ 11 MAX5913A/MAX5914A Detailed Description MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN Test Circuits and Timing Diagrams (VCC - VOUT) 1.5V (POWER-OK IS GOOD) VCC VUVLO VCC OC DETECTOR ENABLED (INTERNAL SIGNAL) tOC VGATE +1V +1V VGATE tD, UVLO tLPFD Figure 2. Open-Circuit Detector Deglitch Delay Figure 1. UVLO Deglitch Delay 0.33 VIH RLYON 200 470F 270F 100 VTEST VIL CSP1 DRAIN1 GATE1 OUT1 ON1 RLYON1 VGATE +42V +1V VCC 270F MAX5913A/MAX5914A 270F ON2 RLYON2 tON_DEL tOFF_DEL CSP2 DRAIN2 GATE2 OUT2 DGND VRLY 3.3V 100 RLYD (MAX5913A) 0.33 VOUT 270F Figure 3. Port Turn-On Delay, Relay Turn-Off Delay Figure 4. Channel-to-Channel Crosstalk Test Circuit The first comparator compares the sensed voltage against the VSC threshold (typically 142.5mV). Choose a sense resistor as follows: RSENSE = VSC / IMAX across the sense resistor is lowered to a minimum value of 48mV (typ). This foldback feature helps reduce the power dissipation in the external power FET during output overload and output short-circuit conditions. If a load with very low activation voltage is permanently connected to the output, make the minimum limit current sufficiently larger than the load current. If the load current indeed exceeds the foldback-limit value, the MAX5913A/ MAX5914A are not able to power up the switch. where IMAX is the maximum current allowed through the switch. When IMAX is reached, foldback current-limit circuitry regulates the current limit as a function of VOUT (Figure 8). As VOUT approaches zero, the maximum voltage drop 12 ______________________________________________________________________________________ +48V Quad Hot-Swap Controllers For Power-Over-LAN MAX5913A/MAX5914A VCC = +35V TO +72V ON1 ON2 ON3 ON4 RLYON1 RLYON2 RLYON3 RLYON4 OCEN RTRYEN STATOUT DC DIGITAL INTERFACE INPUTS +12V +3.3V VCC CSP1 DRAIN1 GATE1 N PORT 1 OUT1 MAX5913A VRLY VRLY VDD VCC CSP4 FAULT STAT1 DIGITAL INTERFACE OUTPUTS STAT2 DRAIN4 STAT3 GATE4 STAT4 N PORT 4 OUT4 RTIM DGND AGND RLYD1 RLYD4 VRLY Figure 5. Typical Application Circuit Open-Circuit Detection a 900ms delay. The open-circuit voltage threshold is set at 3mV across the current-sense resistor. Drive OCEN high to enable open-circuit detectors for all four ports. Drive OCEN low to disable the detectors. Each port has an open-circuit flag that can be read from STAT_ outputs when the STATOUT is low. STAT_ output high indicates that the switch is latched off due to an open-circuit condition on that port. To reset the latch pull ON_ low and then high to restart (Table 1). The MAX5913A/MAX5914A detect when a port has low current or is open circuit, and turn off the switch to that port. After the switch is turned on and the POK conditions are met, the open-circuit detector is enabled after The MAX5913A/MAX5914A sense the output voltage of the port at the source of the external MOSFET switch. A second comparator with a detection threshold of 3VSC activates a fast 15mA pulldown of the gate. The purpose of this comparator is to rapidly discharge the gate when a momentary current peak overstresses the external FET, helping the regulation to act more rapidly. The sense resistor is also used to detect an open-circuit or low-current condition with a typical threshold of 3mV. Output Voltage Sense and Power-OK ______________________________________________________________________________________ 13 MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN RTRYEN DC RTIM CSP VCC 420mV 142.5mV 3mV MAX5913A MAX5914A FOLDBACK NL CONTROL DC COUNTER RESET LOGIC RSENSE DUAL LEVEL DETECTION FROM LOGIC CONTROLLER UVLO TIMING OSCILLATOR CHARGE PUMP DRAIN 10A 1.236V CSP -1.5V POK COMPARATOR LOGIC CONTROLLER GATE VDD OUT VDD TO LOGIC OPEN-CIRCUIT CONTROLLER DETECTOR 1mA 8A VRLY RELAY CONTROL 1mA DGND DELAY OCEN ON AGND RLYON RLYD DGND Figure 6. Functional Diagram Internally the circuit compares the output voltage with VCC to determine when the FET is completely on. A POK condition is met when: (VCC - VOUT) 1.5V The internal circuit monitors V OUT to determine the value of the foldback current when the circuit goes into current-limit conditions. The value of the current limit decreases as the output voltage decreases in order to limit the power dissipation of the FET. The nonlinear relationship between V OUT and I LIM is depicted in Figure 8. The foldback circuit is active whenever the MAX5913A/ MAX5914A are in current-limit mode after an overcurrent condition has been detected. 14 Connect a catch diode to analog ground and a 100 resistor in series with OUT_ to limit the current during negative inductive kicks that can bring OUT_ below the ground potential (Figure 5). Relay Drivers The MAX5913A/MAX5914A include on-chip relay drivers, RYLD_, capable of sinking 100mA. When RLYON_ goes high, the MAX5913A/MAX5914A immediately enable the relay driver, and the corresponding ON_ switch control input is delayed 25.6ms to allow the relay to close under a zero-voltage condition. When RLYON_ goes low, the MAX5913A/MAX5914A immediately turn off the corresponding switch, and then turn off the relay driver after a 3.2ms delay, ensuring the relay contacts open under a zero-current condition. The polarity of the MAX5913A ______________________________________________________________________________________ +48V Quad Hot-Swap Controllers For Power-Over-LAN tO = (RRTIM / 2k) (6.4ms) If RTIM is unconnected, an internal resistor sets tO to a nominal 6.4ms. The MAX5913A/MAX5914A logic interface controls the device functionality. All the basic control functions for the four switches are separated. ON_ enables individual on/off control of each MOSFET (the corresponding relay must be on to turn on the switch). RLYON_ enables individual on/off control of each relay. STAT_ indicates POK or Port-OC (open circuit) status of each switch. The other logic pins are common to all four switches. A single FAULT output goes low when any of the four channels is latched off. Driving OCEN high enables the open-circuit detectors. Driving RTRYEN high enables the auto-retry function, RTRYEN low enables the switch latch-off function. DC, a three-level logic input, programs the duty cycle. The STATOUT input selects the signal multiplexed at STAT_ outputs (Table 1.). Driving STATOUT high routes POK status to the STAT_ outputs. Driving STATOUT low routes Port-OC status to the STAT_ outputs. Auto-Retry and Programmable Duty Cycle Fault Management Programmable Timing, RTIM An external resistor from RTIM to DGND sets the frequency of the internal oscillator upon which tO and the auto-retry times are based. Use 2k to 40k resistors for RRTIM. The MAX5913A/MAX5914A feature auto-retry with adjustable duty cycle. Driving RTRYEN high enables the auto-retry function. When the switch encounters an overcurrent for a period greater than tO, the switch is turned off, and remains off for a tOFF programmed by DC, a three-level input. After the tOFF period, the switch is automatically turned on again. When the port encounters a continuous overload or short-circuit condition, the switch turns on and off repeatedly with the on duty cycle of 1%, 2%, or 4% depending on the DC input state (Table 2). When RTRYEN is low, the auto-retry is disabled, and a fault condition at the switch turns the switch off and the switch remains latched off. Driving the corresponding ON control input low resets the latch. Pulling ON high to turn on the switch. However, the MAX5913A/MAX5914A always wait a minimum time, tOFF, before restarting the switch. UVLO and Power-OK The MAX5913A/MAX5914A monitor the VCC input voltage and each switch's current and voltage to determine POK, overcurrent, or Port-OC status. When VCC falls below the UVLO threshold, FAULT goes low and all four switches and relays are turned off. When the volage across the switch is less than 1.5V, the switch is fully on, and if the switch is not in current limit or open circuit, POK status is good (high). Open-Circuit Faults With the open-circuit detector enabled, when any switch current falls below the open-circuit detector threshold current, the open-circuit detector turns off the switch after a 25.6ms delay, FAULT goes low, and the Port-OC flag is set for that switch. To clear the switch latched-off condition, FAULT and Port-OC flags drive the corresponding ON input low. Table 1. Status Output PORT_ CONDITION OCEN STATOUT STAT_ Enabled. Switch fully on and not in current limit. x H H (Power-OK_ is good) Enabled. Switch in current limit, or VDS > 1.5V. x H L (Power-OK_ is not good) Enabled. Switch current is less than OC threshold, port is latched off. H L H (Port-OC_ , Port current is low or zero) Enabled. Switch fully on and output current is greater than OC threshold. H L L (Port-OC_ , Port current is good) Disabled. L L L ______________________________________________________________________________________ 15 MAX5913A/MAX5914A Logic Interface and Status Outputs RLYD_ is opposite to that of the MAX5914A. For the MAX5913A, upon the assertion of the RLYON_ input, RLYD_ sinks 100mA to DGND. For the MAX5914A, when RLYON_ is high, an internal 1mA current source pulls up RLYD_ to VDD. A 100mA catch diode is internally connected between RYLD_ and V RLY to protect the MAX5913A/MAX5914A from inductive kicks from the relay coil. VRLY must be connected to the high-side relay supply voltage. MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN Overcurrent Faults When an on-switch current exceeds the current-limit threshold, foldback circuitry activates and regulates the switch current. When the current limit lasts for longer than tO, the switch latches off. The POK status flag is set low, and the FAULT flag is set. If auto-retry is enabled, the switch remains off for a period tOFF. If auto-retry is disabled, the switch remains latched off, and FAULT is low. Reset the latch and FAULT by driving corresponding ON_ low. Applications Information value, but large enough to allow the switch to remain on during large output load-current transients. The smaller the tO, the faster the MAX5913A/MAX5914A turn off the external FET in case of output overload or short-circuit condition. 2) For startup with current limit, when: CL VSC I = IGATE + IL C R GATE SENSE which is expected when: Considerations for circuit design include output capacitor requirements, current-limit requirements, setting the maximum on-time in current limit, and choosing a suitable MOSFET and on-time duty cycle in auto-retry. Output Capacitor Requirements The load capacitor requirements should be determined first, as this affects the required startup. Current-Limit Requirements (Choosing RSENSE) The current limit should be set to at least 20% higher than the expected full load current. If current limit is also used to control startup current, then set this limit high enough so that the output voltage can rise and settle before tO elapses (see the Setting tO (Choosing RRTIM) section). Setting tO (Choosing RRTIM) Choose the tO time by connecting a 2k to 40k resistor from RTIM to DGND. The minimum 6.4ms tO is set with RRTIM = 2k. The maximum 128ms tO is set with RRTIM = 40k set according to the following equation: tO = (RRTIM / 2k) (6.4ms) tO should be chosen appropriately, depending on the startup condition. There are two cases: 1) For startup without current limit, when: I = IGATE CL CGATE + IL < VSC RSENSE The startup current does not reach the maximum current-limit threshold and tO will not activate during startup condition. In this case, set t O to a small 16 CL CGATE is large, tO must be set to be long enough to allow the output voltage to rise and settle before tO elapses. In this case, tO must satisfy the following equation: t O = CL 18 V - 18V + CL CC 2 IMAX - IL IMAX - IL 3 where VCC is the input voltage and given that IL < ILIM. Choosing Power MOSFET The FET must withstand a short-circuit condition where its power dissipation is PDISS = VCC ILIM. The FET must have sufficient thermal capacitance to prevent thermal heating damage during the tO time. Choose Duty Cycle (Setting DC) The duty cycle can be adjusted to allow time for heat to dissipate between tO cycles, allowing use of smaller MOSFETs with lower thermal capacitance. For smaller duty cycle, a smaller FET is sufficient. See Table 2 for setting the duty cycle. The auto-retry off-time should not be too long to keep the system wait time during retry period to a reasonable value. For example, when tO is set to 128ms and duty cycle is set to 1%, the retry time is 99 128ms = 12.7s. Application Circuits In a typical LAN system there are two ways to deliver power over the LAN cable. Power can be supplied to the unused cable pairs, or power can be supplied over the signal pairs (Figures 9 and 10). ______________________________________________________________________________________ +48V Quad Hot-Swap Controllers For Power-Over-LAN ILIM CSP_ DRAIN_ SENSE RESISTOR IMAX = VSC RSENSE IMAX /3 MAX5913A MAX5914A Figure 7. Recommended Layout for Kelvin-Sensing Current Through Sense Resistor 0V VOUT 18V Figure 8. Foldback Current-Limit Response Table 2. Duty Programming Cycle DC tOFF DUTY CYCLE 0 99 tO 1% 1 49 tO 2% Open 24 tO 4% ______________________________________________________________________________________ 17 MAX5913A/MAX5914A HIGH-CURRENT PATH MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN LAN SWITCH N +48V POWER OVER SIGNAL PAIRS RJ45 RJ45 +48V PD MAX5913A MAX5914A +48V OUT CAT 5 DATA POWERED DEVICE (IP PHONE, ETC.) Figure 9. Power Sent Over Signal Pairs +48V POWER OVER SPARE PAIRS MIDSPAN HUB RJ45 RJ45 RJ45 RJ45 CAT 5 PD N +48V OUT CAT 5 POWERED DEVICE (IP PHONE, ETC.) +48V MAX5913A MAX5914A Figure 10. Power Sent Over Spare Pairs 18 ______________________________________________________________________________________ +48V Quad Hot-Swap Controllers For Power-Over-LAN VCC = +35V TO +72V ON1 ON2 ON3 ON4 RLYON1 RLYON2 RLYON3 RLYON4 OCEN RTRYEN STATOUT DC DIGITAL INTERFACE INPUTS +12V +3.3V VCC CSP1 DRAIN1 N GATE1 PORT 1 OUT1 MAX5913A VRLY VRLY VDD VCC CSP4 FAULT DIGITAL INTERFACE OUTPUTS STAT1 STAT2 DRAIN4 STAT3 N GATE4 STAT4 PORT 4 OUT4 RTIM DGND AGND RLYD1 VRLY RLYD4 Chip Information PROCESS: BiCMOS Package Information For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 44 MQFP M44+3 21-0826 90-0169 ______________________________________________________________________________________ 19 MAX5913A/MAX5914A Typical Operating Circuit MAX5913A/MAX5914A +48V Quad Hot-Swap Controllers For Power-Over-LAN Revision History REVISION NUMBER REVISION DATE 0 5/04 Initial release 1 1/11 Released the MAX5914A. Updated the Ordering Information, Electrical Characteristics, Typical Operating Characteristics, Pin Description, and the Programming Timing, RTIM section DESCRIPTION PAGES CHANGED -- 1-9, 15 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 20 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2011 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.