TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 LOW POWER NPN SILICON TRANSISTOR Qualified per MIL-PRF-19500/391 DEVICES LEVELS 2N3019 2N3019S 2N3057A 2N3700 2N3700S 2N3700UB JAN JANTX JANTXV JANS ABSOLUTE MAXIMUM RATINGS (TC = +25C unless otherwise noted) Parameters / Test Conditions Symbol Value Unit Collector-Emitter Voltage VCEO 80 Vdc Collector-Base Voltage VCBO 140 Vdc Emitter-Base Voltage VEBO 7.0 Vdc IC 1.0 Adc Collector Current Total Power Dissipation @ TA = +25C (1) @ TC = +25C (2) W 2N3019; 2N3019S 2N3057A 2N3700, 2N3700UB 2N3019; 2N3019S 2N3057A 2N3700 2N3700UB Operating & Storage Jct Temp Range PT 0.8 0.5 0.5 TJ, Tstg 5.0 1.8 1.0 N/A -65 to +200 TO-39 (TO-205AD) 2N3019, 2N3019S W C TO-18 (TO-206AA) 2N3700 NOTE: 1) Derate linearly 4.6 mW/C for type 2N3019 and 2N3019S; 2.3 mW/C for type 2N3057A; 2.85 mW/C for type 2N3700; 6.6 mW/C for type 2N3700UB for TA +25C 2) Derate linearly 28.6 mW/C for type 2N3019 and 2N3019S; 10.3 mW/C for types 2N3057A, 2N3700 & 2N3700UB for TC +25C. ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted) Parameters / Test Conditions OFF CHARACTERTICS Collector-Emitter Breakdown Current IC = 30mAdc Collector-Emitter Cutoff Current VCE = 90Vdc Collector-Base Cutoff Current VCB = 140V Emitter-Base Cutoff Current VEB = 7.0Vdc VEB = 5.0Vdc T4-LDS-0185 Rev. 1 (101726) Symbol Min. V(BR)CEO 80 Max. Unit Vdc ICES 10 Adc ICBO 10 Adc 10 Adc Adc IEBO TO-46 (TO-206AB) 2N3057A 3 PIN SURFACE MOUNT 2N3700UB Page 1 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted) (CONT.) Parameters / Test Conditions Symbol Min. Max. ON CHARACTERTICS Forward-Current Transfer Ratio IC = 150mAdc, VCE = 10Vdc 100 300 IC = 0.1mAdc, VCE = 10Vdc 50 300 hFE IC = 10mAdc, VCE = 10Vdc 90 IC = 500mAdc, VCE = 10Vdc 50 IC = 1.0Adc, VCE = 10Vdc 15 Collector-Emitter Saturation Voltage IC = 150mAdc, IB = 15mAdc Base-Emitter Saturation Voltage IC = 150mAdc, IB = 15mAdc 300 0.2 VCE(sat) IC = 500mAdc, IB = 50mAdc Unit Vdc 0.5 VBE(sat) 1.1 Vdc Unit DYNAMIC CHARACTERISTICS Parameters / Test Conditions Small-Signal Short-Circuit Forward Current Transfer Ratio IC = 1.0mAdc, VCE = 5.0Vdc, f = 1.0kHz Symbol Min. Max. hfe 80 400 Magnitude of Small-Signal Short-Circuit Forward Current Transfer Ratio IC = 50mAdc, VCE = 10Vdc, f = 20MHz |hfe| 5.0 20 Output Capacitance VCB = 10Vdc, IE = 0, 100 kHz f 1.0MHz Cobo 12 pF Input Capacitance VEB = 0.5Vdc, IC = 0, 100 kHz f 1.0MHz Cibo 60 pF SAFE OPERATION AREA DC Tests TC = 25C, 1cycle, t = 10ms Test 1 VCE = 10Vdc 2N3019, 2N3019S IC = 500mAdc 2N3057A, 2N3700, 2N3700UB IC = 180mAdc Test 2 VCE = 40Vdc 2N3019, 2N3019S IC = 125mAdc 2N3057A, 2N3700, 2N3700UB IC = 45mAdc Test 3 VCE = 80Vdc 2N3019, 2N3019S IC = 60mAdc 2N3057A, 2N3700, 2N3700UB IC = 22.5mAdc (1) Pulse Test: Pulse Width = 300s, Duty Cycle 2.0% T4-LDS-0185 Rev. 1 (101726) Page 2 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS Symbol TO-39 TO-5 CD CH HD LC LD LL LU L1 L2 Q TL TW r P Dimensions Inches Millimeters Min Max Min Max .305 .335 7.75 8.51 .240 .260 6.10 6.60 .335 .370 8.51 9.40 .200 TP 5.08 TP .016 .021 0.41 0.53 .500 .750 12.70 19.05 .016 .019 0.41 0.48 .050 1.27 .250 6.35 .050 1.27 .029 .045 0.74 1.14 .028 .034 0.71 0.86 .010 0.25 45 TP 45 TP .100 2.54 Notes 6 7, 8 7, 8, 12 7, 8 7, 8 7, 8 5 4 3 10 6 NOTES: 1. Dimension are in inches. 2. Millimeters are given for general information only. 3. Beyond r (radius) maximum, TW shall be held for a minimum length of .011 (0.28 mm). 4. Dimension TL measured from maximum HD. 5. Body contour optional within zone defined by HD, CD, and Q. 6. Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. The device may be measured by direct methods. 7. Dimension LU applies between L1 and L2. Dimension LD applies between L2 and minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 8. All three leads. 9. The collector shall be internally connected to the case. 10. Dimension r (radius) applies to both inside corners of tab. 11. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. 12. For "S" suffix devices, dimension LL is 0.500 (12.70 mm) minimum, 0.750 (19.05 mm) maximum. 13. "S" suffix devices, dimension LL is 0.50 (12.70 mm) minimum, 0.75 (19.05 mm) maximum. 14. "L" suffix devices, dimension LL is 1.500 (38.10 mm) minimum, 1.750 (44.45 mm) maximum. 13. 15. Lead 1 = emitter, lead 2 = base, lead 3 = collector. FIGURE 1. Physical dimensions for device types 2N3019 (TO-5) and 2N3019S (TO-39). T4-LDS-0185 Rev. 1 (101726) Page 3 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Symbol CD CH HD LC LD LL LU L1 L2 TL TW r Dimensions Inches Millimeters Min Max Min Max .178 .195 4.52 4.95 .065 .085 1.65 2.16 .209 .230 5.31 5.84 .100 TP 2.54 TP .016 .021 0.41 0.53 .500 1.750 12.70 44.45 .016 .019 0.41 0.48 .050 1.27 .250 6.35 .028 .048 0.71 1.22 .036 .046 0.91 1.17 .007 0.18 45 TP 45 TP Note 6 7 7 7 7 7 3 2 10, 11 6 NOTES: 1. Dimension are in inches. 2. Millimeters are given for general information only. 3. Beyond r (radius) maximum, TW shall be held for a minimum length of .011 inch (0.28 mm). 4. Dimension TL measured from maximum HD. 5. Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. The device may be measured by direct methods. 6. Dimension LU applies between L1 and L2. Dimension LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 7. All three leads. 8. The collector shall be internally connected to the case. 9. Dimension r (radius) applies to both inside corners of tab. 10. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. 11. Lead 1 = emitter, lead 2 = base, lead 3 = collector. FIGURE 2. Physical dimensions for 2N3057A (TO-46). T4-LDS-0185 Rev. 1 (101726) Page 4 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Symbol CD CH HD LC LD LL LU L1 L2 P Q TL TW r Dimensions Inches Millimeters Min Max Min Max .178 .195 4.52 4.95 .170 .210 4.32 5.33 .209 .230 5.31 5.84 .100 TP 2.54 TP .016 .021 0.41 0.53 .500 .750 12.70 19.05 .016 .019 0.41 0.48 .050 1.27 .250 6.35 .100 2.54 .030 0.76 .028 .048 0.71 1.22 .036 .046 0.91 1.17 .010 0.25 45 TP 45 TP 1, 2, 9, 11, 12 Note 6 7,8 7,8 7,8 7,8 7,8 5 3,4 3 10 6 NOTES: 1. Dimension are in inches. 2. Millimeters are given for general information only. 3. Beyond r (radius) maximum, TH shall be held for a minimum length of .011 inch (0.28 mm). 4. Dimension TL measured from maximum HD. 5. Body contour optional within zone defined by HD, CD, and Q. 6. Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. The device may be measured by direct methods or by the gauge and gauging procedure shown in figure 2. 7. Dimension LU applies between L1 and L2. Dimension LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 8. All three leads. 9. The collector shall be internally connected to the case. 10. Dimension r (radius) applies to both inside corners of tab. 11. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. 12. Lead 1 = emitter, lead 2 = base, lead 3 = collector. FIGURE 3. Physical dimensions for type 2N3700 (TO-18). T4-LDS-0185 Rev. 1 (101726) Page 5 of 6 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Symbol BH BL BW CL CW LL1 LL2 Dimensions Inches Millimeters Min Max Min Max .046 .056 1.17 1.42 .115 .128 2.92 3.25 .085 .108 2.16 2.74 .128 3.25 .108 2.74 .022 .038 0.56 0.96 .017 .035 0.43 0.89 Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Note Symbol LS1 LS2 LW r r1 r2 Dimensions Inches Millimeters Min Max Min Max .035 .039 0.89 0.99 .071 .079 1.80 2.01 .016 .024 0.41 0.61 .008 0.20 .012 0.31 .022 0.56 Note NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Hatched areas on package denote metallized areas. 4. Pad 1 = Base, Pad 2 = Emitter, Pad 3 = Collector, Pad 4 = Shielding connected to the lid. 5. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. FIGURE 4. Physical dimensions, surface mount (2N3700UB). T4-LDS-0185 Rev. 1 (101726) Page 6 of 6