LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 1. Description The LOPL (LiteOn Power LED) Emitter I is a 1W power LED package which is a point light source with more energy efficient than incandescent and halogen lamps. It gives you total design freedom and unmatched brightness, creating a new opportunities for solid state lighting to displace conventional lighting technologies. Features Applications ! High power LED light source ! Portable lights ! Long life, up to 100k hours ! Traffic signaling ! Instant light (less than 100 ns) ! Backlighting ! Low voltage DC operated ! Interior & exterior automotive lighting ! 110 Lambertian radiation pattern. ! Decorative and landscape lighting ! Low thermal resistance ! Medical illumination ! RoHS Compliant 2. Outline Dimensions of Emitter Notes 1. All dimensions are in millimeters. 2. Tolerance is 0.2 mm (.008") unless otherwise noted. Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 1 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 3. Outline Dimensions Notes 1. All dimensions are in millimeters. 2. Tolerance is 0.2 mm (.008") unless otherwise noted. Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 2 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 4. Rating and Characteristics 4.1 Absolute Maximum Ratings at Ta=25C Parameter Symbol Rating Unit Power Dissipation Po 1.15 W Forward Current IF 350 mA Forward Pulse Current IFP 500 mA Reverse Voltage VR 5 V Junction Temperature Tj 125 C Rth, J-C 13.7 C/W Operating Temperature Range Topr -40 - 80 C Storage Temperature Range Tstg -40 - 120 C Soldering Condition 1, 2 Tsol Thermal Resistance, Junction-Case 260C For 5 Seconds Notes 1. Proper current derating must be observed to maintain junction temperature below the maximum. For more information, consult the LOPL Emitters application notes, available upon request. 2. Measured at leads, during lead soldering and heat pad attach, body temperature must not exceed 120C. LOPL Emitters can't be soldered by general IR or Vapor phase reflow, nor by wave soldering. Lead soldering is limited to selective heating of the leads, such as by hot bar reflow or hand soldering. Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 3 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 4.2 Electro-Optical Characteristics at Ta=25C Parameter Symbol MIN. TYP. MAX. Test Condition Unit Forward Voltage VF 2.07 2.57 3.27 IF= 350mA V Reverse Current IR 100 VR = 5V A Luminous Flux 1 V 44.0 IF = 350mA lm Viewing Angle 2 21/2 110 IF = 350mA IF = 350mA nm Dominant Wavelength D 39.8 613 617 620 Temperature Coefficient of D TC 0.06 IF = 350mA, Topr nm/C Temperature Coefficient of VF TCV -2.0 IF = 350mA, Topr mV/C Notes 1. Luminous flux is the total luminous flux output as measured with an integrating sphere. 2. Viewing angle is the off-axis angle at which the luminous intensity is half the axial luminous intensity. Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 4 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 4.3 Typical Electrical / Optical Characteristics Curves 100% Relative Intensity (%) 80% 60% 40% 20% 0% 400 450 500 550 600 Wavelength (nm) 650 700 750 Fig 1. Relative Spectrum of Emission 0 100% 90% 30 Relative Intensity (%) 80% 70% 60% 60 50% 40% 30% 20% 10% 0% 90 60 30 0 50 100% Fig 2. Radiation Characteristics Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 5 of 12 LITE-ON TECHNOLOGY CORPORATION 400 400 300 300 Forward Current IF (mA) Forward Current IF (mA) Property of Lite-On Only 200 200 100 100 0 0 1.5 2.0 2.5 Forward Voltage VF (V) 3.0 0 40 80 120 Ambient Temperature (C) Fig 3. Forward Current Fig 4. Forward Current Derating Curve 100% 619.0 80% 618.5 Dominant Wavelength (nm) Relative Luminous Flux Rth, J-C=60C/W Rth, J-C=50C/W Rth, J-C=40C/W Rth, J-C=30C/W 60% 40% 618.0 617.5 617.0 20% 616.5 0% 0 100 200 300 Forward Current IF (mA) Fig 5. Relative Luminous Flux Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 400 0 100 200 300 400 Forward Current IF (mA) Fig 6. Wavelength Shift Page: 6 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 5 Category Code Table R F H1 Dominant Wavelength Categories Code H1 Min 613 Max 620 Forward Voltage Categories Code D E F G H Min 2.07 2.31 2.55 2.79 3.03 Max 2.31 2.55 2.79 3.03 3.27 Luminous Flux Categories Code R S Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Min 39.8 51.7 Max 51.7 67.2 Page: 7 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 6. Recommend Solder Pad 1.6 x 2.65 Solder Pad 1.1 8 O 0.05 15.05 Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 8 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 7. Package Dimensions Packaging Trays including 30pcs products Inner Boxes including 17pcs trays Outer Carton including 8pcs boxes Note: 1. 4080pcs per Carton. 2. Tray 16.0 x 29.3 cm Inner Carton: 30 x 16.5 x 13 cm Outer Carton: 61.8 x 35 x 29.5 cm Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 9 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 8. Cautions 8.1 Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon's Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 8.2 Storage The storage ambient for the LEDs should not exceed 30C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are soldered within one week. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient. LEDs stored out of their original packaging for more than a week should be baked at about 60 deg C for at least 24 hours before solder assembly. 8.3 Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. LED Circuit model A LED Circuit model B (A) Recommended circuit. (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 10 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 8.4 ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: ! Use a conductive wrist band or anti-electrostatic glove when handling these LEDs. ! All devices, equipment, and machinery must be properly grounded. ! Work tables, storage racks, etc. should be properly grounded. ! Use ion blower to neutralize the static charge which might have built up on surface of the LED's plastic lens as a result of friction between LEDs during storage and handling. ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or "no light up" at low currents. To verify for ESD damage, check for "light up" and VF of the suspect LEDs at low currents. The VF of "good" LEDs should be >2.0V@0.1mA for InGaN product. 8.5 Suggested Checking List Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 5. All wrist strap or heel strap checkers calibration up to date? Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 11 of 12 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycles? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No.: LOPL-E011HA DATA SHEET BNC-OD-C131/A4 Page: 12 of 12