ACDC 15 Watts EML15 Series xppower.com * Ultra Compact Size * Medical Approvals * Single Outputs from 3.3 to 48 V * PCB Mount, Open Frame & Chassis Mount * Encapsulated PCB & Chassis Mount * Class II * Peak Load Capability Specification Input Input Voltage Input Frequency Input Current Inrush Current Earth Leakage Current Input Protection General * * * * * * 85-264 VAC (120-370 VDC) 47-63 Hz 0.3 A rms at 230 VAC 20 A at 115 VAC, 40 A at 230 VAC, Class II construction no earth Internal 2 A fuse Output * * * * * * See tables 4000 VAC Input to Output Primary to Secondary 2 MOPP 70 kHz typical 4.8 W/In3 (PCB Mount version) >400 kHrs per MIL-HDBK-217F Environmental Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load Start Up Delay Start Up Rise Time Hold Up Time Line Regulation Load Regulation Transient Response * * * * * * * * * * Ripple & Noise * Overvoltage Protection Overload Protection Short Circuit Protection Temperature Coefficient Efficiency Isolation Protection Level Switching Frequency Power Density MTBF * * * * See tables 5% (not encapsulated units) 1% No minimum load required 2 s max 14 ms max 12 ms min at full load & 115 VAC 0.5% max 1% max 4% max deviation, recovery to within 1% in 500 s for a 25% load change 3.3-5 V versions: 50 mV pk-pk, 12-15 V versions: 120 mV pk-pk, 24-48 V versions: 200 mV pk-pk, 20 MHz BW 115-135% Vnom, recycle input to reset 120-150% Trip and restart (Hiccup mode) 0.05%/C Operating Temperature * -20 C to +70 C, derate linearly from 100% at +50 C to 50% at +70 C Cooling * Convection-cooled Operating Humidity * 95% RH, non-condensing Storage Temperature * -40 C to +85 C Operating Altitude * 3048 m Vibration * IEC68-2-6, 2 g, 10 Hz to 500 kHz, 10 mins/cycle, 60 mins each cycle Shock * IEC68-2-27, 30 g, 11 ms half sine, 3 times in each of 6 axes EMC & Safety Emissions Harmonic Currents ESD Immunity Radiated Immunity * * * * EFT/Burst Surge Conducted Immunity Magnetic Fields Dips & Interruptions * * * * * Safety Approvals * EN55022, level B conducted & radiated EN61000-3-2, EN61000-3-3 EN61000-4-2, level 3 Perf Criteria A EN61000-4-3, 10 V/m 80% mod Perf Criteria A EN61000-4-4, level 3 Perf Criteria A EN61000-4-5, level 3 Perf Criteria A EN61000-4-6, 10 Vrms Perf Criteria A EN61000-4-8, 10 A/m Perf Criteria A EN60601-1-2, 70% UT for 500 ms, 40%UT for 100 ms, <5% UT for 10 ms, <5% UT for 5000 ms, Perf Criteria A, A, A, B (see Note 4) EN60601-1, AN51/AAIMT ES60601-1. IEC60601-1 Output Power 10 W 15 W 15 W 15 W 15 W 15 W 15 W 15 W Output Voltage 3.3 VDC 5.0 VDC 9.0 VDC 12.0 VDC 15.0 VDC 24.0 VDC 36.0 VDC 48.0 VDC Output Current Nominal 3.00 A 3.00 A 1.67 A 1.25 A 1.00 A 0.63 A 0.42 A 0.32 A Model Number(2) EML15US03 EML15US05 EML15US09 EML15US12 EML15US15 EML15US24 EML15US36 EML15US48 Efficiency Peak(1) 3.90 A 3.90 A 2.17 A 1.62 A 1.30 A 0.82 A 0.54 A 0.41 A 75% 78% 80% 80% 80% 82% 82% 82% Notes 1. Peak load lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal. 2. Add suffix to model number to define type: add `-P' for PCB mount, add `-T' for chassis mount, add `-E' for encapsulated, add `-S' for screw terminals. 3. A Screw terminal version (-S) is available with DIN clip attached, add suffix `D', e.g. EML15US24-SD, DIN rail mounting kit is available as a seperate item, order code ECL15 DIN CLIP. 4. 40% of UT dip is performance criteria A if load is reduced 45% based on 100VAC. Mechanical Details Encapsulated (E) Open Frame PCB Mount (P) 0.50 (12.6) 2.44 (62.0) -Vo -Vo ACN 1.21 (30.7) +Vo 0.69 (17.5) ACL 0.06 (1.6) 1.31 (33.3) 0.79 (20.1) 4x o 0.04 (o1.0) 0.39 (10.0) -Vout +Vout 2.95 (75.0) 1.25 (31.8) Pin1 Pin2 Pin3 Pin4 Screw Terminal (S) ) 20 (3. 0.950 (24.13) NP ACL 26 0.1 0.150 (3.81) 4- Pin1: 0.21 (5.4) 0.96 (24.4) 0.78 (20.0) max Open Frame Chassis Mount (T) Pin2: 2.13 (54.1) 2.56 (65.0) 0.36 (9.1) o 0.07 (o1.8) ACN 0.79 (20.1) 0.69 (17.5) 2.13 (54.1) o 0.04 (o1.0) Pin3: +Vo V Adj. 0.15 (3.9) 0.11 (2.9) TOP VIEW ACL 0.17 (4.4) 0.15 (3.8) ACN 1.36 (34.5) TOP VIEW ACN 1.00 ACL (25.4) 4x o 0.14 (4x o 3.5) -Vo +Vo 0.44 (11.1) 0.150 (3.81) 2.54 (64.5) 0.39 (10.0) 2.800 (71.12) 3.10 (78.7) 0.12 (3.1) Max 0.79 (20.0) max 1 1.04 (26.4) 0.27 0.09 (6.8) (2.5) 3.30 (84.0) Optional DIN clip Notes 1. Dimensions in inches (mm). 2. Weight: EML15 P Version: 0.07 lbs (35 g) T Version: 0.07 lbs (35 g) E Version: 0.20 lbs (90 g) S Version: 0.24 lbs (110 g) 3. Tolerances: x.xx = 0.02 (x.x = 0.5) x.xxx = 0.01 (x.xx = 0.25) Mating Connectors (-T version only) Input Connector: JST XHP-3 Output Connector: JST XHP-4 Crimps: SPH-002T-P0.5S Cable harness with 300 mm wire available, order part no. ECL15 LOOM KIT 25-Jun-13 ACDC EML15 Models and Ratings