ACS1086SATR - STMICROELECTRONICS

This is information on a product in full production.

July 2012 Doc ID 6518 Rev 3 1/13

ACS108

Overvoltage protected AC switch (ACS™)

Datasheet  production data

Features

■Enables equipment to meet IEC 61000-4-5

surge with overvoltage crowbar technology

■High noise immunity against static dV/dt and

IEC 61000-4-4 burst

■Needs no external protection snubber or

varistor

■Reduces component count by up to 80% and

Interfaces directly with the micro-controller

■Common package tab connection supports

connection of several alternating current

switches on the same cooling pad

■VCL gives headroom before clamping then

crowbar action

Applications

■Alternating current on/off static switching in

appliances and industrial control systems

■Driving low power high inductive or resistive

loads like:

– relay, valve, solenoid, dispenser,

– pump, fan, low power motor, door lock

–lamp

Description

The ACS108 belongs to the AC switch range (built

with A. S. D.® technology). This high performance

switch can control a load of up to 0.8 A. The

ACS108 switch includes an overvoltage crowbar

structure to absorb the inductive turn-off energy,

and a gate level shifter driver to separate the

digital controller from the main switch. It is

triggered with a negative gate current flowing out

of the gate pin.

Figure 1. Functional diagram

®: A.S.D. is a registered trademark of STMicroelectronics

TM: ACS is a trademark of STMicroelectronics

Table 1. Device summary

Symbol Value Unit

IT(RMS) 0.8 A

VDRM, VRRM 600 and 800 V

IGT 10 mA

COM

OUT

COM

OUT G

SOT-223

ACS108-6SN

ACS108-8SN

TO-92

ACS108-6SA

ACS108-8SA

OUT

COM

COM Common drive reference to connect

to the mains

OUT Output to connect to the load.

G Gate input to connect to the controller

through gate resistor

www.st.com

Characteristics ACS108

2/13 Doc ID 6518 Rev 3

1 Characteristics

Table 2. Absolute maximum ratings (Tamb = 25 °C, unless otherwise specified)

Symbol Parameter Value Unit

IT(RMS) On-state rms current (full sine wave)

TO-92 Tamb = 64 °C 0.45 A

Tlead = 76 °C

0.8 A

SOT-223

S = 5 cm2

Tamb = 76 °C

Ttab = 104 °C

ITSM

Non repetitive surge peak on-state current

(full cycle sine wave, Tj initial = 25 °C)

F = 60 Hz t = 16.7 ms 13.7 A

F = 50 Hz t = 20 ms 13

I2t I²t Value for fusing tp = 10 ms 1.1 A2s

dI/dt Critical rate of rise of on-state current

IG = 2xIGT

, tr  100 ns F = 120 Hz Tj = 125 °C 100 A/µs

VPP Non repetitive mains peak mains voltage(1) 2kV

IGM Peak gate current tp = 20 µs Tj = 125 °C 1 A

VGM Peak positive gate voltage Tj = 125 °C 10 V

PG(AV) Average gate power dissipation Tj = 125 °C 0.1 W

Tstg

Storage junction temperature range

Operating junction temperature range

-40 to +150

-30 to +125 °C

1. According to test described by IEC 61000-4-5 standard and Figure 18

Table 3. Electrical characteristics (Tj = 25 °C, unless otherwise specified)

Symbol Test conditions Quadrant Value Unit

IGT(1)

1. Minimum IGT is guaranteed at 10% of IGT max

VOUT = 12 V, RL = 33 

II - III Max. 10 mA

VGT II - III Max. 1 V

VGD VOUT = VDRM, RL = 3.3 kTj = 125 °C II - III Min. 0.15 V

IH I

OUT = 100 mA Max. 10 mA

ILIG = 1.2 x IGT Max. 25 mA

dV/dt VOUT = 402 V, gate open, Tj = 125 °C Min. 2000 V/µs

VOUT = 536 V, gate open, Tj = 125 °C Min. 400 V/µs

(dI/dt)c Without snubber (15 V/µs), Tj = 125 °C, turn-off time  20 ms Min. 2 A/ms

VCL

ICL = 0.1 mA, tp = 1 ms, ACS108-6 Min. 650 V

ICL = 0.1 mA, tp = 1 ms, ACS108-8 Min. 850 V

ACS108 Characteristics

Doc ID 6518 Rev 3 3/13

Table 4. Static electrical characteristics

Symbol Parameter and test conditions Value Unit

VTM (1) ITM = 1.1 A, tp = 500 µs Tj = 25 °C Max. 1.3 V

Vt0 (1) Threshold voltage Tj = 125 °C Max. 0.85 V

RD (1) Dynamic resistance Tj = 125 °C Max. 300 m

IDRM

IRRM

VOUT = VDRM = VRRM

Tj = 25 °C Max. 2µA

Tj = 125 °C 0.2 mA

1. For both polarities of OUT referenced to COM

Table 5. Thermal resistance

Symbol Parameter Value Unit

Rth (j-l) Junction to lead (AC) TO-92 Max. 60

°C/W

Rth (j-t) Junction to tab (AC) SOT-223 Max. 25

Rth (j-a) Junction to ambient TO-92 Max. 150

S = 5 cm² SOT-223 Max. 60

Figure 2. Maximum power dissipation versus

on-state rms current

Figure 3. On-state rms current versus case

temperature (SOT223)

P (W)

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

α= 180°

I (A)

T(RMS)

180°

I (A)

T(RMS)

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

0 25 50 75 100 125

α=180°

SOT-223

T°C

Characteristics ACS108

4/13 Doc ID 6518 Rev 3

Figure 4. On-state rms current versus

ambient temperature

(free air convection)

Figure 5. Relative variation of thermal

impedance junction to ambient

versus pulse duration

I (A)

T(RMS)

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

0 25 50 75 100 125

Single layer Printed

circuit board FR4

Natural convection

TO-92

SOT-223

α=180°

T°C

K=[Z

th(j-a)

]

0.01

0.10

1.00

1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03

Zth(j-a)

SOT-223

Copper surface

area = 5cm²

TO-92

SOT-223

t (s)

Figure 6. Relative variation of holding and

latching current versus junction

temperature

Figure 7. Relative variation of IGT and VGT

versus junction temperature

0.0

0.5

1.0

1.5

2.0

2.5

3.0

-50 -25 0 25 50 75 100 125

]/I

=25 °C]

Tj(°C)

]/I

,[T

=25 °C]

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

-50 -25 0 25 50 75 100 125

IGT Q2

VGT Q2-Q3

IGT Q3

Tj(°C)

Figure 8. Surge peak on-state current versus

number of cycles

Figure 9. Non repetitive surge peak on-state

current for a sinusoidal pulse, and

corresponding value of I²t

TSM

(A)

1 10 100 1000

Non repetitive

initial=25 °C

TO-92

Repetitive

lead

= 76 °C

SOT-223

Repetitive

tab

= 104°C

One cycle

t=20ms

Number of cycles

ITSM(A), I²t (A²s)

1.E-01

1.E+00

1.E+01

1.E+02

1.E+03

0.01 0.10 1.00 10.00

ITSM

I²t

Sinusoidal pulse,

tp< 10 ms

Tjinitial = 25 °C

(ms)tp

ACS108 Characteristics

Doc ID 6518 Rev 3 5/13

Figure 10. On-state characteristics (maximal

values)

Figure 11. Relative variation of critical rate of

decrease of main current versus

junction temperature

ITM(A)

0.10

1.00

10.00

100.00

0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5

Tjmax.:

Vto= 0.85 V

Rd= 300 m0

Tj=25 °C

Tj=125 °C

VTM(V)

(dI/dt) [T ] / (dI/dt) [T =125 °C]

0.0

0.5

1.0

1.5

2.0

2.5

25 35 45 55 65 75 85 95 105 115 125

T (°C)

Figure 12. Relative variation of static dV/dt

immunity versus junction

temperature(1)

Figure 13. Relative variation of leakage

current versus junction

temperature

1. VD = VR = 402 V: Typical values above 5 kV/µs. Beyond equipment capability

dV/dt [Tj]/dV/dt[T

j=125°C]

25 50 75 100 125

VD=VR=536V

Tj(°C)

1.0E-03

1.0E-02

1.0E-01

1.0E+00

25 50 75 100 125

DRM

RRM

[Tj;V

DRM/

RRM

]/I

DRM

RRM

[Tj=125°C;8 00V]

VDRM=VRRM=600 V

VDRM=VRRM=800 V

Tj(°C)

Figure 14. Relative variation of critical rate of

decrease of main current (di/dt)c

versus (dV/dt)c

Figure 15. Thermal resistance junction to

ambient versus copper surface

under tab (SOT-223)

(dI/dt)

[(dV/dt)

] / Specified (dI/dt)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

0.1 1.0 10.0 100.0

Tj =125 °C

(dV/dt)c(V/µs)

th(j-a)

(°C/W)

100

120

140

0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

SOT-223

SCU(cm²)

Printed circuit board FR4

copper thickness = 35 µm

Alternating current mains switch - basic application ACS108

6/13 Doc ID 6518 Rev 3

2 Alternating current mains switch - basic application

The ACS108 switch is triggered by a negative gate current flowing from the gate pin G. The

switch can be driven directly by the digital controller through a resistor as shown in

Figure 16.

Thanks to its overvoltage protection and turn-off commutation performance, the ACS108

switch can drive a small power high inductive load with neither varistor nor additional turn-off

snubber.

Figure 16. Typical application schematic

2.1 Protection against overvoltage: the best choice is ACS

In comparison with standard Triacs the ACS108 is over-voltage self-protected, as specified

by the new parameter VCL. This feature is useful in two operating conditions: in case of turn-

off of very inductive load, and in case of surge voltage that can occur on the electrical

network.

2.1.1 High inductive load switch-off: turn-off overvoltage clamping

With high inductive and low RMS current loads the rate of decrease of the current is very

low. An overvoltage can occur when the gate current is removed and the OUT current is

lower than IH.

As shown in Figure 17, at the end of the last conduction half-cycle, the load current

decreases ➀. The load current reaches the holding current level IH ➁, and the ACS turns off

➂. The water valve, as an inductive load (up to 15 H), reacts as a current generator and an

overvoltage is created, which is clamped by the ACS ➃. The current flows through the ACS

avalanche and decreases linearly to zero. During this time, the voltage across the switch is

limited to the clamping voltage VCL. The energy stored in the inductance of the load is

dissipated in the clamping section that is designed for this purpose. When the energy has

been dissipated, the ACS voltage falls back to the mains voltage value (230 V rms, 50 Hz)➄.

AC Mains

ACS108

Valve

Power supply

MCU

Vdd

Vss Rg

220 Ω

ACS108 Alternating current mains switch - basic application

Doc ID 6518 Rev 3 7/13

Figure 17. Switching off of a high inductive load - typical clamping capability of

ACS108 (Tamb = 25 °C)

2.1.2 Alternating current mains transient voltage ruggedness

The ACS108 switch is able to withstand safely the AC mains transients either by clamping

the low energy spikes or by breaking-over when subjected to high energy shocks, even with

high turn-on current rises.

The test circuit shown in Figure 18 is representative of the final ACS108 application, and is

also used to test the AC switch according to the IEC 61000-4-5 standard conditions. Thanks

to the load limiting the current, the ACS108 switch withstands the voltage spikes up to 2 kV

above the peak mains voltage. The protection is based on an overvoltage crowbar

technology. Actually, the ACS108 breaks over safely as shown in Figure 19. The ACS108

recovers its blocking voltage capability after the surge (switch off back at the next zero

crossing of the current).

Such non-repetitive tests can be done 10 times on each AC mains voltage polarity.

Figure 18. Overvoltage ruggedness test circuit for resistive and inductive loads,

Tamb = 25 °C (conditions equivalent to IEC 61000-4-5 standard)

VCL

100 µs/div

(5 mA/div)

(200 V/div)

VCL

Load

220 Ω

ACS108

150 Ω5 µH

+2 kV surge

generator

OUT

COM

Mains

voltage

230 V rms

50 Hz

Alternating current mains switch - basic application ACS108

8/13 Doc ID 6518 Rev 3

Figure 19. Typical current and voltage waveforms across the ACS108 (+2 kV surge,

IEC 61000-4-5 standard)

IT(4 A/div)

VT(200 V/div)

IT max = 17.2 A

dIT/dt = 1.8 A/µs

500 ns/div

ACS108 Ordering information scheme

Doc ID 6518 Rev 3 9/13

3 Ordering information scheme

Figure 20. Ordering information scheme

ACS 1 08 - 6 S A -TR

AC switch series

Number of switches

Current

Voltage

Sensitivity

Package

Packing

08 = 0.8 A rms

6 = 600 V

8 = 800 V

S = 10 mA

A = TO-92

N = SOT-223

TR = Tape and reel 7” (SOT-223, 1000 pieces) 13” (TO-92, 2000 pieces)

AP = Ammopack (TO-92, 2000 pieces)

Blank = (TO-92, 2500 pieces)bulk

Package information ACS108

10/13 Doc ID 6518 Rev 3

4 Package information

●Epoxy meets UL94, V0

●Lead-free packages

In order to meet environmental requirements, ST offers these devices in different grades of

ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®

specifications, grade definitions and product status are available at: www.st.com.

ECOPACK® is an ST trademark.

Table 6. TO-92 dimensions

Ref

Dimensions

Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A1.35 0.053

B 4.70 0.185

C2.54 0.100

D 4.40 0.173

E 12.70 0.500

F 3.70 0.146

a 0.50 0.019

ACS108 Package information

Doc ID 6518 Rev 3 11/13

Figure 21. SOT-223 footprint (dimensions in mm)

Table 7. SOT-223 dimensions

Ref.

Dimensions

Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A1.800.071

A1 0.02 0.10 0.001 0.004

B 0.60 0.70 0.85 0.024 0.027 0.033

B1 2.90 3.00 3.15 0.114 0.118 0.124

c 0.24 0.26 0.35 0.009 0.010 0.014

D(1)

1. Do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15mm (0.006inches)

6.30 6.50 6.70 0.248 0.256 0.264

e 2.3 0.090

e1 4.6 0.181

E(1) 3.30 3.50 3.70 0.130 0.138 0.146

H 6.70 7.00 7.30 0.264 0.276 0.287

V 10° max

3.25

1.32

7.80

5.16

1.32

2.30 0.95

Ordering information ACS108

12/13 Doc ID 6518 Rev 3

5 Ordering information

6 Revision history

Table 8. Ordering information

Order code Marking Package Weight Base Qty Delivery mode

ACS108-6SA

ACS1 086SA

TO-92 0.2 g 2500 Bulk

ACS108-6SA-TR TO-92 0.2 g 2000 Tape and reel

ACS108-6SA-AP TO-92 0.2 g 2000 Ammopack

ACS108-6SN-TR ACS 108 6SN SOT-223 0.11 g 1000 Tape and reel

ACS108-8SA

ACS1 088SA

TO-92 0.2 g 2500 Bulk

ACS108-8SA-TR TO-92 0.2 g 2000 Tape and reel

ACS108-8SA-AP TO-92 0.2 g 2000 Ammopack

ACS108-8SN-TR ACS 108 8SN SOT-223 0.11 g 1000 Tape and reel

Table 9. Document revision history

Date Revision Changes

Apr_2004 1

Initial release. This datasheet covers order codes previously

described in the datasheet for ACS108-6S, Doc ID 11962, Rev 3

December 2010.

21-Jun-2005 2Marking information updated from ACSxxxx to ACS1xxx.

11-Jul-2012 3Removed 500 V devices and added 600 V and 800 V devices.

ACS108

Doc ID 6518 Rev 3 13/13

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the

right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any

time, without notice.

All ST products are sold pursuant to ST’s terms and conditions of sale.

Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no

liability whatsoever relating to the choice, selection or use of the ST products and services described herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this

document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products

or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such

third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED

WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS

OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT

RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING

APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,

DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE

GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void

any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any

liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America