CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 1 of 33 DATE 07.01.2012 Product Specification Applicant / Manufacturer Panasonic Industrial Devices Europe GmbH Hardware Zeppelinstrasse 19 21337 Luneburg Germany Applicant / Manufacturer TOSHIBA Electronics Europe GmbH Software Hansaallee 181 40549 Dusseldorf Germany Software Version Please refer to chapter 20 / 21 By purchase of any of products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required without notification. Power Electronics R&D Center Wireless Connectivity Panasonic Industrial Devices Europe GmbH APPROVED genehmigt CHECKED gepruft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 2 of 33 DATE 07.01.2012 TABLE OF CONTENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Scope of this Document .................................................................................................. 4 Key Features................................................................................................................... 4 Bluetooth Low Energy ..................................................................................................... 5 Applications for the Module............................................................................................. 5 Description for the Module .............................................................................................. 5 Detailed Description ........................................................................................................ 6 6.1 PAN1026 Terminal Layout..................................................................................... 6 6.2 PAN1026 Terminal Description ............................................................................. 7 Bluetooth Features........................................................................................................ 10 Block Diagram............................................................................................................... 10 Test Conditions ............................................................................................................. 11 General Device Requirements and Operation .............................................................. 11 10.1 Absolute Maximum Ratings ................................................................................. 11 10.2 Recommended Operating Conditions.................................................................. 11 10.3 Current Consumption........................................................................................... 12 Bluetooth RF Performance............................................................................................ 13 11.1 Bluetooth Characteristics..................................................................................... 13 Soldering Temperature-Time Profile (for reflow soldering) ........................................... 14 12.1 For lead solder..................................................................................................... 14 12.2 For leadfree solder............................................................................................... 14 Module Dimension ........................................................................................................ 15 PAN1026 FootPrint of the Module ................................................................................ 16 Case Marking ................................................................................................................ 17 15.1 Example for Marking............................................................................................ 17 15.2 Marking Definition ................................................................................................ 17 Mechanical Requirements............................................................................................. 17 Reliability Tests ............................................................................................................. 18 Cautions ........................................................................................................................ 18 18.1 Design Notes ....................................................................................................... 18 18.2 Installation Notes ................................................................................................. 19 18.3 Usage Conditions Notes ...................................................................................... 19 18.4 Storage Notes...................................................................................................... 20 18.5 Safety Cautions ................................................................................................... 20 18.6 Other cautions ..................................................................................................... 20 Packaging ..................................................................................................................... 22 19.1 Tape Dimension................................................................................................... 22 19.2 Packing in Tape ................................................................................................... 22 19.3 Component Direction ........................................................................................... 23 19.4 Reel Dimension ................................................................................................... 23 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT 20 21 22 23 24 25 26 27 28 29 30 31 32 No. DS-1026-2400-102 REV. 0.2 PAGE 3 of 33 DATE 07.01.2012 19.5 Label for Package................................................................................................ 24 19.6 Total Package...................................................................................................... 24 Ordering Information ..................................................................................................... 25 Information regarding Software Versions...................................................................... 25 Software ........................................................................................................................ 26 Software block diagram................................................................................................. 27 RoHS and REACH Declaration..................................................................................... 28 Data Sheet Status ......................................................................................................... 29 History for this Document.............................................................................................. 29 Related Documents....................................................................................................... 29 General Information ...................................................................................................... 30 Regulatory Information.................................................................................................. 30 29.1 FCC Notice .......................................................................................................... 30 29.2 Caution ................................................................................................................ 30 29.3 Labeling Requirements........................................................................................ 31 29.4 Antenna Warning ................................................................................................. 31 29.5 Approved Antenna List ........................................................................................ 31 29.6 RF Exposure PAN1026 ....................................................................................... 31 Industry Canada Certification........................................................................................ 32 30.1 IC Notice .............................................................................................................. 32 30.2 Labeling Requirements........................................................................................ 32 European R&TTE Declaration of Conformity ................................................................ 32 Life Support Policy ........................................................................................................ 33 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 4 of 33 DATE 07.01.2012 1 SCOPE OF THIS DOCUMENT This product specification applies to Panasonic's, Class 2, Bluetooth(R) 1 classic and low energy dual mode module, series number: PAN1026. 2 KEY FEATURES 1 Bluetooth Classic and Low Energy Dual Mode 4.0 Surface mount type 15.6 x 8.7 x 1.8 mm Up to 4.0 dBm Tx power (typical) with transmit power control High sensitivity (-88 dBm typ.) Toshibas TC35661SBG-2xx Bluetooth Dual Mode SPP and GATT profiles inside No external components needed Fast Connection Setup in BLE mode Internal crystal oscillator (26MHz) Integrated shielding to resist EMI Manufactured in conformance with RoHS Bluetooth is a registered trademark of the Bluetooth Special Interest Group. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 5 of 33 DATE 07.01.2012 3 BLUETOOTH LOW ENERGY Bluetooth Low Energy (BLE) is a part of Bluetooth Ver. 4.0, BT 4.0 covers both BLE as well as BT classic 2.1 and 3.0. If both are implemented in one device it is called dual mode. Dual mode chips implement the low energy specification and may consume just a fraction of the power of classic Bluetooth, allowing the short-range wireless standard to extend to coin cell battery applications Dual mode chips combine low energy with the power of classic Bluetooth and are likely to become a de facto feature in almost all new Bluetooth enabled cellular phones,computers or portable communication nodes. Bluetooth Low Energy (BLE) is not backwards compatible with previous Bluetooth classic standards (2.1+EDR or 3.0). Dual mode Bluetooth 4.0 is backwards compatible but is not practical for low power devices but targeted to gateway products 4 APPLICATIONS FOR THE MODULE All Embedded Wireless Applications Access Points Industrial Control Medical Scanners Wireless Sensors Low Power Proximity Smart Phone Access Points Temperature Wellness Sports 5 DESCRIPTION FOR THE MODULE The PAN1026 is a short-range Class 2 BLE dual mode module for implementing Bluetooth functionality into various electronic devices. A block diagram can be found in chapter 8. Available now: Bluetooth 2.1 SPP embedded. Available Q2/13: Bluetooth 2.1 SPP embedded - Bluetooth 4.0 LE GATT/GAP will be available Q2/2013 All HW versions 05 and above will support Bluetooth 2.1 SPP embedded - Bluetooth 4.0 LE GATT/GAP. See chapter 15 about details for case marking. Please contact your local sales office for further details on additional options and services: www.panasonic.com/rfmodules for the US, http://industrial.panasonic.com/eu/i/29606/wireless_modules/wireless_modules.html for EU or write an e-mail to wireless@eu.panasonic.com. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 6 of 33 DATE 07.01.2012 6 DETAILED DESCRIPTION 6.1 PAN1026 TERMINAL LAYOUT Top view, Application PCB PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 REV. 0.2 PAGE 7 of 33 DATE 07.01.2012 1.35 1.2 8.70 mm 1.35 SUBJECT No. DS-1026-2400-102 6.2 PAN1026 TERMINAL DESCRIPTION No Pin Name Pin Type Description A1 GND GPIO Number Ground Pin Connect to Ground A2 NC NC Not connected, leave open A3 Reset Digital Input Reset, active-low A4 VCC Power 2V - 3.6V analog/digital power supply connection A5 VCC Power 2V - 3.6V analog/digital power supply connection A6 VCC Power 2V - 3.6V analog/digital power supply connection A7 GND Ground Pin Connect to Ground A8 NC NC Not Connected A9 GND Ground Pin Connect to Ground A11 GND Ground Pin Connect to Ground A12 GND Ground Pin Connect to Ground B1 NC NC Not connected, leave open B2 BTS GPIO 11 B3 BTA GPIO 10 B4 NC NC Not connected, leave open B5 NC NC Not connected, leave open B6 NC NC Not connected, leave open B7 NC NC Not connected, leave open Not supported Not supported PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No Pin Name B8 B9 C1 CS0X GPIO 17 Not supported C2 BTI GPIO 13 Not supported C3 WIA GPIO 12 Not supported C4 NC C5 NC C6 PCMCLK GPIO 04 C7 FSYNC GPIO 05 C8 C9 D1 CS1X GPIO 18 Not supported DIN GPIO 16 Not supported GPIO1 GPIO 01 D2 D3 GPIO Number No. DS-1026-2400-102 PAGE 8 of 33 DATE 07.01.2012 Pin Type Description NC NC Not connected, leave open NC NC Not connected, leave open NC Not connected, leave open NC Not connected, leave open Digital I/O PCM Clock Digital I/O PCM Syncronisation GND Ground Pin Connect to Ground GND Ground Pin Connect to Ground D4 USB*/GPIO0 D5 NC D6 PCMIN D7 Digital I/O Not supported Digital I/O USB direct is not yet supported by the IC and therefore you can use this pin as normal GPIO0. If USB will be supported in the next revision, pin would be Select USB (Connect to PIN E4) Check also [1] NC Not connected, leave open Digital Input PCM In Not supported GND Ground Pin Connect to Ground D8 GND Ground Pin Connect to Ground D9 ANT RF - Signal Antenna Pin (Not connected for standard version) E1 SDA GPIO 15 Digital I/O I2C Interface (Only Internal) Connect to Testpin E2 SCL GPIO 14 Digital I/O I2C Interface (Only Internal) Connect to Testpin E3 VDD_USB E4 USB* E5 CLKREQ E6 UART RXD GPIO 03 Power GPIO 02 REV. 0.2 USB direct is not yet supported by the IC and therefore put to GND. If USB will be supported in the next revision, connect to VCC. Check also [1] USB direct is not yet supported by the IC and therefore please left open. If USB will be supported in the next revision, pin would be Select USB (Connect to PIN D4). Check also [1] Digital Output Active High once crystal frequency is stable Digital Input UART RXD Digital Output PCM Output E7 PCMOUT E8 GND Ground Pin Connect to Ground E9 GND Ground Pin Connect to Ground F1 GND Ground Pin Connect to Ground F2 EEPROM_WP Digital Input F3 USB_P Digital I/O F4 USB_M Digital I/O Internal EEPROM Write Protect (Active High) USB direct is not yet supported by the IC and therefore put to GND. If USB will be supported in the next revision, pin would be USB Data In/Out Check also [1] USB direct is not yet supported by the IC and therefore put to GND. If USB will be supported in the next revision, pin would be PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No Pin Name GPIO Number Pin Type No. DS-1026-2400-102 REV. 0.2 PAGE 9 of 33 DATE 07.01.2012 Description USB Data In/Out Check also [1] F5 UART CTS Digital Input UART CTS F6 SLEEPCLK Digital Input Input Clock for 32.768KHz F7 UARTTXD Digital Output UART TX F8 UARTRTS Digital Output UART RTS F9 GND Ground Pin Connect to Ground F11 GND Ground Pin Connect to Ground F12 GND Ground Pin Connect to Ground PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 10 of 33 DATE 07.01.2012 7 BLUETOOTH FEATURES Bluetooth 4.0 dual mode technology. Class 2 TX power w/o external PA, improving link robustness. Excellent link budget (up to 91 dB), enabling long-range applications. Embedded SPP- and BLE Gatt profiles 8 BLOCK DIAGRAM PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-1026-2400-102 PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT REV. 0.2 PAGE 11 of 33 DATE 07.01.2012 9 TEST CONDITIONS Measurements shall be made under operating free-air temperature range unless otherwise specified. Temperature Humidity Supply Voltage 25 10C 40 to 85%RH 3.3V 10 GENERAL DEVICE REQUIREMENTS AND OPERATION All specifications are over temperature and process, unless indicated otherwise. 10.1 ABSOLUTE MAXIMUM RATINGS No See 2 Value Unit Ratings Over Operating Free-Air Temperature Range 1 Voltage on any digital pin -0.3 to VDD+0.3 V 2 Operating ambient temperature range -40 to 85 C 3 Storage temperature range -40 to 125 C 4 Bluetooth RF inputs 10 dBm 5 ESD: All pads, according to human-body model, JEDEC STD 22, method A114 According to charged-device model, JEDEC STD 22, method C101 1000 500 V 10.2 RECOMMENDED OPERATING CONDITIONS 2 No Rating Min Typ Max Unit 1 Power supply voltage 1.7 1.8 1.9 V 1 Power supply voltage 2.7 3.3 3.6 V 2 Maximum ambient operating temperature -40 85 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 12 of 33 DATE 07.01.2012 10.3 CURRENT CONSUMPTION The current consumption is dependant on the user scenario and the setup and timing in the low power modes. No Characteristics Condition 1 Idle Current After reset was pulled down. 7.8 mA 2 During Connection Sending 3-DH5 packets. Max. output power. 62 mA 3 During Connection Sending DH5 packets. Max. output power. 62 mA 4 During Connection Sending DH3 packets. Max. output power. 61 mA 5 During Connection Sending DH1 packets. Max. output power. 55 mA PANASONIC INDUSTRIAL DEVICES EUROPE GMBH Min Typ Max Unit www.pideu.panasonic.de CLASSIFICATION No. DS-1026-2400-102 PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT REV. 0.2 PAGE 13 of 33 DATE 07.01.2012 11 BLUETOOTH RF PERFORMANCE 11.1 BLUETOOTH CHARACTERISTICS No Characteristics 1 Operation frequency range 2 Channel spacing BT-Classic/BLE 1/2 MHz 3 Output Power Maximum setting, measured at dual ended 50ohm. 4 dBm 4 Sensitivity -87 dBm No 1 Condition Min Typ 2402 Max 2480 Characteristics Condition Typ Spurious emissions Conducted measurement with a 50- dual-ended load. Complies with EN 300 328, EN 300 440 class 2, FCC CFR47, Part 15 and ARIB STD-T-66 <-30 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH BT Spec Unit MHz Max Unit dBm www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 14 of 33 DATE 07.01.2012 12 SOLDERING TEMPERATURE-TIME PROFILE (FOR REFLOW SOLDERING) 12.1 FOR LEAD SOLDER 10 1s Recommended temp. profile for reflow soldering 30 +20/-10s 235C max. Temp.[C] 220 5C 200C 150 10C 90 30s Time [s] 12.2 FOR LEADFREE SOLDER Our used temp. profile for reflow soldering Temp.[C] 30 +20/-10s 230C -250C max. 220C 150C - 190C 90 30s Time [s] Reflow permissible cycle: 2 Opposite side reflow is prohibited due to module weight. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 15 of 33 DATE 07.01.2012 13 MODULE DIMENSION No. Item Dimension Tolerance 1 Width 8.70 0.20 2 Length 15.60 0.20 3 Height 1.80 0.20 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH Remark With case www.pideu.panasonic.de CLASSIFICATION No. DS-1026-2400-102 PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT REV. 0.2 PAGE 16 of 33 DATE 07.01.2012 14 PAN1026 FOOTPRINT OF THE MODULE All dimensions are in millimeters. The outer dimensions have a tolerance of 0.2mm. Top view, Application PCB 15.6 mm 5.0 1.0 0.6 1.2 2.4 F1 F2 F3 F4 F5 F6 F7 F8 F9 E1 E2 E3 E4 E5 E6 E7 E8 E9 D1 D2 D3 D4 D5 D6 D7 D8 D9 C1 C2 C3 C4 C5 C6 C7 C8 C9 B1 B2 B3 B4 B5 B6 B7 B8 B9 A1 A2 A3 A4 A5 A6 A7 A8 A9 F11 F12 A11 A12 0.6 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION No. DS-1026-2400-102 PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT 15 CASE MARKING 2 REV. 0.2 PAGE 17 of 33 DATE 07.01.2012 No. Remark 1 Marking for Pin 1 (Circle 0,15 mm) 2 2D-Code, for internal usage only and can be change without any notice 3 Marking definition see chapter 15.1 3 1 15.1 EXAMPLE FOR MARKING P E Y F A N Y C N 1 0 2 6 W 8 9 8 3 W W D L L C I D : H W / S W 7 A 3 K F T 7 V P A N 1 0 15.2 MARKING DEFINITION (1) Pin1 marking (2) 2D code (Serial number) (3) Marking: PAN1026 (Model Name), HW/SW (Hardware/Software version) ENW89837A3KF (Part Number, refer to chapter 20 Ordering Information) Lot code (YearYear, WeekWeek, Day, LotLot) ES (Engineering Sample marking) 16 MECHANICAL REQUIREMENTS No. Item 1 Solderability 2 Resistance to soldering heat Limit Condition More than 75% of the soldering area shall be coated by solder It shall be satisfied electrical requirements and not be mechanical damage Reflow soldering with recommendable temperature profile PANASONIC INDUSTRIAL DEVICES EUROPE GMBH See chapter 12.2 www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 18 of 33 DATE 07.01.2012 17 RELIABILITY TESTS The measurement should be done after being exposed to room temperature and humidity for 1 hour. Item Limit Condition 1 Vibration test Electrical parameter should be in specification a) Freq.:10~50Hz,Amplitude:1.5mm a) 20min. / cycle,1hrs. each of XYZ axis b) Freq.:30~100Hz, 6G b) 20min. / cycle,1hrs. each of XYZ axis 2 Shock test the same as above Dropped onto hard wood from height of 50cm for 3 times 3 Heat cycle test the same as above -40C for 30min. and +85C for 30min.; each temperature 300 cycles 4 Moisture test the same as above +60C, 90% RH, 300h 5 Low temp. test the same as above -40C, 300h 6 High temp. test the same as above +85C, 300h No. 18 CAUTIONS Failure to follow the guidelines set forth in this document may result in degrading of the product's functions and damage to the product. 18.1 DESIGN NOTES (1) (2) (3) (4) (5) (6) (7) Follow the conditions written in this specification, especially the control signals of this module. The supply voltage has to be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47uF directly at the module). This product should not be mechanically stressed when installed. Keep this product away from heat. Heat is the major cause of decreasing the life of these products. Avoid assembly and use of the target equipment in conditions where the products' temperature may exceed the maximum tolerance. The supply voltage should not be exceedingly high or reversed. It should not carry noise and/or spikes. Keep this product away from other high frequency circuits. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 19 of 33 DATE 07.01.2012 18.2 INSTALLATION NOTES (1) Reflow soldering is possible twice based on the conditions in chapter 15. Set up the temperature at the soldering portion of this product according to this reflow profile. (2) Carefully position the products so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. (3) Carefully locate these products so that their temperatures will not increase due to the effects of heat generated by neighboring components. (4) If a vinyl-covered wire comes into contact with the products, then the cover will melt and generate toxic gas, damaging the insulation. Never allow contact between the cover and these products to occur. (5) This product should not be mechanically stressed or vibrated when reflowed. (6) If you want to repair your board by hand soldering, please keep the conditions of this chapter. (7) Do not wash this product. (8) Refer to the recommended pattern when designing a board. (9) Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the unit. (10) For more details on LGA (Land Grid Arrey) soldering processes refer to the application note. 18.3 USAGE CONDITIONS NOTES (1) (2) (3) (4) (5) (6) (7) Take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation befor assembly on the final products. Do not use dropped products. Do not touch, damage or soil the pins. Follow the recommended condition ratings about the power supply applied to this product. Electrode peeling strength: Do not add pressure of more than 4.9N when soldered on PCB. Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. These products are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information and communication equipment. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 20 of 33 DATE 07.01.2012 18.4 STORAGE NOTES (1) (2) (3) (4) (5) The module should not be stressed mechanically during storage. Do not store these products in the following conditions or the performance characteristics of the product, such as RF performance will be adversely affected: Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX Storage in direct sunlight Storage in an environment where the temperature may be outside the range of 5C to 35C range, or where the humidity may be outside the 45 to 85% range. Storage of the products for more than one year after the date of delivery Storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. Keep this product away from water, poisonous gas and corrosive gas. This product should not be stressed or shocked when transported. Follow the specification when stacking packed crates (max. 10). 18.5 SAFETY CAUTIONS These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications, without deviation when using the products. These products may shortcircuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, then provide the following failsafe functions, as a minimum. (1) Ensure the safety of the whole system by installing a protection circuit and a protection device. (2) Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a dual fault causing an unsafe status. 18.6 OTHER CAUTIONS (1) (2) (3) (4) (5) This specification sheet is copyrighted. Please do not disclose it to a third party. Please do not use the products for other purposes than those listed. Be sure to provide an appropriate fail-safe function on your product to prevent an additional damage that may be caused by the abnormal function or the failure of the product. This product has been manufactured without any ozone chemical controlled under the Montreal Protocol. These products are not intended for other uses, other than under the special conditions shown below. Before using these products under such special conditions, check their performance and reliability under the said special conditions carefully to determine whether or not they can be used in such a manner. In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash. In direct sunlight, outdoors, or in a dusty environment In an environment where condensation occurs. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT (6) (7) No. DS-1026-2400-102 REV. 0.2 PAGE 21 of 33 DATE 07.01.2012 In an environment with a high concentration of harmful gas (e.g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOX) If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these products with new products because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. When you have any question or uncertainty, contact Panasonic. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 22 of 33 DATE 07.01.2012 19 PACKAGING If the product has mass production status, indicated in chapter 25, we will deliver the module in the package which are described below. 19.1 TAPE DIMENSION 19.2 PACKING IN TAPE Empty spaces in component packed area shall be less than two per reel and those spaces shall not be consecutive. Top cover tape shall not be found on reel holes and shall not stick out from reel. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 23 of 33 DATE 07.01.2012 19.3 COMPONENT DIRECTION 19.4 REEL DIMENSION PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 24 of 33 DATE 07.01.2012 19.5 LABEL FOR PACKAGE The picture shows an example from similar product. 105 mm PAN1315 Customer Code (1T) ENW89818C2JF (1P) Lot code [YYWWDLL] Example from above: YY year printed 08 WW normal calendar week printed 01 D day printed 5 (Friday) L line identifier, if more as one printed 1 L lot identifier per day printed 1 Customer Order Code, if any, otherwise company name will be printed (2P) Panasonic Order Code: ENW89837A3KF (9D) Date code as [YYWW] (Q) Quantity [XXXX], variable max. 1500 (HW/SW) Hardware /Software Release Hardware 01 Indicates the HW revision. Software 01 Indicates the SW revision. 19.6 TOTAL PACKAGE PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 25 of 33 DATE 07.01.2012 20 ORDERING INFORMATION Ordering part number ENW89837A3KF (2) Description MOQ PAN1026 CLASS 2 Bluetooth dual mode Module according BT-4.0. Bluetooth(R) smart ready device 1500 (1) Notes: (1) Abbreviation for Minimum Order Quantity (MOQ). The standard MOQ for mass production is 1500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels. (2) Samples are available on customer demand Available now: Bluetooth 2.1 SPP embedded. Available Q2/13: Bluetooth 2.1 SPP embedded - Bluetooth 4.0 LE GATT/GAP will be available Q2/2013 All HW versions 05 and above will support Bluetooth 2.1 SPP embedded - Bluetooth 4.0 LE GATT/GAP. See chapter 15 about details for case marking. 21 INFORMATION REGARDING SOFTWARE VERSIONS The version number of the embedded software can be read out by an extended HCI command. The extended HCI command class < HCI_M2_Message_Get >" allows the reading of the firmware version. Pls refer to the extended HCI command list of TC35661 LSI. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 26 of 33 DATE 07.01.2012 22 SOFTWARE The module software offers both embedded Bluetooth HCI (Host Control Interface), extended HCI and TCU (Toshiba Control Unit) Command interfaces via the embedded UART interface a) HCI commands are standard according to Bluetooth standard specifications. b) Extended HCI commands are available for device control, such as RF control, BD_ADDR control, firmware version control, embedded IO control, maintenance tasks etc. Please refer to the "Extension HCI Command Document". c) The PAN1026 includes the Bluetooth LSI TC35661 incorporating Bluetooth stack and SPP profile and BLE GATT profile. The profile application interface is described in the "SPP Command Interface Document" (about 14 commands) and the "Bluetooth Basic Management Command Interface Document" (about 46 commands). The related high level commands are called "TCU" commands. The "SPP Message Sequence Chart Document" and the "Bluetooth Management Message Sequence Chart Document" describe the logical and sequential procedure to use those commands. d) After RESET of the module, the module starts in HCI mode. The "Bluetooth LSI TC35661 Application Note" describes how to start the device and enter into "TCU" mode thereafter. e) The LSI Supplier (Toshiba) offers SPP drivers, that allows a further abstraction towards the application software including SPP programming examples. This is documented in the "BT SPP API Specification", the "BT SPP Driver Specification" and the "BT SPP Application Note". The "SPP API" offers a few high-level APIs for LSI initialization, connection setup and communication with a remote SPP device. The user has full control over all LSI features by utilizing the lower-level "SPP Drivers". The drivers take care for issuing commands and data to the LSI and they handle the responses from the TC36661. The "Application Note" includes a SPP programming example and shows the integration with a RTOS." All documents are available on respective Panasonic or Toshiba websites. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 27 of 33 DATE 07.01.2012 23 SOFTWARE BLOCK DIAGRAM PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 28 of 33 DATE 07.01.2012 24 ROHS AND REACH DECLARATION Hereby we declare to our best present knowledge based on declaration of our suppliers that this product follows the latest official RoHS and REACH Directive. For the most updated one, please refer to [5]. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 29 of 33 DATE 07.01.2012 25 DATA SHEET STATUS This data sheet contains the preliminary specification. Panasonic reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Please consult the most recently issued data sheet before initiating or completing a design. Use this URL to search for the most recent version of this data sheet: PAN1026 Datasheet 26 HISTORY FOR THIS DOCUMENT Revision Date Modification / Remarks 0.1 November 2012 1 preliminary version. 0.2 January 2013 Update chapter 24 with the latest declaration. Correct chapter 10.3 with the latest current values measured on the reference design. Made the description for the USB ports in chapter 6.2 more precised. st 27 RELATED DOCUMENTS For an update, please search in the suitable homepage. [1] PAN1026ETU Design-Guide (Release planned Q1/2013) [2] EasySPP Evaluation Software http://pideu.panasonic.de/pdf/185ext.zip [3] Semiconductor Website: http://www.toshiba-components.com/bluetooth/index.html [4] Application Note Land Grid Array http://www.pideu.panasonic.de/pdf/184ext.pdf [5] REACH and RoHS Certificate http://www.pideu.panasonic.de/pdf/182ext2.jpg PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 30 of 33 DATE 07.01.2012 28 GENERAL INFORMATION (c) Panasonic Industrial Devices Europe GmbH 2012. All rights reserved. This product description does not lodge the claim to be complete and free of mistakes. Please contact the related product manager in every case. If we deliver ES samples to the customer, these samples have the status Engineering Samples. This means, the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and there may be differences to be published Data Sheet. Engineering Samples are not qualified and are not to be used for reliability testing or series production. Disclaimer: Customer acknowledges that samples may deviate from the Data Sheet and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by the use of the Engineering Sample other than for Evaluation Purposes, particularly the installation or integration in an other product to be sold by Customer, deviation or lapse in function of Engineering Sample, improper use of Engineering Samples. Panasonic disclaimes any liability for consequential and incidental damages. In case of any questions, please contact your local sales partner or the related product manager. 29 REGULATORY INFORMATION 29.1 FCC NOTICE The devices PAN1026, for details refer to Chapter 20, including the antennas, which are listed in 29.5, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407.transmitter Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 29.2 CAUTION The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 31 of 33 DATE 07.01.2012 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help 29.3 LABELING REQUIREMENTS The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier are FCC ID: T7VPAN10. This FCC identifier is valid for all PAN1026 modules, for details, see the Chapter 20. Ordering Information. In any case the end product must be labelled exterior with "Contains FCC ID: T7VPAN10" 29.4 ANTENNA WARNING For the related part number of PAN1026 refer to Chapter 20. Ordering Information. This devices are tested with a standard SMA connector and with the antennas listed below. When integrated in the OEMs product, these fixed antennas require installation preventing end-users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions. The FCC identifier for this device with the antenna listed in item 1 are the same (FCC ID: T7VPAN10). 29.5 APPROVED ANTENNA LIST Note: We are able to qualify your antenna and will add to this list as that process is completed. Item Part Number Manufacturer 2 LDA212G3110K Murata Frequency Band Type Gain (dBi) 2.4GHz Chip-Antenna +0.9 29.6 RF EXPOSURE PAN1026 To comply with FCC RF Exposure requirements, the Original Equipment Manufacturer (OEM) must ensure that the approved antenna in the previous table must be installed. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of PAN1026 with mounted ceramic antenna (FCC ID: T7VPAN10) is far below the FCC radio frequency exposure limits. Nevertheless, the PAN1026 shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 32 of 33 DATE 07.01.2012 30 INDUSTRY CANADA CERTIFICATION PAN1026 is licensed to meet the regulatory requirements of Industry Canada (IC), license: IC: 216Q-PAN10 Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in Table 20 above, having a maximum gain of 0.9 dBi. Antennas not included in this list or having a gain greater than 0.9 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to the model size the IC identifier is displayed in the installation instruction only and can not be displayed on the modules label due to the limited size (8.7x15.6mm). 30.1 IC NOTICE The devices PAN1026, for details refer to Chapter 20, including the antennas, which are listed in 29.5, complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-GEN. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 30.2 LABELING REQUIREMENTS The Original Equipment Manufacturer (OEM) must ensure that IC labeling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is 216Q-PAN10. This IC identifier is valid for all PAN1026 modules, for details, see the Chapter 20. Ordering Information. In any case the end product must be labelled exterior with "Contains IC: 216Q-PAN10" 31 EUROPEAN R&TTE DECLARATION OF CONFORMITY Hereby, Panasonic Industrial Devices Europe GmbH, declares that the Bluetooth module PAN1026 and their versions is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. As a result of the conformity assessment procedure described in Annex III of the Directive 1999/5/EC, the end-customer equipment should be labelled as follows: PAN1026 and their versions in the specified reference design can be used in the following countries: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, The Netherlands, the United Kingdom, Switzerland, and Norway. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION PRODUCT SPECIFICATION CLASS 2 BLUETOOTH LOW ENERGY SPP MODULE CUSTOMER'S CODE PANASONIC'S CODE ENW89837A3KF PAN1026 SUBJECT No. DS-1026-2400-102 REV. 0.2 PAGE 33 of 33 DATE 07.01.2012 32 LIFE SUPPORT POLICY This Panasonic product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic for any damages resulting. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de