Page 1HPR10XX REV C 9/98
DC/DC CONVERTERS
HPR10XX
Notes: All dimensions are in inches (millimeters).
GRID: 0.100 inches (2.54 millimeters)
PIN PLACEMENT TOLERANCE: ± 0.015"
Internet: http://www .cdpow erelectronics.com
Power Electronics Division, United States
3400 E Britannia Drive, Tucson, Arizona 85706
Phone: 520.295.4100 Fax: 520.770.9369
Power Electronics Division, Europe
C&D Technologies (Pow er Electronics) Ltd.
132 Shannon Industrial Estate, Shannon, Co. Clare, Ireland
Tel: +353.61.474.133 Fax:+353.61.474.141
FEATURES
●●
●●
●LOW COST
●●
●●
●SINGLE-IN-LINE PACKAGE (SIP)
●●
●●
●INTERNAL INPUT AND OUTPUT FILTERING
●●
●●
●NON-CONDUCTIVE CASE
●●
●●
●HIGH OUTPUT POWER DENSITY:
13 WATTS/INCH3
●●
●●
●EXTENDED TEMPERATURE RANGE:
-25°C TO +65°C
●●
●●
●HIGH EFFICIENCY: TO 72% TYPICAL
DESCRIPTION
The HPR10XX Series uses advanced circuit design and pack-
aging technology to deliver superior reliability and perfor-
mance. A 170kHz push-pull oscillator is used in the input stage.
Beat-frequency oscillation problems are reduced when using
the HPR10XX Series with high frequency isolation amplifiers.
Reduced parts count and high efficiency add to the reliability of
the HPR10XX Series. The high efficiency of the HPR10XX
Series means less internal power dissipation, as low as 190mW.
With reduced heat dissipation the HPR10XX Series can oper-
ate at higher temperatures with no degradation. In addition, the
high efficiency of the HPR10XX Series means the series is able
to offer greater than 13 W/inch3 of output power density.
Operation down to no load will not impact the reliability of the
series, although a 1mA minimum load is needed to realize
published specifications.
The HPR10XX Series provides the user low cost without
sacrificing reliability. The use of surface mounted devices and
advanced manufacturing technologies make it possible to offer
premium performance and low cost.
FRONT
VIEW
BOTTOM
VIEW * Common pin not present on single output models.
PIN CONNECTIONS
1. +VIN 2. -VIN
4. -VOUT 5. COM*
6. +VOUT
RIGHT
SIDE
VIEW
MECHANICAL
HPR10XX
Product Data Sheet 1.0 WATT UNREGULATED
SIP DC/DC CONVERTER
Page 2 HPR10XX REV C 9/98
Specifications typical at TA = +25°C, nominal input voltage, rated output current unless otherwise specified.
ELECTRICAL SPECIFICA TIONS
Note: Other input to output voltages may be available. Please contact factory.
COMMON SPECIFICA TIONS
Specifications typical at TA = +25°C, nominal input voltage, rated output current unless otherwise specified.
* For demonstrated MTTF results reference Reliability Report HPR105
NOMINAL RATED RATED INPUT CURRENT REFLECTED
INPUT OUTPUT OUTPUT RIPPLE EFFICIENCY
VOLTAGE VOLTAGE CURRENT NO LOAD RATED LOAD CURRENT
MODEL (VDC) (VDC) (mA) (mA) (mA) (mAp-p) (%)
HPR1000 5 5 200 33 290 8 68
HPR1001 5 12 83 33 290 8 69
HPR1002 5 15 67 33 285 8 70
HPR1003 5 ±5 ±100 33 285 8 70
HPR1004 5 ±12 ±42 33 285 8 70
HPR1005 5 ±15 ±34 33 285 8 70
HPR1006 12 5 200 18 110 10 70
HPR1007 12 12 83 18 107 10 71
HPR1008 12 15 67 18 107 10 71
HPR1009 12 ±5 ±100 18 107 10 71
HPR1010 12 ±12 ±42 18 107 10 71
HPR1011 12 ±15 ±34 18 107 10 71
HPR1012 15 5 200 15 96 10 70
HPR1013 15 12 83 15 94 10 70
HPR1014 15 15 67 15 94 10 71
HPR1015
HPR1016 15 ±12 ±42 15 94 10 71
HPR1017 15 ±15 ±34 15 94 10 71
HPR1018 24 5 200 12 60 15 71
HPR1019 24 12 83 12 60 15 71
HPR1020 24 15 67 12 58 15 72
HPR1021 24 ±5 ±100 12 58 15 72
HPR1022 24 ±12 ±42 12 58 15 72
HPR1023 24 ±15 ±34 12 58 15 72
PARAMETER CONDITIONS MIN TYP MAX UNITS
INPUT
Voltage Range 4.5 5 5.5 VDC
10.8 12 13.2 VDC
13.5 15 16.5 VDC
21.6 24 26.4 VDC
Voltage Rise Time See Typical Performance Curves & Application Notes: "Capacitive Loading Ef fects on Start-Up of DC/DC Converters"
ISOLATION
Rated Voltage 1000 VDC
Test Voltage 60 Hz, 10 Seconds 1000 Vpk
Resistance 10 GΩ
Capacitance 25 100 pF
Leakage Current VISO= 240VAC, 60Hz 2 8.5 µArms
OUTPUT
Rated Power 1.0 W
Voltage Setpoint Accuracy Rated Load, Nominal VIN ±5 %
Ripple & Noise BW = DC to 10MHz 100 mVp-p
BW =10Hz to 2MHz 30 mVrms
Voltage 1mA Load, VOUT = 5V 7 VDC
1mA Load, VOUT = 12V 15 VDC
1mA Load, VOUT = 15V 18 VDC
Temperature Coefficent .01 %/Deg C
REGULATION
Line Regulation High Line to Low Line 1 %/%Vin
Load Regulation (5V out only) Rated Load to 1mA Load 10 %
Load Regulation (All other Models) Rated Load to 1mA Load 3 %
GENERAL
Switching Frequency 170 kHz
Frequency Change Over Line and Load 24 %
Package Weight 2g
MTTF per MIL-HDBK-217, Rev. E Circuit Stress Method
Ground Benign TA = +25°C 3.8 MHr
Fixed Ground TA = +35°C 1. 4 MHr
Naval Sheltered TA = +35°C 685 kHr
Airborne Uninhabited Fighter TA = +35°C 211 kHr
TEMPERATURE
Specification -25 +25 +65 °C
Storage -50 +110 °C
Page 3HPR10XX REV C 9/98
SAFE OPERATING AREA
Rise Time of Input Voltage (mS)
LOAD CAPACITANCE vs INPUT RISE TIME
(5 Vout models)
Total Load Capacitance (uF)
0 5 10 15 20 25 30 35 40 45 50
600
500
400
300
200
100
0
SAFE OPERATING AREA
Rise Time of Input Voltage (mS)
LOAD CAPACITANCE vs INPUT RISE TIME
(12 Vout models)
Total Load Capacitance (uF)
0 5 10 15 20 25 30 35 40 45 50
90
80
70
60
50
40
30
20
10
0
SAFE OPERATING AREA
Rise Time of Input Voltage (mS)
LOAD CAPACITANCE vs INPUT RISE TIME
(15 Vout models)
Total Load Capacitance (uF)
0 5 10 15 20 25 30 35 40 45 50
60
50
40
30
20
10
0
VOUT VS LOAD
(5Vout Models) VOUT VS LOAD
(±5Vout Models) VOUT VS LOAD
(12Vout Models)
VOUT VS LOAD
(±12Vout Models) VOUT VS LOAD
(15Vout Models) VOUT VS LOAD
(±15Vout Models)
0 40 120 160
5.3
5.5
5.7
4.9
5.1
020406080
11.9
12.0
12.1
12.2
12.3
12.4
020406080
4.6
4.8
5.0
5.2
5.4
010203040
12.0
12.1
12.2
12.3
12.4
12.5
14.9
15.1
15.3
15.5
15.7
15.9
020406080 0
13.5
14.0
14.5
15.0
15.5
16.0
Vout
Vout
Vout
Vout
Vout
Vout
Efficiency (%)
80
Output Current (mA) Output Current each load (mA) Output Current each load (mA)
12.5
Output Current each load (mA)
12.6
Output Current each load (mA) Output Power each load (Watts)
0.2 0.4 0.6 0.8 1.0
16.5
040 80 100
60
20
90
75
60
45
30
15
0
EFFICIENCY VS LOAD
% of Rated Load (%)
Efficiency (%)
OSCILLATION FREQUENCY VS
TEMPERATURE
220
200
180
160
140-30 0 30 60 90
Temperature (°C)
TYPICAL PERFORMANCE CURVES
Specifications typical at TA = +25°C, nominal input voltage, rated output current unless otherwise specified.
SAFE OPERATING AREA
NOTES:
1.) When operated within the SAFE OPERATING AREA as defined
by the above curves, the output voltage of HPR10XX devices is
guaranteed to be within 95% of its steady-state value within 100
milliseconds after the input voltage has reached 95% of its steady-
state value.
2.) For dual output models, total load capacitance is the sum of the
capacitances on the plus and minus outputs.
Page 4 HPR10XX REV C 9/98
The information provided herein is believed to be reliable; however, C&D TECHNOLOGIES assumes no responsibility for inaccuracies or omissions. C&D TECHNOLOGIES assumes no responsibility for the use of
this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein
are implied or granted to any third party. C&D TECHNOLOGIES does not authorize or warrant any C&D TECHNOLOGIES product for use in life support devices/systems or in aircraft control applications.
ENGINEERING NOTES
ORDERING INFORMATION
Device Family
HPR Indicates DC/DC Converter
Model Number
Selected from Table of Electrical Characteristics
Screening Option
HPR 10XX /H
ABSOLUTE MAXIMUM RATINGS
Internal Power Dissipation.....................................................490mW
Short Circuit Duration......................................................Momentary
Lead Temperature (soldering, 10 seconds max)..................+300°C
