Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC372LP3 / 372LP3E v03.0610 AMPLIFIERS - LOW NOISE - SMT 7 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 700 - 1000 MHz Typical Applications Features The HMC372LP3 / HMC372LP3E is ideal for basestation receivers: Noise Figure: < 1 dB * GSM, GPRS & EDGE Gain: 15 dB * CDMA & W-CDMA Very Stable Gain vs. Supply & Temperature * Private Land Mobile Radio Single Supply: +5V @ 100 mA Output IP3: +34 dBm 50 Ohm Matched Output Functional Diagram General Description The HMC372LP3 & HMC372LP3E are GaAs PHEMT MMIC Low Noise Amplifiers that are ideal for GSM & CDMA cellular basestation front-end receivers operating between 700 and 1000 MHz. The amplifier has been optimized to provide 1 dB noise figure, 15 dB gain and +34 dBm output IP3 from a single supply of +5V @ 100 mA. Input and output return losses are 25 and 14 dB respectively with the LNA requiring only four external components to optimize the RF Input match, RF ground and DC bias. For applications which require improved noise figure, please see the HMC617LP3(E). Electrical Specifi cations, TA = +25 C, Vs = +5V Parameter Min. Frequency Range Gain 12.5 Gain Variation Over Temperature Max. Min. Typ. Max. 700 - 1000 14.5 11.5 Units MHz 14.5 dB 0.008 0.015 0.008 0.015 Noise Figure 1.0 1.3 1.0 1.3 Input Return Loss 25 25 dB Output Return Loss 14 12 dB Reverse Isolation Output Power for 1dB Compression (P1dB) Saturated Output Power (Psat) 7 - 52 Typ. 810 - 960 20 18 21 17 23.5 Output Third Order Intercept (IP3) (-20 dBm Input Power per tone, 1 MHz tone spacing) 34 Supply Current (Idd) 100 30 dB / C dB 22 dB 20 dBm 22.5 dBm 33 dBm 100 mA For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC372LP3 / 372LP3E v03.0610 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 700 - 1000 MHz 1.2 21 1.1 20 1 19 0.9 GAIN (dB) & P1dB (dBm) RESPONSE (dB) 5 S21 S11 S22 0 -5 -10 -15 -20 -25 0.6 15 0.5 0.4 -35 13 -40 12 4.5 0.75 1 1.25 1.5 FREQUENCY (GHz) 1.75 2 Noise Figure 0.2 4.75 5 5.25 5.5 Noise Figure vs. Temperature 1.5 20 19 1.4 18 1.3 NOISE FIGURE (dB) + 25 C + 85 C - 40 C 17 16 15 14 13 1.2 1.1 1 0.9 0.8 12 0.7 11 0.6 10 + 25 C + 85 C - 40 C 0.5 0.75 0.8 0.85 0.9 FREQUENCY (GHz) 0.95 0.7 1 0.75 0.8 0.85 0.9 FREQUENCY (GHz) 0.95 1 0.95 1 Noise Figure vs. Vdd Gain vs. Vdd 1.5 20 19 1.4 18 1.3 NOISE FIGURE (dB) + 4.5 V + 5.0 V + 5.5 V 17 16 15 14 13 1.1 1 0.9 0.8 0.7 11 0.6 10 + 4.5 V + 5.0 V + 5.5 V 1.2 12 0.7 0.3 VOLTAGE SUPPLY (Vdd) Gain vs. Temperature 0.7 0.7 16 -30 0.5 0.8 Gain P1dB 17 14 0.25 GAIN (dB) 18 AMPLIFIERS - LOW NOISE - SMT 22 15 NOISE FIGURE (dB) 20 10 GAIN (dB) 7 Gain, Noise Figure & Power vs. Supply Voltage @ 850MHz Broadband Gain & Return Loss 0.5 0.75 0.8 0.85 0.9 FREQUENCY (GHz) 0.95 1 0.7 0.75 0.8 0.85 0.9 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 - 53 HMC372LP3 / 372LP3E v03.0610 Input Return Loss vs. Temperature Output Return Loss vs. Temperature 0 0 -5 -2 -10 RETURN LOSS (dB) RETURN LOSS (dB) -4 + 25 C + 85 C - 40 C -15 -20 -25 -30 -6 +25 C +85 C -40 C -8 -10 -12 -14 -16 -35 -18 -20 -40 0.7 0.75 0.8 0.85 0.9 FREQUENCY (GHz) 0.95 1 Output IP3 vs. Temperature 0.7 COMPRESSION POINT (dBm) 38 + 25 C + 85 C - 40 C 37 36 35 34 33 32 31 0.95 1 0.95 1 23 PSAT 22 21 20 P1dB 19 +25 C +85 C -40 C 18 17 15 0.75 0.8 0.85 0.9 0.95 1 0.7 0.75 0.8 0.85 0.9 FREQUENCY (GHz) P1dB vs. Vdd 40 25 39 24 38 23 + 4.5 V + 5.0 V + 5.5 V 37 22 P1dB (dBm) OUTPUT IP3 (dBm) 1 16 Output IP3 vs. Vdd 36 35 34 21 20 19 33 18 32 17 31 16 30 7 - 54 0.95 24 FREQUENCY (GHz) 0.7 0.8 0.85 0.9 FREQUENCY (GHz) 25 39 30 0.7 0.75 P1dB & Psat vs. Temperature 40 OUTPUT IP3 (dBm) AMPLIFIERS - LOW NOISE - SMT 7 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 700 - 1000 MHz + 4.5 V + 5.0 V + 5.5 V 15 0.75 0.8 0.85 0.9 FREQUENCY (GHz) 0.95 1 0.7 0.75 0.8 0.85 0.9 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC372LP3 / 372LP3E v03.0610 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 700 - 1000 MHz Output IP3 vs. Input Power @ 950 MHz 39 1 MHz Tone Separation 6 MHz Tone Separation -5 ISOLATION (dB) 38 37 36 35 34 +25 C +85 C -40 C -10 -15 -20 33 32 -25 31 -30 30 -20 -15 -10 -5 INPUT POWER PER TONE (dBM) Absolute Maximum Ratings 0 0.7 0.75 0.8 0.85 0.9 FREQUENCY (GHz) 0.95 Typical Supply Current vs. Vdd +8.0 Vdc Vdd (Vdc) RF Input Power (RFIN)(Vs = +5.0 Vdc) +15 dBm +4.5 98 Channel Temperature 150 C +5.0 100 Continuous Pdiss (T = 85 C) (derate 15.6 mW/C above 85 C) 1.015 W +5.5 102 Thermal Resistance (channel to ground paddle) 64.1 C/W Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C Drain Bias Voltage (Vdd) 1 Idd (mA) AMPLIFIERS - LOW NOISE - SMT 0 40 OUTPUT IP3 (dBm) 7 Reverse Isolation vs. Temperature ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 - 55 HMC372LP3 / 372LP3E v03.0610 Outline Drawing AMPLIFIERS - LOW NOISE - SMT 7 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 700 - 1000 MHz NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC372LP3 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC372LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H372 XXXX [2] H372 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX 7 - 56 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC372LP3 / 372LP3E v03.0610 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 700 - 1000 MHz Pin Number Function Description 1, 5, 8, 9 N/C No connection necessary. These pins may be connected to RF/DC ground. 2, 4, 6, 10, 12, 13, 14, 16 GND These pins must be connected to RF/DC ground. 3 RF IN This pin is matched to 50 Ohms with a 22 nH inductor to ground. See Application Circuit. ACG AC Ground - An external capacitor of 0.01F to ground is required for low frequency bypassing. See Application Circuit for further details. Vdd Power supply voltage. Choke inductor and bypass capacitor are required. See application circuit. RF OUT This pin is AC coupled and matched to 50 Ohms. Interface Schematic 7, 15 11 Application Circuit AMPLIFIERS - LOW NOISE - SMT 7 Pin Descriptions Note 1: Choose value of capacitor C1 for low frequency bypassing. A 0.01 F 10% capacitor is recommended. Note 2: L1, L2 and C1 should be located as close to the pins as possible. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 - 57 HMC372LP3 / 372LP3E v03.0610 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 700 - 1000 MHz Evaluation PCB AMPLIFIERS - LOW NOISE - SMT 7 List of Materials for Evaluation PCB 106821 [1] Item Description J1 - J2 PCB Mount SMA RF Connector J3 - J4 DC Pin C1 10000 pF Capacitor, 0402 Pkg. C2 10000 pF Capacitor, 0060 Pkg. L1 22nH Inductor, 0402 Pkg. L2 18nH Inductor, 0603 Pkg. U1 HMC372LP3 / HMC372LP3E Amplifier PCB [2] 106722 Evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 7 - 58 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC372LP3 / 372LP3E v03.0610 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 700 - 1000 MHz 7 AMPLIFIERS - LOW NOISE - SMT Notes: For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 - 59 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC372LP3ETR HMC372LP3E 106821-HMC372LP3