SDR-120-24 - MEAN WELL ENTERPRISES

SPECIFICATION

MODEL

DCVOLTAGE

RATEDCURRENT

CURRENTRANGE

RATEDPOWER

PEAKCURRENT

PEAKPOWER Note.6

OUTPUT

VOLTAGE ADJ.RANGE

LINEREGULATION

LOADREGULATION

SETUP,RISETIME

HOLDUP TIME (Typ.)

VOLTAGERANGE Note.7

FREQUENCY RANGE

EFFICIENCY (Typ.)

INPUT

INRUSHCURRENT (Typ.)

LEAKAGECURRENT

OVERTEMPERATURE

SAFETY STANDARDS

WORKINGTEMP.

DCOKREALY CONTACTRATINGS(max.)

WORKINGHUMIDITY

STORAGETEMP.,HUMIDITY

TEMP.COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERLOAD

OVERVOLTAGE

ACCURRENT (Typ.)

1500ms,60ms/230VAC30 atfullload00ms,60ms/115VAC

20ms/230VAC20ms/115VACatfullload

88~264VAC124~370VDC

47~63Hz

89%

0.93/230VAC0.96/115VACatfullload

1.4A/115VAC0.7A/230VAC

29~33V

91%

56~65V

90.5%

35A/115VAC70A/230VAC

<1mA /240VAC

Normallyw morethan3 andthenshutdowno/pvoltageorkswithin110~150%ratedoutputpowerfor seconds

14~17V

>150%ratedpower,constantcurrentlimitingwithauto-recoverywithin3secondsandshutdowno/pvoltageafter3seconds

Protectiontype:Shutdowno/pvoltage,re-powerontorecover

95 5 (TSW:detectonheatsinkofpowerswitch)

Protectiontype:Shutdowno/pvoltage,recoversautomaticallyaftertemperaturegoesdown

UL508 TUVEN60950-1approved,

CompliancetoEN55022(CISPR22)ClassB, EN61000-3-2,-3

CompliancetoEN61000-4-2,3,4,5,6,8,11,EN55024,EN61000-6-2(EN50082-2),EN61204-3,heavyindustrylevel,criteria A,

SEMIF47,GL approved

-25~+70 (Referto"DeratingCurve")

60Vdc/0.3A,30Vdc/1A,30Vac/0.5A resistiveload

20~95%RHnon-condensing

-40~+85 ,10~95%RH

0.03%/ (0~50

Component:10~500Hz,2G10min./1cycle,60min.eachalongX, Y,Zaxes;Mounting:CompliancetoIEC60068-2-6

289.9Khrsmin.MIL-HDBK-217F(25 )

40*125.2*113.5mm(W*H*D)

0.67Kg;20pcs/14.4Kg/1.16CUFT

POWERFACTOR (Typ.)

SDR-120-24 SDR-120-48

24V 48V

5A 2.5A

0~5A 0~2.5A

120W 120W

7.5A 3.75A

100mVp-p 120mVp-p

24~28V 48~55V

1.0% 1.0%

0.5% 0.5%

1.0% 1.0%

SDR-120-12

12V

10A

0~10A

120W

15A

180W(3sec.)

100mVp-p

12~14V

1.0%

0.5%

1.0%

Features :

SDR-120 series

WITHSTANDVOLTAGE

ISOLATIONRESISTANCE

I/P-O/P:3KVACI/P-FG:1.5KVACO/P-FG:0.5KVAC O/P-DCOK:0.5KVAC

I/P-O/P,I/P-FG,O/P-FG:>100MOhms/500VDC/25 /70%RH

ENVIRONMENT

SAFETY &

FUNCTION

EMC

(Note4)

PROTECTION

RIPPLE&NOISE(max.) Note.2

VOLTAGETOLERANCE Note.3

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.

In case the adjacent device is a heat source, 15mm clearance is recommended.

6. 3 seconds max., please refer to peak loading curves.

7. Derating may be needed under low input voltage. Please check the derating curve for more details.

120WSingleOutputIndustrialDINRAIL withPFCFunction

High efficiency 91% and low power dissipation

Built-in active PFC function, PF>0.93

Protections: Short circuit / Overload / Over voltage / Over temperature

Cooling by free air convection

Can be installed on DIN rail TS-35/7.5 or 15

UL 508 (industrial control equipment) approved

EN61000-6-2(EN50082-2) industrial immunity level

100% full load burn-in test

3 years warranty

150% peak load capability

Built-in DC OK relay contact

FileName:SDR-120-SPEC2011-08-23

SEMIF47

EMCIMMUNITY

EMCEMISSION