MAIN FEATURES * High sensitivity and high SNR performance linear CCD * 1024, 2048 or 4096 resolution with 10m square pixels * 512, 1024 or 2048 resolution with 14m square pixels * 100 % aperture, Built-in anti blooming, No lag * Camera LinkTM data format (base configuration) * High data rate up to 60 Mpixels/s * * Flexible and easy to operate via RS232 control - gain : 0dB to 40dB by step of 0.05dB - dynamic range : 8, 10 or 12bits data - offset (for contrast expansion) - trigger mode : free run or external trigger modes - data output mode (dual, single) Multi camera synchronization * Single power supply : DC 12 V to 24 V * Very Compact design : 56 x 60 x 38.6 mm (w,h,l) * High reliability - CE & FCC compliant * C, F (Nikon) or K (Pentax) mount adapter (lens not supplied) AVIIVA TM CameraLink linescan camera TM PRODUCT DESCRIPTION This camera is designed with three concepts in mind : Compactness, accuracy and versatility. * A very compact mechanical design incorporates a 0.5K to 4K sensors * ATMEL manages the whole chain, from the sensor to the camera. The result is a camera able to work in 12 bits, with a dedicated electronics offering an excellent signal to noise ratio. * The programmable settings let you work at different integration time, gain and offset. External clock and trigger allow to synchronise several cameras. APPLICATIONS Performance and reliability of this camera make it well suited for the most demanding industrial applications, from web inspection to document scanning, from surface inspection to metrology. Issue 2.4 - 07 FEB 2002 AVIIVA CameraLinkTM 2/15 1. TYPICAL PERFORMANCES Sensor characteristics at maximum pixel rate Resolution Pixel size (square) pixels m m kHz Max Line rate Anti blooming 512 14 109 1024 14 10 57 2048 14 10 29 4096 10 15 x 150 Radiometric performances at maximum pixel rate Dynamic range bits Spectral range nm Linearity % Gain range (step of 0.047dB) dB Gmin 0 12 (also configurable in 8 or 10) 250 - 1100 << 1% Gnom 18 Gmax 30 Peak response (typical) 14m pitch LSB/nJ/cm 10m pitch LSB/nJ/cm 130 50 1040 400 4180 1600 Output RMS noise SNR Effective bits (typical) dB bits 67.4 11.2 49 8.2 37 6.2 Input RMS Noise 14m pitch 10m pitch (typical) pJ/cm pJ/cm 14 37 Mechanical & electrical interface Size (w x h x l) mm 56 x 60 x 38.6 Lens mount C, F, K Sensor alignment (refer to 8.4) x,y= 50 m x,y= 0.2 m z= 0-30 m tiltz= 0-35 m Power supply V DC, single 12 to 24 V Power dissipation W <8 Operating temperature C 0 to 55 (non condensing) Storage temperature C 0 to 75 (non condensing) Spectral response relative response (%) pixel 10x10 m 100% 80% 60% 40% 20% 0% 200 07 FEB 2002 pixel 14x14 m 400 600 800 wave length (nm) 1000 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 3/15 2. CAMERA DESCRIPTION Power supplies DC power TM CameraLink transceiver Even pixels analog chain PGA, CDS, ADC 12 bits @ 30Mpixels/s Data Stobe, LVAL Sequencer Controller TX CameraLink I/F Trigger TM RX Linear CCD 2 taps Odd pixels analog chain PGA, CDS, ADC 12 bits @ 30Mpixels/s Ext CLK CCD Drivers Serial line Microcontroller Figure 2 - Camera synoptic The camera is based on a two taps linear CCD. Therefore, two analog chains process odd and even pixels of the linear sensor. The analog chains performed the CCD output processing. It encompasses the correlated double sampling (CDS), the dark level correction (dark pixel clamping), the gain (PGA) and offset correction and finally the analog to digital conversion on 12 bits. Note : PGA stands for programmable gain array The camera is supplied by a single DC power voltage from 12 to 24 V. TM The functional interface (data and control) is provided by the CameraLink TM The camera uses the base configuration of Cameralink standard. Note : DVAL=1 and FVAL=0 interface. The data can be provided on two channels or in a single multiplexed channel. The data format can be configured in 8, 10 or 12 bits. The camera can be used with external triggers (TRIG1 and TRIG2 signals) in different trigger modes (refer to 5.1). The camera can be also clocked externally, allowing system synchronisation and/or multi-camera synchronisation. The camera configuration and settings is performed via a serial line. This interface is used for : * Gain, offset setting * Dynamic range, data rate setting * Trigger mode setting : free run or external trigger modes * Integration time setting : in free running & external trigger mode 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 4/15 3. STANDARD CONFORMITY The cameras have been tested in the following conditions : * Shielded power supply cable * CameraLink data transfer cable ref. 14B26-SZLB-500-OLC (3M) * Linear AC-DC power supply We recommend to use the same configuration to ensure the compliance with the following standards. 3.1 CE CONFORMITY AVIIVA Cameras complies with the European directive 89/336/CEE (EN 50081-2, EN 61000-6-2) 3.2 FCC CONFORMITY AVIIVA Cameras complies with Part 15 of FCC rules. Operation is subject to the following two conditions : * This device may not cause harmful interference, and * This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 5/15 4. CAMERA COMMAND AND CONTROL Camera configuration is set by the serial interface. Please refer to 6.4 for the detailed protocol of the serial line. Setting Command Parameter Configuration record E= Gain (1) Data transfer (2) G= H= Output format (3) S= Pattern (4) T= Integration Time Trigger mode I= M= Even data Offset (5) Odd data Offset (5) Special commands O= P= != User camera ID $= 0 1 0 to 851 0 1 3 5 6 7 8 9 0 1 2 0 1 5 to 13000 1 2 3 4 0 to 15 0 to 15 0 1 2 3 4 5 String of Char. Description The camera configuration is recorded on each change The camera configuration is recorded only on request Gain setting from 0 to 40 dB (~0.047dB steps) Two outputs on external clock One output (multiplexed) on external clock One output (multiplexed) at 20MHz data rate One output (multiplexed) at 30MHz data rate Two outputs at 20MHz data rate One output (multiplexed) at 40MHz data rate Two outputs at 30MHz data rate One output (multiplexed) at 60MHz data rate 12 bits Output data 10 bits Output data 8 bits Output data Standard Pattern Integration time (s) in free run or external triggered mode Free run with integration time setting (see timing diagram) External trigger with integration time setting (see timing diagram) Trigger and Integration time controlled Trigger and integration time controlled by two inputs Even Offset setting from 0 to approx. 200 LSB Odd Offset setting from 0 to approx. 200 LSB Camera identification readout User camera identification readout Software version readout Camera configuration readout Current camera configuration record Default camera configuration restoration Writing and record of the user camera identification (1) Camera gain (dB) = G x 0.047 (2) Commands "H=2" and "H=4" will give 10 and 15MHz data rate which are not compatible with Camera Link standard. Please don't use it. (3) The pinout corresponding to this options is fully compatible with the Camera Link standard (see par. 7) (4) The pattern is useful to check if the interfacing is well done. You should see a jagged image of 255 pixels steps. (5) The offset is set in manufacturing to balance both the channels. The initial setting is about 8 (~ 130 LSB). In some cases, you may have to change it (for example if the ambient temperature is very high). 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 6/15 5. TIMING 5.1 SYNCHRONISATION MODE Four different modes may be used under user control. The TRIG1 and TRIG2 signals may be used to trigger an external event and to control the integration time. The Master clock is either external or internal clock. 5.1.1 FREE RUN MODE WITH INTEGRATION TIME SETTING The integration and readout periods start automatically and immediately after the previous period. *The Integration time is set by the serial line and should be higher than the read-out time (otherwise it is adjusted to the readout time). The read-out time depends on pixel number and pixel rate. Label Description ti Integration time duration tg Consecutive integration period gap (at maximum frequency) tt Integration period to read-out delay Min * Typ Max 13 ms 6 s 1 s tt READOUT N READOUT N-1 INTEGRATION N+1 INTEGRATION N tg ti 5.1.2 TRIGGERED MODE WITH INTEGRATION TIME SETTING The integration period starts immediately after the rising edge of TRIG1 input signal. The Integration time is set by the serial line. This integration period is immediately followed by a readout period. The read-out time depends on pixel number and the pixel rate. Label ti td tt ts th Description Integration time duration TRIG1 rising to integration period delay Integration period to read-out delay Integration period to TRIG1 rising set-up time TRIG1 hold time (pulse high duration) Min 5 s Typ Max 13 ms 5.5 s 1 s 4 s 1 s ti ts td th tt TRIG1 INTEGRATION N INTEGRATION N+1 READOUT N 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 7/15 5.1.3 TRIGGED AND INTEGRATION TIME CONTROLLED The integration period starts immediately after the falling edge of TRIG1 input signal. The integration period stops immediately after the rising edge of TRIG1 input signal. This integration period is immediately followed by a readout period. The read-out time depends on pixel number and pixel rate. Label ti td1 td2 tt th Description Integration time duration TRIG1 rising to integration period delay TRIG2 rising to integration period delay Integration period to read-out delay TRIG1 hold time (pulse high duration) th Min 5 s Typ Max 100 ns 1.3 s 1 s 1 s ti TRIG1 td1 td2 READOUT N-1 READOUT N INTEGRATION N INTEGRATION N+1 tt 5.1.4 TRIGGER AND INTEGRATION TIME CONTROLLED BY TWO INPUTS TRIG2 rising edge start the integration period. TRIG1 rising edge stop the integration period. This period is immediately followed by a readout period. Label ti td1 td2 tt th Description Integration time duration TRIG2 rising to integration period delay TRIG1 rising to integration period delay Integration period to read-out delay TRIG1 & TRIG2 hold time (pulse high duration) Min 5 s Typ Max 100 ns 1.3 s 1 s 1 s ti TRIG2 td1 td2 TRIG1 INTEGRATION N INTEGRATION N+1 READOUT N-1 READOUT N tt 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 8/15 5.2 OUTPUT DATA TIMING This timing correspond to the input data of the "Chanel Link" interface. The camera output data are not detailed here because fully compliant with the Camera Link standard (serial high speed interface) Label Description Min tp Input falling edge to output clock propagation delay td STROBE to synchronised signals delay Internal Clock or CLOCK_IN Typ Max 7 ns -5 ns +5 ns tp LVAL td STROBE DATA Fist valid pixel Last valid pixel Note : CLOCK_IN Input must stay between 5 to 60MHz. Out of this range, the performances may be decreased. 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 9/15 6. ELECTRICAL INTERFACE 6.1 POWER SUPPLY It is recommended to insert a 1A fuse between the power supply and the camera. Signal name PWR GND I/O Type P - DC power input : +12V to +24V (+-0.5V) Description P - Electrical and Mechanical ground I = input, O = output, IO = bi-directional signal, P = power/ground, NC = not connected 6.2 CAMERA CONTROL TM The CameraLink interface provides four LVDS signals dedicated to camera control (CC1 to CC4). On the AVIIVA, three of them are used to synchronise the camera on external events. Signal name I/O Type TRIG1 I RS644 CC1 - Synchronisation input (refer to 5.1) TRIG2 I RS644 CC2 - Start Integration period in dual synchro mode (refer to 5.1) I RS644 CC4 - External clock for (multi-)camera synchronisation (refer to 5.1) CLOCK_IN Description I = input, O = output, IO = bi-directional signal, P = power/ground, NC = not connected Note : CC3 is not used. 6.3 VIDEO DATA Data and enable signals are provided on the CameraLinkTM interface I/O Type ODD[11-0] Signal name O RS644 Odd pixel data (refer to 5.2), ODD-00 = LSB, ODD-11 = MSB EVEN[11-0] O RS644 Even pixel data (refer to 5.2), EVEN-00 = LSB, EVEN-11 = MSB STROBE O RS644 Output data clock. (refer to 5.2), data valid on the rising edge O RS644 Line valid (refer to 5.2), active high signal LVAL Description I = input, O = output, IO = bi-directional signal, P = power/ground, NC = not connected TM Notes : FVAL, as defined in the CameraLink standard, is not used. FVAL is permanently tied to 0 (low) level. DVAL is not used. DVAL is permanently tied to 1 (high) level. In case of Single output, the data (multiplexed) are output in place of Odd data. 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 10/15 6.4 SERIAL COMMUNICATION The CameraLinkTM interface provides two LVDS signal pairs for the communication between the camera and the frame grabber. This is an asynchronous serial communication based on RS-232 protocol. The configuration of the serial line is : * Full duplex / without handshaking * 9600 bauds, 8 bits data, no parity bit, 1 stop bit. Signal name I/O Type Description SerTFG O RS644 Differential pair for serial communication to the frame grabber SerTC I RS644 Differential pair for serial communication from the frame grabber Command syntax The valid syntax is : "S=n(CR)" with : S : command identification as per 4. S is a single character in upper case. n : setting value. (CR) : means "carriage return". no spaces, nor tabs may be inserted between S, =, n and (CR). example of a valid command : G=3(CR) : sets the camera to gain 3 (refer to 4 for exact value calculation) example of non valid commands : G = 3(CR) : spaces g=3(CR) : g instead of G G=1040(CR) : 1040 is outside of range. Command processing Each command received by the camera is processed : if the command is valid : * the setting is done in case of a write command * the camera returns the data separated by (CR) in case of the read command * the camera returns : >OK(CR) if the command is not valid : * nothing is done. * the camera returns : >1 = out of range ; >2 = syntax error ; >3 = command too long ; >4,>6,>7 = internal error ; >5 undefined function example : when receiving "!=3(CR)'' the camera returns its current settings : A=0(CR) B=0(CR) .... E=0(CR) >OK(CR) 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 11/15 7. CONNECTOR DESCRIPTION All connectors are on the rear panel. Note : cables for digital signals shall be shielded twisted pairs. 7.1 POWER SUPPLY Camera connector type : Hirose HR10A-7R-6PB (male) Cable connector type : Hirose HR10A-7P-6S (female) Signal Pin Signal Pin PWR 1 GND 4 PWR 2 GND 5 PWR 3 GND 6 1 6 5 2 3 4 Receptacle viewed from camera back 7.2 CAMERALINKTM CONNECTOR Standard Cameralink TM cable shall be used to ensure the full electrical compatibility. Camera connector type : MDR-26 (female) ref. 10226-2210VE TM Cable connector type : Standard CameraLink cable shall be used (ex. 3M - 14B26-SZLB-x00-OLC) Signal Pin Signal Pin GND 1 GND 14 X0- 2 X0+ 15 X1- 3 X1+ 16 X2- 4 X2+ 17 Xclk- 5 Xclk+ 18 X3- 6 X3+ 19 SerTC+ 7 SerTC- 20 SerTFG- 8 SerTFG+ 21 CC1- 9 CC1+ 22 CC2+ 10 CC2- 23 CC3- 11 CC3+ 24 CC4+ 12 CC4- 25 GND 13 GND 26 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 12/15 Bit Assignments This bit assignment is compliant with the CameraLinkTM Specification in the Base Configuration. In "single output" mode (multiplexed), the data are output on ODD-xx bits. When used in 12 bits data (S=0) Bit DS90CR285 pin name Bit DS90CR285 pin name Bit DS90CR285 pin name Bit DS90CR285 pin name ODD-00 Tx0 ODD-07 Tx5 EVEN-02 Tx19 EVEN-09 Tx14 ODD-01 Tx1 ODD-08 Tx7 EVEN-03 Tx20 EVEN-10 Tx10 ODD-02 Tx2 ODD-09 Tx8 EVEN-04 Tx21 EVEN-11 Tx11 ODD-03 Tx3 ODD-10 Tx9 EVEN-05 Tx22 STROBE TxCLK ODD-04 Tx4 ODD-11 Tx12 EVEN-06 Tx16 LVAL Tx24 ODD-05 Tx6 EVEN-00 Tx15 EVEN-07 Tx17 ODD-06 Tx27 EVEN-01 Tx18 EVEN-08 Tx13 DS90CR285 pin name Bit DS90CR285 pin name Bit DS90CR285 pin name When used in 10 bits data (S=1) Bit DS90CR285 pin name Bit ODD-00 Tx0 ODD-07 Tx5 EVEN-02 Tx19 EVEN-09 Tx14 ODD-01 Tx1 ODD-08 Tx7 EVEN-03 Tx20 NC Tx10 ODD-02 Tx2 ODD-09 Tx8 EVEN-04 Tx21 NC Tx11 ODD-03 Tx3 NC Tx9 EVEN-05 Tx22 STROBE TxCLK ODD-04 Tx4 NC Tx12 EVEN-06 Tx16 LVAL Tx24 ODD-05 Tx6 EVEN-00 Tx15 EVEN-07 Tx17 ODD-06 Tx27 EVEN-01 Tx18 EVEN-08 Tx13 When used in 8 bits data (S=2) Bit DS90CR285 pin name Bit DS90CR285 pin name Bit DS90CR285 pin name Bit DS90CR285 pin name ODD-00 Tx0 ODD-07 Tx5 NC Tx19 EVEN-05 Tx14 ODD-01 Tx1 EVEN-00 Tx7 NC Tx20 EVEN-06 Tx10 ODD-02 Tx2 EVEN-01 Tx8 NC Tx21 EVEN-07 Tx11 ODD-03 Tx3 EVEN-02 Tx9 NC Tx22 STROBE TxCLK ODD-04 Tx4 EVEN-03 Tx12 NC Tx16 LVAL Tx24 ODD-05 Tx6 NC Tx15 NC Tx17 ODD-06 Tx27 NC Tx18 EVEN-04 Tx13 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 13/15 8. MECHANICAL CHARACTERISTICS 8.1 WEIGHT The camera typical weight (without lens nor lens adapter) is 220 g (typical) 8.2 DIMENSIONS The camera dimension (without lens) are W = 56 mm, H = 60 mm, L = 38.6 mm Reference mounting surface 38.6 Mechanical reference point 56 12 1 y= 300.05 15 Sensor 60 st 1 pixel 15 Reference mounting surface Reference mounting surface x= refer to the table in 8.3 46 4 x M3 6 42 H7 4 x 2 holes M4 (on the 4 sides) 3 x M2.5 at 120 Y axis X,Y plan z=10.3 -0/+0.03 Optical sensor surface to front face X axis Z axis All dimensions in millimeters Figure 3 - Mechanical Box drawing and dimensions 8.3 MECHANICAL MOUNTING REFERENCE The front panel mechanical part is design to support the mounting of the camera. On this mechanical part, three surfaces are considered as mounting reference surface : i.e. the distance between these surfaces and the first active pixel are known very precisely (better than 50m). Number of pixel 512 x in 14m sensor (nm) 24.416 20.832 13.664 - x in 10m sensor (nm) - 22.880 17.760 7.520 07 FEB 2002 1024 2048 4096 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 14/15 8.4 SENSOR ALIGNEMENT First active pixel center Y axis x + x x,y active area Mechanical reference point y + y X axis Z axis active area center tiltz Mechanical reference point z + z x X, Y plans Figure 4 - Sensor alignment diagram 8.5 LENS MOUNTING (LENS NOT SUPPLIED) The camera can be provided with three different lens adapter, corresponding to three different options. It is up to the customer to selected the correct adapter. The following table gives recommendation depending on the sensor size Number of pixel 512 / 14m C mount OK 1024 / 10m 1024 / 14m 2048 / 10m 2048 / 14m 4096 / 10m OK OK not usable not usable not usable F mount OK OK OK OK OK OK K mount OK OK OK OK OK OK 8.6 HEAT-SINK MOUNTING In order to improve the power dissipation, the camera can be delivered with heat-sink to be mounted by the user on the side faces of the camera. The delivery of the heat-sinks corresponds to a dedicated option. 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4 AVIIVA CameraLinkTM 15/15 ORDERING CODE Part Number Resolution Pixels size Description AT71LKLB1K0F-BAA 1K 10 m AVIIVA camera (without any mount) AT71LKLB2K0F-BAA 2K 10 m AVIIVA camera (without any mount) AT71LKLB4K0F-BAA 4K 10 m AVIIVA camera (without any mount) AT71LKLB0K5K-BAA 512 14 m AVIIVA camera (without any mount) AT71LKLB1K0K-BAA 1K 14 m AVIIVA camera (without any mount) AT71LKLB2K0K-BAA 2K 14 m AVIIVA camera (without any mount) AT71KFPAVIVA-ABA F mount (NIKON) AT71KFPAVIVA-ACA C mount AT71KFPAVIVA-AKA K mount (PENTAX) AT71KAVIVAP2C0D3A0 Cables kit : 10m power supply & 5m Camera Link cables Information furnished is believed to be accurate and reliable. However Atmel- assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent rights of Atmel-. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. Atmel- products are not authorised for use as critical components in life support devices or systems without express written approval from Atmel-. (c) 2002 Atmel-GFO- Printed in France - All rights reserved. This product is manufactured by Atmel-GFO- 38521 SAINT-EGREVE - FRANCE. For further information please contact : ATMEL 2, allee Maryse Bastie Z.I. d'Orlytech 91781 WISSOUS Cedec - FRANCE Phone +33 (0)1 49 75 96 00 - Fax +33 (0) 1 49 75 96 01 - Internet : http://www.atmel.com 07 FEB 2002 www.atmel.com Germany : Phone +49 (0)89 95 90 94-0 - Fax +49 (0)89 95 90 94-44 - USA : Phone +1 (973) 812 9040- Fax +1 (973) 812 4191 For other countries, please contact, France : Phone +33 (0)1 49 75 96 00 - Fax +33 (0)1 49 75 96 01 Issue 2.4