CAT.8100D
ALUMINUM ELECTROLYTIC CAPACITORS
U
1
W
2
X
3
1
4
C
5
1
6
0
7
0
8
M
9
C
10
L
11
1
12
G
13
B
14
Configuration
Taping code
Size code
Capacitance tolerance (±20%)
Rated capacitance
(
10µF
)
Rated voltage
(
16V
)
Series name
Type
φD
3
4 to 8
Code
2
1
1. Voltage mark for 6.3V is 6V .
In case of marking for φ3 units, “V” for rated voltage is omitted.
2. In case of marking for φ3 units, Lot No.is expressed by a digit (month code).
0.5 to 0.8
Capacitance
1 Voltage
2 Lot No.
X2
10
16V
Plastic platform
0.3 MAX.
5.4 +0.1
–0.2
φD0.5
B0.2
C0.2
0.5 MAX.
A0.2 A0.2
E
Positive
Negative
φD
3
A
B
C
E
1.5
3.3
3.3
0.8
1.8
4.3
4.3
1.0
2.1
5.3
5.3
1.3
2.4
6.6
6.6
2.2
4 5
(mm)
6.3
3.3
8.3
8.3
2.3
8
U
1
W
2
X
3
1
4
C
5
1
6
0
7
0
8
M
9
C
10
L
11
1
12
G
13
B
14
Configuration
Taping code
Size code
Capacitance toleranc (20%)
Rated capacitance
(
10F
)
Rated voltage
(
16V
)
Series name
Type
φD
3
4 to 8
Code
2
1
1. Voltage mark for 6.3V is 6V .
In case of marking for φ3 units, “V” for rated voltage is omitted.
2. In case of marking for φ3 units, Lot No.is expressed by a digit (month code).
0.5 to 0.8
Capacitance
1 Voltage
2 Lot No.
A2
10
16V
Plastic platform
0.3 MAX.
5.4 +0.1
–0.2
φD±0.5
B±0.2
C±0.2
0.5 MAX.
A±0.2 A±0.2
E
Positive
Negative
φD
3
A
B
C
E
1.5
3.3
3.3
0.8
1.8
4.3
4.3
1.0
2.1
5.3
5.3
1.3
2.4
6.6
6.6
2.2
4 5
(mm)
6.3
3.3
8.3
8.3
2.3
8
WX series
5.5mmL Chip Type
Chip type with 5.5mm height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Load life of 2000 hours at 85
°C
.
Compliant to the RoHS directive (2011/65/EU).
Chip Type Type numbering system (Example : 16V 10
µ
F)
Specifications
Category
Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Resistance to soldering
heat
Marking
Performance CharacteristicsItem
–40 to +85°C
4 to 50V
0.1 to 330µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) ,whichever is greater.
Black print on the case top.
Values in ( ) applicable to WR, φ3 case size.
Measurement frequency : 120Hz
The specifications listed at right shall be met
when the capacitors are restored to 20°C after
the rated voltage is applied for 2000 hours at
85°C.
Shelf Life After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Rated voltage (V)
tan δ (MAX.)
6.3
0.26 (0.30)
10
0.20 (0.24)
16
0.16 (0.19)
25
0.14 (0.16)
35
0.12 (0.14)
50
0.12 (0.14)
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
4
7
15
6.3
4
8
10
3
8
16
2
4
25
2
4
35
2
3
50
2
3
WX
WT
Bi-polarized
WP
Measurement frequency : 120Hz at 20°C
4
0.35 (0.40)
High
Te m p e ra t ure
Capacitance change
Leakage Current
tan δ
Within ±20% of the initial capacitance value (Within ±25% for 4 V and φ3,WR series units)
200
%
or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
Leakage current
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Dimension table in next page.
WJ
High
Tem p reflow
•
In the case of size φ3 in ( ),parentheses, use WX in the 2nd and 3rd
digit and put a
in the 12th digit of type numbering system.
ZS
Smaller
2