Amplifier for infrared detector C4159/C5185 series C3757-02 Low noise amplifiers for infrared detector (InSb, InAs, InAsSb, InGaAs, MCT, PbS, PbSe) Accessories Instruction manual Power cable (one end with 4-pin connector for connection to amplifier and the other end unterminated, 2 m) A4372-02 Required power supply specifications * * * * * C4159 series: 15 V 0.5 C5185 series: 15 V 0.5 Current-carrying capacity: 1.5 times or more of amplifier's maximum current consumption Ripple noise: 5 mVp-p or less Analog power supply only Recommended DC power supply: E3620A, E3630A (Agilent Technologies) Absolute maximum ratings (Ta=25 C) Parameter Supply voltage Operating temperature Storage temperature Value 18.0 max. 0 to +40 -20 to +70 Unit V C C Note: Absolute maximum ratings are the values that must not be exceeded at any time. If even one of the absolute maximum ratings is exceeded even for a moment, the product quality may be impaired. Always be sure to use the product within the absolute maximum ratings. Amplifiers for photovoltaic detectors (Typ.) Parameter Applicable detector *1 *2 *3 Conversion impedance Frequency response (amp only, -3 dB) Output impedance Maximum output voltage (1 k load) Output offset voltage Equivalent input noise current (f=1 kHz) Reverse voltage External power supply *5 Current consumption C4159-01 C4159-04 C4159-05 C4159-06 Dewar type InSb (P5968-060, P5968-100) Dewar type InSb Dewar type InAs InAs Dewar type InAsSb (P5968-200) (P7163) (P10090 series) (P11120-901) 108, 107, 106 106, 105, 104 2 x 107, 2 x 106, 2 x 105 108, 107, 106 (3 ranges switchable) (3 ranges switchable) (3 ranges switchable) (3 ranges switchable) Unit V/A DC to 100 kHz *4 DC to 45 kHz DC to 15 kHz DC to 100 kHz - 50 50 50 50 +10 +10 +10 +10 V 5 0.15 (108, 107 range) 0.65 (106 range) 5 5 mV 6 pA/Hz1/2 +30, -22 max. V mA 10 0.15 (108, 107 range) 0.55 0.65 (106 range) Limited to 0 V operation 15 +30, -10 max. These amplifiers cannot operate multiple detectors. Consult us before purchasing if you want to use with a detector other than listed here. Consult us before purchasing if you want to use with a multi-element detector. When connected to a detector, frequency response becomes 60 kHz or less depending on the detector active area. (0.6 mm: 60 kHz or less, 1 mm: 25 kHz or less) Ringing occurs in the output if the rise time tr (0 to 90%) of incident light is approximately 100 s or less. The ringing becomes larger as the rise time becomes shorter. No ringing occurs when detecting sine-wave light. (For information on the ringing specifications, see page 2.) *5: Recommended DC power supply (analog power supply): 15 V Current capacity: More than 1.5 times the maximum current consumption Ripple noise: 5 mVp-p or less Note: Output noise voltage = Equivalent input noise current x Conversion impedance For information about accessories except for the amplifiers, refer to our datasheet "Infrared detector accessories". *1: *2: *3: *4: www.hamamatsu.com 1 Amplifier for infrared detector C4159/C5185 series, C3757-02 Ringing Vri Ringing specifications 5V 90 % 10 % tr Incident light Output waveform when tr = 40 s and active area is 0.6 mm Ringing Vri 1.5 V Oscillating cycle 3 cycles KIRDC0090EA Amplifier for InGaAs PIN photodiodes (Typ.) Parameter Applicable detector *6 *7 Conversion impedance Frequency response (amp only, -3 dB) Output impedance Maximum output voltage (1 k load) Output offset voltage Equivalent input noise current (f=1 kHz) Reverse voltage External power supply *8 Current consumption C4159-03 InGaAs 107, 106, 105 (3 ranges switchable) Unit - DC to 15 kHz - 50 +10 V 5 mV 2.5 pA/Hz1/2 Can be applied from external unit 15 15 max. V mA V/A Amplifier for photoconductive detectors (Typ.) *9 Parameter 6 7 Applicable detector * * * 10 Input impedance Voltage gain Frequency response (amp only, -3 dB) Detector bias current Output impedance Maximum output voltage (1 k load) Equivalent input noise voltage (f=1 kHz) External power supply *8 Current consumption C5185-02 Dewar type MCT, InSb (P6606 series) 5 66 (x 2000) C5185-03 MCT (P3981/P2750 series) *11 5 66 (x 2000) C3757-02 Unit PbS, PbSe - 10000 40 (x 100) k dB 0.2 Hz to 10 kHz - Internal bias - 50 5 Hz to 250 kHz 5 Hz to 250 kHz 5 mA, 10 mA, 15 mA (3 ranges switchable) 50 0.1 mA, 0.5 mA, 1 mA (3 ranges switchable) 50 10 10 10 V 2.6 1.8 40 nV/Hz1/2 15 +100, -30 max. 15 +100, -30 max. 15 +15, -15 max. V mA Note: Output noise voltage = Equivalent input noise voltage x Voltage gain *6: These amplifiers cannot operate multiple detectors. *7: Consult us before purchasing if you want to use with a detector other than listed here. *8: Recommended DC power supply (analog power supply): 15 V Current capacity: More than 1.5 times the maximum current consumption Ripple noise: 5 mVp-p or less *9: Before purchasing, make sure the bias current to the detector matches the detector bias current specified in the above table. *10: Consult us before purchasing if you want to use with a multi-element detector. *11: Preamp for P3257-25/-30/-31 available upon request 2 Amplifier for infrared detector C4159/C5185 series, C3757-02 Dimensional outline (unit: mm, tolerance unless otherwise noted: 1) OUT 24.5 30 PREAMPLIFIER POWER HIGH MID LOW IN 39.5 IN 60 HIGH MID LOW 39.5 24.5 12.5 25 PREAMPLIFIER POWER 60 37 4-pin connector 11.5 4-pin connector C5185-02/-03 11.5 C4159-01/-03/-04/-05/-06 OUT BNC Bias adjusting screw Gain adjusting screw Offset voltage adjusting screw BNC connector BNC connector 85 18 30 18 26.2 23 15 23 35 21.2 85 KIRDA0048EB Solder leads to these terminals. PIN connections GND Cathode Anode Note: Socket for lead attachment is not provided. KIRDA0046EC C3757-02 OUT 38.5 60 IN 13.5 PREAMPLIFIER POWER 25 37 12.5 4-pin connector BNC connector 18 18 12 30 85 Solder leads to these terminals. PIN connections GND Detector Detector Note: Socket for lead attachment is not provided. KIRDA0049EC 3 Amplifier for infrared detector C4159/C5185 series, C3757-02 A4372-02 2000 100 70 10 4.8 27 11 1.1 10 3 Shielded wire (4 conductors) Solder processing Connector: HR10-7P-4P (made by Hirose Electric) Pin no. Pin connection Lead color -Vs Blue GND Black/white/blue stranded wire GND +Vs White As viewed from connector side KIRDA0196EB The C4159-03, C5185-02/-03 and C3757-02 conform to the European EMC directives (Applied standard: EN 61326-1 Class B). Information described in this material is current as of December, 2011. Product specifications are subject to change without prior notice due to improvements or other reasons. Before assembly into final products, please contact us for the delivery specification sheet to check the latest information. Type numbers of products listed in the delivery specification sheets or supplied as samples may have a suffix "(X)" which means preliminary specifications or a suffix "(Z)" which means developmental specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvagen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1 int. 6, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 China: Hamamatsu Photonics (China) Co., Ltd.: 1201 Tower B, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866 Cat. No. KIRD1011E13 Dec. 2011 DN 4