Q10 Series Miniature self-contained dc photoelectric sensors Features * Self-contained dc sensors in miniature right-angle housings; only 11 mm (0.43 in) thick * Epoxy-encapsulated circuitry; IP54 (NEMA5) construction; hermetically-sealed optics * 1.8 m (70 in) opposed range or 0.5 m (20 in) diffuse range; diffuse models have sensitivity adjustment * Choose models for light operate or dark operate; choose either NPN (sinking) or PNP (sourcing) output models Note: A model with a QD connector requires an optional mating cable. Q10 Opposed Mode Emitter (E) and Receiver (R) Models Range Cable Q106E Q106EQ 2 m (6.5 ft) 3-pin Pico QD Q10AN6R Q10AN6RQ 2 m (6.5 ft) 3-pin Pico QD Supply Voltage NPN/ L.O./ PNP D.O. -- Excess Gain Beam Pattern Effective Beam: 5 mm -- 1000 Q10RN6R Q10RN6RQ 1.8 m (70 in) 2 m (6.5 ft) 3-pin Pico QD Q10AP6R Q10AP6RQ 2 m (6.5 ft) 3-pin Pico QD Q10RP6R Q10RP6RQ 2 m (6.5 ft) 3-pin Pico QD Q10 Series E X C E S S L.O. NPN 10-30V dc D.O. L.O. G A I N Q10 Series 300 mm 12 in Opposed Mode Opposed Mode 100 200 mm 8 in 100 mm 4 in 0 0 100 mm 4 in 200 mm 8 in 10 300 mm 1 .01 m .033 ft PNP 12 in 0 .1 m .33 ft 1m 3.3 ft 10 m 33 ft .5 m 20 in 1.5 m 60 in 2.0 m 80 in 2.5 m 100 in DISTANCE DISTANCE D.O. 1.0 m 40 in Q10 Diffuse Mode Models Range Q10AN6D Q10AN6DQ Cable Supply Voltage NPN/ PNP 2 m (6.5 ft) 3-pin Pico QD Q10AP6D Q10AP6DQ 0.5 m (20 in) 2 m (6.5 ft) 3-pin Pico QD D.O. 10-30V dc 2 m (6.5 ft) 3-pin Pico QD L.O. PNP Q10RP6D Q10RP6DQ Printed in 2 m (6.5 ft) 3-pin Pico QD D.O. Beam Pattern Performance based on 90% reflectance white test card L.O. NPN Q10RN6D Q10RN6DQ Excess Gain L.O./ D.O. 1000 E X C E S S G A I N Q10 Series Diffuse mode Q10 Series 60 mm 2.4 in Diffuse Mode 100 40 mm 1.6 in 20 mm 0.8 in 0 10 0 20 mm 0.8 in 40 mm 1.6 in 60 mm 1 1 mm .04 in 2.4 in 0 10 mm .4 in 100 mm 4 in 1000 mm 40 in 125 mm 250 mm 375 mm 500 mm 625 mm 5 in 10 in 15 in 20 in 25 in DISTANCE DISTANCE P/N 45725 rev. B Q10 Series Product Specifications Sensing Beam Infrared, 880 nm Supply Voltage and Current 10 to 30V dc (10% maximum ripple); Emitter or receiver: 15 mA; Diffuse models: 20 mA (exclusive of load) Supply Protection Circuitry Protected against reverse polarity Output Configuration SPST solid-state dc switch; Choose NPN (current sinking) or PNP (current sourcing) models Choose light operate (N.O.) or dark operate (N.C.) models Output Rating 150 mA maximum Off-state leakage current: <10 microamps at 30V dc; On-state saturation voltage: <0.5V at 10 mA dc; <1.5V at 150 mA dc Output Protection Circuitry Protected against false pulse on power-up and continuous overload or short-circuit of outputs Overload trip point 220mA, typical, at 20C Output Response Time Opposed mode: 8 ms "on", 4 ms "off"; Diffuse mode: 3 ms "on" and "off" Repeatability Opposed mode: 1.0 ms; Diffuse mode: 0.75 ms Adjustments Diffuse models (only); single-turn, top-mounted SENSITIVITY control for adjustment of system gain (turn clockwise to increase) Indicators Opposed mode receivers and diffuse mode sensors have two LEDs: Green and Yellow GREEN glowing steadily = power to sensor is "on" GREEN flashing = output is overloaded YELLOW glowing steadily = light is sensed YELLOW flashing = marginal excess gain (1-1.5x) in light condition Emitters have one Green LED to indicate when power to sensor is "on" Construction Housings are black ABS; Rated UL 94V0 Lenses are hermetically-sealed glass; lens covers are clear acrylic Circuitry is epoxy-encapsulated and completely sealed Stainless steel M2.5 mounting hardware is included Environmental Rating IP54 (NEMA 5) Connections 2 m (6-1/2 ft) attached cable, or 3-pin pico-style quick-disconnect fitting; Cables for QD models are purchased separately Operating Temperature -40 to +70C (-40 to 158F); Maximum relative humidity 90% at 50C (non-condensing) Quick Disconnect (QD) Cables The following is the selection of cables available for the Q10 QD models Style 3-pin Pico Style Model Length For use with Pinout o10 mm max. (0.4 in) PKG3-2 2 m (6.5 ft) Black Wire straight 28 mm max. (1.1 in) All Q10 sensors with quick-disconnect fitting 3-pin Pico Style DImensions PKW3-2 Blue Wire Brown Wire 25 mm max. (1.0 in) 2 m (6.5 ft) 20 mm (0.8 in) right-angle o12 mm max. (0.5 in) page 2 Banner Engineering Corporation Q10 Series Dimensions Opposed Mode Models Diffuse Mode Models 11.0 mm (0.43 in) Yellow LED Signal Indicator (Receiver, Only) 11.0 mm (0.43 in) 21.6 mm (0.85 in) Green LED Power Indicator Yellow LED Signal Indicator (Receiver, Only) Gain (Sensitivity) Adjustment Green LED Power Indicator 15.2 mm (0.60 in) 2X Clearance for M2.5 Screw 10.0 mm (0.39 in) 14.5 mm (0.57 in) QD Models 35.0 mm (1.38 in) 18.0 mm (0.70 in) 2.8 mm (0.11 in) 2.8 mm (0.11 in) 2.8 mm (0.11 in) 2X Clearance for M2.5 Screw 20.0 mm (0.79 in) QD Models 28.9 mm (1.14 in) 42.4 mm (1.67 in) 14.5 mm (0.57 in) 2.8 mm (0.11 in) 20.0 mm (0.79 in) Hookup Diagrams Sensors with NPN Outputs Cabled Hookup Cabled Hookup bu bn bk - 10-30V dc + Load Quick-Disconnect Hookup Cabled Emitters bu + 10-30V dc - bn bu bk Load Quick-Disconnect Hookup bu - 10-30V dc bn + bk Load bn Sensors with PNP Outputs + bn 10-30V dc bu - bk Load Quick-Disconnect Emitters + 10-30V dc Banner Engineering Corporation - bn bu bk + 10-30V dc - page 3 Q10 Series Mounting Specifications Flat Mounting Stand-off Mounting M2.5 x 0.45 Machine Screw 25 mm (1.0 in) long M2.5 x 0.45 Machine Screw 12mm Long Nylon Spacer Split Lockwasher All hardware shown is supplied with each sensor. Hex Nut WARRANTY: Banner Engineering Corporation warrants it products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. ! WARNING These photoelectric presence sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor failure or malfunction can result in either an energized or a de-energized sensor output condition. Never use these products as sensing devices for personnel protection. Their use as a safety device may create an unsafe condition which could lead to serious injury or death. Only MINI-SCREENTM, MULTI-SCREENTM, MACHINE-GUARD and PERIMETER-GUARD Systems, and other systems so designated, are designed to meet OSHA and ANSI machine safety standards for point-of-operation guarding devices. No other Banner sensors or controls are designed to meet these standards, and they must NOT be used as sensing devices for personnel protection. Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 Telephone: (612) 544-3164 FAX (applications) (612) 544-3573