INDUCTORS
MLK0603 0603 [0201 inch]*
MLK1005 1005 [0402 inch]
* Dimensions Code JIS[EIA]
October 2013
Inductors for High Frequency
Multilayer Ceramic
MLK series
(2/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
Inductors for High Frequency Circuits
Multilayer Ceramic
FEATURES
With the adoption of a giga-spiral laminated structure, a self-resonant frequency higher than that of the MLG structure can be obtained,
while the decrease of Q in the GHz band is limited.
Monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for high-frequency.
There is no directivity.
APPLICATION
Smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners
and other high frequency circuits for the mobile communication industry
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Overview of the MLK Series
MLK 0603 L 1N1 J T □□□
Series name L×W×H Dimensions Characteristics Inductance Inductance
tolerance Packaging style Internal code
(mm) (µH)
0603 0.6×0.3×0.3 L 1N1 1.1 S ±0.3nH T Taping
1005 1.0×0.5×0.5 S 11N 11 J ±5%
R10 100
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C）(pieces/reel) （mg）
MLK0603 –55 to +125 –55 to +125 15000 0.2
MLK1005 –55 to +125 –55 to +125 10000 1
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
Overview of the MLK Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series
MLK0603 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
0.6±0.03
0.15±0.05 0.15±0.05
0.30±0.03 0.30±0.03
Dimensions in mm
0.3
0.3 0.250.25
(6/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series MLK0603 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 The " □□□ " of the Part Number contains the internal code.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LL measuring
frequency
(MHz)
Q
min.
Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
()
Rated current
(mA)
max.
Part No.*
(nH) Tolerance min. typ. max. typ.
1.0 ±0.3nH 100 6 300 12.0 17.1 0.20 0.09 300 MLK0603L1N0ST□□□
1.1 ±0.3nH 100 6300 11.0 17.1 0.22 0.10 300 MLK0603L1N1ST□□□
1.2 ±0.3nH 100 6 300 11.0 16.1 0.22 0.11 300 MLK0603L1N2ST□□□
1.3 ±0.3nH 100 6300 10.0 15.8 0.24 0.12 300 MLK0603L1N3ST□□□
1.5 ±0.3nH 100 6 300 10.0 14.9 0.24 0.12 300 MLK0603L1N5ST□□□
1.6 ±0.3nH 100 6300 10.0 14.3 0.27 0.13 300 MLK0603L1N6ST□□□
1.8 ±0.3nH 100 6 300 10.0 13.8 0.27 0.14 300 MLK0603L1N8ST□□□
2.0 ±0.3nH 100 6300 9.0 12.6 0.30 0.15 300 MLK0603L2N0ST□□□
2.2 ±0.3nH 100 6 300 9.0 12.5 0.30 0.17 300 MLK0603L2N2ST□□□
2.4 ±0.3nH 100 6300 8.5 11.4 0.35 0.17 300 MLK0603L2N4ST□□□
2.7 ±0.3nH 100 6 300 8.5 10.9 0.35 0.18 300 MLK0603L2N7ST□□□
3.0 ±0.3nH 100 6300 8.0 10.6 0.40 0.20 200 MLK0603L3N0ST□□□
3.3 ±0.3nH 100 6 300 8.0 10.5 0.40 0.22 200 MLK0603L3N3ST□□□
3.6 ±0.3nH 100 6300 8.0 9.9 0.45 0.22 200 MLK0603L3N6ST□□□
3.9 ±0.3nH 100 6 300 8.0 9.8 0.45 0.25 200 MLK0603L3N9ST□□□
4.3 ±0.3nH 100 6300 7.5 9.5 0.50 0.28 200 MLK0603L4N3ST□□□
4.7 ±0.3nH 100 6 300 7.5 9.5 0.50 0.28 200 MLK0603L4N7ST□□□
5.1 ±0.3nH 100 6300 6.5 8.8 0.60 0.28 200 MLK0603L5N1ST□□□
5.6 ±0.3nH 100 6 300 6.5 8.5 0.60 0.30 200 MLK0603L5N6ST□□□
6.2 ±0.3nH 100 6300 6.0 8.3 0.65 0.34 200 MLK0603L6N2ST□□□
6.8 ±5% 100 6 300 6.0 8.1 0.65 0.34 200 MLK0603L6N8JT□□□
7.5 ±5% 100 6300 6.0 7.7 0.70 0.36 200 MLK0603L7N5JT□□□
8.2 ±5% 100 6 300 6.0 7.9 0.70 0.41 200 MLK0603L8N2JT□□□
9.1 ±5% 100 6300 5.5 7.4 0.80 0.42 200 MLK0603L9N1JT□□□
10 ±5% 100 6 300 5.5 7.5 0.80 0.48 200 MLK0603L10NJT□□□
12 ±5% 100 6300 5.0 6.9 1.00 0.54 150 MLK0603L12NJT□□□
15 ±5% 100 6 300 4.5 6.6 1.10 0.66 150 MLK0603L15NJT□□□
18 ±5% 100 6300 4.0 5.8 1.30 0.85 100 MLK0603L18NJT□□□
22 ±5% 100 6 300 3.5 5.3 1.60 1.02 100 MLK0603L22NJT□□□
27 ±5% 100 6300 3.0 4.6 1.70 1.09 100 MLK0603L27NJT□□□
33 ±5% 100 6 300 2.8 4.4 1.80 1.21 100 MLK0603L33NJT□□□
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(7/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series MLK0603 Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
 The " □□□ " of the Part Number contains the internal code.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
0.9 0.9 0.9 0.9 0.9 10 12 19 20 22 MLK0603L1N0ST□□□
1.0 1.0 0.9 0.9 0.9 9 11 17 18 20 MLK0603L1N1ST□□□
1.1 1.0 1.0 1.0 1.0 9 12 18 19 21 MLK0603L1N2ST□□□
1.2 1.1 1.1 1.1 1.1 9 12 18 19 21 MLK0603L1N3ST□□□
1.3 1.3 1.3 1.3 1.3 9 12 18 19 21 MLK0603L1N5ST□□□
1.4 1.4 1.4 1.4 1.4 9 12 18 19 21 MLK0603L1N6ST□□□
1.6 1.6 1.6 1.6 1.6 9 11 17 18 20 MLK0603L1N8ST□□□
1.8 1.7 1.7 1.7 1.7 9 12 17 18 20 MLK0603L2N0ST□□□
2.0 1.9 1.9 1.9 2.0 10 12 19 20 22 MLK0603L2N2ST□□□
2.1 2.1 2.1 2.1 2.1 9 12 18 19 20 MLK0603L2N4ST□□□
2.4 2.4 2.4 2.4 2.4 10 13 19 20 22 MLK0603L2N7ST□□□
2.7 2.6 2.6 2.6 2.7 9 12 18 19 21 MLK0603L3N0ST□□□
3.0 2.9 2.9 3.0 3.0 10 13 19 20 22 MLK0603L3N3ST□□□
3.2 3.1 3.1 3.1 3.2 9 11 17 18 19 MLK0603L3N6ST□□□
3.5 3.4 3.5 3.5 3.5 10 13 19 20 22 MLK0603L3N9ST□□□
3.8 3.8 3.8 3.8 3.9 10 12 18 19 20 MLK0603L4N3ST□□□
4.2 4.2 4.2 4.2 4.3 10 13 19 20 22 MLK0603L4N7ST□□□
4.6 4.5 4.5 4.6 4.7 10 12 18 19 21 MLK0603L5N1ST□□□
5.0 5.0 5.0 5.0 5.1 10 12 18 19 21 MLK0603L5N6ST□□□
5.5 5.5 5.5 5.6 5.7 10 12 18 19 20 MLK0603L6N2ST□□□
6.2 6.1 6.2 6.2 6.4 10 13 19 20 22 MLK0603L6N8JT□□□
6.7 6.6 6.7 6.8 7.0 10 12 18 19 20 MLK0603L7N5JT□□□
7.4 7.3 7.5 7.6 7.8 10 13 19 20 21 MLK0603L8N2JT□□□
8.2 8.1 8.3 8.4 8.6 10 12 18 18 20 MLK0603L9N1JT□□□
9.0 8.9 9.2 9.3 9.6 10 13 18 19 20 MLK0603L10NJT□□□
10.8 10.6 11.0 11.2 11.6 10 12 18 18 20 MLK0603L12NJT□□□
13.5 13.4 13.9 14.2 14.8 10 12 17 18 19 MLK0603L15NJT□□□
16.2 16.1 17.0 17.4 18.4 10 12 16 17 18 MLK0603L18NJT□□□
19.8 19.7 20.9 21.5 22.8 10 12 16 16 17 MLK0603L22NJT□□□
24.4 24.4 27.2 28.6 31.7 10 12 15 15 14 MLK0603L27NJT□□□
29.7 29.7 33.4 35.1 39.3 9 11 14 14 13 MLK0603L33NJT□□□
Product No. Manufacturer
4291B+16197A Agilent Technologies
(8/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series MLK0603 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
10 100 1000 10000
0
1000
100
10
1
Frequency(MHz)
Inductance(nH)
33N
27N
22N
18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
Product No. Manufacturer
E4991A+16197A Agilent Technologies
(9/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series MLK0603 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
Q
10 100 1000 10000
Frequency(MHz)
33N
27N
22N
18N
15N
12N
10N
8N2
4N7
3N3
1N2
1N0
3N9
2N7
2N2
1N5
6N8
5N6
1N8
Product No. Manufacturer
E4991A+16197A Agilent Technologies
(10/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series
MLK1005 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
1.00±0.10
0.1min. 0.1min.
0.50±0.10 0.50±0.10
Dimensions in mm
0.5
0.5 0.4 0.5
(11/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series MLK1005 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 The " △" of the Part Number contains the inductance tolerance code, S(±0.3nH) or J(±5%).
 The " □□□ " of the Part Number contains the internal code.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
()
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
1.0 ±0.3nH 5 100 12.0 16.9 0.10 0.05 500 MLK1005S1N0△T□□□
1.1 ±0.3nH 5100 11.5 14.8 0.12 0.05 500 MLK1005S1N1△T□□□
1.2 ±0.3nH 5 100 11.0 14.4 0.12 0.05 500 MLK1005S1N2△T□□□
1.3 ±0.3nH 5100 10.0 12.6 0.15 0.06 500 MLK1005S1N3△T□□□
1.5 ±0.3nH 6 100 9.5 12.2 0.15 0.06 500 MLK1005S1N5△T□□□
1.6 ±0.3nH 6100 9.0 11.9 0.17 0.06 500 MLK1005S1N6△T□□□
1.8 ±0.3nH 6 100 8.5 10.9 0.17 0.07 500 MLK1005S1N8△T□□□
2.0 ±0.3nH 6100 8.3 10.0 0.18 0.08 500 MLK1005S2N0△T□□□
2.2 ±0.3nH 6 100 8.0 9.6 0.18 0.08 500 MLK1005S2N2△T□□□
2.4 ±0.3nH 6100 7.8 9.5 0.20 0.09 500 MLK1005S2N4△T□□□
2.7 ±0.3nH 6 100 7.5 9.1 0.20 0.10 500 MLK1005S2N7△T□□□
3.0 ±0.3nH 6100 7.2 8.5 0.22 0.10 400 MLK1005S3N0△T□□□
3.3 ±0.3nH 7 100 7.0 8.3 0.22 0.11 400 MLK1005S3N3△T□□□
3.6 ±0.3nH 7100 6.8 8.1 0.25 0.11 400 MLK1005S3N6△T□□□
3.9 ±0.3nH 7 100 6.5 7.8 0.25 0.12 400 MLK1005S3N9△T□□□
4.3 ±0.3nH 7100 6.3 7.4 0.28 0.13 400 MLK1005S4N3△T□□□
4.7 ±0.3nH 7 100 6.0 6.9 0.28 0.13 400 MLK1005S4N7△T□□□
5.1 ±0.3nH 7100 5.8 7.0 0.30 0.15 400 MLK1005S5N1△T□□□
5.6 ±0.3nH 7 100 5.7 6.7 0.30 0.15 400 MLK1005S5N6△T□□□
6.2 ±0.3nH 7100 5.6 6.5 0.35 0.18 400 MLK1005S6N2△T□□□
6.8 ±5% 7 100 5.5 6.3 0.35 0.18 400 MLK1005S6N8△T□□□
7.5 ±5% 7100 5.0 6.0 0.38 0.20 350 MLK1005S7N5△T□□□
8.2 ±5% 7 100 5.0 6.0 0.38 0.21 350 MLK1005S8N2△T□□□
9.1 ±5% 7100 4.8 5.9 0.42 0.23 350 MLK1005S9N1△T□□□
10 ±5% 7 100 4.7 5.2 0.42 0.23 350 MLK1005S10N△T□□□
12 ±5% 7100 4.3 5.3 0.47 0.27 350 MLK1005S12N△T□□□
15 ±5% 7 100 4.0 4.8 0.50 0.33 300 MLK1005S15N△T□□□
18 ±5% 7100 4.0 4.7 0.60 0.38 250 MLK1005S18N△T□□□
22 ±5% 7 100 3.5 4.4 0.70 0.46 200 MLK1005S22N△T□□□
27 ±5% 7100 3.0 3.9 0.80 0.53 200 MLK1005S27N△T□□□
33 ±5% 7 100 2.5 3.5 0.90 0.59 200 MLK1005S33N△T□□□
39 ±5% 6100 2.0 3.1 1.00 0.65 200 MLK1005S39N△T□□□
47 ±5% 6 100 1.8 3.0 1.20 0.74 200 MLK1005S47N△T□□□
56 ±5% 6100 1.5 2.6 1.30 0.84 200 MLK1005S56N△T□□□
68 ±5% 6 100 1.4 2.4 1.50 1.01 150 MLK1005S68N△T□□□
82 ±5% 6100 1.3 2.2 1.80 1.39 150 MLK1005S82N△T□□□
100 ±5% 6 100 1.1 1.9 2.20 1.60 100 MLK1005SR10△T□□□
110 ±5% 6100 1.1 2.0 2.70 1.89 100 MLK1005SR11△T□□□
120 ±5% 6 100 1.1 1.9 3.00 2.08 100 MLK1005SR12△T□□□
130 ±5% 6100 1.1 1.8 3.30 2.28 100 MLK1005SR13△T□□□
150 ±5% 6 100 1.1 1.7 5.00 3.58 80 MLK1005SR15△T□□□
160 ±5% 6100 1.1 1.7 5.20 3.79 80 MLK1005SR16△T□□□
180 ±5% 6 100 1.1 1.6 6.00 4.28 80 MLK1005SR18△T□□□
200 ±5% 6100 1.1 1.5 6.20 4.56 70 MLK1005SR20△T□□□
220 ±5% 6 100 1.0 1.4 6.20 4.54 70 MLK1005SR22△T□□□
240 ±5% 6100 1.0 1.3 6.50 4.84 70 MLK1005SR24△T□□□
270 ±5% 6 100 0.9 1.2 6.50 4.78 70 MLK1005SR27△T□□□
300 ±5% 6100 0.9 1.2 7.50 5.37 70 MLK1005SR30△T□□□
330 ±5% 6 100 0.85 1.1 8.00 5.82 70 MLK1005SR33△T□□□
Measurement item Product No. Manufacturer
L, Q 4291B+16193A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(12/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series MLK1005 Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
 The " △" of the Part Number contains the inductance tolerance code, S(±0.3nH) or J(±5%).
 The " □□□ " of the Part Number contains the internal code.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
0.9 0.9 0.9 0.9 0.9 16 20 30 32 36 MLK1005S1N0△T□□□
1.0 1.0 1.0 1.0 1.0 16 20 32 35 39 MLK1005S1N1△T□□□
1.1 1.1 1.1 1.1 1.1 15 18 28 30 33 MLK1005S1N2△T□□□
1.2 1.2 1.2 1.2 1.2 17 20 33 35 39 MLK1005S1N3△T□□□
1.4 1.4 1.4 1.4 1.4 15 19 29 31 34 MLK1005S1N5△T□□□
1.5 1.5 1.5 1.5 1.5  
17 21 34 36 40 MLK1005S1N6△T□□□
1.7 1.7 1.7 1.7 1.7 16 21 32 33 37 MLK1005S1N8△T□□□
1.9 1.8 1.9 1.9 1.9  
16 20 32 34 38 MLK1005S2N0△T□□□
2.0 2.0 2.0 2.0 2.1 15 19 29 31 34 MLK1005S2N2△T□□□
2.2 2.2 2.2 2.3 2.3  
16 20 32 34 38 MLK1005S2N4△T□□□
2.5 2.5 2.5 2.6 2.6 17 22 33 35 39 MLK1005S2N7△T□□□
2.8 2.8 2.8 2.9 2.9  
18 22 35 36 41 MLK1005S3N0△T□□□
3.1 3.1 3.1 3.1 3.2 16 20 31 32 36 MLK1005S3N3△T□□□
3.4 3.3 3.4 3.5 3.5  
17 22 33 35 39 MLK1005S3N6△T□□□
3.7 3.6 3.7 3.7 3.8 17 21 32 33 37 MLK1005S3N9△T□□□
4.0 4.0 4.1 4.2 4.3  
17 22 34 35 39 MLK1005S4N3△T□□□
4.4 4.4 4.5 4.6 4.7 17 22 33 35 38 MLK1005S4N7△T□□□
4.8 4.8 4.9 5.0 5.1  
17 22 33 35 38 MLK1005S5N1△T□□□
5.3 5.2 5.4 5.5 5.7 17 22 33 34 38 MLK1005S5N6△T□□□
5.8 5.8 6.0 6.2 6.4  
18 23 34 35 39 MLK1005S6N2△T□□□
6.4 6.4 6.6 6.7 7.0 17 22 32 33 36 MLK1005S6N8△T□□□
7.1 7.0 7.4 7.6 7.9  
18 23 34 36 38 MLK1005S7N5△T□□□
7.7 7.7 8.1 8.3 8.6 19 23 34 36 38 MLK1005S8N2△T□□□
8.6 8.6 9.1 9.3 9.7  
18 23 34 36 38 MLK1005S9N1△T□□□
9.4 9.4 10.0 10.2 10.7 19 23 34 35 38 MLK1005S10N△T□□□
11.3 11.3 12.1 12.4 13.0 19 23 34 35 37 MLK1005S12N△T□□□
14.2 14.2 15.3 15.8 16.8 18 23 33 34 35 MLK1005S15N△T□□□
17.0 17.1 18.6 19.2 20.6 18 23 32 33 34 MLK1005S18N△T□□□
20.8 20.9 23.0 23.9 25.8 18 23 32 33 34 MLK1005S22N△T□□□
25.6 25.9 29.8 31.5 35.7 18 23 30 30 28 MLK1005S27N△T□□□
31.4 31.9 37.6 40.2  18 23 29 29  MLK1005S33N△T□□□
37.2 38.1 48.9     17 21 24     MLK1005S39N△T□□□
45.0 46.2 60.6
   18 21 24    MLK1005S47N△T□□□
53.7 55.4 76.7     17 21 22     MLK1005S56N△T□□□
65.5 68.4 105.6    17 20 18    MLK1005S68N△T□□□
79.3 83.6 142.7     16 19 15     MLK1005S82N△T□□□
97.1 103.2 199.4    15 18 13    MLK1005SR10△T□□□
107.8 115.9     16 18     MLK1005SR11△T□□□
118.0 127.8    16 18 MLK1005SR12△T□□□
127.5 139.5     14 16 MLK1005SR13△T□□□
149.4 166.0    16 17 MLK1005SR15△T□□□
160.5 179.4     16 18 MLK1005SR16△T□□□
181.1 204.1    16 17 MLK1005SR18△T□□□
202.8 231.9     15 17 MLK1005SR20△T□□□
225.7 266.8    15 15 MLK1005SR22△T□□□
248.3 299.6     14 15 MLK1005SR24△T□□□
290.0 386.0    14 12 MLK1005SR27△T□□□
323.1 432.6     14 12 MLK1005SR30△T□□□
358.9 493.1    13 12 MLK1005SR33△T□□□
Product No. Manufacturer
4291B+16193A Agilent Technologies
(13/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series MLK1005 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
10 100 1000 10000
0
1000
100
10
1
Frequency(MHz)
Inductance(nH)
R22
R33 R27 R12
R10
82N
68N
56N
47N
39N
33N
27N
22N
18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
R15
R18
Product No. Manufacturer
E4991A+16193A Agilent Technologies
(14/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series MLK1005 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Product No. Manufacturer
E4991A+16193A Agilent Technologies
(15/15)
INDUCTORS
001-01 / 20131001 / inductor_commercial_high-frequency_mlk_en.fm
• All specifications are subject to change without notice.
MLK series
Packaging Style
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
8.0±0.3 3.5±0.05
1.75±0.1
4.0±0.1
1.5 +0.1
–0.0
Sprocket hole Cavity
A
KB
2.0±0.05 2.0±0.05
160min. Taping 200min.
300min.
Drawing direction
Typ e A B K
MLK0603 0.68±0.05 0.38±0.05 0.5 max.
MLK1005 1.15±0.1 0.67±0.1 0.8 max.