INTEGRATED CIRCUITS DATA SHEET UDA1334TS Low power audio DAC Product specification Supersedes data of 1999 Nov 11 File under Integrated Circuits, IC01 2000 Oct 25 Philips Semiconductors Product specification Low power audio DAC UDA1334TS CONTENTS 9 LIMITING VALUES 10 HANDLING 11 THERMAL CHARACTERISTICS 12 QUALITY SPECIFICATION 13 DC CHARACTERISTICS 14 AC CHARACTERISTICS 2.0 V supply voltage 3.0 V supply voltage Timing 1 FEATURES 1.1 1.2 1.3 1.4 General Multiple format data interface DAC digital sound processing Advanced audio configuration 2 APPLICATIONS 3 GENERAL DESCRIPTION 4 ORDERING INFORMATION 14.1 14.2 14.3 5 QUICK REFERENCE DATA 15 APPLICATION INFORMATION 6 BLOCK DIAGRAM 16 PACKAGE OUTLINE 7 PINNING 17 SOLDERING 8 FUNCTIONAL DESCRIPTION 17.1 8.1 8.2 8.3 8.4 8.5 8.6 8.6.1 8.6.2 8.6.3 8.6.4 System clock Interpolation filter Noise shaper Filter stream DAC Power-on reset Feature settings Digital interface format select Mute control De-emphasis control Power control and sampling frequency select Introduction to soldering surface mount packages Reflow soldering Wave soldering Manual soldering Suitability of surface mount IC packages for wave and reflow soldering methods 2000 Oct 25 17.2 17.3 17.4 17.5 2 18 DEFINITIONS 19 LIFE SUPPORT APPLICATIONS Philips Semiconductors Product specification Low power audio DAC 1 1.1 UDA1334TS FEATURES General * 1.8 to 3.6 V power supply voltage * Integrated digital filter plus DAC * Supports sample frequencies from 8 to 100 kHz * Automatic system clock versus sample rate detection * Low power consumption * No analog post filtering required for DAC 2 * Slave mode only applications This audio DAC is excellently suitable for digital audio portable application, such as portable MD, MP3 and DVD players. * Easy application * SSOP16 package. 1.2 Multiple format data interface 3 * I2S-bus and LSB-justified format compatible DAC digital sound processing The UDA1334TS has basic features such as de-emphasis (at 44.1 kHz sampling rate) and mute. * Digital de-emphasis for 44.1 kHz sampling rate * Mute function. 1.4 GENERAL DESCRIPTION The UDA1334TS supports the I2S-bus data format with word lengths of up to 24 bits and the LSB-justified serial data format with word lengths of 16, 20 and 24 bits. * 1fs input data rate. 1.3 APPLICATIONS Advanced audio configuration * High linearity, wide dynamic range and low distortion * Standby or Sleep mode in which the DAC is powered down. 4 ORDERING INFORMATION TYPE NUMBER UDA1334TS 2000 Oct 25 PACKAGE NAME DESCRIPTION VERSION SSOP16 plastic shrink small outline package; 16 leads; body width 4.4 mm SOT369-1 3 Philips Semiconductors Product specification Low power audio DAC 5 UDA1334TS QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supplies VDDA DAC analog supply voltage VDDD digital supply voltage IDDA DAC analog supply current IDDD digital supply current Tamb ambient temperature 1.8 2.0 3.6 V 1.8 2.0 3.6 V normal operation - 2.1 - mA Sleep mode - 150 - A normal operation - 1.2 - mA Sleep mode - 50 - A -40 - +85 C Digital-to-analog convertor (VDDA = VDDD = 2.0 V) Vo(rms) output voltage (RMS value) at 0 dB (FS) digital input; note 1 - 500 - mV (THD + N)/S total harmonic distortion-plus-noise to signal ratio fs = 44.1 kHz; at 0 dB - -80 - dB fs = 44.1 kHz; at -60 dB; A-weighted - -37 - dB fs = 96 kHz; at 0 dB - -75 - dB fs = 96 kHz; at -60 dB; A-weighted - -35 - dB fs = 44.1 kHz; code = 0; A-weighted - 97 - dB fs = 96 kHz; code = 0; A-weighted - 95 - dB MUTE = HIGH; A-weighted - 110 - dB - 100 - dB S/N cs signal-to-noise ratio channel separation Digital-to-analog convertor (VDDA = VDDD = 3.0 V) Vo(rms) output voltage (RMS value) at 0 dB (FS) digital input; note 1 - 750 - mV (THD + N)/S total harmonic distortion-plus-noise to signal ratio fs = 44.1 kHz; at 0 dB - -90 - dB fs = 44.1 kHz; at -60 dB; A-weighted - -40 - dB fs = 96 kHz; at 0 dB - -85 - dB fs = 96 kHz; at -60 dB; A-weighted - -37 - dB fs = 44.1 kHz; code = 0; A-weighted - 100 - dB fs = 96 kHz; code = 0; A-weighted - 98 - dB MUTE = HIGH; A-weighted - 110 - dB - 100 - dB at 2.0 V supply voltage - 7.0 - mW at 3.0 V supply voltage - 17 - mW clock running - 0.75 - mW no clock running - 0.3 - mW S/N cs signal-to-noise ratio channel separation Power dissipation (at fs = 44.1 kHz) P power dissipation Sleep mode; at 2.0V supply voltage Note 1. The DAC output voltage scales proportional to the power supply voltage. 2000 Oct 25 4 Philips Semiconductors Product specification Low power audio DAC 6 UDA1334TS BLOCK DIAGRAM VSSD VDDD handbook, full pagewidth 4 BCK WS DATAI 1 2 3 5 DIGITAL INTERFACE DE-EMPHASIS UDA1334TS SYSCLK MUTE DEEM PCS 6 7 8 11 INTERPOLATION FILTER 9 SFOR1 SFOR0 10 NOISE SHAPER VOUTL DAC 14 13 15 VDDA VSSA Fig.1 Block diagram. 2000 Oct 25 16 DAC 5 12 Vref(DAC) VOUTR MGL877 Philips Semiconductors Product specification Low power audio DAC 7 UDA1334TS PINNING SYMBOL PIN PAD TYPE DESCRIPTION BCK 1 5 V tolerant digital input pad; note 1 bit clock input WS 2 5 V tolerant digital input pad; note 1 word select input DATAI 3 5 V tolerant digital input pad; note 1 serial data input VDDD 4 digital supply pad digital supply voltage VSSD 5 digital ground pad digital ground SYSCLK 6 5 V tolerant digital input pad; note 1 system clock input SFOR1 7 5 V tolerant digital input pad; note 1 serial format select 1 MUTE 8 5 V tolerant digital input pad; note 1 mute control DEEM 9 5 V tolerant digital input pad; note 1 de-emphasis control PCS 10 3-level input pad; note 2 power control and sampling frequency select SFOR0 11 digital input pad; note 2 serial format select 0 Vref(DAC) 12 analog pad DAC reference voltage VDDA 13 analog supply pad DAC analog supply voltage VOUTL 14 analog output pad DAC output left VSSA 15 analog ground pad DAC analog ground VOUTR 16 analog output pad DAC output right Notes 1. 5 V tolerant is only supported if the power supply voltage is between 2.7 and 3.6 V. For lower power supply voltages this is maximum 3.3 V tolerant. 2. Because of test issues these pads are not 5 V tolerant and they should be at power supply voltage level or at a maximum of 0.5 V above that level. handbook, halfpage BCK 1 16 VOUTR WS 2 15 VSSA DATAI 3 VDDD 4 14 VOUTL UDA1334TS VSSD 5 13 VDDA 12 Vref(DAC) SYSCLK 6 11 SFOR0 SFOR1 7 10 PCS MUTE 8 9 DEEM MGL878 Fig.2 Pin configuration. 2000 Oct 25 6 Philips Semiconductors Product specification Low power audio DAC 8 UDA1334TS Table 2 FUNCTIONAL DESCRIPTION 8.1 System clock Example using a 12.228 MHz system clock SAMPLING FREQUENCY CLOCK MODE 96 kHz 128fs The UDA1334TS operates in slave mode only; this means that in all applications the system must provide the system clock and the digital audio interface signals (BCK and WS). 64 The system clock must be locked in frequency to the digital interface signals. The UDA1334TS automatically detects the ratio between the SYSCLK and WS frequencies. kHz(1) 192fs 48 kHz 256fs 32 kHz 384fs 24 kHz 512fs 16 kHz 768fs Note 1. This mode can only be supported for power supply voltages down to 2.4 V. For lower voltages, in 192fs mode the sampling frequency should be limited to 55 kHz. The BCK clock can be up to 64fs, or in other words the BCK frequency is 64 times the Word Select (WS) frequency or less: fBCK 64 x fWS. Remarks 8.2 1. The WS edge MUST fall on the negative edge of the BCK at all times for proper operation of the digital I/O data interface. The interpolation digital filter interpolates from 1fs to 64fs by cascading FIR filters (see Table 3). 2. For LSB-justified formats it is important to have a WS signal with a duty factor of 50%. Table 3 The modes which are supported are given in Table 1. Table 1 Interpolation filter Supported sampling ranges Interpolation filter characteristics ITEM CONDITION VALUE (dB) Pass-band ripple 0 to 0.45fs 0.02 >0.55fs -50 0 to 0.45fs >114 Stop band CLOCK MODE SAMPLING RANGE 768fs 8 to 55 kHz 512fs 8 to 100 kHz 8.3 384fs 8 to 100 kHz 256fs 8 to 100 kHz 192fs 8 to 100 kHz(1)(2) 128fs 8 to 100 kHz(2) The 5th-order noise shaper operates at 64fs. It shifts in-band quantization noise to frequencies well above the audio band. This noise shaping technique enables high signal-to-noise ratios to be achieved. The noise shaper output is converted into an analog signal using an Filter Stream DAC (FSDAC). Dynamic range Notes 1. This mode can only be supported for power supply voltages down to 2.4 V. For lower voltages, in 192fs mode the sampling frequency should be limited to 55 kHz. 2. Not supported in low-sampling frequency mode. An example is given in Table 2 for a 12.228 MHz system clock input. 2000 Oct 25 7 Noise shaper Philips Semiconductors Product specification Low power audio DAC 8.4 UDA1334TS Filter stream DAC The FSDAC is a semi-digital reconstruction filter that converts the 1-bit data stream of the noise shaper to an analog output voltage. The filter coefficients are implemented as current sources and are summed at virtual ground of the output operational amplifier. In this way very high signal-to-noise performance and low clock jitter sensitivity is achieved. No post-filter is needed due to the inherent filter function of the DAC. On-board amplifiers convert the FSDAC output current to an output voltage signal capable of driving a line output. 3.0 VDDD handbook, halfpage (V) 1.5 0 t The output voltage of the FSDAC scales proportional with the power supply voltage. 8.5 3.0 VDDA (V) Power-on reset 1.5 The UDA1334TS has an internal Power-on reset circuit (see Fig.3) which resets the test control block. 0 The reset time (see Fig.4) is determined by an external capacitor which is connected between pin Vref(DAC) and ground. The reset time should be at least 1 s for Vref(DAC) < 1.25 V. When VDDA is switched off, the device will be reset again for Vref(DAC) < 0.75 V. t 3.0 Vref(DAC) (V) 1.5 1.25 During the reset time the system clock should be running. 0.75 0 >1 s t MGL984 handbook, halfpage 3.0 V VDDA 13 Fig.4 Power-on reset timing. 50 k Vref(DAC) C1 > 10 F RESET CIRCUIT 12 50 k UDA1334TS MGU248 Fig.3 Power-on reset circuit. 2000 Oct 25 8 Philips Semiconductors Product specification Low power audio DAC 8.6 UDA1334TS 8.6.3 Feature settings De-emphasis can be switched on for fs = 44.1 kHz by setting pin DEEM at HIGH level. The function description of pin DEEM is given in Table 6. The features of the UDA1334TS can be set by control pins SFOR1, SFOR0, MUTE, DEEM and PCS. 8.6.1 DIGITAL INTERFACE FORMAT SELECT Table 6 The digital audio interface formats (see Fig.5) can be selected via the pins SFOR1 and SFOR0 as shown in Table 4. Table 4 SFOR0 INPUT FORMAT LOW LOW LOW HIGH LSB-justified 16 bits input HIGH LOW LSB-justified 20 bits input HIGH HIGH LSB-justified 24 bits input mute on FUNCTION LOW normal operating mode MID low sampling frequency mode Power-down or Sleep mode The low sampling frequency mode is required to have a higher oversampling rate in the noise shaper in order to improve the signal-to-noise ratio. In this mode the oversampling ratio of the noise shaper will be 128fs instead of 64fs. When the output signal is fully muted (pin MUTE at HIGH level), a silence switch inside the FSDAC is activated. In this way a very high signal-to-noise ratio can be achieved in case the output is muted. 2000 Oct 25 PCS function definition HIGH FUNCTION HIGH POWER CONTROL AND SAMPLING FREQUENCY PCS Mute control mute off de-emphasis on Table 7 The output signal can be soft muted by setting pin MUTE to HIGH level as shown in Table 5. LOW de-emphasis off Pin PCS is a 3-level pin and is used to set the mode of the UDA1334TS. The definition is given in Table 7. input MUTE CONTROL MUTE LOW SELECT I2S-bus Table 5 FUNCTION HIGH 8.6.4 Data format selection SFOR1 De-emphasis control DEEM The BCK frequency for the digital audio interface can be maximum 64 times the WS frequency: fBCK 64fWS. 8.6.2 DE-EMPHASIS CONTROL 9 This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... 2 >=8 3 2 3 MSB B2 1 >=8 BCK DATA MSB B2 MSB I2S-BUS FORMAT WS LEFT Philips Semiconductors 1 Low power audio DAC handbook, full pagewidth 2000 Oct 25 RIGHT LEFT WS RIGHT 16 15 1 16 B15 LSB MSB 2 15 2 1 BCK DATA MSB B2 B2 B15 LSB LSB-JUSTIFIED FORMAT 16 BITS 10 WS LEFT 20 RIGHT 19 18 17 16 15 1 20 B19 LSB MSB 2 19 18 17 16 15 2 1 BCK DATA MSB B2 B3 B4 B5 B6 B2 B3 B4 B5 B6 B19 LSB LSB-JUSTIFIED FORMAT 20 BITS WS LEFT 24 23 22 21 20 RIGHT 19 18 17 16 15 2 1 24 B23 LSB MSB 23 22 21 20 19 18 17 16 15 2 1 BCK DATA MSB B2 B3 B4 B5 B6 B7 B8 B9 B10 B2 B3 B4 B5 B6 B7 B8 B9 B10 B23 LSB MGS752 Product specification Fig.5 Digital audio formats. UDA1334TS LSB-JUSTIFIED FORMAT 24 BITS Philips Semiconductors Product specification Low power audio DAC UDA1334TS 9 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT - 4.0 V maximum crystal temperature - 150 C Tstg storage temperature -65 +125 C Tamb ambient temperature -40 +85 C Ves electrostatic handling voltage human body model -2000 +2000 V machine model -200 +200 V VDD supply voltage Txtal(max) note 1 Note 1. All supply connections must be made to the same power supply. 10 HANDLING Inputs and outputs are protected against electrostatic discharge in normal handling. However, it is good practice to take normal precautions appropriate to handling MOS devices. 11 THERMAL CHARACTERISTICS SYMBOL Rth(j-a) PARAMETER CONDITIONS thermal resistance from junction to ambient in free air VALUE UNIT 145 K/W 12 QUALITY SPECIFICATION In accordance with "SNW-FQ-611-E". 13 DC CHARACTERISTICS VDDD = VDDA = 2.0 V; Tamb = 25 C; RL = 5 k. All voltages with respect to ground (pins VSSA and VSSD); unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supplies VDDA DAC analog supply voltage note 1 1.8 2.0 3.6 V VDDD digital supply voltage note 1 1.8 2.0 3.6 V IDDA DAC analog supply current normal operating mode; at 2.0 V supply voltage - 2.1 - mA normal operating mode; at 3.0 V supply voltage - 3.3 - mA Sleep mode - 150 - A normal operating mode; at 2.0 V supply voltage - 1.2 - mA normal operating mode; at 3.0 V supply voltage - 2.1 - mA Sleep mode - 50 - A IDDD 2000 Oct 25 digital supply current 11 Philips Semiconductors Product specification Low power audio DAC SYMBOL UDA1334TS PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Digital input pins; note 2 VIH HIGH-level input voltage at 2.0 V supply voltage 1.3 - 3.3 V at 3.0 V supply voltage 2.0 - 5.0 V at 2.0 V supply voltage -0.5 - +0.5 V at 3.0 V supply voltage VIL LOW-level input voltage -0.5 - +0.8 V ILI input leakage current - - 1 A Ci input capacitance - - 10 pF 3-level input: pin PCS VIH HIGH-level input voltage 0.9VDDD - VDDD V VIM MID-level input voltage 0.4VDDD - 0.6VDDD V VIL LOW-level input voltage 0 - 0.5 V DAC Vref(DAC) reference voltage RO(ref) Vref(DAC) reference output resistance Io(max) maximum output current RL load resistance CL load capacitance with respect to VSSA 0.45VDD 0.5VDD 0.55VDD V - 12.5 - k (THD + N)/S < 0.1%; RL = 800 - 0.88 - mA 3 - - k note 3 - - 50 pF Notes 1. All supply connections must be made to the same external power supply unit. 2. At 3 V supply voltage, the input pads are TTL compatible. However, at 2.0 V supply voltage no TTL levels can be accepted, but levels from 3.3 V domain can be applied to the pins. 3. When the DAC drives a capacitive load above 50 pF, a series resistance of 100 must be used to prevent oscillations in the output operational amplifier. 14 AC CHARACTERISTICS 14.1 2.0 V supply voltage VDDD = VDDA = 2.0 V; fi = 1 kHz; Tamb = 25 C; RL = 5 k. All voltages with respect to ground (pins VSSA and VSSD); unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT DAC Vo(rms) output voltage (RMS value) Vo unbalance between channels (THD + N)/S total harmonic distortion-plus-noise to signal ratio 2000 Oct 25 - 0.5 - V - 0.1 - dB fs = 44.1 kHz; at 0 dB - -80 - dB fs = 44.1 kHz; at -60 dB; A-weighted - -37 - dB fs = 96 kHz; at 0 dB - -75 - dB fs = 96 kHz; at -60 dB; A-weighted - -35 - dB at 0 dB (FS) digital input 12 Philips Semiconductors Product specification Low power audio DAC SYMBOL S/N PARAMETER signal-to-noise ratio cs channel separation PSRR power supply rejection ratio UDA1334TS CONDITIONS MIN. TYP. MAX. UNIT fs = 44.1 kHz; code = 0; A-weighted - 97 - dB fs = 96 kHz; code = 0; A-weighted - 95 - dB MUTE = HIGH; A-weighted - 110 - dB - 100 - dB 60 - dB fripple = 1 kHz; Vripple = 30 mV (p-p) - 14.2 3.0 V supply voltage VDDD = VDDA = 3.0 V; fi = 1 kHz; Tamb = 25 C; RL = 5 k. All voltages with respect to ground (pins VSSA and VSSD); unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT DAC Vo(rms) output voltage (RMS value) Vo unbalance between channels (THD + N)/S total harmonic distortion-plus-noise to signal ratio S/N signal-to-noise ratio cs channel separation PSRR power supply rejection ratio at 0 dB (FS) digital input - 0.75 - V fs = 44.1 kHz; at 0 dB - 0.1 - dB - -90 - dB fs = 44.1 kHz; at -60 dB; A-weighted - -40 - dB fs = 96 kHz; at 0 dB - -85 - dB fs = 96 kHz; at -60 dB; A-weighted - -37 - dB - 100 - dB fs = 44.1 kHz; code = 0; A-weighted fs = 96 kHz; code = 0; A-weighted - 98 - dB MUTE = HIGH; A-weighted - 110 - dB - 100 - dB 60 - dB fripple = 1 kHz; Vripple = 30 mV (p-p) - 14.3 Timing VDDD = VDDA = 1.8 to 3.6 V; Tamb = -20 to +85 C; RL = 5 k. The typical timing is specified at fs = 44.1 kHz (sampling frequency). All voltages with respect to ground (pins VSSA and VSSD); unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT System clock timing (see Fig.6) Tsys tCWH tCWL system clock cycle time system clock HIGH time system clock LOW time fsys = 256fs 35 88 780 ns fsys = 384fs 23 59 520 ns fsys = 512fs 17 44 390 ns fsys < 19.2 MHz 0.3Tsys - 0.7Tsys ns fsys 19.2 MHz 0.4Tsys - 0.6Tsys ns fsys < 19.2 MHz 0.3Tsys - 0.7Tsys ns fsys 19.2 MHz 0.4Tsys - 0.6Tsys ns Serial interface timing (see Fig.7) fBCK bit clock frequency - - 64fs Hz tBCKH bit clock HIGH time 50 - - ns 2000 Oct 25 13 Philips Semiconductors Product specification Low power audio DAC SYMBOL UDA1334TS PARAMETER CONDITIONS MIN. TYP. MAX. UNIT tBCKL bit clock LOW time 50 - - ns tr rise time - - 20 ns tf fall time - - 20 ns tsu(DATAI) set-up time data input 20 - - ns th(DATAI) hold time data input 0 - - ns tsu(WS) set-up time word select 20 - - ns th(WS) hold time word select 10 - - ns t CWH handbook, full pagewidth MGR984 t CWL Tsys Fig.6 System clock timing. handbook, full pagewidth WS th(WS) tBCKH tr tsu(WS) tf BCK tsu(DATAI) tBCKL Tcy(BCK) th(DATAI) DATAI MGL880 Fig.7 Serial interface timing. 2000 Oct 25 14 Philips Semiconductors Product specification Low power audio DAC UDA1334TS 15 APPLICATION INFORMATION analog supply voltage handbook, full pagewidth R7 1 C9 system clock R5 SYSCLK 47 digital supply voltage 47 F (16 V) 47 F (16 V) C10 C6 100 nF (63 V) VSSA 100 nF (63 V) 15 VDDA 13 R6 1 C5 VSSD 5 VDDD 4 6 14 BCK WS DATAI SFOR1 SFOR0 MUTE DEEM PCS VOUTL C3 47 F (16 V) 1 2 R3 R1 220 k C1 3 7 11 UDA1334TS 16 8 9 VOUTR C4 47 F (16 V) 12 left output 100 10 nF (63 V) R4 right output 100 R2 220 k C2 10 nF (63 V) Vref(DAC) C8 100 nF (63 V) 10 C7 47 F (16 V) MGL879 Fig.8 Typical application diagram. 2000 Oct 25 15 Philips Semiconductors Product specification Low power audio DAC UDA1334TS 16 PACKAGE OUTLINE SSOP16: plastic shrink small outline package; 16 leads; body width 4.4 mm D SOT369-1 E A X c y HE v M A Z 9 16 Q A2 A (A 3) A1 pin 1 index Lp L 1 8 detail X w M bp e 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) mm 1.5 0.15 0.00 1.4 1.2 0.25 0.32 0.20 0.25 0.13 5.30 5.10 4.5 4.3 0.65 6.6 6.2 1.0 0.75 0.45 0.65 0.45 0.2 0.13 0.1 0.48 0.18 10 0o Note 1. Plastic or metal protrusions of 0.20 mm maximum per side are not included. OUTLINE VERSION SOT369-1 2000 Oct 25 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION ISSUE DATE 95-02-04 99-12-27 MO-152 16 o Philips Semiconductors Product specification Low power audio DAC UDA1334TS If wave soldering is used the following conditions must be observed for optimal results: 17 SOLDERING 17.1 Introduction to soldering surface mount packages * Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). * For packages with leads on two sides and a pitch (e): - larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended. 17.2 - smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. * For packages with leads on four sides, the footprint must be placed at a 45 angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Typical reflow peak temperatures range from 215 to 250 C. The top-surface temperature of the packages should preferable be kept below 220 C for thick/large packages, and below 235 C for small/thin packages. 17.3 17.4 Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C. To overcome these problems the double-wave soldering method was specifically developed. 2000 Oct 25 Manual soldering 17 Philips Semiconductors Product specification Low power audio DAC 17.5 UDA1334TS Suitability of surface mount IC packages for wave and reflow soldering methods SOLDERING METHOD PACKAGE WAVE BGA, LFBGA, SQFP, TFBGA not suitable suitable(2) HBCC, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, SMS not PLCC(3), SO, SOJ suitable LQFP, QFP, TQFP SSOP, TSSOP, VSO REFLOW(1) suitable suitable suitable not recommended(3)(4) suitable not recommended(5) suitable Notes 1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the "Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods". 2. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 4. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2000 Oct 25 18 Philips Semiconductors Product specification Low power audio DAC UDA1334TS 18 DATA SHEET STATUS DATA SHEET STATUS PRODUCT STATUS DEFINITIONS (1) Objective specification Development This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. Preliminary specification Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Note 1. Please consult the most recently issued data sheet before initiating or completing a design. 19 DEFINITIONS 20 DISCLAIMERS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Right to make changes Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 2000 Oct 25 19 Philips Semiconductors - a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW, Tel. +48 22 5710 000, Fax. +48 22 5710 001 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SAO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 5F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2451, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 60/14 MOO 11, Bangna Trad Road KM. 3, Bagna, BANGKOK 10260, Tel. +66 2 361 7910, Fax. +66 2 398 3447 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 3341 299, Fax.+381 11 3342 553 For all other countries apply to: Philips Semiconductors, Marketing Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 Internet: http://www.semiconductors.philips.com SCA 70 (c) Philips Electronics N.V. 2000 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 753503/25/02/pp20 Date of release: 2000 Oct 25 Document order number: 9397 750 07497