14
Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that TAIYO YUDEN CO., LTD. shall not be responsible for any defects in products or equipment incor-
porating such products, which are caused under the conditions other than those specified in this catalog or indi-
vidual specification.
■ Please contact TAIYO YUDEN CO., LTD. for further details of product specifications as the individual specification
is available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact TAIYO YUDEN CO., LTD. for more detail in ad-
vance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called TAIYO YUDENs official sales channel).
It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel.
■ Please note that TAIYO YUDEN CO., LTD. shall have no responsibility for any controversies or disputes that may
occur in connection with a third party's intellectual property rights and other related rights arising from your usage
of products in this catalog. TAIYO YUDEN CO., LTD. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to Foreign Exchange and For-
eign Trade Control Law of Japan, U.S. Export Administration Regulations, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
14
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
109
NOISE SUPPRESSION COMPONENTS
／
FERRITE BEAD INDUCTORS
CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE)
REFLOWWAVE
chipbeads_e-E02R01
CHIP BEAD INDUCTORS FOR POWER LINES （FB SERIES M TYPE）
■PARTS NUMBER *Operating Temp. : -40～+125℃（Including self-generated heat）
F B △ M J 3 2 16 H S 800－T△
△＝Blank space
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨
①Series name
Code Series name
FB Ferrite bead
②Shape
Code Shape
M Rectangular chip
③Characteristics
Code Characteristics
J Standard
H High Impedance type
④Dimensions（L×W）
Code Type（inch） Dimensions
（L×W）［mm］
1608 1608（0603） 1.6×0.8
2125 2125（0805） 2.0×1.25
2012 2012（0805）
2016 2016（0806） 2.0×1.6
3216 3216（1206） 3.2×1.6
3225 3225（1210） 3.2×2.5
4516 4516（1806） 4.5×1.6
4525 4525（1810） 4.5×2.5
4532 4532（1812） 4.5×3.2
⑤Material
Code Material
HS Refer to impedance curves
for material differences
HM
HL
⑥Nominal impedance
Code
（example） Nominal impedance［Ω］
330 33
111 110
132 1300
⑦Impedance tolerance
Code Impedance tolerance
－ ±25％
N ±30％
⑧Packaging
Code Packaging
T Taping
⑨Internal code
Code Internal code
△ Standard
■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
Recommended Land Patterns
Surface Mounting
・Mounting and soldering conditions should be
checked beforehand.
Type A B C
FB MJ1608 1.0 1.0 1.0
FB MJ2125 1.4 1.2 1.65
FB MJ3216 1.4 2.2 2.0
FB MJ4516 1.75 3.5 2.0
FB MH1608 1.0 1.0 1.0
FB MH2012 1.4 1.2 1.65
FB MH2016 1.4 1.2 2.0
FB MH3216 1.4 2.2 2.0
FB MH3225 1.4 2.2 2.9
FB MH4516 1.75 3.5 2.0
FB MH4525 1.75 3.5 2.9
FB MH4532 1.75 3.5 3.7
Unit：mm
Type L W T e Standard quantity [pcs]
Paper tape Embossed tape
FB MJ1608
（0603）
1.6±0.2
（0.063±0.008）
0.8±0.2
（0.031±0.008）
0.8±0.2
（0.031±0.008）
0.3±0.2
（0.012±0.008） 4000 －
FB MJ2125
（0805）
2.0±0.2
（0.079±0.008）
1.25±0.2
（0.049±0.008）
0.85±0.2
（0.033±0.008）
0.5±0.3
（0.020±0.012） 4000 －
FB MJ3216
（1206）
3.2±0.3
（0.126±0.012）
1.6±0.2
（0.063±0.008）
1.1±0.2
（0.043±0.008）
0.5±0.3
（0.020±0.012） － 2000
FB MJ4516
（1806）
4.5±0.3
（0.177±0.012）
1.6±0.2
（0.063±0.008）
1.1±0.2
（0.043±0.008）
0.5±0.3
（0.020±0.012） － 2000
FB MH1608
（0603）
1.6±0.1
（0.063±0.004）
0.8±0.1
（0.031±0.004）
0.8±0.1
（0.031±0.004）
0.3±0.15
（0.012±0.006） 4000 －
FB MH2012
（0805）
2.0±0.2
（0.079±0.008）
1.25±0.2
（0.049±0.008）
0.85±0.2
（0.033±0.008）
0.5±0.3
（0.020±0.012） 4000 －
FB MH2016
（0806）
2.0±0.2
（0.079±0.008）
1.6±0.2
（0.063±0.008）
1.6±0.2
（0.063±0.008）
0.5±0.3
（0.020±0.012） － 2000
FB MH3216
（1206）
3.2±0.3
（0.126±0.012）
1.6±0.2
（0.063±0.008）
1.6±0.2
（0.063±0.008）
0.5±0.3
（0.020±0.012） － 2000
FB MH3225
（1210）
3.2±0.3
（0.126±0.012）
2.5±0.3
（0.098±0.012）
2.5±0.3
（0.098±0.012）
0.5±0.3
（0.020±0.012） － 1000
FB MH4516
（1806）
4.5±0.3
（0.177±0.012）
1.6±0.2
（0.063±0.008）
1.6±0.2
（0.063±0.008）
0.5±0.3
（0.020±0.012） － 2000
FB MH4525
（1810）
4.5±0.4
（0.177±0.016）
2.5±0.3
（0.098±0.012）
2.5±0.3
（0.098±0.012）
0.9±0.6
（0.035±0.024） － 1000
FB MH4532
（1812）
4.5±0.4
（0.177±0.016）
3.2±0.3
（0.126±0.012）
3.2±0.3
（0.126±0.012）
0.9±0.6
（0.035±0.024） － 2000
Unit：mm（inch）
14
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
110
NOISE SUPPRESSION COMPONENTS
／
FERRITE BEAD INDUCTORS
■PARTS NUMBER
Standard type
●FB MJ1608
FB MJ1608HS280NT RoHS 28 ±30％ 100 0.007 4.0 0.8 ±0.2
FB MJ1608HM230NT RoHS 23 ±30％ 100 0.007 4.0 0.8 ±0.2
●FB MJ2125
FB MJ2125HS250NT RoHS 25 ±30％ 100 0.004 6.0 0.85 ±0.2
FB MJ2125HS420-T RoHS 42 ±25％ 100 0.008 4.0 0.85 ±0.2
FB MJ2125HM210NT RoHS 21 ±30％ 100 0.004 6.0 0.85 ±0.2
FB MJ2125HM330-T RoHS 33 ±25％ 100 0.008 4.0 0.85 ±0.2
FB MJ2125HL8R0NT RoHS 8 ±30％ 100 0.008 4.0 0.85 ±0.2
●FB MJ3216
FB MJ3216HS480NT RoHS 48 ±30％ 100 0.005 6.0 1.1 ±0.2
FB MJ3216HS800-T RoHS 80 ±25％ 100 0.010 4.0 1.1 ±0.2
FB MJ3216HM380NT RoHS 38 ±30％ 100 0.005 6.0 1.1 ±0.2
FB MJ3216HM600-T RoHS 60 ±25％ 100 0.010 4.0 1.1 ±0.2
FB MJ3216HL160NT RoHS 16 ±30％ 100 0.012 4.0 1.1 ±0.2
●FB MJ4516
FB MJ4516HS720NT RoHS 72 ±30％ 100 0.007 6.0 1.1 ±0.2
FB MJ4516HS111-T RoHS 110 ±25％ 100 0.014 4.0 1.1 ±0.2
FB MJ4516HM560NT RoHS 56 ±30％ 100 0.007 6.0 1.1 ±0.2
FB MJ4516HM900-T RoHS 90 ±25％ 100 0.014 4.0 1.1 ±0.2
FB MJ4516HL230NT RoHS 23 ±30％ 100 0.014 3.5 1.1 ±0.2
High impedance type
●FB MH1608
FB MH1608HM470-T RoHS 47 ±25％ 100 0.020 3.5 0.8 ±0.1
FB MH1608HM600-T RoHS 60 ±25％ 100 0.025 3.0 0.8 ±0.1
FB MH1608HM101-T RoHS 100 ±25％ 100 0.035 2.5 0.8 ±0.1
FB MH1608HM151-T RoHS 150 ±25％ 100 0.050 2.1 0.8 ±0.1
FB MH1608HM221-T RoHS 220 ±25％ 100 0.070 1.8 0.8 ±0.1
FB MH1608HM331-T RoHS 330 ±25％ 100 0.130 1.2 0.8 ±0.1
FB MH1608HM471-T RoHS 470 ±25％ 100 0.150 1.0 0.8 ±0.1
FB MH1608HM601-T RoHS 600 ±25％ 100 0.170 0.9 0.8 ±0.1
FB MH1608HM102-T RoHS 1000 ±25％ 100 0.350 0.6 0.8 ±0.1
FB MH1608HL300-T RoHS 30 ±25％ 100 0.028 2.6 0.8 ±0.1
FB MH1608HL600-T RoHS 60 ±25％ 100 0.045 2.1 0.8 ±0.1
FB MH1608HL121-T RoHS 120 ±25％ 100 0.130 1.2 0.8 ±0.1
FB MH1608HL221-T RoHS 220 ±25％ 100 0.170 0.9 0.8 ±0.1
FB MH1608HL331-T RoHS 330 ±25％ 100 0.210 0.8 0.8 ±0.1
FB MH1608HL471-T RoHS 470 ±25％ 100 0.350 0.6 0.8 ±0.1
FB MH1608HL601-T RoHS 600 ±25％ 100 0.450 0.5 0.8 ±0.1
●FB MH2012
FB MH2012HM800-T RoHS 80 ±25％ 100 0.025 2.7 0.85 ±0.2
FB MH2012HM121-T RoHS 120 ±25％ 100 0.032 2.5 0.85 ±0.2
FB MH2012HM221-T RoHS 220 ±25％ 100 0.060 2.0 0.85 ±0.2
FB MH2012HM331-T RoHS 330 ±25％ 100 0.080 1.8 0.85 ±0.2
●FB MH2016
FB MH2016HM121NT RoHS 120 ±30％ 100 0.015 4.5 1.6 ±0.2
FB MH2016HM251NT RoHS 250 ±30％ 100 0.050 2.0 1.6 ±0.2
●FB MH3216
FB MH3216HM221NT RoHS 220 ±30％ 100 0.020 4.0 1.6 ±0.2
FB MH3216HM501NT RoHS 500 ±30％ 100 0.070 2.0 1.6 ±0.2
●FB MH3225
FB MH3225HM601NT RoHS 600 ±30％ 100 0.042 3.0 2.5 ±0.3
FB MH3225HM102NT RoHS 1000 ±30％ 100 0.100 2.0 2.5 ±0.3
FB MH3225HM202NT RoHS 2000 ±30％ 100 0.130 1.2 2.5 ±0.3
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Rated current
［A］（max.）
Thickness
［mm］
Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Thickness
［mm］
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Thickness
［mm］
Parts number EHS Nominal impedance
（Ω） Impedance tolerance
Parts number EHS Nominal impedance
（Ω） Impedance tolerance
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Rated current
［A］（max.）
Thickness
［mm］
Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Thickness
［mm］
Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Thickness
［mm］
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Parts number EHS
Rated current
［A］（max.）
Thickness
［mm］
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Nominal impedance
（Ω） Impedance tolerance
Rated current
［A］（max.）
Thickness
［mm］
Rated current
［A］（max.）
Thickness
［mm］
Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
chipbeads_e-E02R01
14
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
111
NOISE SUPPRESSION COMPONENTS
／
FERRITE BEAD INDUCTORS
■PARTS NUMBER
●FB MH4516
FB MH4516HM851NT RoHS 850 ±30％ 100 0.100 1.5 1.6 ±0.2
●FB MH4525
FB MH4525HM102NT RoHS 1000 ±30％ 100 0.060 3.0 2.5 ±0.3
FB MH4525HM162NT RoHS 1600 ±30％ 100 0.130 2.0 2.5 ±0.3
●FB MH4532
FB MH4532HM681-T RoHS 680 ±25％ 100 0.028 4.0 3.2 ±0.3
FB MH4532HM132-T RoHS 1300 ±25％ 100 0.060 3.0 3.2 ±0.3
FB MH4532HM202-T RoHS 2000 ±25％ 100 0.130 1.3 3.2 ±0.3
●High current type
FB MJ1608HS220NTR RoHS 22 ±30％ 100 0.004 7.5 0.8 ±0.2
FB MJ1608HS280NTR RoHS 28 ±30％ 100 0.006 6.0 0.8 ±0.2
FB MJ1608HM180NTR RoHS 18 ±30％ 100 0.004 7.5 0.8 ±0.2
FB MJ1608HM230NTR RoHS 23 ±30％ 100 0.006 6.0 0.8 ±0.2
Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Rated current
［A］（max.）
Thickness
［mm］
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Thickness
［mm］
Rated current
［A］（max.）
Thickness
［mm］
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Thickness
［mm］
Parts number EHS Nominal impedance
（Ω） Impedance tolerance Measuring frequency
［MHz］
DC Resistance
［Ω］（max.）
chipbeads_e-E02R01
14
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
112
NOISE SUPPRESSION COMPONENTS
／
FERRITE BEAD INDUCTORS
■ ELECTRICAL CHARACTERISTICS
■
FB MJ1608
■
FB MJ2125
■
FB MJ3216
FB MJ3216HL160NT
70
60
50
40
30
20
10
0
FB MJ4516HL230NT
100
90
80
70
60
50
40
30
20
10
0
■
FB MJ4516
14
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
113
NOISE SUPPRESSION COMPONENTS
／
FERRITE BEAD INDUCTORS
■ ELECTRICAL CHARACTERISTICS
1600
1400
1200
1000
800
600
400
200
01 10010 1000 10000
FB MH1608HM102-T
Z
R
X
1000
900
800
700
600
500
400
300
200
100
01 10010 1000 10000
FB MH1608HL221-T
Z
X
R
400
350
300
250
200
150
100
50
01 10010 1000 10000
FB MH2012HM800-T
Z
X
R
200
180
160
140
120
100
80
60
40
20
01 100 100010 10000
FB MH2016HM121NT
ZR
X
350
300
250
200
150
100
50
01 100 100010 10000
FB MH3216HM221NT
ZR
X
800
600
400
200
01 10010 1000
FB MH2016HM251NT
Z
R
X
800
600
400
200
01 10010 1000
FB MH3216HM501NT
X
ZR
400
350
300
250
200
150
100
50
01 10010 1000 10000
FB MH2012HM121-T
Z
X
R
400
350
300
250
200
150
100
50
01 10010 1000 10000
FB MH2012HM221-T
Z
X
R
800
600
400
200
01 10010 1000 10000
FB MH2012HM331-T
Z
X
R
1400
1200
1000
800
600
400
200
0
1 10010 1000 10000
FB MH1608HL331-T
Z
R
X
2000
1800
1600
1400
1200
1000
800
600
400
200
01 10010 1000 10000
FB MH1608HL471-T
Z
R
X
2500
2000
1500
1000
500
0
1 10010 1000 10000
FB MH1608HL601-T
Z
R
X
300
250
200
150
100
50
01 10010 1000 10000
FB MH1608HL300-T
Z
X
R
300
250
200
150
100
50
01 10010 1000 10000
FB MH1608HL600-T
Z
R
X
600
500
400
300
200
100
01 10010 1000 10000
FB MH1608HL121-T
Z
R
X
200
180
160
140
120
100
80
60
40
20
01 100 100010 10000
FB MH1608HM470-T
Z
R
X
200
180
160
140
120
100
80
60
40
20
01 100 100010 10000
FB MH1608HM600-T
Z
R
X
200
180
160
140
120
100
80
60
40
20
01 10010 1000 10000
FB MH1608HM101-T
Z
R
X
600
500
400
300
200
100
01 10010 1000 10000
FB MH1608HM151-T
Z
R
X
Standard type
600
500
400
300
200
100
01 10010 1000 10000
FB MH1608HM221-T
Z
X
R
600
500
400
300
200
100
01 10010 1000 10000
FB MH1608HM331-T
ZR
X
1600
1400
1200
1000
800
600
400
200
01 10010 1000 10000
FB MH1608HM471-T
Z
R
X
1600
1400
1200
1000
800
600
400
200
01 10010 1000 10000
FB MH1608HM601-T
Z
R
X
■
FB MH1608
■
FBMH2012
■
FB MH2016
■
FB MH3216
14
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
114
NOISE SUPPRESSION COMPONENTS
／
FERRITE BEAD INDUCTORS
1200
1000
200
800
600
400
01 10010 1000
FB MH4516HM851NT
R
X
Z
1200
1000
200
800
600
400
01 10010 1000
FB MH3225HM601NT
R
X
Z
30
25
20
15
10
5
01 10010 1000 10000
FB MJ1608HS220NTR
Z
R
X
■ ELECTRICAL CHARACTERISTICS
Standard type
1200
1000
200
800
600
400
01 10010 1000
FB MH3225HM102NT
Z
R
X
1800
1600
1400
1200
1000
200
800
600
400
01 10010 1000
FB MH4532HM681-T
ZR
X
1800
1600
1400
1200
1000
200
800
600
400
01 10010 1000
FB M4532HM132-T
Z
R
X
2500
2000
1500
1000
500
0
1 10010 1000
FB M4532HM202-T
X
Z
R
2500
2000
1500
1000
500
01 10010 1000
FB MH3225HM202NT
R
X
Z
40
35
30
25
20
15
10
5
01 10010 1000 10000
FB J1608HM180NTR
Z
R
X
1800
1600
1400
1200
1000
200
800
600
400
01 10010 1000
FB MH4525HM102NT
R
X
Z
1800
1600
1400
1200
1000
200
800
600
400
01 10010 1000
FB MH4525HM162NT
ZR
X
■
FB MH3225
■
High current type
■
FB MH4525
■
FB MH4532
■
FB MH4516
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_pack_e-E02R01
CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE)
■PACKAGING
①Minimum Quantity
Type Standard Quantity［pcs］
Paper Tape Embossed Tape
1608（0603） 4000 －
2125（0805） 4000 －
2012（0805） 4000 －
2016（0806） － 2000
3216（1206） － 2000
3225（1210） － 1000
4516（1806） － 2000
4525（1810） － 1000
4532（1812） － 2000
②Tape Material
●Card board carrier tape
Top tape
Base tape
Sprocket hole
Bottom tape Chip cavity
Chip
Chip Filled
●Embossed tape
Top tape
Base tape
Sprocket hole
Chip cavity
Chip
Chip Filled
③Taping Dimensions
●Paper tape (0.315 inches wide)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_pack_e-E02R01
Type Chip Cavity Insertion Pitch Tape Thickness
A B F T
FBMJ1608
FBMH1608
（0603）
1.0±0.2
（0.039±0.008）
1.8±0.2
（0.071±0.008）
4.0±0.2
（0.157±0.008）
1.1max
（0.043max）
FBMJ2125
FBMH2012
（0805）
1.5±0.2
（0.059±0.008）
2.3±0.2
（0.091±0.008）
4.0±0.2
（0.157±0.008）
1.1max
（0.043max）
Unit : mm（inch）
●Embossed tape (0.315 inches wide)
Type Chip Cavity Insertion Pitch Tape Thickness
A B F K T
FBMH2016
（0806）
1.8±0.2
（0.071±0.008）
2.2±0.2
（0.087±0.008）
4.0±0.2
（0.157±0.008）
2.6max
（0.102max）
0.6max
（0.024max）
FBMJ3216
（1206）
1.9±0.2
（0.075±0.008）
3.5±0.2
（0.138±0.008）
4.0±0.2
（0.157±0.008）
1.5max
（0.059max）
0.3max
（0.012max）
FBMH3216
（1206）
1.9±0.2
（0.075±0.008）
3.5±0.2
（0.138±0.008）
4.0±0.2
（0.157±0.008）
2.6max
（0.102max）
0.6max
（0.024max）
FBMH3225
（1210）
2.8±0.2
（0.110±0.008）
3.5±0.2
（0.138±0.008）
4.0±0.2
（0.157±0.008）
4.0max
（0.157max）
0.6max
（0.024max）
Unit : mm（inch）
●Embossed tape (0.472 inches wide)
Type Chip Cavity Insertion Pitch Tape Thickness
A B F K T
FBMJ4516
（1806）
1.9±0.2
（0.075±0.008）
4.9±0.2
（0.193±0.008）
4.0±0.2
（0.157±0.008）
1.5max
（0.059max）
0.3max
（0.012max）
FBMH4516
（1806）
1.9±0.2
（0.075±0.008）
4.9±0.2
（0.193±0.008）
4.0±0.2
（0.157±0.008）
2.6max
（0.102max）
0.6max
（0.024max）
FBMH4525
（1810）
2.9±0.2
（0.114±0.008）
4.9±0.2
（0.193±0.008）
4.0±0.2
（0.157±0.008）
4.0max
（0.157max）
0.6max
（0.024max）
FBMH4532
（1812）
3.6±0.2
（0.142±0.008）
4.9±0.2
（0.193±0.008）
8.0±0.2
（0.315±0.008）
4.0max
（0.157max）
0.6max
（0.024max）
Unit : mm（inch）
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_pack_e-E02R01
④Leader and Blank portion
⑤Reel size
2.0±0.5
（0.079±0.020）
φ21.0±0.8
（φ0.827±0.031）
φ13.0±0.5
（φ0.512±0.020）
R1.0
φd
t
φD
W
Type φD φd W t
FBMJ1608
180＋0/－3
（7.09＋0/－0.118 ）
60＋1/－0
（2.36＋0.039/－0 ）
10.0±1.5
（0.394±0.059）
2.5max
(0.098max)
FBMJ2125
FBMJ3216
FBMJ4516 14.0±1.5
（0.551±0.059）
FBMH1608
10.0±1.5
（0.394±0.059）
FBMH2012
FBMH2016
FBMH3216
FBMH3225
FBMH4516 14.0±1.5
（0.551±0.059）
FBMH4525
FBMH4532 330±2.0
（12.99±0.080）
100±1.0
（3.94±0.039）
14.0±2.0
（0.551±0.080）
3.0max
(1.181max)
Unit : mm（inch）
⑥Top tape strength
The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_reli_e-E02R01
CHIP BEAD INDUCTORS FOR POWER LINE (FB SERIES M TYPE)
■RELIABILITY DATA
1. Operating Temperature Range
Specified Value －40℃～＋125℃
Including self-generated heat
2. Storage Temperature Range
Specified Value －40℃～＋85℃
Test Methods and
Remarks *Note: -5 to ＋40℃ in taped packaging
3. Impedance
Specified Value Within the specified tolerance
Test Methods and
Remarks
Measuring equipment : Impedance analyzer (HP4291A) or its equivalent
Measuring frequency : 100±1 MHz
4. DC Resistance
Specified Value Within the specified range
Test Methods and
Remarks
Four-terminal method
Measuring equipment : Milliohm High-Tester 3226 (Hioki Denki) or its equivalent
5. Rated Current
Specified Value Within the specified range
6. Vibration
Specified Value Appearance : No significant abnormality
Impedance change : Within ±30% of the initial value
Test Methods and
Remarks
According to JIS C 0040.
Vibration type : A
Time : 2 hrs each in X,Y, and Z directions Total: 6 hrs
Frequency range : 10 to 55 to 10Hz (/min.)
Amplitude : 1.5 mm (shall not exceed acceleration 196m/s2)
Mounting method : Soldering onto PC board
7. Solderability
Specified Value 90% or more of immersed surface of terminal electrode shall be covered with fresh solder.
Test Methods and
Remarks
Solder temperature : 230±5℃
Immersion time : 4±1 sec.
Preconditioning : Immersion into flux.
Immersion and Removal speed : 25mm/sec.
8. Resistance to Soldering Heat
Specified Value Appearance : No significant abnormality
Impedance change : Within ±30% of the initial value
Test Methods and
Remarks
Preheating : 150℃ for 3 min.
Resistance to Soldering Heat : 260±5℃
Duration : 10±0.5 sec.
Preconditioning : Immersion into flux.
Immersion and Removal speed : 25mm/sec.
Recovery : 2 to 3 hrs of recovery under the standard condition after the test.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_reli_e-E02R01
9. Thermal Shock
Specified Value Appearance : No significant abnormality
Impedance change : Within＋50/－10% of the initial value
Test Methods and
Remarks
According to JIS C 0025.
Conditions for 1 cycle
Step Temperature (℃) Duration (min.)
1 －40±3℃ 30±3
2 Room Temperature Within 3
3 85±2℃ 30±3
4 Room Temperature Within 3
Number of cycles : 100
Mounting method : Soldering onto PC board
Recovery : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
10. Resistance to Humidity (steady state)
Specified Value Appearances : No significant abnormality
Impedance change : Within ±30% of the initial value
Test Methods and
Remarks
Temperature : 40±2℃
Humidity : 90 to 95% RH
Duration : 500＋24/－0
Mounting method : Soldering onto PC board
Recovery : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
11. Loading under Damp Heat
Specified Value Appearance No significant abnormality
Impedance change Within ±30% of the initial value
Test Methods and
Remarks
Temperature : 40±2℃
Humidity : 90 to 95%RH
Applied current : Rated current
Duration : 500＋24/－0 hrs
Mounting method : Soldering onto PC board
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
12. High Temperature Loading Test
Specified Value Appearance : No significant abnormality
Impedance change : Within ±30% of the initial value
Test Methods and
Remarks
Temperature : 85±2℃
Duration : 500＋24/－0 hrs
Applied current : Rated current
Mounting method : Soldering onto PC board
Recovery : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
13. Bending Strength
Specified Value Appearance : No mechanical damage.
Test Methods and
Remarks
Warp : 2mm
Testing board : Glass epoxy-resin substrate
Thickness : 0.8mm
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_reli_e-E02R01
14. Adhesion of Electrode
Specified Value No separation or indication of separation of electrode.
Test Methods and
Remarks
Applied force : 5N
Duration : 10 sec.
Note on standard condition: "standard condition" referred to herein is defined as follows:
5 to 35℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure.
When there are questions concerning measurement results:
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity and 86 to 106kPa of air
pressure. Unless otherwise specified, all the tests are conducted under the "standard condition."
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_prec_e-E02R01
CHIP BEAD INDUCTORS FOR POWER LINE （FB SERIES M TYPE）
■PRECAUTIONS
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
◆Rated current
1. Rated current of this product is shown in this catalogue, but please be sure to have the base board designed with adequate inspection in
case of the generation of heat becomes high within the rated current range when the base board is in high resistance or in bad heating
conditions.
2. PCB Design
Precautions ◆Land pattern design
1. Please refer to a recommended land pattern.
3. Considerations for automatic placement
Precautions
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
considerations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
◆Reflow soldering
1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering
heat, etc. sufficiently.
◆Preheating when soldering
Heating : The temperature difference between soldering and remaining heat should not be greater than 150℃.
Cooling : The temperature difference between the components and cleaning process should not be greater than 100℃.
◆Recommended conditions for using a soldering iron
Put the soldering iron on the land-pattern.
Soldering iron's temperature - Below 350℃
Duration - 3 seconds or less
The soldering iron should not directly touch the inductor.
Technical
considerations
◆Wave, Reflow, Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
【Recommended reflow condition】
◆Preheating when soldering
1. There is a case that products get damaged by a heat shock.
◆Recommended conditions for using a soldering iron
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_prec_e-E02R01
5. Handling
Precautions
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Setting PC boards
1. When setting a chip mounted base board, please make sure that there is no residual stress to the chip by distortion in the board or at
screw part.
◆Breakaway PC boards (splitting along perforations)
1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the
board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
Technical
considerations
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Setting PC boards
1. There is a case that a characteristic varies with residual stress.
◆Breakaway PC boards (splitting along perforations)
1. Planning pattern configurations and the position of products should be carefully performed to minimize stress.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
6. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
・Recommended conditions
Ambient temperature 0～40℃
Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, inductors should be used within 6 months from the time of delivery.
Technical
considerations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.
