Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC370LP4 / 370LP4E v04.0110 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT FREQ. MULTIPLIERS - ACTIVE - SMT 7 Typical Applications Features The HMC370LP4(E) is ideal for: Output Power: 0 dBm * Point-to-Point & VSAT Radios Sub-Harmonic Suppression: >22 dBc * Fiber Optic SSB Phase Noise: -140 dBc/Hz * Military Single Supply: +5V @ 55 mA 24 Lead 4x4 mm SMT Package: 16 mm2 Functional Diagram General Description The HMC370LP4(E) is an active miniature x4 frequency multiplier utilizing InGaP GaAs HBT technology in a 4x4 mm leadless surface mount package. Power output is 0 dBm typical from a 5V supply voltage and varies little vs. input power, temperature and supply voltage. Suppression of undesired fundamental and sub-harmonics is >22 dBc typical with respect to output signal level. The low additive SSB phase noise of -140 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. The HMC370LP4(E) are ideal for use in LO multiplier chains allowing reduced parts count vs. traditional approaches. Electrical Specifi cations, TA = +25 C, Vcc = 5V Parameter Min. Frequency Range, Input Frequency Range, Output Max. -15 Output Power -4 Units GHz 14.4 - 16.4 Input Power Range GHz +5 dBm 0 dBm Sub-Harmonic Suppression 22 dBc Input Return Loss 18 dB Output Return Loss 7 dB SSB Phase Noise (100 kHz Offset) Supply Current (Icc) 7 - 46 Typ. 3.6 - 4.1 Pin = 0 dBm -140 55 dBc/Hz 73 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com mA HMC370LP4 / 370LP4E v03.0907 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT Output Power vs. Drive Level 4 4 3 3 2 2 OUTPUT POWER (dBm) 1 0 -1 -2 -3 +25 C +85 C -40 C -4 7 1 0 -1 -2 -20 dBm -15 dBm -10 dBm -5 dBm 0 dBm +5 dBm -3 -4 -5 -5 -6 -6 14 14.4 14.8 15.2 15.6 16 16.4 16.8 14 14.4 OUTPUT FREQUENCY (GHz) 0 3 -5 RETURN LOSS (dB) 2 1 0 -1 -2 Vcc=4.5V Vcc=5.0V Vcc=5.5V 16 16.4 16.8 -10 -15 -20 -25 -30 +25 C +85 C -40 C -35 -5 -40 -6 14 14.4 14.8 15.2 15.6 16 16.4 0 16.8 1 2 3 4 FREQUENCY (GHz) OUTPUT FREQUENCY (GHz) 5 6 Output Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) OUTPUT POWER (dBm) 15.6 Input Return Loss vs. Temperature 4 -4 15.2 OUTPUT FREQUENCY (GHz) Output Power vs. Supply Voltage @ -10 dBm Drive Level -3 14.8 FREQ. MULTIPLIERS - ACTIVE - SMT OUTPUT POWER (dBm) Output Power vs. Temperature @ -10 dBm Drive Level -10 -15 +25 C +85 C -40 C -20 -25 8 9 10 11 12 13 14 15 16 17 18 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 47 HMC370LP4 / 370LP4E v03.0907 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT SSB Phase Noise Performance, Fout= 15.0 GHz Output Spectrum 7 - 48 0 10 -20 SSB PHASE NOISE (dBc/Hz) 0 OUTPUT POWER (dBm) FREQ. MULTIPLIERS - ACTIVE - SMT 7 -10 -20 -30 -40 -60 Pin = 0 dBm Pin = -10 dBm -80 -100 -40 -120 -140 -50 -160 -60 0 2 4 6 8 10 12 14 16 FREQUENCY (GHz) 18 20 22 24 26 10 2 10 3 10 4 10 5 10 OFFSET FREQUENCY (Hz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 10 7 HMC370LP4 / 370LP4E v03.0907 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT Typical Supply Current vs. Vcc RF Input (Vcc = +5V) +20 dBm Vcc (V) Icc (mA) Vcc +5.5V 4.5 54 Channel Temperature 135 C 5.0 55 5.5 57 Continuous Pdiss (T=85 C) (derate 8.1 mW/C above 85 C) 530 mW Thermal Resistance (Rth) (junction to ground paddle) 123.6 C/W Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C Note: Multiplier will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing 7 FREQ. MULTIPLIERS - ACTIVE - SMT Absolute Maximum Ratings NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC370LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC370LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H370 XXXX [2] H370 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 49 HMC370LP4 / 370LP4E v03.0907 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT Pin Description FREQ. MULTIPLIERS - ACTIVE - SMT 7 7 - 50 Pin Number Function Description 1, 2, 5-14, 17, 18, 20-24 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 3 RFIN RF input needs to be DC blocked only if there is an external DC voltage applied to RF IN. 4, 15 GND All ground leads and ground paddle must be soldered to PCB RF/DC ground. 16 RFOUT Multiplied Output. AC coupled. No external DC blocks necessary. 19 Vcc Supply voltage 5V 0.5V. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC370LP4 / 370LP4E v03.0907 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT Evaluation PCB FREQ. MULTIPLIERS - ACTIVE - SMT 7 List of Materials for Evaluation PCB 106137 [1] Item Description J1 - J3 PCB Mount SMA Connector C1 1,000 pF Capacitor, 0603 Pkg. U1 HMC370LP4(E) x4 Active Multiplier PCB [2] 104610 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the application should be generated with proper RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 51 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC370LP4E 106137-HMC370LP4 HMC370LP4 HMC370LP4ETR HMC370LP4TR