Smart Low Side Power Switch Power HITFET BTS 142D Features Product Summary * Logic Level Input Drain source voltage VDS 42 V * Input Protection (ESD) On-state resistance RDS(on) 28 mW * Thermal shutdown with auto restart Nominal load current ID(Nom) 4.6 A * Green product (RoHS compliant) Clamping energy EAS 3.5 J * Overload protection * Short circuit protection * Overvoltage protection * Current limitation P / PG-TO252-3-11 * Analog driving possible Application * All kinds of resistive, inductive and capacitive loads in switching or linear applications * C compatible power switch for 12 V DC applications * Replaces electromechanical relays and discrete circuits General Description N channel vertical power FET in Smart SIPMOS O technology. Fully protected by embedded protection functions. Vbb M HITFET a Drain Current Limitation In Pin 2 and 4 (TAB) OvervoltageProtection Gate-Driving Unit Pin 1 ESD Overload Protection Overtemperature Protection Short circuit Protection Pin 3 Source Complete product spectrum and additional information http://www.infineon.com/hitfet Datasheet 1 Rev. 1.3, 2006-12-22 Smart Low Side Power Switch Power HITFET BTS 142D Maximum Ratings at Tj = 25C, unless otherwise specified Parameter Symbol Drain source voltage VDS 42 Supply voltage for full short circuit protection Vbb(SC) 42 Continuous input voltage1) VIN Continuous input current2) IIN -0.2V VIN 10V Value Unit V -0.2 2) ... +10 mA self limited VIN < -0.2V or VIN > 10V | IIN | 2 Operating temperature Tj -40 ...+150 Storage temperature Tstg -55 ... +150 Power dissipation 5) Ptot C W TC = 85 C 59 6cm 2 cooling area , TA = 85 C 1.1 Unclamped single pulse inductive energy 2) EAS 3.5 J Load dump protection VLoadDump2)3) = VA + VS VIN = 0 and 10 V, t d = 400 ms, RI = 2 W, VLD 67.5 V 2 kV RL = 3 W, VA = 13.5 V Electrostatic discharge voltage2) (Human Body Model) VESD according to Jedec norm EIA/JESD22-A114-B, Section 4 Thermal resistance junction - case: R thJC SMD: junction - ambient R thJA 1.1 K/W @ min. footprint 115 @ 6 cm 2 cooling area 4) 55 1For input voltages beyond these limits I has to be limited. IN 2not subject to production test, specified by design 3V Loaddump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 4 Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70m thick) copper area for drain connection. PCB mounted vertical without blown air. 5not subject to production test, calculated by R thJA and Rds(on) Datasheet 2 Rev. 1.3, 2006-12-22 Smart Low Side Power Switch Power HITFET BTS 142D Electrical Characteristics Parameter Symbol at Tj = 25C, unless otherwise specified Characteristics VDS(AZ) Drain source clamp voltage Values Unit min. typ. max. 42 - 55 V Tj = - 40 ...+ 150 C, ID = 10 mA IDSS Off-state drain current Tj = -40...+85 C, V DS = 32 V, VIN = 0 V Tj = 150 C A - 1.5 8 - 10 20 VIN(th) Input threshold voltage ID = 2.4 mA, T j = 25 C ID = 2.4 mA, T j = 150 C On state input current IIN(on) On-state resistance R DS(on) V 1.3 1.7 2.2 0.8 - - - 10 30 A mW VIN = 5 V, ID = 4.6 A, Tj = 25 C - 27 34 VIN = 5 V, ID = 4.6 A, Tj = 150 C - 54 68 - 23 28 - 46 56 R DS(on) On-state resistance VIN = 10 V, I D = 4.6 A, T j = 25 C VIN = 10 V, I D = 4.6 A, T j = 150 C Nominal load current 5) ID(Nom) 4.6 5.5 - Tj < 150C, V IN = 10 V, TA = 85 C, SMD 1) Nominal load current 5) ID(ISO) 12.6 15.3 - VIN = 10 V, VDS = 0.5 V, TC = 85 C, Tj < 150C Current limit (active if VDS>2.5 V)2) ID(lim) 30 45 55 A VIN = 10 V, VDS = 12 V, t m = 200 s 1@ 6 cm2 cooling area 2Device switched on into existing short circuit (see diagram Determination of I D(lim) ). If the device is in on conditi and a short circuit occurs, these values might be exceeded for max. 50 s. 5not subject to production test, calculated by R thJA and Rds(on) Datasheet 3 Rev. 1.3, 2006-12-22 Smart Low Side Power Switch Power HITFET BTS 142D Electrical Characteristics Parameter Symbol at Tj = 25C, unless otherwise specified Values Unit min. typ. max. ton - 60 120 toff - 60 120 -dVDS/dt on - 0.3 1.5 dVDS/dtoff - 0.3 1.5 150 175 - C K Dynamic Characteristics Turn-on time VIN to 90% ID : s RL = 4.7 W, VIN = 0 to 10 V, Vbb = 12 V VIN to 10% ID: RL = 4.7 W, VIN = 10 to 0 V, Vbb = 12 V Slew rate on 70 to 50% Vbb: Turn-off time RL = 4.7 W, VIN = 0 to 10 V, Vbb = 12 V Slew rate off 50 to 70% Vbb: V/s RL = 4.7 W, VIN = 10 to 0 V, Vbb = 12 V Protection Functions1) Thermal overload trip temperature Tjt Thermal hysteresis 2) DT jt - 10 - Input current protection mode IIN(Prot) - 180 400 EAS 3.5 - - J VSD - 1.0 1.5 V A Tj = 150 C Unclamped single pulse inductive energy 2) ID = 4.6 A, Tj = 25 C, Vbb = 12 V Inverse Diode Inverse diode forward voltage IF = 51 A, tm = 250 s, V IN = 0 V, tP = 300 s 1Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are not designed for continuous repetitive operation. 2not subject to production test, specified by design Datasheet 4 Rev. 1.3, 2006-12-22 Smart Low Side Power Switch Power HITFET BTS 142D Block diagram Inductive and overvoltage output clamp Terms RL V 2 I IN 1 D Z D IN ID VDS Vbb HITFET S S 3 VIN HITFET Short circuit behaviour Input circuit (ESD protection) Gate Drive Input VIN Source/ Ground IIN IDS Tj Datasheet 5 Rev. 1.3, 2006-12-22 Smart Low Side Power Switch Power HITFET BTS 142D 1 Maximum allowable power dissipation 2 On-state resistance Ptot = f(TC) resp. R ON = f(Tj ); ID=12.6A; VIN =10V Ptot = f(TA) @ R thJA=55 K/W 5 60 max. W mW Rthjc = 1.1 K/W RDS(on) 4 Ptot 3.5 3 2.5 40 typ. 30 2 SMD @ 6cm2 20 1.5 1 10 0.5 0 -50 -25 0 25 50 75 100 C 0 -50 150 -25 0 25 50 75 100 125 C TA;TC 3 On-state resistance 4 Typ. input threshold voltage R ON = f(T j); ID= 12.6A; V IN=5V VIN(th) = f(Tj); ID = 1.2 mA; V DS = 12V 70 175 Tj 2 max. V mW 50 VGS(th) RDS(on) 1.6 typ. 40 1.4 1.2 1 30 0.8 0.6 20 0.4 10 0.2 0 -50 -25 0 25 50 75 100 125 C 0 -50 175 Tj Datasheet -25 0 25 50 75 100 C 150 Tj 6 Rev. 1.3, 2006-12-22 Smart Low Side Power Switch Power HITFET BTS 142D 5 Typ. transfer characteristics 6 Typ. short circuit current I D=f(V IN); VDS=12V; T Jstart=25C ID(lim) = f(Tj); VDS=12V Parameter: V IN 50 60 A A 50 40 45 35 ID ID 40 30 35 25 30 Vin=10V 20 25 5V 20 15 15 10 10 5 0 1 5 2 3 4 5 6 7 V 8 0 -50 10 -25 0 25 50 75 VIN 100 125 C 175 Tj 7 Typ. output characteristics 8 Off-state drain current I D=f(V DS); T Jstart=25C Parameter: V IN IDSS = f(T j) 60 25 A A 50 10V 45 7V max. 20 IDSS 6V 40 ID 5V 35 4V 30 17.5 15 12.5 25 10 20 typ. 7.5 15 Vin=3V 5 10 2.5 5 0 0 1 2 3 4 V 0 -50 6 VDS Datasheet -25 0 25 50 75 100 125 C 175 Tj 7 Rev. 1.3, 2006-12-22 Smart Low Side Power Switch Power HITFET BTS 142D 9 Typ. overload current 10 Typ. transient thermal impedance ID(lim) = f(t), Vbb=12 V, no heatsink Parameter: Tjstart ZthJA=f(tp) @ 6 cm2 cooling area Parameter: D=tp/T 10 70 2 K/W A D=0.5 -40C 10 1 0.2 25C ZthJA ID(lim) 0.1 50 40 85C 30 150C 0.05 10 0 0.02 0.01 10 -1 10 -2 10 -3 20 Single pulse 10 0 0 0.5 1 1.5 2 2.5 3 3.5 ms 4 5 10 -7 10 -6 10 -5 10 -4 10 -3 10 -2 10 -1 10 0 10 1 s 10 3 tp t 11 Determination of ID(lim) ID(lim) = f(t); t m = 200s Parameter: TJstart 70 A ID(lim) -40C 50 25C 40 85C 30 150C 20 10 0 0 0.1 0.2 0.3 0.4 ms 0.6 t Datasheet 8 Rev. 1.3, 2006-12-22 Smart Low Side Power Switch Power HITFET BTS 142D Package Outlines Package Outlines 6.5 +0.15 -0.05 A 0.15 MAX. per side B (5) 0.5 +0.08 -0.04 0.9 +0.20 -0.01 0...0.15 0.8 0.15 (4.24) 1 0.1 9.98 0.5 6.22 -0.2 5.4 0.1 2.3 +0.05 -0.10 0.51 MIN. 1 3x 0.75 0.1 0.5 +0.08 -0.04 2.28 4.57 0.1 B 0.25 M A B All metal surfaces tin plated, except area of cut. GPT09277 Figure 1 PG-TO252-3-11 (Plastic Dual Small Outline Package) (RoHS-Compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pbfree finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). Please specify the package needed (e.g. green package) when placing an order You can find all of our packages, sorts of packing and others in our Infineon Internet Page "Products": http://www.infineon.com/products. Datasheet 9 Dimensions in mm Rev. 1.3, 2006-12-22 Smart Low Side Power Switch Power HITFET BTS 142D Revision History 2 Revision History Version Rev. 1.3 Date Changes 2006-12-22 released automotive green and robust version (BTS) Package parameter (humidity and climatic) removed in Maximum ratings Rev. 1.2 2006-12-11 AEC icon added RoHS icon added Green product (RoHS-compliant) added to the feature list Package information updated to green Green explanation added Rev. 1.1 2006-08-08 released non automotive green version (ITS) Rev. 1.0 2004-03-05 released production version Datasheet 10 Rev. 1.3, 2006-12-22 Edition 2006-12-22 Published by Infineon Technologies AG 81726 Munich, Germany (c) Infineon Technologies AG 2007. All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.