FastEdgeTM Series CY2PP3210 Dual 1:5 Differential Clock/Data Fanout Buffer Features Functional Description * Dual sets of five ECL/PECL differential outputs * Two ECL/PECL differential inputs * Hot-swappable/-insertable * 50 ps output-to-output skew * 150 ps device-to-device skew * 500 ps propagation delay (typical) * 0.8 ps RMS period jitter (max.) * 1.5 GHz Operation (2.2 GHz max. toggle frequency) * PECL mode supply range: VCC = 2.5V 5% to 3.3V5% with VEE = 0V * ECL mode supply range: VE E = -2.5V 5% to -3.3V5% with VCC = 0V * Industrial temperature range: -40C to 85C * 32-pin 1.4-mm TQFP package * Temperature compensation like 100K ECL * Pin compatible with MC100ES6210 The CY2PP3210 is a low-skew, low propagation delay dual 1-to-5 differential fanout buffer targeted to meet the requirements of high-performance clock and data distribution applications. The device is implemented on SiGe technology and has a fully differential internal architecture that is optimized to achieve low signal skews at operating frequencies of up to 1.5 GHz. The device features two differential input paths that are differential internally. The CY2PP3210 may function not only as a differential clock buffer but also as a signal-level translator and fanout distributing a single-ended signal. An external bias pin, VBB, is provided for this purpose. In such an application, the VBB pin should be connected to either one of the CLKA# or CLKB# inputs and bypassed to ground via a 0.01-F capacitor. Traditionally, in ECL, it is used to provide the reference level to a receiving single-ended input that might have a differential bias point. Since the CY2PP3210 introduces negligible jitter to the timing budget, it is the ideal choice for distributing high frequency, high precision clocks across back-planes and boards in communication systems. Furthermore, advanced circuit design schemes, such as internal temperature compensation, ensure that the CY2PP3210 delivers consistent performance over various platforms. Block Diagram Pin Configuration QA0 QA0# QA3 QA3# QA4 QA4# QB0 QB0# CLKB QB1 QB1# VCC VCC QA0 QA0# QA1 QA1# QA2 QA2# VCC VCC NC CLKA CLKA# VBB CLKB CLKB# VEE QB2 QB2# CLKB# VEE 1 2 3 4 5 6 7 8 CY2PP3210 24 23 22 21 20 19 18 17 QA3 QA3# QA4 QA4# QB0 QB0# QB1 QB1# 9 10 11 12 13 14 15 16 VEE 32 31 30 29 28 27 26 25 QA2 QA2# CLKA# VCC QB4# QB4 QB3# QB3 QB2# QB2 VCC CLKA QA1 QA1# VCC QB3 QB3# QB4 QB4# VBB Cypress Semiconductor Corporation Document #: 38-07508 Rev.*C * 3901 North First Street * San Jose, CA 95134 * 408-943-2600 Revised July 28, 2004 FastEdgeTM Series CY2PP3210 Pin Definitions[1, 2, 3] Pin Name 2 NC 3 CLKA, 4 CLKA# 5 VBB[3] I/O[1] Type I,PD ECL/PECL Description No connect. I,PD/PU ECL/PECL ECL/PECL Differential Input Clocks. ECL/PECL Differential Input Clocks. O Bias Reference Voltage Output. I,PD ECL/PECL ECL/PECL Differential Input Clocks. I,PD/PU ECL/PECL ECL/PECL Differential Input Clocks. 6 CLKB, 7 CLKB# 8 VEE[2] -PWR Power Negative Supply. VCC +PWR Power Positive Supply. 31,29,27,24,22 QA(0:4) O ECL/PECL True output 30,28,26,23,21 QA#(0:4) O ECL/PECL Complement output 20,18,15,13,11 QB(0:4) O ECL/PECL True output 19,17,14,12,10 QB#(0:4) O ECL/PECL Complement output 1,9,16,25,32 Governing Agencies The following agencies provide specifications that apply to the CY2PP3210. The agency name and relevant specification is listed below in Table 2. Table 1. Agency Name Specification JEDEC JESD 020B (MSL) JESD 51 (Theta JA) JESD 8-2 (ECL) JESD 65-B (skew,jitter) Mil-Spec 883E Method 1012.1 (Thermal Theta JC) Notes: 1. In the I/O column, the following notation is used: I for Input, O for Output, PD for Pull-Down, PU for Pull-Up, and PWR for Power 2. In ECL mode (negative power supply mode), VEE is either -3.3V or -2.5V and VCC is connected to GND (0V). In PECL mode (positive power supply mode), VEE is connected to GND (0V) and VCC is either +3.3V or +2.5V. In both modes, the input and output levels are referenced to the most positive supply (VCC) and are between VCC and VEE. 3. VBB is available for use for single-ended bias mode for |3.3V| supplies (not |2.5V|). Document #: 38-07508 Rev.*C Page 2 of 9 FastEdgeTM Series CY2PP3210 Absolute Maximum Ratings Parameter Description Condition Min. Max. Unit VCC Positive Supply Voltage Non-Functional -0.3 4.6 V VEE Negative Supply Voltage Non-Functional -4.6 0.3 V TS Temperature, Storage Non-Functional -65 +150 C TJ Temperature, Junction Non-Functional 150 C ESDh ESD Protection Human Body Model MSL Moisture Sensitivity Level Gate Count Total Number of Used Gates 2000 V 3 N.A. 50 gates Assembled Die Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required. Operating Conditions Parameter Description Condition IBB Output Reference Current LUI Latch Up Immunity Functional, typical TA Temperature, Operating Ambient Functional Relative to VBB Min. Max. Unit - |200| uA 100 +85 OJc Dissipation, Junction to Case Functional 29[4] OJa Dissipation, Junction to Ambient Functional 76[4] IEE Maximum Quiescent Supply Current CIN Input pin capacitance LIN Pin Inductance VIN Input Voltage VEE pin[5] Relative to VCC[6] VTT Output Termination Voltage Relative to VCC Output Voltage Relative to VCC[6] IIN Input C C/W C/W - 130 mA - 3 pF 1 nH -0.3 VCC + 0.3 V [6] VOUT Current[7] mA -40 VCC - 2 -0.3 V VCC + 0.3 V l150l uA Min. Max. Unit 2.375 3.135 2.625 3.465 V V VIN = VIL, or VIN = VIH PECL DC Electrical Specifications Parameter Description Condition VCC Operating Voltage 2.5V 5%, VEE = 0.0V 3.3V 5%, VEE = 0.0V VCMR Differential Cross Point Voltage[8] Differential operation VOH Output High Voltage IOH = -30 mA[9] VOL Output Low Voltage VCC = 3.3V 5% VCC = 2.5V 5% IOL = -5 mA[9] VIH Input Voltage, High Single-ended operation VIL Input Voltage, Low Single-ended operation VBB[3] Output Reference Voltage Relative to VCC[6] 1.2 VCC V VCC - 1.25 VCC - 0.7 V VCC - 1.995 VCC -1.995 VCC - 1.5 VCC - 1.3 V V VCC - 1.165 VCC - 0.880 [10] V VCC - 1.625 V VCC - 1.220 V VCC - 1.945 [10] VCC - 1.620 Notes: 4. Theta JA EIA JEDEC 51 test board conditions (typical value); Theta JC 883E Method 1012.1 5. Power Calculation: VCC * IEE +0.5 (IOH + IOL) (VOH - VOL) (number of differential outputs used); IEE does not include current going off chip. 6. where VCC is 3.3V5% or 2.5V5% 7. Inputs have internal pull-up/pull-down or biasing resistors which affect the input current. 8. Refer to Figure 1 9. Equivalent to a termination of 50 to VTT. IOHMIN=(VOHMIN-VTT)/50; IOHMAX=(VOHMAX-VTT)/50; IOLMIN=(VOLMIN-VTT)/50; IOLMAX=(VOLMAX-VTT)/50; 10. VIL will operate down to VEE; VIH will operate up to VCC Document #: 38-07508 Rev.*C Page 3 of 9 FastEdgeTM Series CY2PP3210 ECL DC Electrical Specifications Parameter Description Condition VEE Negative Power Supply VCMR Differential cross point voltage[8] Differential operation VOH Output High Voltage IOH = -30 mA[9] VOL Output Low Voltage VEE = -3.3V 5% VEE = -2.5V 5% IOL = -5 mA[9] VIH Input Voltage, High Single-ended operation -2.5V 5%, VCC = 0.0V -3.3V 5%, VCC = 0.0V VIL Input Voltage, Low VBB[3] Output Reference Voltage Single-ended operation Min. Max. Unit -2.625 -3.465 -2.375 -3.135 V VEE + 1.2 0V V -1.25 -0.7 V -1.995 -1.995 -1.5 -1.3 V -1.165 -0.880 [10] V [10] -1.945 -1.625 V - 1.620 - 1.220 V Min. Max. Unit 0.1 1.3 V 1.5 GHz 750 ps AC Electrical Specifications Parameter Description Voltage[8] Condition VPP Differential Input FCLK Input Frequency 50% duty cycle Standard load TPD Propagation Delay CLKA or CLKB to Output pair 660 MHz [11] Vo Output Voltage (peak-to-peak; see Figure 2) VCMRO Output Common Voltage Range (typ.) tsk(0) Output-to-output Skew 660 MHz [11], See Figure 3 - 50 ps tsk(PP) Part-to-Part Output Skew 660 MHz [11] - 150 ps 660 MHz [11] - 0.8 ps - 50 ps 0.08 0.3 ns TPER Output Period Jitter (rms)[12] Skew[13] tsk(P) Output Pulse TR,TF Output Rise/Fall Time (see Figure 2) Differential operation 280 < 1 GHz 0.375 - VCC - 1.425 660 MHz [11], See Figure 3 660 MHz 50% duty cycle Differential 20% to 80% V V Timing Definitions VCC VCM R Max = VCC VIH VPP VPP range 0.1V - 1.3V VCM R VIL VCMR M in = VEE + 1.2 VEE Figure 1. PECL/ECL Input Waveform Definitions Notes: 11. 50% duty cycle; standard load; differential operation 12. For 3.3V supplies. Jitter measured differentially using an Agilent 8133A Pulse Generator with an 8500A LeCroy Wavemaster Oscilloscope using at least 10,000 data points 13. Output pulse skew is the absolute difference of the propagation delay times: | tPLH - tPHL |. Document #: 38-07508 Rev.*C Page 4 of 9 FastEdgeTM Series CY2PP3210 tr, tf, 20-80% VO Figure 2. ECL/LVPECL Output In p u t C lo c k V P P TP L H , TP H L T P D O u tp u t C lo c k V O tS K (O ) A n o th e r O u tp u t C lo c k Figure 3. Propagation Delay (TPD), output pulse skew (|tPLH-tPHL|), and output-to-output skew (tSK(O)) for both CLKA or CLKB to Output Pair, PECL/ECL to PECL/ECL Test Configuration Standard test load using a differential pulse generator and differential measurement instrument. VTT VTT RT = 50 ohm RT = 50 ohm P u ls e G e n e ra to r Z = 50 ohm 5" Zo = 50 ohm Zo = 50 ohm 5" RT = 50 ohm DUT CY2PP3210 VTT RT = 50 ohm VTT Figure 4. CY2PP318 AC Test Reference Document #: 38-07508 Rev.*C Page 5 of 9 FastEdgeTM Series CY2PP3210 Applications Information Termination Examples CY2PP3210 VTT VCC RT = 50 ohm 5" Zo = 50 ohm 5" RT = 50 ohm VTT VEE Figure 5. Standard LVPECL - PECL Output Termination CY2PP3210 VTT RT = 50 ohm VCC 5" Zo = 50 ohm 5" VTT R T = 50 ohm V B B (3 .3 V ) VEE Figure 6. Driving a PECL/ECL Single-ended Input CY2PP3210 3 .3 V V C C = 3 .3 V 120 ohm LVDS 5" Zo = 50 ohm 33 ohm ( 2 p la c e s ) 5" 120 ohm 3 .3 V VEE = 0V 51 ohm ( 2 p la c e s ) L V P E C L to LVDS Figure 7. Low-voltage Positive Emitter-coupled Logic (LVPECL) to a Low-voltage Differential Signaling (LVDS) Interface Document #: 38-07508 Rev.*C Page 6 of 9 FastEdgeTM Series CY2PP3210 VDD-2 VCC X Y Z One output is shown for clarity Figure 8. Termination for LVPECL to HTSL interface for VCC=2.5V would use X=50 Ohms, Y=2300 Ohms, and Z=1000 Ohms. See application note titled, "PECL Translation, SAW Oscillators, and Specs" for other signalling standards and supplies. Ordering Information Part Number Package Type Product Flow CY2PP3210AI 32-pin TQFP Industrial, -40 to 85C CY2PP3210AIT 32-pin TQFP - Tape and Reel Industrial, -40 to 85C Document #: 38-07508 Rev.*C Page 7 of 9 FastEdgeTM Series CY2PP3210 Package Drawing and Dimension 32-Lead Thin Plastic Quad Flatpack 7 x 7 x 1.4 mm A32.14 Dimensions are in mm 51-85088-*B FastEdge is a trademark of Cypress Semiconductor. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-07508 Rev.*C Page 8 of 9 (c) Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. FastEdgeTM Series CY2PP3210 Document History Page Document Title: CY2PP3210 FastEdgeTM Series Dual 1:5 Differential Clock/Data Fanout Buffer Document Number: 38-07508 REV. ECN NO. Issue Date Orig. of Change ** 122396 02/12/03 RGL New Data Sheet *A 125458 04/17/03 RGL Corrected pins 26 to 31 from Q2#, Q2, Q1#, Q1, Q0#, Q0 to QA2#, QA2, QA1#, QA1,QA0#, QA0 in the Pin Configuration diagram Changed pins 9, 16, 25, 32 from VCC to VCCO Changed the title to FastEdgeTM Series Dual 1:5 Differential Clock/Data Fanout Buffer RGL Supplied data to all the TBD's to match the device *B 229370 See ECN *C 247616 See ECN Document #: 38-07508 Rev.*C Description of Change RGL/GGK Changed VOH and VOL to match the Char Data Page 9 of 9