1.6X0.8mm SMD CHIP LED LAMP Part Number: APT1608QBC/D-AMT Blue ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Description The Blue source color devices are made with InGaN Light Emitting Diode. Features Static electricity and surge damage the LEDS. z High reliability LED package. It is recommended to use a wrist band or anti-electrostatic z 1.6mmx0.8mm SMT LED,0.75mm thickness glove when handling the LEDs. z Low power consumption. All devices, equipment and machinery must be electrically z Wide viewing angle. grounded. z Ideal for backlight and indicator. z Various colors and lens types available. Applications z Package: 2000pcs / reel . z Traffic signaling. z Moisture sensitivity level : level 3. z Backlighting (illuminated advertising , general lighting). z RoHS compliant. z Interior and exterior automotive lighting. z Substitution of micro incandescent lamps. z Reading lamps. z Signal and symbol luminaire for orientation. z Marker lights (e.g. Steps, exit ways, etc). z Decorative and entertainment lighting. Package Dimensions z Indoor and outdoor commercial and residential architectural lighting. Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL3994 REV NO: V.1 DATE: NOV/22/2010 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP:1203010850 Selection Guide Part No. Dice APT1608QBC/D-AMT Iv (mcd) [2] @ 20mA Lens Type Code. Min. Max. G 40 55 H 55 80 M 80 120 N 120 200 Water Clear Blue (InGaN) Viewing Angle [1] 21/2 120 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. Absolute Maximum Ratings at Ta=25C Parameter Symbol Value Unit Power dissipation PD 80 mW Reverse Voltage VR 5 V Junction temperature TJ 110 C Operating Temperature Top -40 To +100 C Storage Temperature Tstg -40 To +110 C IF 20 mA IFM 150 mA 250 V 330 C/W DC Forward Current[1] Peak Forward Current [2] Electrostatic Discharge Threshold (HBM) Thermal Resistance (Junction/ambient) [1] Rth j-a Notes: 1. Rth(j-a) Results from mounting on PC board FR4 (pad size16 mm 2 per pad), 2. 1/10 Duty Cycle, 0.1ms Pulse Width. Electrical / Optical Characteristics at Ta=25C Parameter Symbol Wavelength at peak emission Dominant Wavelength Spectral bandwidth at 50% Forward Voltage IF=20mA IF=20mA REL MAX IF=20mA IF=20mA Value Code. Min. peak dom [1] Typ. Max. 468 nm 1B 461 468 2A 464 471 2B 467 473 3A 469 475 3B 471 477 25 VF [2] 3.3 Unit nm nm 4.0 V 50 uA Reverse Current (VR = 5V) IR Temperature coefficient of peak IF=20mA, -10 C T100 C TC peak 0.06 nm/ C Temperature coefficient of dom IF=20mA, -10 C T100 C TC dom 0.03 nm/ C Temperature coefficient of VF IF=20mA, -10 C T100 C TCV -3.2 mV/ C Notes: 1.The dominant Wavelength ( d) above is the setup value of the sorting machine. (Tolerance d : 1nm. ) 2. Forward Voltage: +/-0.1V. SPEC NO: DSAL3994 REV NO: V.1 DATE: NOV/22/2010 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP:1203010850 Blue APT1608QBC/D-AMT SPEC NO: DSAL3994 REV NO: V.1 DATE: NOV/22/2010 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP:1203010850 APT1608QBC/D-AMT Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: 0.1) Tape Specifications (Units : mm) Reel Dimension SPEC NO: DSAL3994 REV NO: V.1 DATE: NOV/22/2010 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP:1203010850 PACKING & LABEL SPECIFICATIONS APT1608QBC/D-AMT SPEC NO: DSAL3994 REV NO: V.1 DATE: NOV/22/2010 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP:1203010850 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below Lot Tolerance Percent Defective (LTPD) : 10% No. Test Item Standards Test Times / Number of Cycles Damaged Test Condition 1 Continuous operating test - Ta =25C ,IF = maximum rated current* 1,000 h 0 / 22 2 High Temp. operating test EIAJ ED4701/100(101) Ta = 100C IF = maximum rated current* 1,000 h 0 / 22 3 Low Temp. operating test - Ta = -40C, IF = maximum rated current* 1,000 h 0 / 22 4 High temp. storage test EIAJ EDTa = maximum rated storage temperature 4701/100(201) 1,000 h 0 / 22 5 Low temp. storage test EIAJ ED4701/100(202) Ta = -40C 1,000 h 0 / 22 6 High temp. & humidity storage test EIAJ ED4701/100(103) Ta = 60C, RH = 90% 1,000 h 0 / 22 7 High temp. & humidity operating test EIAJ ED4701/100(102) Ta = 60C, RH = 90% IF = maximum rated current* 1,000 h 0 / 22 8 Soldering reliability test EIAJ ED4701/100(301) Moisture soak : 30C,70% RH, 72h Preheat : 150~180C(120s max.) Soldering temp : 260C(10s) 3 times 0 / 18 9 Thermal shock operating test - Ta = -40C(15min) ~ 100C(15min) IF = derated current at 100C 1,000 cycles 0 / 22 10 Thermal shock test - Ta = -40C(15min) ~ maximum rated storage temperature(15min) 1,000 cycles 0 / 22 11 Electric Static Discharge (ESD) EIAJ ED4701/100(304) C = 100pF , R2 = 1.5K V = 250V Once each Polarity 0 / 22 12 Vibration test - a = 196m/s , f = 100~2KHz , t = 48min for all xyz axes 4 times 0 / 22 * : Refer to forward current vs. derating curve diagram Failure Criteria Items Symbols Conditions Failure Criteria luminous Intensity lv IF = 20mA Testing Min. Value <Spec.Min.Value x 0.5 Forward Voltage VF IF = 20mA Testing Max. Value Spec.Max.Value x 1.2 Reverse Current IR VR = Maximum Rated Reverse Voltage Testing Max. Value Spec.Max.Value x 2.5 High temp. storage test - - Occurrence of notable decoloration, deformation and cracking SPEC NO: DSAL3994 REV NO: V.1 DATE: NOV/22/2010 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.HAN ERP:1203010850