TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
High Slew Rate . . . 10.5 V/µs Typ
D
High-Gain Bandwidth . . . 5.1 MHz Typ
D
Supply Voltage Range 2.5 V to 5.5 V
D
Rail-to-Rail Output
D
360 µV Input Offset Voltage
D
Low Distortion Driving 600-Ω
0.005% THD+N
D
1 mA Supply Current (Per Channel)
D
17 nV/√Hz Input Noise Voltage
D
2 pA Input Bias Current
D
Characterized From TA = –55°C to 125°C
D
Available in MSOP and SOT-23 Packages
D
Micropower Shutdown Mode ...I
DD < 1 µA
D
Available in Q-Temp Automotive
High Reliability Automotive Applications
Configuration Control / Print Support
Qualification to Automotive Standards
description
The TLV277x CMOS operational amplifier family combines high slew rate and bandwidth, rail-to-rail output
swing, high output drive, and excellent dc precision. The device provides 10.5 V/µs of slew rate and 5.1 MHz
of bandwidth while only consuming 1 mA of supply current per channel. This ac performance is much higher
than current competitive CMOS amplifiers. The rail-to-rail output swing and high output drive make these
devices a good choice for driving the analog input or reference of analog-to-digital converters. These devices
also have low distortion while driving a 600-Ω load for use in telecom systems.
These amplifiers have a 360-µV input offset voltage, a 17 nV/√Hz input noise voltage, and a 2-pA input bias
current for measurement, medical, and industrial applications. The TLV277x family is also specified across an
extended temperature range (–40°C to 125°C), making it useful for automotive systems, and the military
temperature range (–55°C to 125°C), for military systems.
These devices operate from a 2.5-V to 5.5-V single supply voltage and are characterized at 2.7 V and 5 V. The
single-supply operation and low power consumption make these devices a good solution for portable
applications. The following table lists the packages available.
FAMILY PACKAGE TABLE
DEVICE
NUMBER
OF
PACKAGE TYPES
SHUTDOWN
UNIVERSAL
DEVICE
OF
CHANNELS PDIP CDIP SOIC SOT-23 TSSOP MSOP LCCC CPAK
SHUTDOWN
EVM BOARD
TLV2770 1 8 — 8 — — 8 — — Yes
TLV2771 1 — — 8 5 — — — — —
TLV2772 2 8 8 8 — 8 8 20 10 — Refer to the EVM
Selection Guide
TLV2773 2 14 — 14 — — 10 — — Yes
S
e
l
ec
ti
on
G
u
id
e
(
Lit#
S
L
OU060)
TLV2774 4 14 — 14 — 14 — — — —
(Lit#
SLOU060)
TLV2775 4 16 — 16 — 16 — — — Yes
A SELECTION OF SINGLE-SUPPLY OPERATIONAL AMPLIFIER PRODUCTS†
DEVICE VDD
(V) BW
(MHz) SLEW RATE
(V/µs) IDD (per channel)
(µA) RAIL-TO-RAIL
TLV277X 2.5 – 6.0 5.1 10.5 1000 O
TLV247X 2.7 – 6.0 2.8 1.5 600 I/O
TLV245X 2.7 – 6.0 0.22 0.11 23 I/O
TLV246X 2.7 – 6.0 6.4 1.6 550 I/O
†All specifications measured at 5 V.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
This document contains information on products in more than one phase
of development. The status of each device is indicated on the page(s)
specifying its electrical characteristics.
Copyright 2001, Texas Instruments Incorporated
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLV2770 and TLV2771 AVAILABLE OPTIONS
VIOmax AT 25
°
C
PACKAGED DEVICES
TA
V
IO
max
AT
25°C
(mV) SMALL OUTLINE
(D) SOT-23
(DBV) MSOP
(DGK) PLASTIC DIP
(P)
0°C to 70°C 2.5 TLV2770CD
TLV2771CD —
TLV2771CDBV TLV2770CDGK†
—TLV2770CP
—
40°Cto125°C
2.5 TLV2770ID
TLV2771ID —
TLV2771IDBV TLV2770IDGK†
—TLV2770IP
—
–
40°C
to
125°C
1.6 TLV2770AID
TLV2771AID —
——
—TLV2770AIP
—
†This device is in the Product Preview stage of development. Please contact your local TI sales office for availability.
TLV2772 and TL V2773 AVAILABLE OPTIONS
VIOmax AT 25°C
PACKAGED DEVICES
TA
V
IO
max
AT
25°C
(mV) SMALL OUTLINE
(D) MSOP
(DGK) MSOP
(DGS) PLASTIC DIP
(N) PLASTIC DIP
(P)
0°C to 70°C 2.5 TLV2772CD
TLV2773CD TLV2772CDGK
——
TLV2773CDGS —
TLV2773CN TLV2772CP
—
40
°
Cto125
°
C
2.5 TLV2772ID
TLV2773ID TLV2772IDGK
——
TLV2773IDGS —
TLV2773IN TLV2772IP
—
–
40°C
to
125°C
1.6 TLV2772AID
TLV2773AID —
——
——
TLV2773AIN TLV2772AIP
—
TLV2774 and TL V2775 AVAILABLE OPTIONS
VIOmax AT 25°C
PACKAGED DEVICES
TA
V
IO
max
AT
25°C
(mV) SMALL OUTLINE
(D) PLASTIC DIP
(N) PLASTIC DIP
(P) TSSOP
(PW)
0°C to 70°C 2.7 TLV2774CD
TLV2775CD —
TLV2775CN TLV2774CP
—TLV2774CPW
TLV2775CPW
40°Cto125°C
2.7 TLV2774ID
TLV2775ID —
TLV2775IN TLV2774IP
—TLV2774IPW
TLV2775IPW
–
40°C
to
125°C
2.1 TLV2774AID
TLV2775AID —
TLV2775AIN TLV2774AIP
—TLV2774AIPW
TLV2775AIPW
TLV2772M/Q AND TLV2772AM/Q AVAILABLE OPTIONS
PACKAGED DEVICES
TAVIOmax AT 25°C
(mV) SMALL
OUTLINE
(D)
CHIP CARRIER
(FK) CERAMIC DIP
(JG)
CERAMIC
FLATPACK
(U)
TSSOP
(PW)
40°Cto125°C
2.5 TLV2772QD‡———TLV2772QPW‡
–
40°C
to
125°C
1.6 TLV2772AQD‡———TLV2772AQPW‡
55°Cto125°C
2.5 TLV2772MD TLV2772MFK TLV2772MJG TLV2772MU —
–
55°C
to
125°C
1.6 TLV2772AMD TLV2772AMFK TLV2772AMJG TLV2772AMU —
‡Available in tape and reel
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE SYMBOLS
PACKAGE TYPE PINS PART NUMBER SYMBOL†
SOT23
5 Pin
TLV2771CDBV VAMC
SOT23
5
Pin
TLV2771IDBV VAMI
TLV2770CDGK xxTIABO
8 Pin
TLV2770IDGK xxTIABP
MSOP
8
Pin
TLV2772CDGK xxTIAAF
MSOP
TLV2772IDGK xxTIAAG
10 Pin
TLV2773CDGS xxTIABQ
10
Pin
TLV2773IDGS xxTIABR
†xx represents the device date code.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLV277x PACKAGE PINOUTS
1
2
3
4
5
10
9
8
7
6
1OUT
1IN–
1IN+
GND
1SHDN
VDD
2OUT
2IN–
2IN+
2SHDN
3
2
4
5
(TOP VIEW)
1
OUT
GND
IN+
VDD
IN–
TLV2771
DBV PACKAGE
TLV2773
DGS PACKAGE
(TOP VIEW)
NC – No internal connection
1
2
3
4
8
7
6
5
1OUT
1IN–
1IN+
GND
VDD
2OUT
2IN–
2IN+
TLV2772
D, DGK, JG, P, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
NC
IN–
IN+
GND
SHDN
VDD
OUT
NC
TLV2770
D, DGK† OR P PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
NC
IN–
IN+
GND
NC
VDD
OUT
NC
TLV2771
D PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN–
1IN+
GND
NC
1SHDN
NC
VDD
2OUT
2IN–
2IN+
NC
2SHDN
NC
(TOP VIEW)
TLV2773
D OR N PACKAGE
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN–
1IN+
VDD
2IN+
2IN–
2OUT
4OUT
4IN–
4IN+
GND
3IN+
3IN–
3OUT
(TOP VIEW)
TLV2774
D, N, OR PW PACKAGE
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
VDD
2IN+
2IN–
2OUT
1/2SHDN
4OUT
4IN–
4IN+
GND
3IN+
3IN–
3OUT
3/4SHDN
(TOP VIEW)
TLV2775
D, N, OR PW PACKAGE
NC
VDD +
2OUT
2IN –
2IN +
NC
1OUT
1IN –
1IN +
GND
1
2
3
4
5
10
9
8
7
6
(TOP VIEW)
TLV2772M AND TLV2772AM
U PACKAGE
3 2 1 20 19
910111213
4
5
6
7
8
18
17
16
15
14
NC
2OUT
NC
2IN–
NC
NC
1IN–
NC
1IN+
NC
NC
1OUT
NC
2IN+
NC NC
NC
NC VDD+
TLV2772M AND TLV2772AM
FK PACKAGE
(TOP VIEW)
GND
†This device is in the Product Preview stage of development. Please contact your local TI sales office for availability.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD (see Note 1) 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage, VID (see Note 2) ±VDD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (any input, see Note 1) –0.3 V to VDD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input current, II (any input) ±4 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, IO ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current into VDD+ ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current out of GND ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duration of short-circuit current (at or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M suffix –55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only , and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may af fect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to GND.
2. Differential voltages are at the noninverting input with respect to the inverting input. Excessive current flows when input is brought
below GND – 0.3 V.
3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
DISSIPATION RATING TABLE
PACKAGE
T
A
≤ 25°CDERATING F ACTOR T
A
= 70°C T
A
= 85°C T
A
= 125°C
PACKAGE
A
POWER RATING ABOVE TA = 25°C
A
POWER RATING
A
POWER RATING
A
POWER RATING
D725 mW 5.8 mW/°C464 mW 377 mW 145 mW
DBV 437 mW 3.5 mW/°C280 mW 227 mW 87 mW
DGK 424 mW 3.4 mW/°C271 mW 220 mW 85 mW
DGS 424 mW 3.4 mW/°C271 mW 220 mW 85 mW
FK 1375 mW 11.0 mW/°C672 mW 546 mW 210 mW
JG 1050 mW 8.4 mW/°C880 mW 714 mW 275 mW
N1150 mW 9.2 mW/°C736 mW 598 mW 230 mW
P1000 mW 8.0 mW/°C640 mW 520 mW 200 mW
PW 700 mW 5.6 mW/°C448 mW 364 mW 140 mW
U675 mW 5.4 mW/°C432 mW 350 mW 135 mW
recommended operating conditions
C SUFFIX I SUFFIX Q SUFFIX M SUFFIX
UNIT
MIN MAX MIN MAX MIN MAX MIN MAX
UNIT
Supply voltage, VDD 2.5 6 2.5 6 2.5 6 2.5 6 V
Input voltage range, VIGND VDD+ –1.3 GND VDD+ –1.3 GND VDD+ –1.3 GND VDD+ –1.3 V
Common-mode input voltage, VIC GND VDD+ –1.3 GND VDD+ –1.3 GND VDD+ –1.3 GND VDD+ –1.3 V
Operating free-air temperature, TA0 70 –40 125 –40 125 –55 125 °C
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 2.7 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLV277xC
UNIT
PARAMETER
TEST
CONDITIONS
T
A
†
MIN TYP MAX
UNIT
TLV2770/1/2
25°C 0.44 2.5
VIO
In
p
ut offset voltage
TLV2770/1/2
VIC = 0, V
O
= 0, Full range 0.47 2.7
mV
V
IO
Input
offset
voltage
TLV2773/4/5
IC
RS = 50 Ω,
O,
VDD = ±1.35 V 25°C0.8 2.7
mV
TLV2773/4/5
Full range 0.86 2.9
αVIO
Temperature coefficient of input 25°C to
2
µV/
°
C
αVIO offset voltage 125°C
2
µ
V/°C
IIO
In
p
ut offset current
V
IC
= 0, V
O
= 0
,
25°C 1 60 p
A
I
IO
Input
offset
current
IC ,
RS = 50 Ω
VO
0,
VDD = ±1.35 V Full range 2 100
pA
IIB
In
p
ut bias current
25°C 2 60 p
A
I
IB
Input
bias
current
Full range 6 100
pA
VICR
Common-mode input volta
g
e
CMRR>70dB
RS=50Ω
25°C0
to 1.4 –0.3
to 1.7
V
V
ICR
g
range
CMRR
>
70
dB
,
R
S =
50
Ω
Full range 0
to 1.4 –0.3
to 1.7
V
IOH = 0 675 mA
25°C 2.6
VOH
High level out
p
ut voltage
I
OH = –
0
.
675
mA
Full range 2.5
V
V
OH
High
-
level
output
voltage
IOH =22mA
25°C 2.4
V
I
OH = –
2
.
2
mA
Full range 2.1
VIC = 1 35 V
IOL = 0 675 mA
25°C 0.1
VOL
Low level out
p
ut voltage
V
IC =
1
.
35
V
,
I
OL =
0
.
675
mA
Full range 0.2
V
V
OL
Low
-
level
output
voltage
VIC = 1 35 V
IOL =22mA
25°C 0.21
V
V
IC =
1
.
35
V
,
I
OL =
2
.
2
mA
Full range 0.6
AVD
Lar
g
e-si
g
nal differential volta
g
e V
IC
= 1.35 V, R
L
= 10 kΩ,25°C 20 380
V/mV
A
VD
gg g
amplification
IC ,
VO = 0.6 V to 2.1 V
L,
Full range 13
V/mV
ri(d) Differential input resistance 25°C 1012 Ω
ci(c) Common-mode input capacitance f = 10 kHz 25°C 8 pF
zoClosed-loop output impedance f = 100 kHz, AV = 10 25°C 25 Ω
CMRR
Common mode rejection ratio
V
IC
= 0 to 1.5 V, V
O
= 1.5 V, 25°C 70 84
dB
CMRR
Common
-
mode
rejection
ratio
IC ,
RS = 50 Ω
O,
Full range 70 82
dB
kSVR
Suppl
y
volta
g
e rejection ratio V
DD
= 2.7 V to 5 V, V
IC
= V
DD
/2, 25°C 70 89
dB
k
SVR
ygj
(∆VDD /∆VIO)
DD ,
No load
IC DD ,
Full range 70 84
dB
IDD
Su
pp
ly current (
p
er channel)
VO=15V
No load
25°C 1 2
mA
I
DD
Supply
current
(per
channel)
V
O =
1
.
5
V
,
No
load
Full range 2
mA
IDD(SHDN)
Supply current in shutdown (per 25°C 0.8 1.5
µA
I
DD(SHDN)
y(
channel) Full range 1.3 2 µ
A
Tlt
TLV2770 1.47
V
(
ON
)
T urnon voltage
level
TLV2773 AV = 5 25°C1.43 V
()
level
TLV2775 1.40
Tfflt
TLV2770 1.27
V
(
OFF
)
T urnoff voltage
level
TLV2773 AV = 5 25°C1.21 V
()
level
TLV2775 1.20
†Full range is 0°C to 70°C.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 2.7 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLV277xC
UNIT
PARAMETER
TEST
CONDITIONS
T
A
†
MIN TYP MAX
UNIT
VO(PP) =08V
CL= 100
p
F
25°C5 9
SR Slew rate at unity gain
V
O(PP) =
0
.
8
V
,
RL = 10 kΩ
C
L =
100
pF
,Full
range 4.7 6 V/µs
V
Equivalent in
p
ut noise voltage
f = 1 kHz 25°C 21
nV/√Hz
V
n
Equivalent
input
noise
voltage
f = 10 kHz 25°C 17 n
V/√H
z
VN(PP)
Peak to
p
eak equivalent in
p
ut noise voltage
f = 0.1 Hz to 1 Hz
25°C
0.33
µV
V
N(PP)
Peak
-
to
-
peak
equivalent
input
noise
voltage
f = 0.1 Hz to 10 Hz
25°C
0.86 µ
V
InEquivalent input noise current f = 100 Hz 25°C 0.6 fA/√Hz
R 600 Ω
AV = 1 0.0085%
THD + N Total harmonic distortion plus noise RL = 600 Ω,
f=1kHz
AV = 10 25°C0.025%
f
=
1
kHz
AV = 100 0.12%
Gain-bandwidth product f = 10 kHz,
CL = 100 pF RL = 600 Ω,25°C 4.8 MHz
t
Settling time
AV = –1,
Step = 1 V, 0.1% 25°C 0.186
µs
t
s
Settling
time
,
RL = 600 Ω,
CL = 100 pF 0.01% 25°C 0.3 µ
s
φmPhase margin at unity gain
RL= 600 Ω
CL= 100
p
F
25°C 46°
Gain margin
R
L =
600
Ω
,
C
L =
100
pF
25°C 12 dB
†Full range is 0°C to 70°C.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLV277xC
UNIT
PARAMETER
TEST
CONDITIONS
T
A
†
MIN TYP MAX
UNIT
TLV2770/1/2
25°C 0.36 2.5
VIO
In
p
ut offset voltage
TLV2770/1/2
VIC = 0, V
O
= 0, Full range 0.4 2.7
mV
V
IO
Input
offset
voltage
TLV2773/4/5
IC
RS = 50 Ω
O,
VDD = ±2.5 V 25°C0.7 2.5
mV
TLV2773/4/5
Full range 0.78 2.7
αVIO
Temperature coefficient of input 25°C to
2
µV/°C
αVIO offset voltage 125°C
2
µ
V/°C
IIO
In
p
ut offset current
V
IC
= 0, V
O
= 0
,
25°C 1 60 p
A
I
IO
Input
offset
current
IC ,
RS = 50 Ω
VO
0,
VDD = ±2.5 V Full range 2 100
pA
IIB
In
p
ut bias current
25°C 2 60 p
A
I
IB
Input
bias
current
Full range 6 100
pA
VICR
Common mode in
p
ut voltage range
CMRR>60dB
RS=50Ω
25°C0
to 3.7 –0.3
to 3.8
V
V
ICR
Common
-
mode
input
voltage
range
CMRR
>
60
dB
,
R
S =
50
Ω
Full range 0
to 3.7 –0.3
to 3.8
V
IOH =13mA
25°C 4.9
VOH
High level out
p
ut voltage
I
OH = –
1
.
3
mA
Full range 4.8
V
V
OH
High
-
level
output
voltage
IOH =42mA
25°C 4.7
V
I
OH = –
4
.
2
mA
Full range 4.4
VIC =25V
IOL =13mA
25°C 0.1
VOL
Low level out
p
ut voltage
V
IC =
2
.
5
V
,
I
OL =
1
.
3
mA
Full range 0.2
V
V
OL
Low
-
level
output
voltage
VIC =25V
IOL =42mA
25°C 0.21
V
V
IC =
2
.
5
V
,
I
OL =
4
.
2
mA
Full range 0.6
AVD
Lar
g
e-si
g
nal differential volta
g
e V
IC
= 2.5 V, R
L
= 10 kΩ,25°C 20 450
V/mV
A
VD
gg g
amplification
IC ,
VO = 1 V to 4 V
L,
Full range 13
V/mV
ri(d) Differential input resistance 25°C 1012 Ω
ci(c) Common-mode input capacitance f = 10 kHz 25°C 8 pF
zoClosed-loop output impedance f = 100 kHz, AV = 10 25°C 20 Ω
CMRR
Common mode rejection ratio
V
IC
= 0 to 3.7 V, V
O
= 3.7 V, 25°C 60 96
dB
CMRR
Common
-
mode
rejection
ratio
IC ,
RS = 50 Ω
O,
Full range 60 93
dB
kSVR
Suppl
y
volta
g
e rejection ratio V
DD
= 2.7 V to 5 V, V
IC
= V
DD
/2, 25°C 70 89
dB
k
SVR
ygj
(∆VDD /∆VIO)
DD ,
No load
IC DD ,
Full range 70 84
dB
IDD
Su
pp
ly current (
p
er channel)
VO=15V
No load
25°C 1 2
mA
I
DD
Supply
current
(per
channel)
V
O =
1
.
5
V
,
No
load
Full range 2
mA
IDD(SHDN)
Suppl
y
current in shutdown (per 25°C 0.8 1.5
µA
I
DD(SHDN)
y(
channel) Full range 1.3 2 µ
A
TLV2770 2.59
V
(
ON
)
T urnon voltage level TLV2773 AV = 5 25°C2.47 V
()
TLV2775 2.48
TLV2770 2.41
V
(
OFF
)
T urnoff voltage level TLV2773 AV = 5 25°C2.32 V
()
TLV2775 2.29
†Full range is 0°C to 70°C.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLV277xC
UNIT
PARAMETER
TEST
CONDITIONS
T
A
†
MIN TYP MAX
UNIT
VO(PP) =15V
CL= 100
p
F
25°C5 10.5
SR Slew rate at unity gain
V
O(PP) =
1
.
5
V
,
RL = 10 kΩ
C
L =
100
pF
,Full
range 4.7 6 V/µs
V
Equivalent in
p
ut noise voltage
f = 1 kHz 25°C 17
nV/√Hz
V
n
Equivalent
input
noise
voltage
f = 10 kHz 25°C 12 n
V/√H
z
VN(PP)
Peak to
p
eak equivalent in
p
ut noise voltage
f = 0.1 Hz to 1 Hz
25°C
0.33
µV
V
N(PP)
Peak
-
to
-
peak
equivalent
input
noise
voltage
f = 0.1 Hz to 10 Hz
25°C
0.86 µ
V
InEquivalent input noise current f = 100 Hz 25°C 0.6 fA/√Hz
R 600 Ω
AV = 1 0.005%
THD + N Total harmonic distortion plus noise RL = 600 Ω,
f=1kHz
AV = 10 25°C0.016%
f
=
1
kHz
AV = 100 0.095%
Gain-bandwidth product f = 10 kHz,
CL = 100 pF RL = 600 Ω,25°C 5.1 MHz
t
Settling time
AV = –1,
Step = 2 V, 0.1% 25°C 0.335
µs
t
s
Settling
time
,
RL = 600 Ω,
CL = 100 pF 0.01% 25°C 0.6 µ
s
φmPhase margin at unity gain
RL= 600 Ω
CL= 100
p
F
25°C 46°
Gain margin
R
L =
600
Ω
,
C
L =
100
pF
25°C 12 dB
TLV2770
A 5 R Open
1.2
t(ON) Amplifier turnon time TLV2773
A
V =
5
,
R
L =
O
pen,
Measured to 50%
p
oint
25°C2.4 µs
()
TLV2775
Measured
to
50%
oint
1.9
TLV2770
A 5 R Open
335
t
(
OFF
)
Amplifier turnoff time TLV2773
A
V =
5R
L =
O
pen,
Measured to 50%
p
oint
25°C444 ns
()
TLV2775
Measured
to
50%
oint
345
†Full range is 0°C to 70°C.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 2.7 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLV277xI TLV277xAI
UNIT
PARAMETER
TEST
CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
TLV2770/1/2
25°C 0.44 2.5 0.44 1.6
VIO
Input offset
TLV2770/1/2
VIC = 0, VO = 0,
RS50 Ω
Full range 0.47 2.7 0.47 1.9
mV
V
IO voltage
TLV2773/4/5
R
S =
50
Ω
VDD =±135V
25°C 0.8 2.7 0.8 2.1
mV
TLV2773/4/5
VDD
=
±1
.
35
V
Full range 0.86 2.9 0.86 2.2
αVIO
Temperature coefficient of input 25°C to
2
2
µV/°C
αVIO offset voltage 125°C
2
2
µ
V/°C
IIO
In
p
ut offset current
V
IC
= 0, V
O
= 0, 25°C 1 60 1 60 p
A
I
IO
Input
offset
current
IC ,O,
RS = 50 ΩFull range 2 125 2 125
pA
IIB
In
p
ut bias current
25°C 2 60 2 60 p
A
I
IB
Input
bias
current
Full range 6 350 6 350
pA
0
–03
0
–03
25°C
0
to 1 4
–
0
.
3
to 1 7
0
to 1 4
–
0
.
3
to 1 7
VICR
Common-mode input volta
g
e CMRR > 70 dB,
25 C
t
o
1
.
4
t
o
1
.
7
t
o
1
.
4
t
o
1
.
7
V
V
ICR
g
ran
g
e
,
R
S
= 50 Ω
0
–03
0
–03
V
range
RS
50
Ω
Full ran
g
e
0
to 1 4
–
0
.
3
to 1 7
0
to 1 4
–
0
.
3
to 1 7
Full
range
t
o
1
.
4
t
o
1
.
7
t
o
1
.
4
t
o
1
.
7
IOH = 0 675 mA
25°C 2.6 2.6
VOH
High level out
p
ut voltage
I
OH = –
0
.
675
mA
Full range 2.5 2.5
V
V
OH
High
-
level
output
voltage
IOH =22mA
25°C 2.4 2.4
V
I
OH = –
2
.
2
mA
Full range 2.1 2.1
V
IC
= 1.35 V, 25°C 0.1 0.1
VOL
Low level out
p
ut voltage
IC ,
IOL = 0.675 mA Full range 0.2 0.2
V
V
OL
Low
-
level
output
voltage
V
IC
= 1.35 V, 25°C 0.21 0.21
V
IC ,
IOL = 2.2 mA Full range 0.6 0.6
AVD
Lar
g
e-si
g
nal differential volta
g
eVIC = 1.35 V,
RL10 kΩ
25°C 20 380 20 380
V/mV
A
VD
gg g
amplification
R
L =
10
kΩ
,
VO = 0.6 V to 2.1 V Full range 13 13
V/mV
ri(d) Differential input resistance 25°C 1012 1012 Ω
ci(c) Common-mode input
capacitance f = 10 kHz, 25°C 8 8 pF
zoClosed-loop output impedance f = 100 kHz,
AV = 10 25°C 25 25 Ω
CMRR
Common mode rejection ratio
VIC = 0 to 1.5 V,
VO15V
25°C 70 84 70 84
dB
CMRR
Common
-
mode
rejection
ratio
V
O =
1
.
5
V
,
RS = 50 ΩFull range 70 82 70 82
dB
kSVR
Suppl
y
volta
g
e rejection ratio VDD = 2.7 V to 5 V,
VIC VDD/2
25°C 70 89 70 89
dB
k
SVR
ygj
(∆VDD /∆VIO)
V
IC =
V
DD
/2
,
No load Full range 70 84 70 84
dB
IDD
Su
pp
ly current (
p
er channel)
VO= 1 5 V No load
25°C 1 2 1 2
mA
I
DD
Supply
current
(per
channel)
V
O =
1
.
5
V
,
No
load
Full range 2 2
mA
IDD(SHDN)
Supply current in shutdown (per 25°C 0.8 1.5 0.8 1.5
µA
I
DD(SHDN)
y(
channel) Full range 1.3 2 1.3 2 µ
A
†Full range is – 40°C to 125°C.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 2.7 V (unless otherwise noted)
(continued)
PARAMETER
TEST
TA†
TLV277xI TLV277xAI
UNIT
PARAMETER
CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
TLV2770 1.47 1.47
V(ON) T urnon voltage level TLV2773 AV = 5 25°C1.43 1.43 V
()
TLV2775 1.40 1.4
TLV2770 1.27 1.27
V
(
OFF
)
T urnoff voltage level TLV2773 AV = 5 25°C1.21 1.21 V
()
TLV2775 1.20 1.2
†Full range is – 40°C to 125°C.
operating characteristics at specified free-air temperature, VDD = 2.7 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLV277xI TLV277xAI
UNIT
PARAMETER
TEST
CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VO(PP) =08V
CL= 100
p
F
25°C5 9 5 9
SR Slew rate at unity gain
V
O(PP) =
0
.
8
V
,
RL = 10 kΩ
C
L =
100
pF
,Full
range 4.7 6 4.7 6 V/µs
V
Equivalent input noise f = 1 kHz 25°C 21 21
nV/√Hz
V
n
q
voltage f = 10 kHz 25°C 17 17 n
V/√H
z
VN(PP)
Peak-to-peak
equivalent in
p
ut noise
f = 0.1 Hz to 1 Hz 25°C 0.33 0.33 µV
V
N(PP) equ
i
va
l
en
t
i
npu
t
no
i
se
voltage f = 0.1 Hz to 10 Hz 25°C 0.86 0.86 µV
InEquivalent input noise
current f = 100 Hz 25°C 0.6 0.6 fA/√Hz
Ttlh i
R 600 Ω
AV = 1 0.0085% 0.0085%
THD + N Total harmonic
distortion
p
lus noise
RL = 600 Ω,
f=1kHz
AV = 10 25°C0.025% 0.025%
distortion
lus
noise
f
=
1
kHz
AV = 100 0.12% 0.12%
Gain-bandwidth
product f = 10 kHz,
CL = 100 pF RL = 600 Ω,25°C 4.8 4.8 MHz
t
Settling time
AV = –1,
Step = 0.85 V to
185V
0.1% 25°C 0.186 0.186
µs
t
s
Settling
time
1
.
85
V
,
RL = 600 Ω,
CL = 100 pF 0.01% 25°C 3.92 3.92
µ
s
φmPhase margin at unity
gain R
L
= 600 Ω, C
L
= 100 pF 25°C 46°46°
Gain margin
L,
L
25°C 12 12 dB
†Full range is –40°C to 125°C.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
TEST
TA†
TLV277xI TLV277xAI
UNIT
PARAMETER
CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
TLV2770/1/2
VIC
=
0,
25°C 0.36 2.5 0.36 1.6
VIO
In
p
ut offset voltage
TLV2770/1/2
VIC
=
0
,
VO = 0, Full range 0.4 2.7 0.4 1.9
mV
V
IO
Input
offset
voltage
TLV2773/4/5
O
RS = 50 Ω,25°C 0.7 2.5 0.7 2.1
mV
TLV2773/4/5
VDD = ±2.5 V Full range 0.78 2.7 0.78 2.2
αVIO
Temperature coefficient of input 25°C to
2
2
µV/°C
αVIO offset voltage
VIC =0
125°C
2
2
µ
V/°C
IIO
In
p
ut offset current
VIC
=
0
,
V
O
= 0, 25°C 1 60 1 60 p
A
I
IO
Input
offset
current
O,
RS = 50 Ω,Full range 2 125 2 125
pA
IIB
In
p
ut bias current
VDD = ±2.5 V 25°C 2 60 2 60 p
A
I
IB
Input
bias
current
Full range 6 350 6 350
pA
0
–03
0
–03
25°C
0
to 3 7
–
0
.
3
to 3 8
0
to 3 7
–
0
.
3
to 3 8
VICR
Common-mode input volta
g
e CMRR > 60 dB,
25 C
t
o
3
.
7
t
o
3
.
8
t
o
3
.
7
t
o
3
.
8
V
V
ICR
g
ran
g
e
,
R
S
= 50 Ω
0
–03
0
–03
V
range
RS
50
Ω
Full ran
g
e
0
to 3 7
–
0
.
3
to 3 8
0
to 3 7
–
0
.
3
to 3 8
Full
range
t
o
3
.
7
t
o
3
.
8
t
o
3
.
7
t
o
3
.
8
IOH =13mA
25°C 4.9 4.9
VOH
High level out
p
ut voltage
I
OH = –
1
.
3
mA
Full range 4.8 4.8
V
V
OH
High
-
level
output
voltage
IOH =42mA
25°C 4.7 4.7
V
I
OH = –
4
.
2
mA
Full range 4.4 4.4
V
IC
= 2.5 V, 25°C 0.1 0.1
VOL
Low level out
p
ut voltage
IC ,
IOL = 1.3 mA Full range 0.2 0.2
V
V
OL
Low
-
level
output
voltage
V
IC
= 2.5 V, 25°C 0.21 0.21
V
IC ,
IOL = 4.2 mA Full range 0.6 0.6
AVD
Lar
g
e-si
g
nal differential volta
g
eVIC = 2.5 V,
RL10 kΩ
25°C 20 450 20 450
V/mV
A
VD
gg g
amplification
R
L =
10
kΩ
,
VO = 1 V to 4 V Full range 13 13
V/mV
ri(d) Differential input resistance 25°C 1012 1012 Ω
ci(c) Common-mode input capacitance f = 10 kHz 25°C 8 8 pF
zoClosed-loop output impedance f = 100 kHz,
AV = 10 25°C 20 20 Ω
CMRR
Common mode rejection ratio
VIC = 0 to 3.7 V,
VO37V
25°C 60 96 60 96
dB
CMRR
Common
-
mode
rejection
ratio
V
O =
3
.
7
V
,
RS = 50 ΩFull range 60 93 60 93
dB
kSVR
Suppl
y
volta
g
e rejection ratio VDD = 2.7 V to 5 V,
VIC VDD/2
25°C 70 89 70 89
dB
k
SVR
ygj
(∆VDD /∆VIO)
V
IC =
V
DD
/2
,
No load Full range 70 84 70 84
dB
IDD
Su
pp
ly current (
p
er channel)
VO = 1.5 V, 25°C 1 2 1 2
mA
I
DD
Supply
current
(per
channel)
O
No load Full range 2 2
mA
IDD(SHDN)
Supply current shutdown (per 25°C 0.8 1.5 0.8 1.5
µA
I
DD(SHDN)
y(
channel) Full range 1.3 2 1.3 2 µ
A
†Full range is – 40°C to 125°C.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
(continued)
PARAMETER
TEST
TA†
TLV277xI TLV277xAI
UNIT
PARAMETER
CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
TLV2770 2.59 2.59
V(ON) T urnon voltage level TLV2773 AV = 5 25°C2.47 2.47 V
()
TLV2775 2.48 2.48
TLV2770 2.41 2.41
V
(
OFF
)
T urnoff voltage level TLV2773 AV = 5 25°C2.32 2.32 V
()
TLV2775 2.29 2.29
†Full range is – 40°C to 125°C.
operating characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLV277xI TLV277xAI
UNIT
PARAMETER
TEST
CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VO(PP) =15V
CL= 100
p
F
25°C5 10.5 5 10.5
SR Slew rate at unity gain
V
O(PP) =
1
.
5
V
,
RL = 10 kΩ
C
L =
100
pF
,Full
range 4.7 6 4.7 6 V/µs
V
Equivalent input noise f = 1 kHz 25°C 17 17
nV/√Hz
V
n
q
voltage f = 10 kHz 25°C 12 12 n
V/√H
z
VN(PP)
Peak-to-peak
equivalent in
p
ut
f = 0.1 Hz to 1 Hz 25°C 0.33 0.33 µV
V
N(PP) equ
i
va
l
en
t
i
npu
t
noise voltage f = 0.1 Hz to 10 Hz 25°C 0.86 0.86 µV
InEquivalent input noise
current f = 100 Hz 25°C 0.6 0.6 fA/√Hz
Ttlh i
R 600 Ω
AV = 1 0.005% 0.005%
THD + N Total harmonic
distortion
p
lus noise
RL = 600 Ω,
f=1kHz
AV = 10 25°C0.016% 0.016%
distortion
lus
noise
f
=
1
kHz
AV = 100 0.095% 0.095%
Gain-bandwidth
product f = 10 kHz,
CL = 100 pF RL = 600 Ω,25°C 5.1 5.1 MHz
t
Settling time
AV = –1,
Step = 1.5 V to
35V
0.1% 25°C 0.134 0.134
µs
t
s
Settling
time
3
.
5
V
,
RL = 600 Ω,
CL = 100 pF 0.01% 25°C 1.97 1.97
µ
s
φmPhase margin at unity
gain R
L
= 600 Ω, C
L
= 100 pF 25°C 46°46°
Gain margin
L,
L
25°C 12 12 dB
Amplifier TLV2770 A
V
=
5,
1.2 1.2
t(ON)
Am lifier
turnon
ti
TLV2773
AV
=
5
,
RL = Open,
M d 50% i
25°C2.4 2.4 µs
()
time TLV2775 Measured to 50% point 1.9 1.9
Amplifier TLV2770 A
V
=
5,
335 335
t(OFF)
Am lifier
turnoff
ti
TLV2773
AV
=
5
,
RL = Open,
M d 50% i
25°C444 444 ns
()
time TLV2775 Measured to 50% point 345 345
†Full range is –40°C to 125°C.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 2.7 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T
A
†TLV2772Q
TLV2772M TLV2772AQ
TLV2772AM UNIT
A
MIN TYP MAX MIN TYP MAX
VIO
In
p
ut offset voltage
V V
V
25°C 0.44 2.5 0.44 1.6
mV
V
IO
Input
offset
voltage
V V
V
Full range 0.47 2.7 0.47 1.9
mV
αVIO
Temperature
coefficient of in
p
ut
V V
V
25°C
to
2
2
µV/°C
αVIO coe
ffi
c
i
en
t
o
f
i
npu
t
offset voltage
V
DD = ±1.35
V
,
V
IC
= 0
,
V
O = 0,
t
o
125°C
2
2
µ
V/°C
IIO
In
p
ut offset current
IC 0,
RS = 50 Ω25°C 1 60 1 60 p
A
I
IO
Input
offset
current
Full range 2 125 2 125
pA
IIB
In
p
ut bias current
25°C 2 60 2 60 p
A
I
IB
Input
bias
current
Full range 6 350 6 350
pA
0–0.3 0 –0.3
25°C
0
to
0.3
to
0
to
0.3
to
VICR
Common-mode
CMRR>60dB
RS=50Ω
1.4 1.7 1.4 1.7
V
V
ICR input voltage range
CMRR
>
60
dB
,
R
S =
50
Ω
0–0.3 0 –0.3
V
Full range
0
to
0.3
to
0
to
0.3
to
g
1.4 1.7 1.4 1.7
IOH = 0 675 mA
25°C 2.6 2.6
VOH
Hi
g
h-level output
I
OH = –
0
.
675
mA
Full range 2.45 2.45
V
V
OH
g
voltage
IOH =22mA
25°C 2.4 2.4
V
I
OH = –
2
.
2
mA
Full range 2.1 2.1
VIC = 1 35 V
IOL = 0 675 mA
25°C 0.1 0.1
VOL
Low-level output
V
IC =
1
.
35
V
,
I
OL =
0
.
675
mA
Full range 0.2 0.2
V
V
OL voltage
VIC = 1 35 V
IOL =22mA
25°C 0.21 0.21
V
V
IC =
1
.
35
V
,
I
OL =
2
.
2
mA
Full range 0.6 0.6
AVD
Large-signal
differential voltage
V
IC
= 1.35 V, R
L
= 10 kΩ,
‡
25°C 20 380 20 380
V/mV
A
VD
diff
eren
ti
a
l
vo
lt
age
amplification
IC ,
VO = 0.6 V to 2.1 V
L,
Full range 13 13
V/mV
ri(d) Differential input
resistance 25°C 1012 1012 Ω
ci(c) Common-mode
input capacitance f = 10 kHz, 25°C 8 8 pF
zoClosed-loop
output impedance f = 100 kHz, AV = 10 25°C 25 25 Ω
CMRR
Common-mode V
IC
= V
ICR
(min),
VO
= 1.5
V
, 25°C 60 84 60 84
dB
CMRR
rejection ratio
IC ICR (),
RS = 50 Ω
O,
Full range 60 82 60 82
dB
kSVR
Supply voltage
rejection ratio
V
DD
= 2.7 V to 5 V, V
IC
= V
DD
/2, 25°C 70 89 70 89
dB
k
SVR re
j
ec
ti
on ra
ti
o
(∆VDD /∆VIO)
DD ,
No load
IC DD ,
Full range 70 84 70 84
dB
IDD
Supply current
VO=15V
No load
25°C 1 2 1 2
mA
I
DD
y
(per channel)
V
O =
1
.
5
V
,
No
load
Full range 2 2
mA
†Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.
‡Referenced to 1.35 V
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 2.7 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T
A
†TLV2772Q
TLV2772M TLV2772AQ
TLV2772AM UNIT
A
MIN TYP MAX MIN TYP MAX
VO(PP) =08V
CL= 100
p
F
25°C5 9 5 9
SR Slew rate at unity gain
V
O(PP) =
0
.
8
V
,
RL = 10 kΩ
C
L =
100
pF
,Full
range 4.7 6 4.7 6 V/µs
V
Equivalent input f = 1 kHz 25°C 21 21
nV/√Hz
V
n
q
noise voltage f = 10 kHz 25°C 17 17 n
V/√H
z
VN(PP)
Peak-to-peak
equivalent in
p
ut
f = 0.1 Hz to 1 Hz 25°C 0.33 0.33 µV
V
N(PP) equ
i
va
l
en
t
i
npu
t
noise voltage f = 0.1 Hz to 10 Hz 25°C 0.86 0.86 µV
InEquivalent input
noise current f = 100 Hz 25°C 0.6 0.6 fA/√Hz
Ttlh i
R 600 Ω
AV = 1 0.0085% 0.0085%
THD + N Total harmonic
distortion
p
lus noise
RL = 600 Ω,
f=1kHz
AV = 10 25°C0.025% 0.025%
distortion
lus
noise
f
=
1
kHz
AV = 100 0.12% 0.12%
Gain-bandwidth
product f = 10 kHz,
CL = 100 pF RL = 600 Ω,25°C 4.8 4.8 MHz
t
Settling time
AV = –1,
Step = 0.85 V to
185V
0.1% 25°C 0.186 0.186
µs
t
s
Settling
time
1
.
85
V
,
RL = 600 Ω,
CL = 100 pF 0.01% 25°C 3.92 3.92
µ
s
φmPhase margin at
unity gain R
L
= 600 Ω, C
L
= 100 pF 25°C 46°46°
Gain margin
L,
L
25°C 12 12 dB
†Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T
A
†TLV2772Q
TLV2772M TLV2772AQ
TLV2772AM UNIT
A
MIN TYP MAX MIN TYP MAX
VIO
In
p
ut offset voltage
V V
V
25°C 0.36 2.5 0.36 1.6
mV
V
IO
Input
offset
voltage
V V
V
Full range 0.4 2.7 0.4 1.9
mV
αVIO
Temperature
coefficient of in
p
ut
V V
V
25°C
to
2
2
µV/°C
αVIO coe
ffi
c
i
en
t
o
f
i
npu
t
offset voltage
V
DD = ±2.5
V
,
VIC 0
V
O = 0,
RS50 Ω
t
o
125°C
2
2
µ
V/°C
IIO
In
p
ut offset current
V
IC =
0
,
R
S =
50
Ω
25°C 1 60 1 60 p
A
I
IO
Input
offset
current
Full range 2 125 2 125
pA
IIB
In
p
ut bias current
25°C 2 60 2 60 p
A
I
IB
Input
bias
current
Full range 6 350 6 350
pA
0–0.3 0 –0.3
25°C
0
to
0.3
to
0
to
0.3
to
VICR
Common-mode
CMRR>60dB
RS=50Ω
3.7 3.8 3.7 3.8
V
V
ICR input voltage range
CMRR
>
60
dB
,
R
S =
50
Ω
0–0.3 0 –0.3
V
Full range
0
to
0.3
to
0
to
0.3
to
g
3.7 3.8 3.7 3.8
IOH =13mA
25°C 4.9 4.9
VOH
Hi
g
h-level output
I
OH = –
1
.
3
mA
Full range 4.8 4.8
V
V
OH
g
voltage
IOH =42mA
25°C 4.7 4.7
V
I
OH = –
4
.
2
mA
Full range 4.4 4.4
VIC =25V
IOL =13mA
25°C 0.1 0.1
VOL
Low-level output
V
IC =
2
.
5
V
,
I
OL =
1
.
3
mA
Full range 0.2 0.2
V
V
OL voltage
VIC =25V
IOL =42mA
25°C 0.21 0.21
V
V
IC =
2
.
5
V
,
I
OL =
4
.
2
mA
Full range 0.6 0.6
AVD
Large-signal
differential voltage
V
IC
= 2.5 V, R
L
= 10 kΩ,
‡
25°C 20 450 20 450
V/mV
A
VD
diff
eren
ti
a
l
vo
lt
age
amplification
IC ,
VO = 1 V to 4 V
L,
Full range 13 13
V/mV
ri(d) Differential input
resistance 25°C 1012 1012 Ω
ci(c) Common-mode
input capacitance f = 10 kHz, 25°C 8 8 pF
zoClosed-loop
output impedance f = 100 kHz, AV = 10 25°C 20 20 Ω
CMRR
Common-mode V
IC
= V
ICR
(min),
VO
= 3.7
V
, 25°C 60 96 60 96
dB
CMRR
rejection ratio
IC ICR (),
RS = 50 Ω
O,
Full range 60 93 60 93
dB
kSVR
Supply voltage
rejection ratio
V
DD
= 2.7 V to 5 V, V
IC
= V
DD
/2, 25°C 70 89 70 89
dB
k
SVR re
j
ec
ti
on ra
ti
o
(∆VDD /∆VIO)
DD ,
No load
IC DD ,
Full range 70 84 70 84
dB
IDD
Supply current
VO=15V
No load
25°C 1 2 1 2
mA
I
DD
y
(per channel)
V
O =
1
.
5
V
,
No
load
Full range 2 2
mA
†Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.
‡Referenced to 2.5 V
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T
A
†TLV2772Q
TLV2772M TLV2772AQ
TLV2772AM UNIT
A
MIN TYP MAX MIN TYP MAX
VO(PP) =15V
CL= 100
p
F
25°C5 10.5 5 10.5
SR Slew rate at unity gain
V
O(PP) =
1
.
5
V
,
RL = 10 kΩ
C
L =
100
pF
,Full
range 4.7 6 4.7 6 V/µs
V
Equivalent input f = 1 kHz 25°C 17 17
nV/√Hz
V
n
q
noise voltage f = 10 kHz 25°C 12 12 n
V/√H
z
VN(PP)
Peak-to-peak
equivalent in
p
ut
f = 0.1 Hz to 1 Hz 25°C 0.33 0.33 µV
V
N(PP) equ
i
va
l
en
t
i
npu
t
noise voltage f = 0.1 Hz to 10 Hz 25°C 0.86 0.86 µV
InEquivalent input
noise current f = 100 Hz 25°C 0.6 0.6 fA/√Hz
Ttlh i
R 600 Ω
AV = 1 0.005% 0.005%
THD + N Total harmonic
distortion
p
lus noise
RL = 600 Ω,
f=1kHz
AV = 10 25°C0.016% 0.016%
distortion
lus
noise
f
=
1
kHz
AV = 100 0.095% 0.095%
Gain-bandwidth
product f = 10 kHz,
CL = 100 pF RL = 600 Ω,25°C 5.1 5.1 MHz
t
Settling time
AV = –1,
Step = 1.5 V to
35V
0.1% 25°C 0.134 0.134
µs
t
s
Settling
time
3
.
5
V
,
RL = 600 Ω,
CL = 100 pF 0.01% 25°C 1.97 1.97
µ
s
φmPhase margin at unity
gain R
L
= 600 Ω, C
L
= 100 pF 25°C 46°46°
Gain margin
L,
L
25°C 12 12 dB
†Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
In
p
ut offset voltage
Distribution
vs Common mode in
p
ut voltage
1,2
34
V
IO
Input
offset
voltage
vs
Common
-
mode
input
voltage
Distribution
3
,
4
5,6
IIB/IIO Input bias and input offset currents vs Free-air temperature 7
VOH High-level output voltage vs High-level output current 8,9
VOL Low-level output voltage vs Low-level output current 10,11
VO(PP) Maximum peak-to-peak output voltage vs Frequency 12,13
IOS Short-circuit output current vs Supply voltage
vs Free-air temperature 14
15
VOOutput voltage vs Differential input voltage 16
AVD Large-signal differential voltage amplification and phase margin vs Frequency 17,18
AVD Differential voltage amplification vs Load resistance
vs Free-air temperature 19
20,21
zoOutput impedance vs Frequency 22,23
CMRR Common-mode rejection ratio vs Frequency
vs Free-air temperature 24
25
kSVR Supply-voltage rejection ratio vs Frequency 26,27
IDD Supply current (per channel) vs Supply voltage 28
SR
Slew rate
vs Load capacitance 29
SR
Slew
rate
vs Free-air temperature 30
VOVoltage-follower small-signal pulse response 31,32
VOVoltage-follower large-signal pulse response 33,34
VOInverting small-signal pulse response 35,36
VOInverting large-signal pulse response 37,38
VnEquivalent input noise voltage vs Frequency 39,40
Noise voltage (referred to input) Over a 10-second period 41
THD + N Total harmonic distortion plus noise vs Frequency 42,43
Gain-bandwidth product vs Supply voltage 44
B1Unity-gain bandwidth vs Load capacitance 45
φmPhase margin vs Load capacitance 46
Gain margin vs Load capacitance 47
Amplifier with shutdown pulse turnon/off characteristics 48 – 50
Supply current with shutdown pulse turnon/off characteristics 51 – 53
Shutdown supply current vs Free-air temperature 54
Shutdown forward/reverse isolation vs Frequency 55, 56
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 1
–2.5
30
20
10
0–2–1.5 –1 0 0.5
VIO – Input Offset Voltage – mV
–0.5
35
Percentage of Amplifiers – %
25
15
5
1
40 VDD = 2.7 V
RL = 10 kΩ
TA = 25°C
DISTRIBUTION OF TLV2772
INPUT OFFSET VOLTAGE
1.5 2.52
Figure 2
–2.5
30
20
10
0–2–1.5 –1 0 0.5
VIO – Input Offset Voltage – mV
–0.5
35
Percentage of Amplifiers – %
25
15
5
1
40 VDD =5 V
RL = 10 kΩ
TA = 25°C
DISTRIBUTION OF TLV2772
INPUT OFFSET VOLTAGE
1.5 2.52
Figure 3
VDD = 2.7 V
TA = 25°C
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
2
1
0
–1
–2
1.5
0.5
–0.5
–1.5
–1–0.5 0 0.5 2
VIC – Common-Mode Input Voltage – V
1.51 2.5 3
VIO – Input Offset Voltage – mV
Figure 4
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
1
0
–1
–2
–1 0 0.5
VIC – Common-Mode Input Voltage – V
–0.5
1.5
0.5
–0.5
–1.5
1
2
1.5 2.52 3 3.5 4.54
VDD = 5 V
TA = 25°C
VIO – Input Offset Voltage – mV
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 5
αVIO – Temperature Coefficient – µV/°C
–6
30
20
10
0–303 9126
35
Percentage of Amplifiers – %
25
15
5
VDD = 2.7 V
TA = 25°C to 125°C
DISTRIBUTION OF TLV2772
INPUT OFFSET VOLTAGE
Figure 6
–6
30
20
10
0–303 912
αVIO – Temperature Coefficient – µV/°C
6
35
Percentage of Amplifiers – %
25
15
5
VDD =5 V
TA = 25°C to 125°C
DISTRIBUTION OF TLV2772
INPUT OFFSET VOLTAGE
Figure 7
VDD = 5 V
VIC = 0
VO = 0
RS = 50 Ω
INPUT BIAS AND OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
0.20
0.10
0
0.15
0.05
–75 –50 –25 0 75
TA – Free-Air Temperature – °C
5025 100 125
IIB and I IO – Input Bias and Input Offset Currents – nA
IIB
IIO
Figure 8
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
3
2
1
0
2.5
1.5
0.5
0 5 10 15
IOH – High-Level Output Current – mA 2520
VOH – High-Level Output Voltage – V
VDD = 2.7 V
TA = 125°C
TA = –40°C
TA = 25°C
TA = 85°C
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 9
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
3
2
1
001015
IOH – High-Level Output Current – mA
5
3.5
2.5
1.5
0.5
20
4
25 3530 40 45 5550
VDD = 5 V
TA = 25°C
VOH – High-Level Output Voltage – V
4.5
5
TA = –40°C
TA = 85°C
TA = 25°C
TA = 125°C
Figure 10
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
3
2
1
0
2.5
1.5
0.5
0 5 10 15
IOL – Low-Level Output Current – mA 3020
VOL – Low-Level Output Voltage – V
VDD = 2.7 V
TA = 125°C
25
TA = 85°C
TA = 25°C
TA = –40°C
Figure 11
2
1
0010
IOL – Low-Level Output Current – mA
2.5
1.5
0.5
20
3
30 40 50
VDD = 5 V
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
TA = 125°C
TA = 85°C
TA = –40°C
TA = 25°C
VOL – Low-Level Output Voltage – V
Figure 12
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
3
1
01000
f – Frequency – kHz
5
10000
100
4
RL = 10 kΩ
VO(PP) – Maximum Peak-to-Peak Output Voltage – V
2
VDD = 5 V
1% THD
VDD = 2.7 V
2% THD
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
22 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 13
THD = 5%
RL = 600 Ω
TA = 25°C
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
3
2
1
0
2.5
1.5
0.5
100 f – Frequency – kHz
1000 10000
VDD = 5 V
VDD = 2.7 V
5
4
4.5
3.5
– Maximum Peak-to-Peak Output Voltage – V
VO(PP)
Figure 14
SHORT-CIRCUIT OUTPUT CURRENT
vs
SUPPLY VOLTAGE
30
0
–30
–60245
VDD – Supply Voltage – V
3
45
15
–15
–45
6
60
7
VO = VDD /2
VIC = VDD /2
TA = 25°C
IOS – Short-Circuit Output Current – mA
VID = –100 mV
VID = 100 mV
Figure 15
VDD = 5 V
VO = 2.5 V
SHORT-CIRCUIT OUTPUT CURRENT
vs
FREE-AIR TEMPERATURE
60
20
–20
–60
40
0
–40
–75 –50 –25 0 75
TA – Free-Air Temperature – °C
5025 100 125
IOS – Short-Circuit Output Current – mA
VID = –100 mV
VID = 100 mV
Figure 16
RL = 600 Ω
TA = 25°C
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
4
2
0
5
3
1
–1000 –750 –500 –250 500
VID – Differential Input Voltage – µV
2500 750 1000
VO– Output Voltage – V
VDD = 2.7 V
VDD = 5 V
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
100
60
20
–20
80
40
0
100 f – Frequency – Hz
10k 10M
AVD
Phase
LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION
AND PHASE MARGIN
vs
FREQUENCY
– Large-Signal Differential Amplification – dBAVD
m
φ– Phase Margin – degrees
300
180
60
–60
240
120
0
1k 100k 1M
–40 –90
VDD = 2.7 V
RL = 600 Ω
CL = 600 pF
TA = 25°C
Figure 17
300
180
60
–60
240
120
0
–90
100
60
20
–20
80
40
0
–40
100 f – Frequency – Hz
10k 10M
AVD
Phase
VDD = 5 V
RL = 600 Ω
CL = 600 pF
TA = 25°C
LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION
AND PHASE MARGIN
vs
FREQUENCY
– Large-Signal Differential Amplification – dBAVD
m
φ– Phase Margin – degrees
1k 100k 1M
Figure 18
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
24 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Fi
g
ure 19
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
200
100
010
RL – Load Resistance – kΩ
250
150
50
1 100 10000.1
TA = 25°C
– Differential Voltage Amplification – V/mVAVD
VDD = 2.7 V
VDD = 5 V
Figure 20
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
1000
10
0.1
100
1
– Differential Voltage Amplification – V/mVAVD
TA – Free-Air Temperature – °C
–75 –50 –25 0 755025 100 125
VDD = 2.7 V
VIC = 1.35 V
VO = 0.6 V to 2.1 V
RL = 1 MΩ
RL = 600 Ω
RL = 10 kΩ
Figure 21
–50
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
1000
10
0.1
100
1
– Differential Voltage Amplification – V/mVAVD
TA – Free-Air Temperature – °C
VDD = 5 V
VIC = 2.5 V
VO = 1 V to 4 V
RL = 1 MΩ
RL = 600 Ω
–75 –25 0 755025 100 125
RL = 10 kΩ
Figure 22
OUTPUT IMPEDANCE
vs
FREQUENCY
100
1
0.01
10
0.10
100 1k 10k 100k
f – Frequency – Hz 1M
ZO– Output Impedance –
AV = 100
AV = 10
AV = 1
VDD = 2.7 V
TA = 25°C
Ω
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
25
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 23
OUTPUT IMPEDANCE
vs
FREQUENCY
100
1
0.01
10
0.1
f – Frequency – Hz
100 1k 10k 100k 1M
VDD = ±2.5 V
TA = 25°C
Av = 100
– Output Impedance –ZoΩ
Av = 10
Av = 1
Figure 24
VIC = 1.35 V
and 2.5 V
TA = 25°C
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
90
80
60
40
70
50
10 100 1k
f – Frequency – Hz
10k 100k 10M
VDD = 5 V
VDD = 2.7 V
CMRR – Common-Mode Rejection Ratio – dB
1M
Figure 25
–20–40 0 20 806040 100 120
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
110
100
90
80
105
95
85
TA – Free-Air Temperature – °C
CMRR – Common-Mode Rejection Ratio – dB
120
115
VDD = 5 V
VDD = 2.7 V
140
Figure 26
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
120
60
0
10 100 1k 10k
f – Frequency – Hz 10M
kSVR– Supply-Voltage Rejection Ratio – dB
kSVR–
VDD = 2.7 V
TA = 25°C
100k 1M
kSVR+
100
40
80
20
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
26 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 27
SUPPLY VOLTAGE REJECTION RATIO
vs
FREQUENCY
120
80
40
0
100
60
20
10 100 1 k 10 k 10 M
f – Frequency – Hz 1 M100 k
kSVR – Supply Voltage Rejection Ratio – dB
kSVR+
kSVR–
VDD = 5 V
TA = 25°C
Figure 28
SUPPLY CURRENT (PER CHANNEL)
vs
SUPPLY VOLTAGE
1.2
0.8
0.4
0
1
0.6
0.2
2.5 3 3.5 4
VDD – Supply Voltage – V 74.5
IDD – Supply Current (Per Channel) – mA
TA = 0°C
1.6
1.4
5 5.5 6 6.5
TA = 125°C
TA = 85°C
TA = 25°C
TA = –40°C
Figure 29
SLEW RATE
vs
LOAD CAPACITANCE
1k
CL – Load Capacitance – pF
100 10k 100k10
VDD = 5 V
AV = –1
TA = 25°C
SR+
12
8
4
0
10
6
2
16
14
SR – Slew Rate – V/µs
SR–
Figure 30
–50–75 –25 0 755025 100 125
SLEW RATE
vs
FREE-AIR TEMPERATURE
14
12
10
8
13
11
9
TA – Free-Air Temperature – °C
VDD = 2.7 V
RL = 10 kΩ
CL = 100 pF
AV = 1
SR – Slew Rate – µs
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
27
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 31
t – Time – µs
VOLTAGE-FOLLOWER
SMALL-SIGNAL PULSE RESPONSE
VDD = 2.7 V
RL = 600 Ω
CL = 100 pF
AV = 1
TA = 25°C
40
0
20
–20
VO– Output Voltage – mV
80
60
0 1.510.5 2 2.5 3.53 4 4.5 5
100
–40
–60
Figure 32
t – Time – µs
VDD = 5 V
RL = 600 Ω
CL = 100 pF
AV = 1
TA = 25°C
VOLTAGE-FOLLOWER
SMALL-SIGNAL PULSE RESPONSE
40
0
20
–20
VO– Output Voltage – mV
80
60
0 1.510.5 2 2.5 3.53 4 4.5 5
100
–40
–60
Figure 33
t – Time – µs
VOLTAGE-FOLLOWER
LARGE-SIGNAL PULSE RESPONSE
VDD = 2.7 V
RL = 600 Ω
CL = 100 pF
AV = 1
TA = 25°C
1.5
0.5
1
0
VO– Output Voltage – V
2.5
2
0 1.510.5 2 2.5 3.53 4 4.5 5
3
–0.5
–1
Figure 34
t – Time – µs
VDD = 5 V
RL = 600 Ω
CL = 100 pF
AV = 1
TA = 25°C
VOLTAGE-FOLLOWER
LARGE-SIGNAL PULSE RESPONSE
3
1
2
0
VO– Output Voltage – V
5
4
0 1.510.5 2 2.5 3.53 4 4.5 5
6
–1
–2
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
28 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 35
t – Time – µs
VDD = 2.7 V
RL = 600 Ω
CL = 100 pF
AV = –1
TA = 25°C
INVERTING SMALL-SIGNAL
PULSE RESPONSE
40
0
20
–20
VO– Output Voltage – mV
80
60
0 1.510.5 2 2.5 3.53 4 4.5 5
100
–40
–60
Figure 36
t – Time – µs
VDD = 5 V
RL = 600 Ω
CL = 100 pF
AV = –1
TA = 25°C
INVERTING SMALL-SIGNAL
PULSE RESPONSE
40
0
20
–20
VO– Output Voltage – mV
80
60
0 1.510.5 2 2.5 3.53 4 4.5 5
100
–40
–60
Figure 37
t – Time – µs
VDD = 2.7 V
RL = 600 Ω
CL = 100 pF
AV = –1
TA = 25°C
INVERTING LARGE-SIGNAL
PULSE RESPONSE
1.5
0.5
1
0
VO– Output Voltage – V
2.5
2
0 1.510.5 2 2.5 3.53 4 4.5 5
3
–0.5
–1
Figure 38
t – Time – µs
VDD = 5 V
RL = 600 Ω
CL = 100 pF
AV = –1
TA = 25°C
INVERTING LARGE-SIGNAL
PULSE RESPONSE
2.5
1.5
2
1
VO– Output Voltage – V
3.5
3
0 1.510.5 2 2.5 3.53 4 4.5 5
4
0.5
1
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
29
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 39
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
120
80
40
0100 10k
f – Frequency – Hz
140
100
60
20
1k
160
10
VDD = 2.7 V
RS = 20 Ω
TA = 25°C
– Input Noise Voltage –VnnV/ Hz
Figure 40
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
100
f – Frequency – Hz
1k 10k10
VDD = 5 V
RS = 20 Ω
TA = 25°C
120
80
40
0
100
60
20
140
– Input Noise Voltage –nV Hz
Vn
t – Time – s
VDD = 5 V
f = 0.1 Hz to 10 Hz
TA = 25°C
NOISE VOLTAGE
OVER A 10 SECOND PERIOD
012345678910
Noise Voltage – nV
300
100
–100
–300
200
GND
–200
Figure 41
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
30 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 42
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
10
0.1
0.001
1
0.01
f – Frequency – Hz
10 100 1k 10k 100k
VDD = 2.7 V
RL = 600 Ω
TA = 25°C
THD+N – Total Harmonic Distortion Plus Noise – %
Av = 100
Av = 10
Av = 1
Figure 43
10
0.1
0.001
1
0.01
f – Frequency – Hz
10 100 1k 10k 100k
VDD = 5 V
RL = 600 Ω
TA = 25°C
THD+N – Total Harmonic Distortion Plus Noise – %
Av = 100
Av = 10
Av = 1
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
Figure 44
GAIN-BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
5.2
4.8
4.4
4
5
4.6
4.2
2 2.5 3 3.5 5
VDD – Supply Voltage – V
4.54 5.5 6
Gain-Bandwidth Product – MHz
RL = 600 Ω
CL = 100 pF
f = 10 kHz
TA = 25°C
Figure 45
UNITY-GAIN BANDWIDTH
vs
LOAD CAPACITANCE
4
2
01k
CL – Load Capacitance – pF
5
3
1
100 10k 100k10
Unity-Gain Bandwidth – MHz
Rnull = 0
Rnull = 20
Rnull = 50
Rnull = 100
VDD = 5 V
RL = 600 Ω
TA = 25°C
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
31
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 46
60
40
20
0
50
30
10
10 CL – Load Capacitance – pF
1k
VDD = 5 V
RL = 600 Ω
TA = 25°C
m
φ– Phase Margin – degrees
100 10k 100K
PHASE MARGIN
vs
LOAD CAPACITANCE
90
70
80
Rnull = 0
Rnull = 20 Ω
Rnull = 50 Ω
Rnull = 100 Ω
Figure 47
15
25
35
40
20
30
10 CL – Load Capacitance – pF
1k
VDD = 5 V
RL = 600 Ω
TA = 25°C
Gain Margin – dB
100 10k 100K
GAIN MARGIN
vs
LOAD CAPACITANCE
0
10
5
Rnull = 0
Rnull = 20 Ω
Rnull = 50 Ω
Rnull = 100 Ω
Figure 48
VDD = 5 V
AV = 5
TA = 25°C
TLV2770
AMPLIFIER WITH SHUTDOWN PULSE
TURNON/OFF CHARACTERISTICS
6
0
–4
–8
–12
2
–2
–6
–10
–4–202 8
t – Time – µs
641014
Shutdown Signal – V
12
– Output Voltage – V
VO
8
6
5
4
3
2
1
0
–1
47
SHDN = VDD
SHDN = GND
VO
Figure 49
TLV2773
AMPLIFIER WITH SHUTDOWN PULSE
TURNON/OFF CHARACTERISTICS
8
2
–2
–6
–10
4
0
–4
–8
–2.5 0 2.5 7.5
t – Time – µs
510 15
Shutdown Signal – V
12.5
– Output Voltage – V
VO
8
6
5
4
3
2
1
0
–1
67
SHDN = VDD
VO
Channel 1
VDD = 5 V
AV = 5
TA = 25°C
Channel 1 Switched
Channel 2 SHDN MODE
SHDN = GND
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
32 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 50
TLV2775 – CHANNEL 1
AMPLIFIER WITH SHUTDOWN PULSE
TURNON/OFF CHARACTERISTICS
8
2
–2
–6
–10
4
0
–4
–8
–2.5 0 2.5 7.5
t – Time – µs
510 15
Shutdown Signal – V
12.5
– Output Voltage – V
VO
8
6
5
4
3
2
1
0
–1
67
SHDN = VDD
VO
Channel 1
VDD = 5 V
AV = 5
TA = 25°C
Channel 1/2 Switched
Channel 3/4 SHDN MODE
SHDN = GND
TLV2770
SUPPLY CURRENT WITH SHUTDOWN PULSE
TURNON/OFF CHARACTERISTICS
6
0
–4
–8
–12
2
–2
–6
–10
–4–20 4
t – Time – µs
26 14
Shutdown Signal – V
8
24
18
15
12
9
6
3
0
–3
421
Figure 51
IDD – Supply Current – mA
10 12
VDD = 5 V
AV = 5
TA = 25°C
SHDN = GND
SHDN = VDD
IDD
Figure 52
TLV2773
SUPPLY CURRENT WITH SHUTDOWN PULSE
TURNON/OFF CHARACTERISTICS
6
–3
–9
–18
0
–6
–12
–15
–5–2.5 0 5
t – Time – µs
2.5 7.5 15
Shutdown Signal – V
10
70
50
40
30
20
10
0
–3
360
IDD – Supply Current – mA
12.5
VDD = 5 V
AV = 5
TA = 25°C
Channel 1 Switched
Channel 2 SHDN MODE
SHDN = GND
SHDN = VDD
IDD
Figure 53
TLV2775
SUPPLY CURRENT WITH SHUTDOWN PULSE
TURNON/OFF CHARACTERISTICS
6
–3
–9
–18
0
–6
–12
–15
–5–2.5 0 5
t – Time – µs
2.5 7.5 15
Shutdown Signal – V
10
70
50
40
30
20
10
0
–3
360
IDD – Supply Current – mA
12.5
VDD = 5 V
AV = 5
TA = 25°C
Channel 1/2 Switched
Channel 3/4 SHDN MODE
SHDN = GND
SHDN = VDD
IDD
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
33
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 54
7
4
2
0
5
3
1
–75 –50 –25 25
TA – Free-Air Temperature – °C
0 50 125
75
6
100
AV = 5
RL = OPEN
SHDN = GND
VDD 5 V
SHUTDOWN SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
VDD 2.7 V
DD
I Shutdown Supply Current – –Aµ
Figure 55
TLV2770
SHUTDOWN FORWARD ISOLATION
vs
FREQUENCY
140
20
–20
40
0
f – Frequency – Hz
10 102103104106
Shutdown Forward Isolation – dB
SHDN MODE
AV = 1
VDD = 2.7 V
RL = 10 kΩ
CL = 20 pF
TA = 25°C
VI(PP) = 2.7 V
105
100
120
80
60
VI(PP) = 0.1 V
Figure 56
TLV2770
SHUTDOWN REVERSE ISOLATION
vs
FREQUENCY
140
20
–20
40
0
f – Frequency – Hz
10 102103104106
Shutdown Reverse Isolation – dB
SHDN MODE
AV = 1
VDD = 2.7 V
RL = 10 kΩ
CL = 20 pF
TA = 25°C
VI(PP) = 2.7 V
105
100
120
80
60 VI(PP) = 0.1 V
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
34 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
_
+
Rnull
RLCL
Figure 57
driving a capacitive load
When the amplifier is configured in this manner, capacitive loading directly on the output will decrease the
device’s phase margin leading to high frequency ringing or oscillations. Therefore, for capacitive loads of greater
than 10 pF, it is recommended that a resistor be placed in series (RNULL) with the output of the amplifier, as
shown in Figure 58. A minimum value of 20 Ω should work well for most applications.
CLOAD
RF
Input Output
RGRNULL
_
+
Figure 58. Driving a Capacitive Load
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
35
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
offset voltage
The output offset voltage, (VOO) is the sum of the input offset voltage (VIO) and both input bias currents (IIB) times
the corresponding gains. The following schematic and formula can be used to calculate the output offset
voltage:
VOO
+
VIO
ǒ
1
)ǒ
RF
RG
ǓǓ"
IIB
)
RS
ǒ
1
)ǒ
RF
RG
ǓǓ"
IIB–RF
+
–
VI+
RG
RS
RF
IIB–
VO
IIB+
Figure 59. Output Offset Voltage Model
general configurations
When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often
required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier
(see Figure 60).
VIVO
C1
+
–
RGRF
R1
f–3dB
+
1
2
p
R1C1
VO
VI
+ǒ
1
)
RF
RG
Ǔǒ
1
1
)
sR1C1
Ǔ
Figure 60. Single-Pole Low-Pass Filter
If even more attenuation is needed, a multiple pole filter is required. The Sallen-Key filter can be used for this
task. For best results, the amplifier should have a bandwidth that is 8 to 10 times the filter frequency bandwidth.
Failure to do this can result in phase shift of the amplifier.
VI
C2
R2R1
C1
RF
RG
R1 = R2 = R
C1 = C2 = C
Q = Peaking Factor
(Butterworth Q = 0.707)
(
=1
Q
2 –)
RGRF
_
+f–3dB
+
1
2
p
RC
Figure 61. 2-Pole Low-Pass Sallen-Key Filter
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
36 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
using the TLV2772 as an accelerometer interface
The schematic, shown in Figure 62, shows the ACH04-08-05 interfaced to the TL V1544 10-bit analog-to-digital
converter (ADC).
The ACH04-08-05 is a shock sensor designed to convert mechanical acceleration into electrical signals. The
sensor contains three piezoelectric sensing elements oriented to simultaneously measure acceleration in three
orthogonal, linear axes (x, y, z). The operating frequency is 0.5 Hz to 5 kHz. The output is buffered with an
internal JFET and has a typical output voltage of 1.80 mV/g for the x and y axis and 1.35 mV/g for the z axis.
Amplification and frequency shaping of the shock sensor output is done by the TLV2772 rail-to-rail operational
amplifier. The TLV2772 is ideal for this application as it offers high input impedance, good slew rate, and
excellent dc precision. The rail-to-rail output swing and high output drive are perfect for driving the analog input
of the TLV1544 ADC.
_
+
1 Axis ACH04–08–05
Shock Sensor
3 V
1.23 V
R1
100 kΩ
C1
0.22 µF
R2
1 MΩ
R3
10 kΩ
1.23 V C2
2.2 nF
R4
100 kΩ
3 V R5
1 kΩ
C3
0.22 µF
1/2
TLV2772
Signal Conditioning
Output to
TLV1544 (ADC)
R6
2.2 kΩ
1.23 V
3 V
TLV431
C
RA
4
81
2
3
Voltage Reference
Figure 62. Accelerometer Interface Schematic
The sensor signal must be amplified and frequency-shaped to provide a signal the ADC can properly convert
into the digital domain. Figure 62 shows the topology used in this application for one axis of the sensor. This
system is powered from a single 3-V supply. Configuring the TLV431 with a 2.2-kΩ resistor produces a reference
voltage of 1.23 V. This voltage is used to bias the operational amplifier and the internal JFETs in the shock
sensor.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
37
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
gain calculation
Since the TL V2772 is capable of rail-to-rail output using a 3-V supply, VO = 0 (min) to 3 V (max). With no signal
from the sensor, nominal VO = reference voltage = 1.23 V. Therefore, the maximum negative swing from nominal
is 0 V – 1.23 V = –1.23 V and the maximum positive swing is 3 V – 1.23 V = 1.77 V . By modeling the shock sensor
as a low impedance voltage source with output of 2.25 mV/g (max) in the x and y axis and 1.70 mV/g (max) in
the z axis, the gain of the circuit is calculated by equation 1.
Gain
+
Output Swing
Sensor Signal
Acceleration (1)
T o avoid saturation of the operational amplifier , the gain calculations are based on the maximum negative swing
of –1.23 V and the maximum sensor output of 2.25 mV/g (x and y axis) and 1.70 mV/g (z axis).
Gain (x, y)
+*
1.23 V
2.25 mV
ń
g
*
50 g
+
10.9 (2)
Gain (z)
+
–1.23 V
1.70 mV
ń
g
–50 g
+
14.5 (3)
and
By selecting R3 = 10 kΩ and R4 = 100 kΩ, in the x and y channels, a gain of 11 is realized. By selecting
R3 = 7.5 kΩ and R4 = 100 kΩ, in the z channel, a gain of 14.3 is realized. The schematic shows the configuration
for either the x- or y-axis.
bandwidth calculation
To calculate the component values for the frequency shaping characteristics of the signal conditioning circuit,
1 Hz and 500 Hz are selected as the minimum required 3-dB bandwidth.
T o minimize the value of the input capacitor (C1) required to set the lower cutoff frequency requires a large value
resistor for R2 is required. A 1-MΩ resistor is used in this example. T o set the lower cutoff frequency, the required
capacitor value for C1 is:
C1
+
1
2
p
fLOW R2
+
0.159 µF (4)
Using a value of 0.22 µF, a more common value of capacitor, the lower cutoff frequency is 0.724 Hz.
To minimize the phase shift in the feedback loop caused by the input capacitance of the TLV2772, it is best to
minimize the value of the feedback resistor R4. However, to reduce the required capacitance in the feedback
loop a large value for R4 is required. Therefore, a compromise for the value of R4 must be made. In this circuit,
a value of 100 kΩ has been selected. To set the upper cutof f frequency, the required capacitor value for C2 is:
C2
+
1
2
p
fHIGH R4
+
3.18 µF (5)
Using a 2.2-nF capacitor, the upper cutoff frequency is 724 Hz.
R5 and C3 also cause the signal response to roll off. Therefore, it is beneficial to design this roll-off point to begin
at the upper cutoff frequency. Assuming a value of 1 kΩ for R5, the value for C3 is calculated to be
0.22 µF.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
38 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
circuit layout considerations
T o achieve the levels of high performance of the TLV277x, follow proper printed-circuit board design techniques.
A general set of guidelines is given in the following.
D
Ground planes—It is highly recommended that a ground plane be used on the board to provide all
components with a low inductive ground connection. However, in the areas of the amplifier inputs and
output, the ground plane can be removed to minimize the stray capacitance.
D
Proper power supply decoupling—Use a 6.8-µF tantalum capacitor in parallel with a 0.1-µF ceramic
capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers
depending on the application, but a 0.1-µF ceramic capacitor should always be used on the supply terminal
of every amplifier. In addition, the 0.1-µF capacitor should be placed as close as possible to the supply
terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less
effective. The designer should strive for distances of less than 0.1 inches between the device power
terminals and the ceramic capacitors.
D
Sockets—Sockets can be used but are not recommended. The additional lead inductance in the socket pins
will often lead to stability problems. Surface-mount packages soldered directly to the printed-circuit board
is the best implementation.
D
Short trace runs/compact part placements—Optimum high performance is achieved when stray series
inductance has been minimized. To realize this, the circuit layout should be made as compact as possible,
thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting input of
the amplifier . Its length should be kept as short as possible. This will help to minimize stray capacitance at
the input of the amplifier.
D
Surface-mount passive components—Using surface-mount passive components is recommended for high
performance amplifier circuits for several reasons. First, because of the extremely low lead inductance of
surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small
size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray
inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be
kept as short as possible.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
39
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
general power dissipation considerations
For a given θJA, the maximum power dissipation is shown in Figure 63 and is calculated by the following formula:
PD
+ǒ
TMAX–TA
q
JA
Ǔ
Where: PD= Maximum power dissipation of TLV277x IC (watts)
TMAX= Absolute maximum junction temperature (150°C)
TA= Free-ambient air temperature (°C)
θJA = θJC + θCA
θJC = Thermal coefficient from junction to case
θCA = Thermal coefficient from case to ambient air (°C/W)
1
0.75
0.5
0
–55–40 –25 –10 5
Maximum Power Dissipation – W
1.25
1.5
MAXIMUM POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
1.75
20 35 50
0.25
TA – Free-Air Temperature – °C
2
65 80 95 110 125
MSOP Package
Low-K Test PCB
θJA = 260°C/W
TJ = 150°C
PDIP Package
Low-K Test PCB
θJA = 104°C/W
SOIC Package
Low-K Test PCB
θJA = 176°C/W
SOT -23 Package
Low-K Test PCB
θJA = 324°C/W
NOTE A: Results are with no air flow and using JEDEC Standard Low-K test PCB.
Figure 63. Maximum Power Dissipation vs Free-Air Temperature
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
40 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
shutdown function
Three members of the TLV277x family (TLV2770/3/5) have a shutdown terminal for conserving battery life in
portable applications. When the shutdown terminal is tied low , the supply current is reduced to 0.8 µA/channel,
the amplifier is disabled, and the outputs are placed in a high impedance mode. To enable the amplifier, the
shutdown terminal can either be left floating or pulled high. When the shutdown terminal is left floating, care
needs to be taken to ensure that parasitic leakage current at the shutdown terminal does not inadvertently place
the operational amplifier into shutdown. The shutdown terminal threshold is always referenced to VDD/2.
Therefore, when operating the device with split supply voltages (e.g. ±2.5 V), the shutdown terminal needs to
be pulled to VDD– (not GND) to disable the operational amplifier.
The amplifier’s output with a shutdown pulse is shown in Figures 48, 49, and 50. The amplifier is powered with
a single 5-V supply and configured as a noninverting configuration with a gain of 5. The amplifier turnon and
turnoff times are measured from the 50% point of the shutdown pulse to the 50% point of the output waveform.
The times for the single, dual, and quad are listed in the data tables. The bump on the rising edge of the TLV2770
output waveform is due to the start-up circuit on the bias generator. For the dual and quad (TLV2773/5), this
bump is attributed to the bias generator’s start-up circuit as well as the crosstalk between the other channel(s),
which are in shutdown.
Figures 55 and 56 show the amplifier’s forward and reverse isolation in shutdown. The operational amplifier is
powered by ±1.35-V supplies and configured as a voltage follower (AV = 1). The isolation performance is plotted
across frequency for both 0.1 VPP and 2.7 VPP input signals. During normal operation, the amplifier would not
be able to handle a 2.7-VPP input signal with a supply voltage of ±1.35 V since it exceeds the common-mode
input voltage range (VICR). However, this curve illustrates that the amplifier remains in shutdown even under
a worst case scenario.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
41
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using Microsim Parts Release 8, the model generation
software used with Microsim PSpice. The Boyle macromodel (see Note 4) and subcircuit in Figure 64 are
generated using the TLV2772 typical electrical and operating characteristics at TA = 25°C. Using this
information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most
cases):
D
Maximum positive output voltage swing
D
Maximum negative output voltage swing
D
Slew rate
D
Quiescent power dissipation
D
Input bias current
D
Open-loop voltage amplification
D
Unity-gain frequency
D
Common-mode rejection ratio
D
Phase margin
D
DC output resistance
D
AC output resistance
D
Short-circuit output current limit
NOTE 4: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
OUT
+
–
+
–
+
–
+
–+
–
+
–+
–
+–
VDD+
rp
IN–2
IN+ 1
GND
rd1
11
j1 j2
10
rss iss
3
12
rd2
ve
54 de
dp
vc
dc
4
C1
53
r2 6
9
egnd
vb
fb
C2
gcm ga vlim
8
5ro1
ro2
hlim
90 dlp
91
dln
92
vlnvlp
99
7
css
* TL V2772 operational amplifier macromodel subcircuit
* created using Parts release 8.0 on 12/12/97 at 10:08
* Parts is a MicroSim product.
*
* connections: noninverting input
* | inverting input
* | | positive power supply
* | | | negative power supply
* | | | | output
* | | | | |
.subckt TLV2772 1 2 3 4 5
*c1 11 12 2.8868E-12
c2 6 7 10.000E–12
css 10 99 2.6302E–12
dc 5 53 dy
de 54 5 dy
dlp 90 91 dx
dln 92 90 dx
dp 4 3 dx
egnd 99 0 poly(2) (3,0) (4,0) 0 .5 .5
fb 7 99 poly(5) vb vc ve vlp vln 0
15.513E6 –1E3 1E3 16E6 –16E6
ga 6 0 11 12 188.50E–6
gcm 0 6 10 99 9.4472E–9
iss 3 10 dc 145.50E–6
hlim 90 0 vlim 1K
j1 11 2 10 jx1
j2 12 1 10 jx2
r2 6 9 100.00E3
rd1 4 11 5.3052E3
rd2 4 12 5.3052E3
ro1 8 5 17.140
ro2 7 99 17.140
rp 3 4 4.5455E3
rss 10 99 1.3746E6
vb 9 0 dc 0
vc 3 53 dc .82001
ve 54 4 dc .82001
vlim 7 8 dc 0
vlp 91 0 dc 47
vln 0 92 dc 47
.model dx D(Is=800.00E–18)
.model dy D(Is=800.00E–18 Rs=1m Cjo=10p)
.model jx1 PJF(Is=2.2500E–12 Beta=244.20E–6
+ Vto=–.99765)
.model jx2 PJF(Is=1.7500E–12 Beta=244.20E–6
+ Vto=–1.002350)
.ends
*$
Figure 64. Boyle Macromodel and Subcircuit
PSpice and Parts are trademarks of MicroSim Corporation.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
42 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
4040047/D 10/96
0.228 (5,80)
0.244 (6,20)
0.069 (1,75) MAX 0.010 (0,25)
0.004 (0,10)
1
14
0.014 (0,35)
0.020 (0,51)
A
0.157 (4,00)
0.150 (3,81)
7
8
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.010 (0,25)
PINS **
0.008 (0,20) NOM
A MIN
A MAX
DIM
Gage Plane
0.189
(4,80)
(5,00)
0.197
8
(8,55)
(8,75)
0.337
14
0.344
(9,80)
16
0.394
(10,00)
0.386
0.004 (0,10)
M
0.010 (0,25)
0.050 (1,27)
0°–8°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-012
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
43
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
DBV (R-PDSO-G5) PLASTIC SMALL-OUTLINE PACKAGE
0,25
0,35
0,55
Gage Plane
0,15 NOM
4073253-4/B 10/97
2,50
3,00
0,40
0,20
1,50
1,80
45
3
3,10
1
2,70
1,00
1,30 0,05 MIN
Seating Plane
0,10
0,95 M
0,25
0°–8°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions include mold flash or protrusion.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
44 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
DBV (R-PDSO-G6) PLASTIC SMALL-OUTLINE PACKAGE
0,25
Gage Plane
0,15 NOM
4073253-5/B 10/97
2,50
3,00
0,40
0,20
1,50
1,80
46
3
3,10
1
2,70
1,30
1,00 0,05 MIN
Seating Plane
0,95 M
0,25
0°–8°
0,10
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions include mold flash or protrusion.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
45
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
DGK (R-PDSO-G8) PLASTIC SMALL-OUTLINE PACKAGE
0,69
0,41
0,25
0,15 NOM
Gage Plane
4073329/A 02/97
4,98
0,25
5
3,05 4,78
2,95
8
4
3,05
2,95
1
0,38
1,07 MAX 0,05 MIN
Seating Plane
0,65 M
0,25
0°–6°
0,10
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
46 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
DGS (S-PDSO-G10) PLASTIC SMALL-OUTLINE PACKAGE
0,69
0,41
0,25
0,15 NOM
Gage Plane
4073272/A 12/97
4,98
0,17
6
3,05 4,78
2,95
10
5
3,05
2,95
1
0,27
0,15
0,05
1,07 MAX
Seating Plane
0,10
0,50 M
0,25
0°–6°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion.
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
47
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER
4040140/D 10/96
28 TERMINAL SHOWN
B
0.358
(9,09)
MAX
(11,63)
0.560
(14,22)
0.560
0.458
0.858
(21,8)
1.063
(27,0)
(14,22)
A
NO. OF
MINMAX
0.358
0.660
0.761
0.458
0.342
(8,69)
MIN
(11,23)
(16,26)
0.640
0.739
0.442
(9,09)
(11,63)
(16,76)
0.962
1.165
(23,83)
0.938
(28,99)
1.141
(24,43)
(29,59)
(19,32)(18,78)
**
20
28
52
44
68
84
0.020 (0,51)
TERMINALS
0.080 (2,03)
0.064 (1,63)
(7,80)
0.307
(10,31)
0.406
(12,58)
0.495
(12,58)
0.495
(21,6)
0.850
(26,6)
1.047
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.035 (0,89)
0.010 (0,25)
121314151618 17
11
10
8
9
7
5
432
0.020 (0,51)
0.010 (0,25)
6
12826 27
19
21
B SQ
A SQ 22
23
24
25
20
0.055 (1,40)
0.045 (1,14)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
48 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE PACKAGE
0.310 (7,87)
0.290 (7,37)
0.014 (0,36)
0.008 (0,20)
Seating Plane
4040107/C 08/96
5
4
0.065 (1,65)
0.045 (1,14)
8
1
0.020 (0,51) MIN
0.400 (10,20)
0.355 (9,00)
0.015 (0,38)
0.023 (0,58)
0.063 (1,60)
0.015 (0,38)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.245 (6,22)
0.280 (7,11)
0.100 (2,54)
0°–15°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification on press ceramic glass frit seal.
E. Falls within MIL-STD-1835 GDIP1-T8
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
49
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
N (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE
20
0.975
(24,77)
0.940
(23,88)
18
0.920
0.850
14
0.775
0.745
(19,69)
(18,92)
16
0.775
(19,69)
(18,92)
0.745
A MIN
DIM
A MAX
PINS **
0.310 (7,87)
0.290 (7,37)
(23.37)
(21.59)
Seating Plane
0.010 (0,25) NOM
14/18 PIN ONLY
4040049/C 08/95
9
8
0.070 (1,78) MAX
A
0.035 (0,89) MAX 0.020 (0,51) MIN
16
1
0.015 (0,38)
0.021 (0,53)
0.200 (5,08) MAX
0.125 (3,18) MIN
0.240 (6,10)
0.260 (6,60)
M
0.010 (0,25)
0.100 (2,54) 0°–15°
16 PIN SHOWN
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001 (20 pin package is shorter then MS-001.)
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
50 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
P (R-PDIP-T8) PLASTIC DUAL-IN-LINE PACKAGE
4040082/B 03/95
0.310 (7,87)
0.290 (7,37)
0.010 (0,25) NOM
0.400 (10,60)
0.355 (9,02)
58
41
0.020 (0,51) MIN
0.070 (1,78) MAX
0.240 (6,10)
0.260 (6,60)
0.200 (5,08) MAX
0.125 (3,18) MIN
0.015 (0,38)
0.021 (0,53)
Seating Plane
M
0.010 (0,25)
0.100 (2,54) 0°–15°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
51
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
4040064/E 08/96
14 PIN SHOWN
Seating Plane
0,05 MIN
1,20 MAX
1
A
7
14
0,19
4,50
4,30
8
6,20
6,60
0,30
0,75
0,50
0,25
Gage Plane
0,15 NOM
0,65 M
0,10
0°–8°
0,10
PINS **
A MIN
A MAX
DIM
2,90
3,10
8
4,90
5,10
14
6,60
6,404,90
5,10
16
7,70
20
7,90
24
9,60
9,80
28
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
TLV277x, TLV277xA
FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT
OPERATIONAL AMPLIFIERS WITH SHUTDOWN
SLOS209F – JANUARY 1998 – REVISED MARCH 2001
52 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
U (S-GDFP-F10) CERAMIC DUAL FLATPACK
4040179/B 03/95
1.000 (25,40)
0.080 (2,03)
0.250 (6,35)
0.250 (6,35)
0.019 (0,48)
0.025 (0,64)
0.300 (7,62)
0.045 (1,14)
0.006 (0,15)
0.050 (1,27)
0.015 (0,38)
0.005 (0,13)
0.026 (0,66)
0.004 (0,10)
0.246 (6,10)
0.750 (19,05)
110
56
0.250 (6,35)
0.350 (8,89)0.350 (8,89)
0.250 (6,35)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only.
E. Falls within MIL STD 1835 GDFP1-F10 and JEDEC MO-092AA
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUAR Y 1997
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE
0.310 (7,87)
0.290 (7,37)
0.014 (0,36)
0.008 (0,20)
Seating Plane
4040107/C 08/96
5
4
0.065 (1,65)
0.045 (1,14)
8
1
0.020 (0,51) MIN
0.400 (10,16)
0.355 (9,00)
0.015 (0,38)
0.023 (0,58)
0.063 (1,60)
0.015 (0,38)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.245 (6,22)
0.280 (7,11)
0.100 (2,54)
0°–15°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
MECHANICAL DATA
MCFP001A – JANUARY 1995 – REVISED DECEMBER 1995
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U (S-GDFP-F10) CERAMIC DUAL FLATPACK
4040179/B 03/95
0.080 (2,03)
0.250 (6,35)
0.019 (0,48)
4 Places
0.300 (7,62) MAX
0.045 (1,14)
0.008 (0,20)
0.050 (1,27)
0.015 (0,38)
0.005 (0,13) MIN
0.026 (0,66)
0.004 (0,10)
0.246 (6,10)
110
56
0.250 (6,35)
0.350 (8,89)0.350 (8,89)
0.250 (6,35)
0.050 (1,27)
Base and Seating Plane
0.280 (7,11)
0.230 (5,84)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only.
E. Falls within MIL STD 1835 GDFP1-F10 and JEDEC MO-092AA
MECHANICAL DATA
MLCC006B – OCTOBER 1996
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER
4040140/D 10/96
28 TERMINAL SHOWN
B
0.358
(9,09)
MAX
(11,63)
0.560
(14,22)
0.560
0.458
0.858
(21,8)
1.063
(27,0)
(14,22)
A
NO. OF
MINMAX
0.358
0.660
0.761
0.458
0.342
(8,69)
MIN
(11,23)
(16,26)
0.640
0.739
0.442
(9,09)
(11,63)
(16,76)
0.962
1.165
(23,83)
0.938
(28,99)
1.141
(24,43)
(29,59)
(19,32)(18,78)
**
20
28
52
44
68
84
0.020 (0,51)
TERMINALS
0.080 (2,03)
0.064 (1,63)
(7,80)
0.307
(10,31)
0.406
(12,58)
0.495
(12,58)
0.495
(21,6)
0.850
(26,6)
1.047
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.035 (0,89)
0.010 (0,25)
12
1314151618 17
11
10
8
9
7
5
432
0.020 (0,51)
0.010 (0,25)
6
12826 27
19
21
B SQ
A SQ 22
23
24
25
20
0.055 (1,40)
0.045 (1,14)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
P (R-PDIP-T8) PLASTIC DUAL-IN-LINE
8
4
0.015 (0,38)
Gage Plane
0.325 (8,26)
0.300 (7,62)
0.010 (0,25) NOM
MAX
0.430 (10,92)
4040082/D 05/98
0.200 (5,08) MAX
0.125 (3,18) MIN
5
0.355 (9,02)
0.020 (0,51) MIN
0.070 (1,78) MAX
0.240 (6,10)
0.260 (6,60)
0.400 (10,60)
1
0.015 (0,38)
0.021 (0,53)
Seating Plane
M
0.010 (0,25)
0.100 (2,54)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
MECHANICAL
MPDI002C – JANUARY 1995 – REVISED DECEMBER 20002
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
N (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE
BB AC AD
0.325 (8,26)
0.300 (7,62)
0.010 (0,25) NOM
Gauge Plane
0.015 (0,38)
0.430 (10,92) MAX
20
1.060
(26,92)
0.940
(23,88)
18
0.920
0.850
14
0.775
0.745
(19,69)
(18,92)
16
0.775
(19,69)
(18,92)
0.745
A MIN
DIM
A MAX
PINS **
(23,37)
(21,59)
Seating Plane
14/18 PIN ONLY
20 pin vendor option 4040049/E 12/2002
9
8
0.070 (1,78) MAX
A
0.035 (0,89) MAX 0.020 (0,51) MIN
16
1
0.015 (0,38)
0.021 (0,53)
0.200 (5,08) MAX
0.125 (3,18) MIN
0.240 (6,10)
0.260 (6,60)
M
0.010 (0,25)
0.100 (2,54)
16 PINS SHOWN
MS-100
VARIATION AA
C
D
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001, except 18 and 20 pin minimum body lrngth (Dim A).
D. The 20 pin end lead shoulder width is a vendor option, either half or full width.
MECHANICAL DATA
MPDS018E – FEBRUAR Y 1996 – REVISED FEBRUAR Y 2002
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DBV (R-PDSO-G5) PLASTIC SMALL-OUTLINE
0,10
M
0,20
0,95
0°–8°
0,25
0,35
0,55
Gage Plane
0,15 NOM
4073253-4/G 01/02
2,60
3,00
0,50
0,30
1,50
1,70
45
31
2,80
3,00
0,95
1,45 0,05 MIN
Seating Plane
5X
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion.
D. Falls within JEDEC MO-178
MECHANICAL DATA
MPDS028B – JUNE 1997 – REVISED SEPTEMBER 2001
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DGK (R-PDSO-G8) PLASTIC SMALL-OUTLINE PACKAGE
0,69
0,41
0,25
0,15 NOM
Gage Plane
4073329/C 08/01
4,98
0,25
5
3,05 4,78
2,95
8
4
3,05
2,95
1
0,38
1,07 MAX
Seating Plane
0,65 M
0,08
0°–6°
0,10
0,15
0,05
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion.
D. Falls within JEDEC MO-187
MECHANICAL DATA
MPDS035A – JANUARY 1998 – REVISED SEPTEMBER 2001
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DGS (S-PDSO-G10) PLASTIC SMALL-OUTLINE PACKAGE
0,69
0,41
0,25
0,15 NOM
Gage Plane
4073272/B 08/01
4,98
0,17
6
3,05 4,78
2,95
10
5
3,05
2,95
1
0,27
0,15
0,05
1,07 MAX
Seating Plane
0,10
0,50 M
0,08
0°–6°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion.
D. Falls within JEDEC MO-187
MECHANICAL DATA
MSOI002B – JANUARY 1995 – REVISED SEPTEMBER 2001
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
8 PINS SHOWN
8
0.197
(5,00)
A MAX
A MIN (4,80)
0.189 0.337
(8,55)
(8,75)
0.344
14
0.386
(9,80)
(10,00)
0.394
16
DIM
PINS **
4040047/E 09/01
0.069 (1,75) MAX
Seating Plane
0.004 (0,10)
0.010 (0,25)
0.010 (0,25)
0.016 (0,40)
0.044 (1,12)
0.244 (6,20)
0.228 (5,80)
0.020 (0,51)
0.014 (0,35)
1 4
8 5
0.150 (3,81)
0.157 (4,00)
0.008 (0,20) NOM
0°– 8°
Gage Plane
A
0.004 (0,10)
0.010 (0,25)0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-012
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,65 M
0,10
0,10
0,25
0,50
0,75
0,15 NOM
Gage Plane
28
9,80
9,60
24
7,90
7,70
2016
6,60
6,40
4040064/F 01/97
0,30
6,60
6,20
80,19
4,30
4,50
7
0,15
14
A
1
1,20 MAX
14
5,10
4,90
8
3,10
2,90
A MAX
A MIN
DIM PINS **
0,05
4,90
5,10
Seating Plane
0°–8°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty . Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2002, Texas Instruments Incorporated
