Z - LEAD SURFACE MOUNT SPECIFICATION AC AXIAL CEMENTED WIREWOUND RESISTOR & PR POWER METAL FILM RESISTORS FEATURES * Surface mounted version * Low cost alternative for SMD molded resistor * High power dissipation in small volume * High pulse load handling capabilities * High temperature silicone coating TECHNOLOGY Wire wound resistor AC03 / AC05 The resistor element is a resistive wire, which is wound, in a single layer on a ceramic rod. Metal caps are pressed over the ends of the rod. The ends of the resistance wire and tinned copper-clad leads are connected to the caps by welding. The resistor is coated with green silicon cement which is non-flammable, will not drip even at high overloads and is resistant to most commonly used cleaning solvents, in accordance with "MIL-STD-202E, method 215" and "IEC 60068-2-45". Metal film power resistor PR03 A homogenous film of metal alloy is deposited on a high-grade ceramic core. The leads are welded on this caps and a helical groove has been cut in the resistive layer. The resistor is coated with red silicon cement which is non-flammable, will not drip even at high overloads and is resistant to most commonly used cleaning solvents, providing electrical, mechanical and climatic protection. PHOENIX DO BRASIL LTDA AC PR Z LEAD All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. Preliminary Specification Revision July 28 2005 Page 1 of 9 QUICK REFERENCE DATA DESCRIPTION Resistance range ( 1 PR03 ) 0.33 - 1 M 1 - 1 M 5%, E24 1%, E24/E96 Tolerance and series AC03 AC05 0.1 - 5.1 k 0.1 - 8.2 k 5% and 1%, E24/E96 Maximum dissipation at Tamb = 25C 3W 3W 5W Limiting voltage (DC or RMS) 750 V - - Rated voltage ( 2 ) Temperature coefficient ( Pn x R 3 ) 250 ppm/C R R < 10 : 0 to 600 ppm/C 10 : - 80 to + 140 ppm/C (2) Basic specification IEC 60115-1 and 60115-4 IEC60 115-1 Climatic category (IEC 60068) 55/155/56 40/200/56 Stability R/Rmax after: Load 5% + 0.1 1% + 0.1 5% + 0.1 5% + 0.1 Climatic tests 3% + 0.1 1% + 0.1 1% + 0.05 1% + 0.05 Resistance to soldering heat 1% + 0.05 0.5% + 0.05 0.5% + 0.05 0.5% + 0.05 (1) Special resistive values available on request (2) Maximum rated voltage is the limiting voltage (3) Temperature coefficient 30, 50 and 90 ppm/C available on request PHOENIX DO BRASIL LTDA AC PR Z LEAD All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. Preliminary Specification Revision July 28 2005 Page 2 of 9 MECHANICAL DATA Standard pad sizes Table 1. (1) TYPE L max D max d P1 0.039) ( h max W max A min B max (1) C min E min PR03 16.5 (0.650) 5.2 (0.205) 0.8 FeCu (0.031) 21.0 (0.827) 5.0 (0.197) 7.5 (0.295) 24.5 (0.965) 17.5 (0.689) 3.5 (0.138) 8.0 (0.315) AC03 12.5 (0.492) 5.5 (0.22) 0.8 FeCu (0.031) 16.5 (0.649) 5.0 (0.197) 7.5 (0.295) 20.0 (0.787) 13.0 (0.512) 3.5 (0.138) 8.0 (0.315) AC05 17.0 (0.669) 7.5 (0.295) 0.8 FeCu (0.031) 21.0 (0.827) 5.0 (0.197) 7.5 (0.295) 24.5 (0.965) 17.5 (0.689) 3.5 (0.138) 8.0 (0.315) (1) (2) (1) (1) Dimensions in mm (inches) (1) Other dimensions available under request (2) Dimensions to be confirmed PHOENIX DO BRASIL LTDA AC PR Z LEAD All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. Preliminary Specification Revision July 28 2005 Page 3 of 9 ELECTRICAL CHARACTERISTICS DERATING: AC03 AND AC05 120 Pmax (%) 100 80 60 40 20 0 0 25 50 75 100 125 150 175 200 Tamb (C) Maximum dissipation (Pmax) in percentage of rated power as a function of ambient temperature (Tamb) DERATING: PR03 120 Pmax (%) 100 80 60 40 20 0 0 25 50 75 100 125 150 175 Tamb (C) Maximum dissipation (Pmax) in percentage of rated power as a function of ambient temperature (Tamb) PHOENIX DO BRASIL LTDA AC PR Z LEAD All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. Preliminary Specification Revision July 28 2005 Page 4 of 9 MARKING WIRE WOUND RESISTOR The resistor is marked with the nominal resistance value, the tolerance on the resistance and the rated dissipation at Tamb = 25 C. For values up to 910 , the R is used as the decimal point. For values of 1 K and upwards, the letter K is used as the decimal point for the K indication. Example: 6K8 5% 5W FILM RESISTOR The nominal resistance and tolerance are marked on the resistor using four or five colored bands in accordance with IEC publication 60062 "color code for fixed resistors". Standard values of nominal resistance are taken from the E24/E96 series for resistors with a tolerance of 5% or 1%. The values of the E24/E96 series are in accordance with "IEC publication 60063". ORDERING INFORMATION Table 2. Ordering code. TYPE LEAD TOLERANCE 1% PR03 QUANTITY (pcs) Under request 200 5% AC03 0.80 FeCu (0.031) AC05 ORDERING CODE PACKAGING 2306 199 55xxx 1% 200 IN BOX 5% Under request 2306 326 55xxx 1% 200 5% Under request 2306 321 55xxx Dimensions unless specified in mm (inches) The resistors have a 12 digit ordering code starting with 2306. The subsequent 6 or 7 digits indicate the resistor type and packaging see table 2. For 5% tolerance the remaining 3 digits indicate the resistance value; - The first 2 digits indicate the resistance value. - The last digit indicates the resistance decade in accordance with table 3. For 1% tolerance the remaining 4 digits indicate the resistance value; - The first 3 digits indicate the resistance value. - The last digit indicates the resistance decade in accordance with table 3. PHOENIX DO BRASIL LTDA AC PR Z LEAD All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. Preliminary Specification Revision July 28 2005 Page 5 of 9 Table 3. Last digit of ordering code. RESISTANCE DECADE (5%) RESISTANCE DECADE (1%) LAST DIGIT 0.1 - 0.91 - 7 1 - 9.1 1 - 9.76 8 10 - 91 10 - 97.6 9 100 - 910 100 - 976 1 1 - 9.1 k 1 - 9.76 k 2 10 - 91 k 10 - 97.6 k 3 100 - 910 k 100 - 976 k 4 1 M 1 M 5 Example: PR03, 15000 , 5% is 2306 199 55153 PACKAGING 200 pieces per box TESTS AND REQUIREMENTS WIRE WOUND RESISTOR (AC03 AND AC05) Essentially all tests are carried out in accordance to the schedule of IEC publications 60115 - 1, category 40/200/56 (rated temperature range - 40 to + 200 C; damp heat, long term, 56 days and along the lines of IEC publications 60068-2); "Recommended basic climatic and mechanical robustness testing procedure for electronic components" and under standard atmosphere conditions according to IEC 60068-1 subclause 5.3, unless otherwise specified. In some instances deviations from IEC applications were necessary for our method specified. Table 5. Test and requirements. IEC 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS 4.8 - Temperature coefficient Between - 40 C and + 200 C: R < 10 R 10 0 to 600 ppm/C - 80 to +140 ppm / C PHOENIX DO BRASIL LTDA AC PR Z LEAD All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. Preliminary Specification Revision July 28 2005 Page 6 of 9 IEC 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS 4.13 - Short time overload Room temperature; dissipation 10 x Pn; 5 s (voltage not more than 1000 V / 25 mm) R/Rmax 2% + 0.1 4.16 21(U) Robustness of terminations: 4.16.2 21(Ua) Tensile all samples Load 10 N; 10 s No visual damage R/Rmax 0.5% + 0.05 4.16.3 21(Ub) Bending half number of samples Load 5 N; 4 x 90 4.16.4 21(Uc) Torsion other half number of samples 2 x 180 in opposite directions 4.17 20(Ta) Solderability (after ageing) 16 h at 155 C; leads immersed in flux 600, leads immersed 2 mm for 2 0.5 s in a solder bath at 235 5 C Good tinning; ( 95% covered) no visible damage 4.18 20(Tb) Resistance to soldering heat Thermal shock: 3 s; 350 10 C; 2.5 mm from body R/Rmax 0.5% + 0.05 4.19 14(Na) Rapid change of temperature 30 minutes at - 40 C and 30 minutes at + 200 C; 5 cycles No visible damage R/Rmax 1% + 0.05 4.22 6(Fc) Vibration Frequency 10 to 500 Hz 0.75 mm or acceleration 10 g, three directions; total 6 h (3 x 2 h) No visible damage R/Rmax 0.5% + 0.05 4.23 Climatic sequence 4.23.2 2(Ba) Dry heat 16 h; + 200 C 4.23.3 30(Db) Damp heat (accelerated) 1st cycle 24 h; 25 C to 55 C; 90 to 100% R.H. R/Rmax 1% + 0.05 4.23.4 1(Aa) Cold 2 h; - 40 C 4.23.6 30(Db) Damp heat (accelerated) remaining cycles 5 days; 25 C to 55 C; 90 to 100% R.H. 4.24 3(Ca) Damp heat (steady state) 56 days; 40 C; 90 to 95% R.H.; loaded with 0.01Pn No visible damage R/Rmax 1% + 0.05 4.25.1 - Endurance (at 25 C) 1000 h load with 0.9 Pn; 1.5 h ON and 0.5 h OFF. No visible damage R/Rmax 5% + 0.1 PHOENIX DO BRASIL LTDA AC PR Z LEAD All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. Preliminary Specification Revision July 28 2005 Page 7 of 9 IEC 60115-1 CLAUSE IEC 60068-2 TEST METHOD 4.29 45 (Xa) TEST PROCEDURE REQUIREMENTS Component solvent resistance Isopropyl alcohol followed by brushing in accordance with MIL STD 202 No visible damage FILM RESISTOR (PR03) Essentially all tests are carried out in accordance to the schedule of IEC publications 60115 - 1, category 55/155/56 (rated temperature range - 55 C to + 155 C; damp heat, long term, 56 days and along the lines of IEC publications 60068-2); "Recommended basic climatic and mechanical robustness testing procedure for electronic components" and under standard atmosphere conditions according to IEC 60068-1 subclause 5.3, unless otherwise specified. In some instances deviations from IEC applications were necessary for our method specified. Table 7. Test and requirements. IEC 60115-1 CLAUSE IEC 60068-2 TEST METHOD REQUIREMENTS TEST PROCEDURE PR03 Tol 5% 4.6.1.1 4.7 IEC 60115-1 CLAUSE PR03 Tol 1% - Insulation resistance 500 V (DC) during 1 minute, V-block method Rins min 104 M - Voltage proof on insulation 500 V (RMS) during 1 minute, V-block method. No breakdown or flashover IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PR03 Tol 5% 4.8 - Temperature coefficient 4.16 21(U) Robustness of terminations: 4.16.2 21(Ua1) Tensile all samples Load 10 N; 10 s 4.16.3 21(Ub) Bending half number of samples Load 5 N; 4 x 90 4.16.4 21(Uc) Torsion other half of samples 3 x 360 in opposite directions PHOENIX DO BRASIL LTDA Between - 55 C and + 155 C AC PR Z LEAD All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. PR03 Tol 1% 250 ppm/C No damage R/Rmax 0.5% + 0.05 Preliminary Specification Revision July 28 2005 Page 8 of 9 IEC 60115-1 CLAUSE IEC 60068-2 TEST METHOD REQUIREMENTS TEST PROCEDURE PR03 Tol 5% 4.17 20(Ta) Solderability (after ageing) 16 h at 155 C; immersed in flux 600, leads immersed 2 mm for 2 0.5 s in a solder bath at 235 5 C 4.18 20(Tb) Resistance to soldering heat Thermal shock: 3 s; 350 C; 6 mm from body 4.19 14(Na) Rapid change of temperature 30 minutes at - 55 C and 30 minutes at + 155 C; 5 cycles TEST PROCEDURE IEC 60115-1 CLAUSE IEC 60068-2 TEST METHOD Good tinning (95% covered) No damage R/Rmax 1% + 0.05 6(Fc) 4.23 R/Rmax 0.5% + 0.05 No visual damage R/Rmax 2%+0.05 R/Rmax 1%+0.05 REQUIREMENTS PR03 Tol 5% 4.22 PR03 Tol 1% Vibration Frequency 10 to 500 Hz, displacement 1.5 mm or acceleration 10g; three directions; total 6 h (3 x 2 h) PR03 Tol 1% No damage R/Rmax 0.5% +0.05 Climatic sequence: 4.23.2 2(Ba) Dry heat 16 h; 155 C 4.23.3 30(Db) Damp heat (accelerated) st 1 cycle 24 h; 25 C to 55 C; 90 to 100% RH 4.23.4 1(Aa) Cold 2 h; - 55 C 4.23.6 30(Db) Damp heat (accelerated) remaining cycles 5 days; 25 C to 55 C; 90 to 100% R.H. 4.24 3(Ca) Damp heat (steady state) 56 days; 40 C; 90 to 95% R.H.; loaded with 0.01 Pn 4.25.1 - Endurance (at 25 C) 1000 h loaded with Pn or Vmax, 1.5 h ON and 0.5 h OFF. 4.29 45(Xa) Component solvent resistance Isopropyl alcohol followed by brushing MI L STD 202 PHOENIX DO BRASIL LTDA AC PR Z LEAD All rights are reserved. Reproduction whole or in part is prohibited without the written consent of the copyright owner. 3 Rins min 10 M R/Rmax 3% + 0.05 R/Rmax 1% + 0.05 3 Rins min 10 M R/Rmax 3% + 0.05 R/Rmax 1% + 0.05 R/Rmax 5% + 0.05 R/Rmax 1% + 0.05 No visual damage Preliminary Specification Revision July 28 2005 Page 9 of 9