Ordering number:EN2719 N-Channel Silicon MOSFET 2SK1067 FM Tuner, VHF-Band Amplifier Applications Package Dimensions unit:mm 2057 0.3 0.15 0.2 [2SK1067] 3 0 to 0.1 0.425 2.1 1.250 * Low noise NF=1.8dB typ (f=100MHz). * High power gain PG=27dB typ (f=100MHz). * Small reverse transfer capacitance Crss=0.035pF (VDS=10V, f=1MHz). * Ultrasmall-sized package (MCP) permitting 2SK1067-applied sets to be made smaller and slimmer. 0.425 Features 1 2 0.65 0.65 2.0 0.3 0.6 0.9 1 : Gate 2 : Drain 3 : Source SANYO : MCP Specifications Absolute Maximum Ratings at Ta = 25C Parameter Symbol Drain-to-Source Voltage Conditions Ratings Unit VDS VGS 5 V ID 30 mA PD Tch 150 mW Channel Temperature 125 C Storage Temperature Tstg -55 to +125 C Gate-to-Source Voltage Drain Current Allowable Power Dissipation 16 V Electrical Characteristics at Ta = 25C Parameter Symbol Drain-to-Source Voltage Gate-to-Source Leakage Current Zero-Gate Voltage Drain Current Cutoff Voltage Forward Transfer Admittance Conditions Ratings min VDSX IGSS VGS=-4V, ID=100A VDS=0V, VGS=5V 16 IDSS VGS(off) | yfs | VDS=10V, VGS=0 VDS=10V, ID=100A 1.2* Input Capacitance Ciss VDS=10V, VGS=0, f=1kHz VDS=10V, VGS=0, f=1MHz Reverse Transfer Capacitance Crss VDS=10V, VGS=0, f=1MHz 3 3.0 2.5 4 6.0 5.0 5 max Unit V 10 nA 12.0* mA -2.5 * : The 2SK1067 is classified by IDSS as follows (unit : mA) : 1.2 typ V 11 mS 2.3 pF 0.035 pF Continued on next page. 12.0 (Note) Marking : CJ IDSS rank : 3, 4, 5 Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 51099TH (KT)/N158MO, TS No.2719-1/5 2SK1067 Continued from preceding page. Parameter Symbol Power Gain PG Noise Figure NF Conditions VDS=10V, VGS=0, f=100MHz, See specified Test Circuit VDS=10V, VGS=0, f=100MHz, See specified Test Circuit Ratings Unit 27 dB 1.8 3.0 dB PG, NF Specified Test Circuit No.2719-2/5 2SK1067 No.2719-3/5 2SK1067 No.2719-4/5 2SK1067 Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of May, 1999. Specifications and information herein are subject to change without notice. PS No.2719-5/5